DF-3500 DF Before operating the unit, please read this manual thoroughly and retain it for future reference

Transcription

1 Colour TFT LCD 12/24Volt Vehicle Wireless Rear View System Installation/User Guide DF-3500 DF-5500 Before operating the unit, please read this manual thoroughly and retain it for future reference

2 1. TFT LCD MONITOR 7. ENCLOSURE 1-1. Appearance Electrical & Hardware Accessories: Power indicator Color LCD screen Power ON/OFF Volume increase,analog quantity selection + Volume increase,analog quantity selection - Menu Automobile power supply adapter B/D/A/V conversion line Earphone Remote controller Down AV1/AV2 shift Display base support Earphone Jack Rewmote receiving window Support Spacer Car lighter 1-2. Technical Parameters WARRANTY Product: TFT LCD Color Monitor Display Device: Color TFT-LCD Screen Size: 5 inches Audio Output: 200MW Loudspeaker: 4.0cm round loudspeaker Connecting Terminal: Earphone jack, external power supply input jack, 6 Pin Mini pin connector (Av1, AV2,Power,Audio,round Input.) Power Consumption: about 8W Dot Pitch: (H) (V) Resolution: 960 (H) 234 (V) Viewing Angle: U: 15 / D: 35, R/L: 50 Brightness: 300cd/m2. Contrast: 150:1 Weight: 430g Outer Dimension: W 163mm H 125mm T 30.5mm Veise Electronics warrant to the purchaser that the product described herein is free from defects in the normal or wordman ship under normal use for 1 year from date of purchase.during the warranty peirod,upon proof of purchase,veise Electronics will either repair or replace the product without charge for either parts or labour. The purchaser shall pay all posting and insurance costs to Veise Electronics and Veise Electronics shall pay all the retun posting and insurance costs. This warranty does not cover damage resulting from negligence of the precautions in the Wiring &Operation instructions,alterations performed by unauthorized persons and abuse. The warranties set forth herein are made in lieu of any other warranties,including implied warranty of merchantability and / or fitness for purposes. This warranty does not affect your rights under statutory law. 1 14

3 Field of View:130 Please Please mount mount the the CAM CAM 1 1 on on the the back back of of the the vehick vehick and and connect connect it it with with the the CAM CAM 1 1 jack jack of of the the switch switch box box DF-3500 (DF-4103W+SP-M50+Box) DF-3500 (DF-4103W*2+SP-M50+Box) CAM1 NC Signal of reversing bulb/swith(brown) Poewer input lead(red) Ground lead(black) B/D/A/V OUT A V 1 IN CAM2 Connect to Vehicle power 6. 3.BOX CONNECTION SCHEMATIC DRAWING 1. TFT LCD MONITOR 1-3. OPERATION MANUAL Notice: For one camera system Please leave the switch off, It helps to save power and to maintain the system 1. POWER Button Simply press this button to turn Monitor ON/OFF. ANT ANT ANT 2. AV1/AV2 Shift Button Use this button to select required Video Input. As you press this button the screen displays the selected video input source. AUDIO (Red) VIDEO (Yellow) 3. VOL-and VOL+ Buttons These buttons have dual operations,they are used to control the audio volume and also used to increment / decrement values when system is in MENU mode. 4. DOWN Button Use this button to shift down Options whilst in MENU mode. This enables you to select specific options for adjustment. 5. MENU Button Pressing this button selects one of Four Menu modes. These modes are as follows: 5! Warning 1.For the sake of safety for yourself and others, please do not watch or turn on the display during driving. 2.It is dangerous to watch or operate TV while driving. 13 2

4 1. TFT LCD MONITOR 5. BASIC OPERATION METHODS 1-4. Menu Operation To enter MENU mode simply press the MENU button. Each time you press the MENU button the screen will display one of four adjustable modes,these menu modes are Picture, System, Options and Clock. (1) Picture ON(Manual) Power box ON/OFF Switch OFF(Auto) Contrast, bright, color and sharp displays on the screen as illustrated below: Power Switch For LCD Picture Contrast 80 Bright 80 Color 60 Sharp 50 Display LCD A V 1 State Display LCD A V 2 State Switch for CAM 1/ CAM 2 Input VCD/DVD /TV Signal Switch for CAM 1 Switch for CAM 2 Down VOL + / VOL - : Switch CAM 1 Signal Switch CAM 2 Signel Use the DOWN button to scroll down the lost to the required Option For example we are going to select the Contrast option. Now use the Vol- and Vol+ buttons to alter the Contrast value that is displayed to the right hand side of the screen (Min setting = 0, Max setting = 100). You will see the screen contrast change as you alter the value. Values for Brightness, Colour and Sharpness can also be changed using above example. TFT Shows the Picture! Display CAM 1 Picture Display CAM 2 Picture When the drive selects reverse gear the reversing light receive a switched +12V/24V to the positive side of the bulbs, The momitor Auto display mirror piclture of rear view CAM1 Wireless equip ment is disturbed easily by the frequency change of outside ambient 3 12

