KV-21T5K KV-21T5R KV-21M5D KV-21T5D KV-21M5K TRINITRON COLOR TV SELF-DIAGNOSTIC FUNCTION SERVICE MANUAL

Transcription

1 MENU PROGR Layer RM-88 SELF-DIAGNOSTIC FUNCTION SERVICE MANUAL FE- CHASSIS MODEL COMMANDER DEST CHASSIS NO. MODEL COMMANDER DEST CHASSIS NO. KV-MD KV-TD KV-MK RM-88 AEP SCC-Q0M-A RM-88 AEP SCC-Q0N-A RM-88 OIRT SCC-Q0V-A KV-TK KV-TR RM-88 OIRT SCC-Q0X-A RM-88 OIRT SCC-Q0W-A N/ TRINITRON COLOR TV MICROFILM

2 ITEM MODEL Television System Channel Coverage Color System AEP B/G/H VHF : E-E, A-H, R0-R UHF : E-E69, B-B69, R-R69 CABLE TV : S0-S0, S-S0 HYPER : S-S PAL, SECAM OIRT B/G/H, D/K VHF : E-E, R0-R UHF : E-E69, R-R60 CABLE TV : S0-S0, S-S0 HYPER : S-S PAL, SECAM NTS0., NTSC.8 (VIDEO IN) MODEL MD TD MK TK TR Power Consumption 60W 60W 60W [PICTURE TUBE] Input/Output Terminals Super Trinitron Approx. cm ( inches) (Approx. cm picture measured diagonally) 0 degree deflection [REAR] -pin Euro connector (CENELEC standard). - Inputs for Audio and Video signals. - Inputs for RGB. - Outputs of TV Video and Audio signals. [FRONT] Video input - phono jack Audio inputs - phono jacks Headphone jacks : minijack Sound output x.w (Music Power) Power requirements 0-0V Dimensions Approx 98x6x67mm Weight Approx kg Supplied accessories RM-88 Remote Commander () IEC designated R6 battery () Other features TELETEXT (For KV-T models) [RM-88] Remote control system Power requirements Dimensions Weight Infrared control.v dc batteries IEC designation R6 (size AA) Approx 6xxmm (w/h/d) Approx 7g (Not including battery) Design and specifications are subject to change without notice.

3 Model Name KV-MD KV-MK Item KV-TD KV-TK KV-TR Pal Comb OFF OFF OFF PIP OFF OFF OFF Woofer Box OFF OFF OFF Scart ON ON ON Scart OFF OFF OFF Front in () ON ON ON Scart OFF OFF OFF Projector OFF OFF OFF AKB in 6:9 mode ON ON ON Norm B/G ON ON ON Norm I OFF OFF OFF Norm D/K OFF ON ON Norm AUS OFF OFF OFF Norm L OFF ON OFF Norm SAT OFF OFF OFF Norm M OFF OFF OFF Language Preset German OIRT OIRT

4 Pin No Signal Signal level Audio output B (right) Audio output B (right) Audio output A (left) Ground (audio) Ground (blue) 6 Audio input A (left) Standard level : 0.V rms Output impedence : Less than kohm* Standard level : 0.V rms Output impedence : More than 0kohm* Standard level : 0.V rms Output impedence : Less than kohm* Standard level : 0.V rms Output impedence : More than 0kohm* 7 Blue input 0.7 +/- db, 7 ohms positive 8 Function select (AV control) 9 Ground (green) 0 Open High state (9.-V) : Part mode Low state (0-V) : TV mode Input impedence : More than 0K ohms Input capacitance : Less than nf Green Green signal : 0.7 +/- db, 7 ohms, positive Open Ground (red) Ground (blanking) _ Red input 0.7 +/- db, 7 ohms, positive (S signal Chroma input) 6 Blanking input (Ys signal) 7 Ground (video output) 8 Ground (video input) 0. +/- db, 7 ohms, positive High state (-V) Low state (0-0.V) Input impedence : 7 ohms 9 Video output V +/- db, 7ohms, positive sync 0.V (-+0dB) 0 _ Video input V +/- db, 7ohms, positive sync 0.V (-+0dB) Video input Y (S signal) Common ground (plug, shield) V +/- db, 7ohms, positive sync 0.V (-+0dB)

5 TABLE OF CONTENTS Section Title Page Section Title Page. GENERAL. DIAGRAMS. DISASSEMBLY Overview of TV buttons...6 Using Select Mode...6 usting the Picture...7 Using the Sleep Timer...7 Using the Wake Up Timer...8 Viewing Teletext...8 Exchanging Programme Pos...9 Manually Tuning the TV...9 Fine-Tuning Channels...0 Skipping Programme Pos...0 Using Optional Equipment... Troubleshooting Rear Cover Removal Chassis Assy Removal Service Position Picture Tube Removal Block Diagrams Circuit Board Location Schematic Diagrams and Printed Wiring Boards...7 * A Board... * C Board Semiconductors IC Blocks EXPLODED VIEWS 6-. Chassis Picture Tube ELECTRICAL PARTS LIST.... SET-UP ADJUSTMENTS -. Beam Landing Convergence Screen [G] White Balance Focus...7. CIRCUIT ADJUSTMENTS -. Electrical ustments Test Mode FE- Self Diagnostic Software... CAUTION SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE ANODE CAP WARNING!! AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE POWER LINE. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARKED ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION APRES AVOIR DECONNECTE LE CAP DE LANODE, COURT-CIRCUITER L ANODE DU TUBE CATHODIQUE ET CELUI DE L ANODE DU CAP AU CHASSIS METALLIQUE DE L APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE. ATTENTION!! AFIN D EVITER TOUT RISQUE D ELECTROCUTION PROVENANT D UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR D ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE. LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ Á L ALIMENTATION SECTEUR. ATTENTION AUX COMPOSANTS RELATIFS Á LA SÈCURITÈ!! LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES EXPLOSÈES ET LES LISTES DE PIECES SONT D UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.

