7/8" BOR LENGTH - 1-3/4 IN MOR LENGTH MOR LENGTH PER SUBMISSION. Example of continuous row

Size: px

Start display at page:

Download "7/8" BOR LENGTH - 1-3/4 IN MOR LENGTH MOR LENGTH PER SUBMISSION. Example of continuous row"

Alisha Berry
5 years ago
Views:

1 AMELUX Lin1.5 Mini Direct/Indirect LED (emote Driver) SHEET #: (1 of 7) SPEC. SHEET EFEENCE: WANING - ISK OF FIE AND ELECTICAL SHOCK. FIXTUE MUST BE INSTALLED BY A QUALIFIED ELECTICIAN ONLY. FIXTUE IS INTENDED FO INSTALLATION IN ACCODANCE WITH THE NATIONAL ELECTICAL CODE, LOCAL AND FEDEAL SPECIFICATIONS. DISCONNECT POWE AT ELECTICAL PANEL BEFOE SEVICING. ETAIN THESE INSTUCTIONS FO MAINTENANCE EFEENCE. Suspension Points for fixtures are: CAUTION: Maximum distance between suspension point in Lin1.5MDI cannot exceed 8' 7/8" INDIVIDUAL LENGTH - 1-3/4 IN 7/8" 7/8" BO LENGTH - 1-3/4 IN MO LENGTH EO LENGTH 7/8" BO LENGTH PE SUBMISSION INDIVIDUAL LENGTH PE SUBMISSION MO LENGTH PE SUBMISSION Example of continuous row Individual EO LENGTH PE SUBMISSION efer to general contractor/ electrician layout for proper location of mounting points/ locations for junction boxes. 1. Install junction box(es) - The junction box should be regressed as shown to make sure that the canopy cover sits flush with the ceiling when install is finished. 2. Single Feed emote Driver 1. Turn off power at panel. 2. In an accessible location, secure remote Driver Enclosure to within 5' of J Box above fixture. 3. Connect AC power supply to driver according to National and Local electrical codes. Note: Driver Enclosure is pre-wired with 5' of plenum rated cord. 4. Fixture is pre-wired at factory with 10' of cord. un cord from fixture to J-Box above. Measure, cut, and strip for final connection in J Box above fixture. see page 2 for details. Note: The driver box must be placed in an accessible area. SHIELDED CABLE(18/2 PVC) POVIDED OFF BOX: 5' POWE CANOPY TOTAL FIXTUE LENGTH PE : 5W MIN: 2'-0" 10W MIN: 2'-0" SEE JOB DOCUMENTATION (LTP DAWING) FO LOCATION(S) OF S AND COESPONDING FIXTUES EMOTE ENCLOSUE CEILING STANDAD J-BOX (BY OTHES) SHIELDED CABLE(18/2 AWM) POVIDED OFF FIXTUE: 10' TOTAL CABLE LENGTH FOM TO FIXTUE CANNOT EXCEED 25' (INSTALLING CONTACTO TO CUT/STIP POVIDED LEADS TO MEET THIS CITEIA) BO MO EO

2 AMELUX SHEET #: (2 of 7) 3. Individual and Beginning of un (Bo) Install: COUNTESUNK 1 4"-20 GEM BA NON- COUNTESUNK 1 4"-20 GEM BA 5" Feed Canopy Junction Box Strain elief Bushing Feed ON-CENTE LGTH PE ABOVE Canopy Power Cord Tie (1 per foot) Black SJT ed/harness Purple DIM (+) 18/2 SJT WIING CONNECTIONS In J-Box 1. At feed of Bo, thread cable through 5" Canopy (with 2nd hole) & coupler. Insert into (see. 2. At non-feed of Bo, thread through 5" Canopy &. Insert into (see. 3. Level fixture by adjusting cable at fixture. 4. un cord from fixture to J Box. Cut, and strip for final connections in J Box above fixture. See #4 page 1 Feed (Bor) and (Individual) Bo (feed ) IND BO MAKE SUE TO DISCONNECT ALL ELECTICAL CONNECTIONS BEFOE ACCESSING LED.