6 SELECT SELECT SELECT OK SECTION GENERAL The operating instructions mentioned here are partial abstracts from the Operating Manual. The page numbers of the Operating Instruction Manual remain as in the manual. Basic TV Features Overview of TV Buttons Additional TV Features Using Select Mode You can select different preset picture modes. / Press the MENU button on the remote control to display the menu on the TV screen. On/Off Switch. Video Input Button. (selects input signals from VCR etc.). Auto Tune Button. Volume Control Buttons. With the cursor pointing at the SELECT symbol on the TV screen as shown, press the yellow button. Programme Up or Down Buttons. (selects TV channels). Press the blue button to select the desired mode: Overview of Remote Control Buttons MENU Personal Mode - reverts to settings made in usting the Picture section of the manual. Movie Mode - for films Live Mode - for live broadcast programmes 6 To Mute Sound Press to mute TV sound. Press again to restore the sound. To Select Channels Press to select channels. For double-digit programme numbers, e.g., press -/-- first, then the buttons and. If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting -/-- button again to enter the programme number of your choice To Change Screen Format / MENU To Temporarily Switch Off TV Press to temporarily switch off TV. Press again to switch on TV from standby mode. To save energy we recommend switching off completely when TV is not in use. NOTE: After - 0 minutes without a TV signal and without any button being pressed, the TV switches automatically into standby mode. To Reveal On Screen Information Press to reveal all on-screen indications. Press again to cancel. PROGR RM-88 Press the MENU button to remove the menu display from the TV screen. Note: The mode selected in step is now stored. Changing Modes Quickly Press the button on the remote control to display the three different modes. Press the button again to select your desired mode. Press to view programmes in 6:9 mode. Press again to return to : mode. PROGR To ust TV Volume To Select Channels Press to adjust the volume of the TV. Press to select channels. RM

7 SELECT SELECT SELECT SELECT SELECT OK Additional TV Features usting the Picture Although the picture is adjusted at the factory, you can modify it to suit your own requirement. Additional TV Features Using the Sleep Timer The TV may be set to switch automatically to the standby mode after a length of time chosen by you. You may set the time in minute steps up to hours. / Press the button on the remote control to display the three different modes on the TV screen. / Press the MENU button on the remote control to display the menu on the TV screen. Press the button to highlight the personal mode symbol as shown. Press the blue button on the control to select the symbol on the TV screen, then press the yellow button. Press the MENU button to display the menu on the TV screen. MENU MENU Press the yellow button repeatedly until the required amount of time delay appears on the screen. 0: OFF PROGR Press the blue button on the control to select the symbol on the TV screen then press the yellow button. PROGR 7 RM-88 Press the blue button to select the item you wish to change (see below). IIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIIIIIIIIIIIII RM-88 Once the time delay has been selected, press the MENU button to remove the on-screen display. One minute before standby, the display shown appears on the screen. 0:9 6 Press the red or yellow button to alter the selected item. Notes: 7 Press the MENU button to remove the menu display from the TV screen. When watching TV, press the button to display time remaining. To return to normal operation from standby mode, press the / button. Symbol Item Contrast Colour Brightness Sharpness Reset - resets to factory preset picture level Represents the mode selected in the Using Select Mode section. 9 0

8 SELECT SELECT SELECT OK Index Programme News Sport Weather 0 98 Additional TV Features Using the Wake Up Timer The TV may be set to switch on automatically after a length of time chosen by you. You may set the time in minute steps up to hours. Additional TV Features Viewing Teletext (KV-TD only) Teletext is an information service transmitted by most TV stations. / Press the MENU button on the remote control to display the menu on the TV screen. / Selecting Teletext Press a number button on the remote control to select the channel which carries the teletext service you wish to receive. Press the blue button on the control to select the symbol on the TV screen, then press the yellow button. Press the button on the remote control to switch on teletext. TELETEXT Index Programme News Sport 0 Weather 98 TELETEXT Input three digits for the page number using the numbered buttons on the control. MENU Press the blue button on the control to select the symbol on the TV screen, then press the yellow button. OFF OFF MENU Press the button to switch off teletext. Note: Teletext errors may occur if the broadcasting signals are weak. 8 PROGR RM-88 Press the red or yellow button to set the time. 0:00 (OFF) 0: 0:0 0: -----:00 Press the standby button /. The standby indicator on the TV flashes regularly to indicate that the Wake Up Timer is active. After the selected length of time, the TV switches on automatically. OFF 0: PROGR RM-88 Using Other Teletext Functions To Superimpose Teletext on to the TV Press once in teletext mode or twice in TV mode to superimpose teletext on to the TV screen. Press again to cancel teletext mode. To Move to Next or Preceding Page Press PROGR +/- on the remote control to select the previous or next page. TELETEXT Index Programme News Sport 0 Weather 98 TELETEXT Index Programme News Sport 0 Weather 98 Notes: If you use the Wake Up Timer to switch the TV on and for one hour after switching on, no TV or Remote Control button is pressed, the TV switches itself back into Standby mode and the indicator on the TV lights. Any temporary power failure will cause a misfunction in the Wake Up Timer and you will have to reset the Wake Up Timer. To Freeze a Teletext Page Press on the control to freeze the page. Press again to cancel the freeze. Revealing concealed information (eg: answers to a quiz). Press to reveal information. Press again to conceal the information. Using colour buttons to access pages (Fastext) When the colour coded menu appears at the bottom of a page, press the colour button (green, red, yellow or blue) to access the corresponding page.

9 SELECT SELECT SELECT OK SELECT SELECT SELECT OK Additional TV Features Exchanging Programme Positions After tuning you may wish to change the order in which the channels appear on the TV. You may wish for example to exchange the channel on programme number 8 with the channel on programme number. Additional TV Features Manually Tuning the TV You have already tuned the TV to receive all available channels using the `Automatically Tuning the TV' procedure at the start of this manual. You can however carry out this operation manually using the following instructions. / Press the MENU button on the remote control. / Press the MENU button on the remote control to display the menu on the TV screen. Press the blue button on the control to select on the TV screen, then press the yellow button. Press the blue button to select the symbol on the TV screen then press the yellow button. MENU Press the blue button to select then press the yellow button. PROGR 0 VL IIIIIIIIIIIIIII F COO MENU With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button on the remote control to allocate a programme number to the channel (eg PROGR 0). For double digit numbers e.g., press the -/-- button on the remote control then the corresponding numbered buttons. PROGR 0 VL IIIIIIIIIIIIIII F COO 9 PROGR With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button until the channel you wish to rearrange appears on screen, then press the blue button once. PROGR PROGR Press the blue button to select the tuning bar scale then press the yellow or red button once to start the channel search. (Yellow to search up the scale or red to search down). When a channel is found it appears on the TV screen. PROGR 0 VL IIIIIIIIIIIIIII F COO RM-88 Press the red or yellow button to select the new programme number (e.g. PROGR 0) for your selected channel. PROGR RM-88 If you do not wish to store this channel on the programme number you selected, press the yellow or red button to continue searching for the desired channel. 6 Press the blue button to select then press the yellow button to exchange the channels. PROGR If this is the channel you wish to store, press the blue button to select the symbol on the screen then press the yellow button to store. PROGR 0 VL IIIIIIIIIIIIIII F COO 7 Repeat steps to 6 if you wish to change the order of the other channels on your TV, then press MENU to return to normal TV screen. 7 Repeat steps to 6 if you wish to store more channels then press the MENU button to remove the menu from the TV screen. 8 Press the PROGR+/- button to view your selected channels on their new programme numbers.

10 SELECT SELECT SELECT OK SELECT SELECT SELECT OK Additional TV Features Fine-Tuning Channels If a channel is slightly off tune, you can use this fine tune procedure to obtain a better picture reception. Additional TV Features Skipping Programme Positions You can programme this TV to skip any unwanted programme numbers when they are selected with the PROGR +/- buttons. / With the channel you wish to fine-tune on the screen, press the MENU button on the remote control. The menu display appears on the TV screen. / Press the MENU button on the remote control to display the menu on the TV screen. Press the blue button on the remote control to select the symbol on the TV screen then press the yellow button. Press the blue button on the control to select the symbol on the TV screen then press the yellow button. MENU Press the blue button to select the F symbol on the TV screen then press the red or yellow button to adjust the tuning. PROGR 0 VL IIIIIIIIIIIIIII F COO MENU With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button on the remote control to select the programme number you want to skip. PROGR 0 VL IIIIIIIIIIIIIII F COO PROGR Press the blue button to select the symbol on the TV screen then press the yellow button to store. PROGR 0 VL IIIIIIIIIIIIIII PROGR Press the blue button to select Coo on the TV menu screen then press the yellow button on the remote control. PROGR 0 VL IIIIIIIIIIIIIII F 0 F COO COO RM-88 RM-88 Press the MENU button to remove the menu from the TV screen. Press the blue button to select the symbol on the TV screen then press the yellow button to store. PROGR 0 VL IIIIIIIIIIIIIII F COO 6 Repeat steps to to skip other unused programme positions. 7 Press the MENU button to remove the menu from the TV screen. Note: If you wish, you can still select any skipped programme number by pressing the corresponding numbered buttons on the remote control. 6

11 Optional Connections Using Optional Equipment Additional Information Troubleshooting You can connect optional audio or video equipment to your TV, such as a VCR, a camcorder or video games as shown. Front of TV Here are some simple solutions to problems which may affect the picture and sound. Select and View the Input Signal Problem Solution Connect your equipment to the designated TV socket. Press the button repeatedly on your remote control until the correct input symbol appears on the TV screen. Symbol Input signals Audio/video input signal through the Euro AV connector C RGB input signal through the Euro AV connector C Audio/video input signal through the phono sockets A Switch on the connected equipment. To return to normal TV picture, press the button on the remote control. Note: To avoid picture distortion, do not connect equipment to the A and C connectors at the same time. A B Rear of TV 8mm/Hi8 camcorder No picture (screen is dark), no sound Plug the TV in. Press the button on the front of TV. If the indicator is on press / button or a programme number button on the remote control. Check the aerial connection. Check that the selected video source is on. Turn the TV off for or seconds and then turn it on again using the button on the front of the TV. Poor or no picture (screen is dark), Using the MENU system, select the Picture but good sound ustment display. ust the brightness, picture and colour balance levels. From the Picture ustment display select to return to the factory settings. Poor picture quality when watching Press the button repeatedly on the remote control a RGB video source. until the RGB symbol is displayed on the screen. Good picture, no sound Press the +/ button on the remote control. If is displayed on the screen, press the button on the remote control. Additional Information Connecting a VCR We recommend you tune in the VCR signal to TV programme number `0' using the `Manually Tuning in the TV' section of this instruction manual. Connecting Headphones Plug in your headphones to the socket B on the front of the TV set. C No colour on colour programmes Using the MENU system, select the Picture ustment display. ust the colour balance. From the Picture ustment display select to return to the factory settings. Distorted picture when changing Turn off any equipment connected to the pin programmes or selecting teletext Euro connector on the rear of the TV. Remote control does not function Replace the batteries / The standby indicator on the Contact your nearest Sony service centre. TV flashes even though the Wake Up Timer is not in use. VCR PlayStation If you continue to have these problems, have your TV serviced by qualified personnel. NEVER open the casing yourself. Decoder 7 8

12 SECTION DISASSEMBLY -. REAR COVER REMOVAL -. CHASSIS ASSY REMOVAL Rear Cover Screws BTV x6 -. SERVICE POSITION

13 -. PICTURE TUBE REMOVAL DGC holder A Board Degaussing coils 6 Spring tension 7 C board Four PT screws 8 Anode cap Deflection yoke Picture tube 9 Cushion REMOVAL OF ANODE-CAP Note : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode. * REMOVING PROCEDURES. c a b b Turn up one side of the rubber cap in Using a thumb pull up the rubber cap the direction indicated by the arrow a firmly in the direction indicated by the arrow b HOW TO HANDLE THE ANODE-CAP Anode button When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c To prevent damaging the surface of the anode-cap do not use sharp materials. Do not apply too great a pressure on the rubber, as this may cause damage to the anode connector. A metal fitting called a shatter hook terminal is fitted inside the rubber cap. Do not turn the rubber foot over excessively this may cause damage if the shatter hook sticks out.

14 SECTION SET-UP ADJUSTMENTS When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments. Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply. Unless there are specific instructions to the contrary, set the controls and switches to the following settings : Contrast... 80% [or remote control normal] Brightness... 0% Carry out the following adjustments in this order : -. Beam Landing -. Convergence -. White balance -. Focus Note : Test equipment required. Color bar/pattern generator.. Degausser.. Oscilloscope.. Digital multimeter.. DC Power supply. Preparation: Fig. -. In order to reduce the influence of geomagnetism on the set s picture tube, face it in an easterly or westerly direction.. Switch on the TV set s power and degauss with the degausser. Purity Control For 9" models align the neck assy as indicated below. -. BEAM LANDING A buckle Neck Assy. Input an all-white signal from the pattern generator. Set the Contrast and Brightness to normal.. Set the pattern generator raster signal to all Red.. Move the deflection yolk forward and adjust with the purity control so that the Red is at the centre and the Blue and Green take up equally sized areas on each side of the screen. [See Fig.- - -].. Move the deflection yolk forward and adjust so that the entire screen becomes Red. [See Fig.-].. Switch the raster signal to Blue, then to Green and verify the purity condition. 6. When the position of the deflection yolk has been determined, fasten the deflection yolk with the screws. 7. If the beam does not land correctly in all the corners, use magnets to correct it. [See Fig.-]. Fig. - Deflection Yoke GREEN RED Purity control corrects this area. BLUE G G Disk magnets or rotatable disk magnets correct these areas (a - d). a b c d Deflection yolk positioning corrects these areas. a c Fig. - b d Fig. -

15 -. CONVERGENCE Preparation: Tilt the V.STAT magnet and adjust the static convergence by opening or closing the V.STAT magnet. Before starting this adjustment, adjust the focus, horizontal size and vertical size. Minimize the Brightness setting. Input a dot pattern from the pattern generator. () Horizontal and vertical static convergence. If the V.STAT magnet is moved in the direction of the a and b arrows, the Red, Green and Blue points move as indicated below. Centre dot R G B R G B H.STAT V.STAT Magnet C Board RV70 SCREEN RV70. [Moving horizontally], adjust the H.STAT control so that the Red, Green and Blue points are on top of each other at the centre of the screen.. [Moving vertically], adjust the V.STAT magnet so that the Red, Green and Blue points are on top of each other at the centre of the screen.. If the H.STAT variable resistor is unable to bring the Red, Green and Blue points together at the centre of the screen, adjust the horizontal convergence with the H.STAT variable resistor and the V.STAT magnet in the manner indicated below. [In this case, the H.STAT variable resistor and the V.STAT magnet influence each other].