3 AMELUX 4. Assembling Continuous ows: SHEET #: (3 of 7) a. Hang Mo/Eo: Hang Mo/Eo as shown on page 2, Bo should be self supporting. Hang feed hanger on far of Mo/Eo, swing up to join on non Feed of Bo 2) BO Continuing ow b. Bo to Mo/Eo: After hanging one of the Mo/ Eo's on far feed, swing unit up and join to Bo by aligning pins of Feed s of Bo to plain of the Mo or Eo (no cable) push together. Make sure surfaces line up before using catch & latch. Single hanger on Mo/Eo (Eo shown here). Typically with feed. Hang to suspension cable as d e t a i l e d i n I t e m 2. Mo/Eo Joining the Housings Line up the two housings by using the alignment pins and light leak shields. Secure them together by using the System on the top of the extrusion. Bo c. Mo to Mo/Eo: After hanging one, (far feed ) of Mo/Eo, swing unit up and join to Mo by aligning pins and push together. Make sure surfaces line up before using catch & latch. Continue adding Mo's and finish un with (possibly odd length) Eo, with End Cap. d. Secure fixtures/joint: Mo/Eo Mo Alignment pins and light sheilds MAKE SUE TO DISCONNECT ALL ELECTICAL CONNECTIONS BEFOE ACCESSING LED.

4 AMELUX Lin1.5 Mini Direct/Indirect LED (emote Driver) SHEET #: (4 of 7) SPEC. SHEET EFEENCE: WANING - ISK OF FIE AND ELECTICAL SHOCK. FIXTUE MUST BE INSTALLED BY A QUALIFIED ELECTICIAN ONLY. FIXTUE IS INTENDED FO INSTALLATION IN ACCODANCE WITH THE NATIONAL ELECTICAL CODE, LOCAL AND FEDEAL SPECIFICATIONS. DISCONNECT POWE AT ELECTICAL PANEL BEFOE SEVICING. ETAIN THESE INSTUCTIONS FO MAINTENANCE EFEENCE. Suspension Points for fixtures are: CAUTION: Maximum distance between suspension point in Lin1.5MDI cannot exceed 8' 7/8" INDIVIDUAL LENGTH - 1-3/4 IN 7/8" 7/8" BO LENGTH - 1-3/4 IN MO LENGTH EO LENGTH 7/8" BO LENGTH PE SUBMISSION INDIVIDUAL LENGTH PE SUBMISSION Individual MO LENGTH PE SUBMISSION Example of continuous row EO LENGTH PE SUBMISSION efer to general contractor/ electrician layout for proper location of mounting points/ locations for junction boxes. 1. Install junction box(es) - The junction box should be regressed as shown to make sure that the canopy cover sits flush with the ceiling when install is finished. 2. Duel Feed emote Driver 1. Turn off power at panel. 2. In an accessible location, secure remote Driver Enclosure to within 5' of J Box above fixture. 3. Connect AC power supply to driver according to National and Local electrical codes. Note: Driver Enclosure is pre-wired with 5' of plenum rated cord. Wires labeled as circuit 1 and circuit Fixture is pre-wired at factory with 10' of cord. un cord from fixture to J-Box above. Measure, cut, and strip for final connection in J Box above fixture. see page 5 for details. Note: The driver box must be placed in an accessible area. SHIELDED CABLE(18/2 PVC) POVIDED OFF BOX: 5' POWE CANOPY TOTAL FIXTUE LENGTH PE : 5W MIN: 2'-0" 10W MIN: 2'-0" SEE JOB DOCUMENTATION (LTP DAWING) FO LOCATION(S) OF S AND COESPONDING FIXTUES EMOTE ENCLOSUE CEILING TOTAL CABLE LENGTH FOM TO FIXTUE CANNOT EXCEED 25' (INSTALLING CONTACTO TO CUT/STIP POVIDED LEADS TO MEET THIS CITEIA) STANDAD J-BOX (BY OTHES) SHIELDED CABLE(18/2 AWM) POVIDED OFF FIXTUE: 10' BO MO EO