16 () Operation of the BMC (Hexapole) magnet. R G B R G B R G B R G B R G B R G B V.STAT Purity The respective dot position resulting from moving each magnet interact, so be sure to perform adjustment whilst tracking. Use the H.STAT VR to adjust the Red, Green and Blue dots so that they coincide at the centre of the screen [by moving the dots in the horizontal direction]. BMC (Hexapole) () Dynamic convergence adjustment. Preparation: Before starting this adjustment, adjust the horizontal and vertical static convergence.. Slightly loosen the deflection yolk screws.. Remove the deflection yolk spacer.. Move the deflection yolk as indicated in the figure below and optimize the convergence.. Tighten the deflection yolk screws.. Re-install the deflection yolk spacer. R G B G R B G B G R R G B B R G B R R G B B G R B G R R G B B G R R G B 6

17 () Screen corner convergence. If you are unable to adjust the corner convergence properly, this can be corrected by the use of permalloy assemblies. a a-d: screen-corner convergence defect b -. Screen [G], White balance G Setting. Input a dot signal from the pattern generator.. Set the Picture, Brightness and Colour to minimum.. Apply 70Vdc from an external power supply to the R, G and B cathodes of the CRT.. Whilst watching the picture, adjust the G control [RV SCREEN] located on the FBT to the point just before the flyback return lines disappear. c d White balance adjustment b Fit the permalloy assembly to the rear of the CRT to correct the area at fault. a. Input a PAL all-white signal from the pattern generator.. Enter into the Service Mode.. Enter into the Picture service menu.. Select the Green drive and adjust so that the White Balance becomes optimum.. Select the Blue drive and adjust so that the White Balance becomes optimum. 6. Set the Picture to MIN. 7. Set the R-cut-off to ust the G-cut-off, and the B-cut-off so that the White Balance becomes optimum. 0. Press the button to return to TV operation. PICTURE Permalloy d c R - Drive G - Drive B - Drive R - cut - off G - cut - off B - cut - off ID - start 0 ID - stop 0 ID - level 0 Bellfo Sub Colour Sub Brightness -. FOCUS FOCUS SCREEN. Input a Phillips colour pattern. Set the picture settings to normal.. ust the focus control located on the Flyback transformer to bring the centre of the screen into focus. Note :Bring only the centre area of the screen into focus, switch to an all-white pattern and confirm that the magenta ring is hardly noticed. To obtain optimum focus balance the focus setting between optimum screen centre focus and a reduced magenta ring level. 7

18 SECTION CIRCUIT ADJUSTMENTS -. ELECTRICAL ADJUSTMENTS Service adjustments to this model can be performed using the supplied Remote Commander RM-88. i + (ON SCREEN DISPLAY) HOW TO ENTER INTO SERVICE MODE. Turn on the main power switch and enter into the stand-by mode.. Press the following sequence of buttons on the Remote Commander. (DIGIT ) + (VOLUME +) TT-- will appear in the upper right corner of the screen. Other status information will also be displayed. (TV). Press MENU on the remote commander to obtain the following menu on the screen. TEST MENU > Picture Geometry Sound TV Status AGC ust Technical. Move to the corresponding adjustment item using the Green [up] or Blue [down] buttons on the Remote Commander.. Press the Yellow button to enter into the required menu item. 6. Press the Menu button on the Remote Commander to quit the Service Mode when all adjustments have been completed. PICTURE R - Drive G - Drive B - Drive R - cut - off G - cut - off B - cut - off ID - start 0 ID - stop 0 ID - level 0 Bell-f0 Sub Colour Sub Brightness GEOMETRY V centre V size V Lin S Corr H Cent H Size Pin Amp Corner Pin Pin Phase V Bow V Angle Upper V Lin Lower V Lin Left HBLK 07 Right HBLK 07 CD Mode (AV) 0 SOUND Nicam Error Lower 0 Nicam Error Upper 80 Nicam Error Rate xx [Status only] AGC Gain Level xx [Status only] Note :The data shown in the TV STATUS table is dependant on destination and country. TV STATUS Destination Text Language A/L/E/U/D/B/K/R East/West 8

19 Note: Ensure that no signal is applied to the Antenna socket while carrying out the following IF adjustments. TECHNICAL GD - Secam 0 BD - Secam RC - Secam GC - Secam 9 BC - Secam 0 GD - Sports 0 BD - Sports 6 RC - Sports GC - Sports BC - Sports 7 Y - Delay (AV) 07 SUB BRIGHTNESS ADJUSTMENT. Input a Phillips colour pattern.. Press TEST TEST on the Remote Commander.. ust the Sub-Brightness data so that there is barely a difference between the 0 IRE and 0 IRE signal levels. SUB CONTRAST ADJUSTMENT. Input a video signal that contains a small 00% white area on a black background. Set the picture control to maximum. [ TT0 ]. Connect an oscilloscope to Pin of CN0 [A Board].. Enter into the Picture service menu.. ust the R - Drive data to obtain the following waveform. SYSTEM B/G, D/K, I & L I.F ADJUSTMENT. Input a 8.9Mhz carrier signal at 00dBuV to Pin [IF output] of the tuner [TU0].. Measure the voltage at Pin 7 of [IC0].. ust L0 [A Board] to obtain a voltage of.v +/- 0.V. SYSTEM L BAND I.F ADJUSTMENT. Input a.0mhz carrier signal at 00dBuV to Pin [IF output] of the tuner [TU0].. Select system L + C00 [channel 00].. Measure the voltage at Pin 7 [IC0].. ust RV0 [A Board] to obtain a voltage of.v +/- 0.V. TUNER AGC ADJUSTMENT. Receive a signal of 6dBuV / 7 ohm terminated, via the tuner antenna socket.. Connect a voltmeter to JW0 [A Board].. Enter into the Test Menu.. Select the AGC ust menu item.. ust the data using the Yellow and Green buttons on the Remote Commander to obtain a voltage of.0v +/- 0.V. ".V +/- 0.0V 9".V +/- 0.0V A RV0 R - out Waveform IC0 SUB COLOUR ADJUSTMENT 7. Receive a PAL colour bar signal.. Connect an oscilloscope to Pin of CN0 [A Board].. Enter into the Picture service menu.. ust the Sub Colour data so that the Cyan, Magenta and Blue colour bars are of equal levels as indicated below. L0 JW0 Same Level TUNER A Board component side B-Out Waveform 9