5 (5 of 7) 4. Duel Feed Individual and Beginning of un (Bo) Install: COUNTESUNK 1 4"-20 GEM BA AMELUX SHEET #: NON- COUNTESUNK 1 4"-20 GEM BA 5" Feed Canopy Junction Box Strain elief Bushing Feed ON-CENTE LGTH PE ABOVE Canopy Power Cord Tie (1 per foot) SJT ed/harness Purple DIM (+) Black 18/2 SJT WIING CONNECTIONS In J-Box 1. At feed of Bo, thread cable through 5" Canopy (with 2nd hole) & coupler. Insert into (see. 2. At non-feed of Bo, thread through 5" Canopy &. Insert into (see. 3. Level fixture by adjusting cable at fixture. 4. un cord from fixture to J Box. Cut, and strip for final connections in J Box above fixture. See #4 page 4 Feed (Bor) and (Individual) Bo (feed ) IND BO MAKE SUE TO DISCONNECT ALL ELECTICAL CONNECTIONS BEFOE ACCESSING LED.

6 AMELUX 4.Duel Feed Assembling Continuous ows: SHEET #: (6 of 7) a. Hang Mo/Eo: Hang Mo/Eo as shown on page 2, Bo should be self supporting. Hang feed hanger on far of Mo/Eo, swing up to join on non Feed of Bo 2) BO Continuing ow b. Bo to Mo/Eo: After hanging one of the Mo/ Eo's on far feed, swing unit up and join to Bo by aligning pins of Feed s of Bo to plain of the Mo or Eo (no cable) push together. Make sure surfaces line up before using catch & latch. Single hanger on Mo/Eo (Eo shown here). Typically with feed. Hang to suspension cable as d e t a i l e d i n I t e m 2. Mo/Eo Joining the Housings Line up the two housings by using the alignment pins and light leak shields. Secure them together by using the System on the top of the extrusion. d. Secure fixtures/joint: Bo c. Mo to Mo/Eo: After hanging one, (far feed ) of Mo/Eo, swing unit up and join to Mo by aligning pins and push together. Make sure surfaces line up before using catch & latch. Continue adding Mo's and finish un with (possibly odd length) Eo, with End Cap. Mo/Eo Mo Alignment pins and light sheilds MAKE SUE TO DISCONNECT ALL ELECTICAL CONNECTIONS BEFOE ACCESSING LED.

7 AMELUX SHEET #: (7 of 7) Maintenance: For LED replacement Snap-in Lens eflector eflector snap spring WANING: Electrostatic and polarity sensitive device. Use caution while handling and wiring. 1.) LED Fixture: Consult Amerlux for LED maintenance. 2.) LED eplacement: For LED board replacement reference Instruction Sheet eflector #6-32 self-tap screws AMX P/N (4) per reflector Snap-in Lens MAKE SUE TO DISCONNECT ALL ELECTICAL CONNECTIONS BEFOE ACCESSING LED.

RKDISE LED. LED Center Basket Retrofit Kit EXAMPLE: RKDISE24-LED48FRDMV WATT CAT# APPLICATIONS FEATURES & BENEFITS

RKDISE LED. LED Center Basket Retrofit Kit EXAMPLE: RKDISE24-LED48FRDMV WATT CAT# APPLICATIONS FEATURES & BENEFITS RKDISE LED LED Center Basket Retrofit Kit APPLICATIONS This unique LED Retrofit Kits is an energy efficient, easy to install solution to upgrade your fluorescent troffer to LED. Compatible with both standard