20 BELL FILTER ADJUSTMENT (Secam models only). Note : Ensure that the TV set has been powered up for at least minute to allow for drift before carrying out the following adjustment.. Input a video SECAM Colour Bar signal via AV.. Connect an oscilloscope to pin of CN0 [R-OUT] on the A board.. Enter into the Picture menu and select Bell-f0.. Decrease the register of Bell-f0 until the following waveform change between RED and BLUE is obtained. V SIZE V LIN S CORRECTION V CENTRE H CENTRE Before adjustment After adjustment H SIZE. When the correct waveform has been obtained add an additional 7 steps to the register. PIN AMP DEFLECTION SYSTEM ADJUSTMENT. Enter into the Geometry service menu.. Select and adjust each item in order to obtain the optimum image. PIN PHASE CORNER PIN GEOMETRY V centre V size V Lin S Corr H Cent H Size Pin Amp Corner Pin Pin Phase V Bow V Angle Upper V Lin Lower V Lin Left HBLK 07 Right HBLK 07 CD Mode (AV) 0 V ANGLE 0

21 -. TEST MODE : Is available by pressing TEST button twice, OSD TT appears. The functions described below are available by pressing the two numbers. To release the Test mode, press 0 twice, or switch the TV into stand-by mode, or press the TV button on the remote commander. 00 Cancel Test mode 0 Picture maximum 0 Picture minimum 0 Volume % 0 Volume 0% 0 Volume 6% 06 Volume 80% 07 Ageing mode On/Off 08 Set shipping conditions 09 Display TV Status 0 No function Sub Picture ustment Sub Colour ustment Sub Brightness ustment Text H position ustment Rotation test 6 Picture level 0% 7 Audio mute ON 8 Disable Blanking 9 No function 0 No function Destination A Destination L Destination E Destination U Destination D 6 Destination B 7 Destination K 8 Destination R 9 No function 0 No function Auto shutoff Disable/Enable RGB priority Disable/Enable Rotation On/OFF Text language East/West Wide CRT/: CRT 6 VM ON/OFF test 7 No function 8 No function 9 No function 0 No function Re-initialize the NVM [Only when Prog=9] Re-initialise geometry settings [Only when Prog=9] No function No function No function 6 No function 7 No function 8 Set NVM as NON Virgin [Only when Prog=9] 9 Set NVM as Virgin [Only when Prog=9] 0 No function No function No function No function No function No function 6 No function 7 No function 8 No function 9 No function 60 No function 6 Auto AGC ust 6 Alternative Dest B Autotuning 6 Enable/Disable Y/C input 6 Signal Quality Check for Auto Tune 6 Signal Quality NOT Checked for Auto Tune 66 No function 67 Manual AGC ust No function

22 -. FE- SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE- chassis is triggered in one of two ways :- : Busy or : Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See Table., non fatal errors are reported using this method. Each time the software detects an error it is stored within the NVM. See Table. How to enter into Table Table LED ERROR ERROR COUNT No error 00 Not allowed (may be confused with Sircs response 0 flash!) Protection circuit trip < ANY TIME > 0 Reserved 0 No vertical sync 0 AKB 0 IIC bus clock and/or data lines low at Power ON 06 NVM no IIC bus acknowledge at Power ON 07 Jungle controller no IIC acknowledge at Power ON 08 Tuner no acknowledge at Power ON 09 Sound processor no acknowledge at Power ON 0 Flash Timing Example : e.g. error number StBy LED ON ON ON. Turn on the main power switch of the TV set and enter into the Standby Mode.. Press the following sequence of buttons on the Remote Commander. i + (ON SCREEN DISPLAY) (DIGIT ) (VOLUME -) (TV). The following table will be displayed indicating the error count. Table Error Times OFF OFF Note: To clear the error count data press 80 on the Remote commander.

23 - BLOCK DIAGRAMS TU0 IF AGC CN00 SDA SCL J0 SCL POWER SUPPLY, DEFLECTION, A ( ) PROCESSOR, TUNING, VIDEO SIGNAL PROCESSOR, AV IN/OUT SDA SCL SWF 0 VIF VIF TU AGC DET OUT 6 STAND SW RF AGC AFC 7 BUFFER Q0 SYNC SEP Q00, 00 SDA +V IC0 VIF/SIF DEMODULATOR AF OUT 8 FUNCTION SWITCH S00-S006 REMOTE CONTROL RECEIVER IC00 +V IC00 RESET VIDEO AMP Q08, 09 SWITCH Q006 X00 MHZ IC00 MICRO CONTROLLER 0-COIN BE/DK/I 0-RFAGC I-AFT AGC MON AGC DEFEAT 0-BAND-M 0-BAND-L I-SIRCS I-PROCDES RESET 0-ROT/VC X-OUT X-IN 0-MSP/ASW 0-V BLK 0- +B DROP 0-VOL 0-SP MUTE OSD BLK R G B 0-WP EXT CVBS SWITCH 0-XRAY PROT Q0 0-STBY HP VP 6 7 +V MON OUT BUFFER Q0 AMPLIFIER Q007,008, 009 IC00 NVM SCLO SDAO SDA SCL 9 0 IC0 Y/C JUNGLE INT BLK INT R IN INT G IN INT B IN SDAO SCLO HP 8 Y/CVBS IN PROTECT TV/C IN MON OUT EXT B IN EXT G IN EXT R IN EXT BLK ABL IN EW VD MON OUT ABL EW VD+ L IN/IN STBY VOLUME MUTE IC0 AUDIO AMP R IN/IN L OUT/NC R OUT/OUT NC/IN 6 CN0 J0 J0 A6 L AUDIO IN A9 DET V OUT B8 MODE A8 MODE A7 BLUE A GREEN A RED A6 BLK A0 V IN B C IN B0 YV IN CN60 CN60 CN60 DGC HEADPHONES DGC CHECK DGC CHECK DGC DGC D6 RECT S60 POWER 7 T60 LINE FILTER T60 RELAY RY60 RELAY SWITCH Q60 C D IC609 STANDBY POWER MAIN RECT D60 IC606 POWER FBO CP VCC D S HD H-DRIVE Q 7 8 PH60 ISOLATOR T60 SRT 6 MUTE SW Q0 T HDT +B D60 +B RECT D6 RECT D60 RECT H-OUT Q IC60 ERROR AMP IC60 +B VREG IC60 9VREG IC608 V REG AUDIO VCC +V +9V LOW B STBY +V V- DY+ V- DY- VD+ 7 VP VD- EW IN HP PROTECT HP BOOST REF IC0 V OUTPUT 6 +B OUT D7, Q7,7 IC PIN CORRECTION 7 PIN OUT Q 6 T FBT FV ABL HV G H- DY- D -V RECT H- DY- H- DY+ H- DY+ 6 CN0 00V H DY ASSY V- DY+ V- DY- H- DY- H- DY+ TO C BOARD CN707 TO PICTURE TUBE TO C BOARD CN706 V DY H DY TO A BOARD CN0 CN70 CN707 TO A BOARD CN0 CN706 TO T FBT R G B +00V H G 000V C (RGB OUT) R DRIVE, BKG Q70, 70 G DRIVE, BKG Q70, 706 B DRIVE, BKG Q708, 709 RV70 H STAT R OUT Q70 G OUT Q 707 B OUT Q70 R G B H H RCV G H R C V G PICTURE TUBE G H V TO A BOARD T (FBT) L VD- VD- R VIDEO 8 XTAL 7 XTAL CI IN Y/CVBS IN HD 9 R OUT G OUT B OUT IK IN HD CN0 RED GREEN BLUE 6 IK TO C BOARD CN70 6

24

25

26 WAVEFORMS A BOARD PAL SECAM PAL SECAM.0 Vp-p (H). Vp-p (H).0 Vp-p (H). Vp-p (H).6 Vp-p (H) Vp-p (H) 0. Vp-p (H).0 Vp-p (H). Vp-p (H).0 Vp-p (H) Vp-p (V) Vp-p (H) Vp-p (H) 6 Vp-p (V) 90 Vp-p (H) PAL SECAM.KVp-p (H). Vp-p (H).0 Vp-p (H) WAVEFORMS C BOARD 0 Vp-p (H) 9 Vp-p (H) 9 Vp-p (H) Vp-p (H)

27 - SEMICONDUCTORS LM9N TDA8M TEA STW08FM6TR 8 DTCEK DTCEKA-T6 DTCEKA-T-6R SA07K-T-6-QR SCK-QR SCK-T-6-R DAN0K DAN0K-T6 ( TOP VIEW ) C ( TOP VIEW ) SE-N SE-N-LF TDA79 B E SC688-LK DB60L-F V OUT V IN GND SAA98PS/MA/079 SAA98PS/MA/080 SAA98PS/MA/08 SAA98PS/MA/088 TDA987-V E C B 7 6 ( TOP VIEW ) SBX98- ( TOP VIEW ) TOP09P 8 SA9AS-QRT SA9AS-RT SC70S-RT LETTER SIDE AK0VO AK0WS ERC0-6SE HZS9.NB MTZJ-T-77-.7B MTZJ-T-77-.6B MTZJ-T-77-B MTZJ-T-77-B MTZJ-T-77-A P6KE00AG RD.6ESB RD6.8ES-B RNZ-LF0-0 SS9-TD SST-77 ( TOP VIEW ) E C B CATHODE TYA780CTV STR-F66 AK0-V AU-0Z-V DINL0-TA ERB-06TP EG-Z-V ELZ ERD8-06S ERC0-06SE ERC06-S FMN-GS GP08DPKG GP0GPKG GPGPKG LSB60HL RB0V-0TE-T7 RGCLF-B RGPO-7EL-6 RGPGPKG RGP0GPKG RU-AM-T ANODE ANODE UF00PKG BF-AMMO SA09-O CATHODE CATHODE STV979 ANODE 7 6 E C B 9

28 -. IC BLOCK DIAGRAMS A BOARD IC0 STV A BOARD IC0 TDA79 VOLUME 7 - POWER AMPLIFIER + FLYBACK GENERATOR THERMAL PROTECTION 0K VOLUME MUTE/STBY PROTECTIONS OP AMP 60K 9 0 0K OP AMP A BOARD IC0 TDA987/V TUNER AGC VIF AGC AFC DETECTOR VOLTAGE REFERENCE A BOARD IC606 STR-F66 VIF AMPLIFIER FPLL VCO TWO VIDEO DEMODULATOR AND AMPLIFIER 6 START REG O.V.P LATCH DRIVE SIF AMPLIFIER QSS MIXER INTERCARRIER MIXER AM DEMODULATOR 8 T.S.D Iconst O.S.C SIF AGC INTERCARRIER MODE SWITCH FM-PLL DEMODULATOR 9 0 A BOARD IC0 CXA060AS APC <HUE> ACO DET. CHROMA AMP BPF PAL.MHz NTSC.8MHz <C BPF> C VCO.69MHz.79MHz 9.808MHz PAL/NTSC DEMOD COLOR SYSTEM DISCRIMINATOR PAL ID <PAL/NTSC> <XTAL ID> PAL/NTSC COLOR KILLER <KILLER> SECAM ID <SECAM> <XTAL> <COL SYSTEM> <COL LOOP> <ID START> <ID STOP> <HUE> BELL FILTER (ZAP) ACC AMP ACC AMP ACC DET LIM AMP PLL SECAM FM DEMOD FILTER ALIGNMENT LINE BLK DE- EMPHASIS SECAM VCO CAL. by.mhz SW NTSC PAL,SECAM KILLER <KILLER OFF> H DELAY LINE (PAL/SECAM) DPIC <DPIC> <AGING> CLAMP DC TRAN <DC TRAN> EYUV CLAMP YUV SW <Y SEL> YUV OUT <C DECOD> COLOR AMP <COLOR> <C DFF> AXIS <COL MATRIX> Y/C MIX RGB CLAMP VPROT <VNG> VM AMP (OFF YS/YM) CLAMP RGB / YS SW <RGB SEL> YM SW Y SW DYNAMIC COLOR <DY COL> ABL/PEAK LIM <ABL MODE> <ABL VTH> PICTURE AMP <PICTURE> GAMMA AMP <GAMMA> DAC SW CLAMP BRIGHT CONT <BRIGHT> DRIVE AMP <R/G/B DRIVE> CUTOFF CONT <R/G/B CUTOFF> AKB <IKR> PC BUS DECODER STATUS I/T R/G/B BLK <PON> <RGB ON> 7 CHROMA SW Y SW MONITOR SW VIDEO SW ATT V SYNC SEP <VSS> <VSS LPF> TRAP PAL.MHz NTSC.8MHz SECAM. -.MHz <TRAP OFF> COUNT DOWN <FIELD FREQ> <CD MODE> <INTERLACE> LINE COUNTER V TIM GEN <UNDER SCAN> <FIELD ID> DL PAL/NTSC 00 x 00nS SECAM 00 x 00nS <Y DELAY> SHARPNESS DL SHARPNESS AMP <SHARPNESS> <SHP FO> <PREOVER> V SAW GEN (0/0) VTIM WIDE SAW FUNC <ASPECT> <SCROLL> <UPPER VLIN> <LOWER VLIN> <V ZOOM> <V UNDER SCAN> VD SAW FUNC <VON> <S CORRECTION> <VSIZE> <V LINEARITY> <V POSITION> <EHT COMP> EW PARABOLA FUNC <H SIZE> <TRAPEZIUM> <PIN AMP> <EW DC> <CORNER PIN> 9 6 <VIDEO SEL> <S SEL> H SYNC SEP <HSS> AFC <APC GAIN> <FH HIGH> <H CENT> H SAW GEN H OSC <ZAP> H TIM GEN <H BLK> <LEFT HBLK> <RIGHT HBLK> PHASE DET <H POSITION> <AFC BOW> <AFC ANGLE> HPROT <HNG> HD GEN <HD W> IREF REG

29 SECTION 7 ELECTRICAL PARTS LIST Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. RESISTORS All resistors are in ohms. F : nonflammable. When indicating parts by reference number, please include the board name. CAPACITORS MF : mf, PF : mmf COILS MMH : mh, uh A REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK *A-6-8-A A BOARD, COMPLETE (KV-MD) ***************** *A A A BOARD, COMPLETE (KV-MK) ***************** *A-6-8-A A BOARD, COMPLETE (KV-TD) ***************** *A-6-8-A A BOARD, COMPLETE (KV-TK) ***************** *A-6-80-A A BOARD, COMPLETE (KV-TR) ***************** HOLDER, LED SCREW (MX8), P, SW (+) SCREW (MX0), P, SW (+) < CAPACITOR > C ELECT 00MF 0% V C ELECT MF 0% 0V C CERAMIC CHIP 0.MF V C CERAMIC CHIP PF % 0V C CERAMIC CHIP PF % 0V C ELECT 70MF 0% 6V C ELECT 0MF 0% 0V C ELECT MF 0% 0V C ELECT MF 0% 0V C ELECT 0.7MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.MF 0% V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.MF V C ELECT 70MF 0% 6V C ELECT 00MF 0% V C ELECT 7MF 0% 0V C CERAMIC CHIP 0.MF 0% V C ELECT 70MF 0% 6.V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.MF 0% V C CERAMIC CHIP 0.MF 0% V C0-6-- CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C ELECT 0MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0PF 0% 0V C CERAMIC CHIP 0.00MF 0% 0V C ELECT 00MF 0% 6V C ELECT 70MF 0% 6V C CERAMIC CHIP 0.09MF 0% 0V C CERAMIC CHIP 0.09MF 0% 0V C ELECT 00MF 0% V C ELECT MF 0% 0V C CERAMIC CHIP 00PF % 0V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 9PF 0.PF 0V C CERAMIC CHIP 0.MF 0% V C CERAMIC CHIP 0.MF V C SHORT 0 C CERAMIC CHIP PF % 0V C ELECT MF 0% 0V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.MF 0% 6V C ELECT.MF 0% 0V C ELECT.MF 0% 0V C CERAMIC CHIP 0.MF V C CERAMIC CHIP 0.00MF 0% 0V C CERAMIC CHIP 0.0MF 0V C CERAMIC CHIP PF % 0V C CERAMIC CHIP 0.7MF 6V C CERAMIC CHIP 0.7MF 6V C ELECT 7MF 0% 6V C CERAMIC CHIP 0.7MF 6V C CERAMIC CHIP 0.MF V

30 A The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK C -8-- ELECT MF 0% V C CERAMIC CHIP 0.MF 0% V C CERAMIC CHIP 0.MF 0V C CERAMIC CHIP 0.0MF 0V C CERAMIC CHIP 0.0MF 0V C CERAMIC CHIP PF % 0V C ELECT 7MF 0% 6V C ELECT 7MF 0% V C CERAMIC CHIP 0.0MF 0V C CERAMIC CHIP 0.007MF 0% 0V C ELECT 0MF 0% V C ELECT 000MF 0% V C ELECT MF 0% 0V C ELECT 000MF 0% 0V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.00MF 0% 0V C CERAMIC CHIP 0.00MF 0% 0V C CERAMIC CHIP MF 0% 0V C CERAMIC CHIP 0.MF 0% V C CERAMIC CHIP 0.MF V C ELECT 7MF 0% 6V C CERAMIC 0.0MF 0V C ELECT 0MF 0% 0V C CERAMIC CHIP 70PF 0% 0V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.MF 0% V C ELECT.7MF 0% 0V C CERAMIC CHIP 8PF % 0V C CERAMIC CHIP 8PF % 0V C CERAMIC CHIP 0.MF V C CERAMIC CHIP 0PF % 0V C FILM 0.MF % 0V C ELECT 0MF 0% 0V C ELECT.7MF 0% 0V C CERAMIC CHIP 0.MF 0% V C ELECT 7MF 0% V C9-6-- CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.MF V C -6-- CERAMIC CHIP 0.0MF 0% 0V C -6-- CERAMIC CHIP 0.0MF 0% 0V C ELECT MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C -6-- CERAMIC CHIP 0.0MF 0% 0V C6-6-- CERAMIC CHIP 0.0MF 0% 0V C7-6-- CERAMIC CHIP 0.0MF 0% 0V C ELECT 7MF 0% 0V C CERAMIC CHIP 0.MF V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.00MF % 0V C ELECT MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C CERAMIC CHIP 0.00MF % 0V C ELECT MF 0% 0V C ELECT 0MF 0% 0V C ELECT 0MF 0% 0V C ELECT 0MF 0% 0V C CERAMIC CHIP 0.00MF 0% 0V C LEAD, JUMPER (.0MM) C CERAMIC CHIP 0.00MF % 0V C ELECT 70MF 0% 6V C ELECT MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C ELECT 00MF 0% 0V C CERAMIC CHIP 0.MF V C ELECT 00MF 0% 0V C MYLAR 0.MF 0% 00V C FILM 0.7MF % 0V C CERAMIC CHIP 0.0MF 0% 0V C ELECT 00MF 0% 6V C ELECT MF 0% 0V C MYLAR 0.0MF 0% 00V C CERAMIC CHIP 70PF 0% 0V C ELECT MF 0% 0V C ELECT 0MF 0% V C ELECT 0MF 0% V C MYLAR 0.0MF 99% 00V C CERAMIC CHIP 0.00MF % 0V C CERAMIC CHIP 0.MF V C ELECT 0MF 0% 0V C -6-- CERAMIC CHIP 0.0MF 0% 0V C -6-- CERAMIC CHIP 00PF % 0V C FILM 0.68MF % 00V C MYLAR 0.007MF 0% 00V C CERAMIC CHIP 0.MF 0V C ELECT.MF 0% 00V C MYLAR 0.07MF 0% 00V C CERAMIC 680PF 0% KV C -6-- CERAMIC 70PF 0% KV C ELECT MF 0% 0V C FILM 0.09MF % 00V C7 --- FILM MF % 00V C8-6-- CERAMIC 70PF 0% KV C ELECT MF 0% 60V

31 The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK A C CERAMIC 80PF 0% 00V C MYLAR 0.007MF 0% 00V C FILM 0000PF %.KV C ELECT MF 60V C ELECT 00MF 0% 0V C CERAMIC CHIP 0.0MF 0% 0V C CERAMIC CHIP 0.007MF 0% 0V C ELECT.7MF 0% 0V C FILM 0.MF 0% 00V C FILM 0.MF 0% 00V C CERAMIC 0.00MF 99% 0V C CERAMIC 0.00MF 99% 0V C ELECT 70MF 0% 0V C ELECT(BLOCK) 0MF 0% 00V (KV-MD/MD/MK/TK) ELECT(BLOCK) 0MF 0% 0V (KV-TR) C CERAMIC 0.00MF 0% KV C ELECT 00MF 0% 0V C ELECT 00MF 0% V C CERAMIC 70PF 0% 00V C CERAMIC 0.007MF 0V C CERAMIC 0.007MF 0V C CERAMIC 0.007MF 0V C FILM 0.0MF 0% 00V C ELECT 00MF 0% V C CERAMIC CHIP 70PF 0% 0V C CERAMIC 0.007MF 0V C ELECT 00MF 0% V C ELECT 00MF 0% V C ELECT 00MF 0% 60V C FILM 0.MF 0% 0V C CERAMIC 70PF 0% 00V C6-0-- CERAMIC 70PF 0% KV C ELECT MF 0% 60V C ELECT 0MF 0% 00V (KV-MD/TD) ELECT 0MF 0% 0V (KV-MK/TK/TR) CF TRAP, CERAMIC (6.MHZ) (KV-MK/TK/TR) SWF FILTER, SURFACE WAVE (KV-MD/TD) FILTER, SAWTOOTH WAVE (KV-MK/TK/TR) CN00 CN0 CN0 CN0 CN06 < CONNECTOR > * PLUG, CONNECTOR P * PLUG, CONNECTOR P * CONNECTOR PIN (DY) * PLUG, CONNECTOR 6P TAB (CONTACT) CN08 * PLUG, CONNECTOR P CN60 * PIN, CONNECTOR (POWER) CN PIN, CONNECTOR (MM PITCH) P CN PIN, CONNECTOR (MM PITCH) P D00 D00 D00 D00 D00 D007 D008 D009 D00 D0 D0 D0 D0 D07 D08 < DIODE > DIODE RD.6ESB DIODE RD.6ESB DIODE LS60HL DIODE RD.6ESB DIODE RD.6ESB DIODE RD.6ESB DIODE SST DIODE RD.6ESB DIODE RD.6ESB DIODE RD.6ESB DIODE DAN0K DIODE RB0V-0TE DIODE DAN0K DIODE RD.6ESB DIODE SST-77 D DIODE RD.6ESB D DIODE UPC7J D DIODE DAN0K (KV-MK/TK/TR) D DIODE HZS9.NB D DIODE DAN0K C ELECT 00MF 0% V C ELECT 7MF 0% V C ELECT 00MF 0% V C ELECT 00MF 0% V < FILTER > CF TRAP, CERAMIC CF FILTER, CERAMIC (KV-MK/TK/TR) CF FILTER, CERAMIC D0 D0 D06 D06 D07 D08 D0 D0 D DIODE RD.6ESB DIODE RD.6ESB DIODE RD.6ESB DIODE RD.6ESB DIODE RD.6ESB DIODE RD.9ES-B DIODE HZS9.NB DOIDE RD.6ESB DIODE RD6.8ES-B

32 A The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK D06 D07 D08 D D0 D D D0 D0 D0 D D D D D6 D9 D D7 D7 D60 D60 D60 D60 D608 D60 D6 D69 D6 D66 D DIODE RD6.8ES-B DIODE RD6.8ES-B DIODE HZS9.NB DIODE RD6.8ES-B DIODE RD6.8ES-B DIODE RD6.8ES-B DIODE HZS9.NB DIODE RD6.8ES-B DIODE GP08D DIODE MTZJ-T-77-B DIODE GP08D DIODE GP08D DIODE GP08D DIODE GP08D DIODE ERC06-S DIODE ERD8-08S LEAD, JUMPER (.0MM) DIODE SS DIODE MTZJ-.7C DIODE DSB60L DIODE AU-0Z-V DIODE AU-0Z-V DIODE RUAM-T DIODE RGCLF-B DIODE RNZ DIODE SS DIODE AK0VO DIODE ERC0-06SE DIODE ERC0-06SE DIODE SLA0F FB FERRITE 0UH FB FERRITE 0.UH FB FERRITE.UH FB FERRITE.UH FB LEAD, JUMPER (.0MM) < IC > IC IC SAA9PS/MA/088 (KV-MD/MK) IC SAA98PS/MA/08 (KV-TD) IC SAA98PS/MA/079 (KV-TK) IC SAA98PS/MA/080 (KV-TR) IC HYB IC SBX98- IC00 IC00 IC0 IC0 IC0 IC0 IC IC60 IC60 IC60 IC606 IC608 IC IC MN8-T(TA) IC STW08FM6TR IC TDA987/V IC TDA IC CXA060BS IC STV IC LM9N IC SEN IC TYA780CTV IC LM90T IC STR-F IC TYA780CTV IC TOP09P < PHOTO COUPLER > PH PHOTO COUPLER PCF < SOCKET > D68 D69 D6 D6 D DIODE P6KE00AG DIODE UF00PKG DIODE RDES-B DIODE SLA0F DIODE RD.6ESB J0 J0 J JACK CONNECTOR (SQUARE TYPE) P JACK, PIN P < COIL > D DIODE RNZ < FUSE > F FUSE (H.B.C.) AMP 0V *--7- HOLDER, FUSE (F60) < FERRITE BEAD > FB FERRITE 0UH FB FERRITE 0UH FB FERRITE 0UH FB FERRITE 0UH FB FERRITE.UH L INDUCTOR 0UH L INDUCTOR 8.UH L COIL L LEAD, JUMPER (.0MM) L INDUCTOR 7UH L INDUCTOR UH L INDUCTOR 7UH L INDUCTOR UH L INDUCTOR 0UH L INDUCTOR 0UH L INDUCTOR 0UH L SHORT 0 6