5 4. 3.BOX POWER CONTROLED BY SWITCHING BOX 4-1. Appearance ANT TFT LCD MONITOR (2) System Input, Color System and Language displays on the screen as illustrated below: 1 Ground (black) Press Down select the item Input: 39mm 2 3 DC 12~32V Power (red) Backward IN (brown) System VIDEO IN AUDIO IN A V 1 120mm POWER IN NC (white) Input Color System Language AV AUTO Chinese B/DC/A/V OUT DC 12/32V ON/OFF CAM1/CAM2 B/DC/A/V OUT PL 4-2. Basic operation methods POWER CONNECTIONS There are four wires (Red,Black,Brawn and White) to the power switch module. The wires have the following functions: RED WIRE (15 Amp Fused) Connect this wire to a common +12 V or +24 V source. BLACK WIRE Connect this wire to a common negative chassis point that is clean and free from rust. BROWN WIRE This wire must be connected to the positive side of the reversing bulbs or a switched positive output from the reverse gear switch wire.when the driver selects reverse gear the reversing lights receive a switched +12/24 V to the positive side of the bulbs,which supplies voltage to the brown wire and activates the monitor for reverse camera viewing. WHITE WIKE A pre-fitted power connector please leoeve it your do not use it Receiving Frequency:ISM 2,400~2,483MHZ Power Consumption:12W Audio 1 OUT Video 1 OUT Backward OUT Video 2 OUT Ground DC 12V OUT Down VOL + / VOL - : Then press VOL- or VOL + to shift the picture from AV1 to Av2. Press Down to select the item Color System System Input Color System Language Down Then press VOL - or VOL+ to revolve the screen in order of AUTO, PAL,N3.58 and N4.43. Please choose carefully the correct system, otherwise,it may cause achromatic or inferior color. It is recommended to select on AUTO position. 4 AV AUTO Chinese VOL + / VOL - :

6 80mm 1. TFT LCD MONITOR Press Down to select the item Language: 3. COLOR CCD CAMERA 3-1. Appearance System Input Color System Language AV AUTO Chinese 75mm 3-2. Technical Parameters 70mm Down VOL + / VOL - : Press VOL -/ VOL + can realize switch between Chinese,English, Russian,Arabic and German menu.! Notice If earphone is applied,the sound only transmits through the earphone,no sound from the monitor Camera: Image sensor: Lens: Resolution: Minimum illumination: Video Output: Power Consumption: 2.9~3.6mm(Board) 380 TV line S/N Ratio: 48dB(AGC Off) Gamma Characteristic: 0.45 Internal Synchronization: IR project distance: Transmit Frequency: Antenna: Output frequency Water resistance: Camera & Bracket weight Operating temperature: High Resolution Color CCD Sync System 0Lux (IR LED ON) 1.0Vp-p 75 ohm 15 meters ISM 2,400~2,483MHZ 50ohm SMA 10mW Ip W 350g -10 ~+50 Wide range voltage input: DC 12~24V alloyed shell and built in IR LED night vision illuminators The new compact and waterproof designed for out door usage 5 10

7 2. MONITOR REMOTE CONTROL POWER (Power switch) Press this button is to turn off the monitor, press it again is to turn on the machine. Press this button in game status is to exit game. CH button(up/down) press this button to select MENU mode. See MENU MODE OPERATION for operational details of this feature. VOL - / + (Volume adjust): Press VOL -,the volume of Display decreases. Press VOL +,the volume of Display increases. Menu Press this button to select MENU mode. See MENU MODE OPERATION for operational details of this feature MODE (Mode) Press this button, users can realize the five picture statuses of Standard,Soft, Vivid, light and Personal. CALL (Call) Press this button is to display AV character currently watching. TIMER Time setup of sleep off, it is used to set the time off within 120 minutes. C / E / P (Language) Press this button can realize the switch of Chinese, English, Russian, Arabic and German menu. CALE Press this button is to show Year, Month, Day and Week. Press CH - / CH + is to adjust the Year, press VOL - / VOL + is to adjust the Month. VIDEO (AV1 / AV2 shift) Press this button is to realize switch between AV1 and AV2 pictures. 1. TFT LCD MONITOR (3) Option horizontal and vertical modes will display on the screen as illustrated below: Press Down to choose the item Horizontal: Option Horizontal Vertical Down VOL + / VOL - : Press VOL- / VOL+ can realize Horizontal, press again is to resume the picture. Press Down to choose the item Vertical Option Horizontal Vertical Press this button is to flip the picture horizontally. Press this button is to flip the picture vertically. Down VOL + / VOL - : Press VOL-/VOL+ can realize Vertical, and press again is to resume the picture. 9 6

8 1. TFT LCD MONITOR 2. MONITOR REMOTE CONTROL (4) Clock Clock, ON Time, OFF Time, Attention, CH- Time will display on the screen as illustrated below: Clock 2-1. Appearance Mute MUTE CH Power Swtch Exit Game Time --:-- ON Time --:-- OFF Time --:-- Attention --:-- CH-Time --:-- Channel ion Volume Picture Mode Language CH VOL- VOL+ MENU MODE CALL TIMER C/E/R/P/G CALE AV1/AV2 Menu Call Timer AV1/AV2 shift Press VOL-/VOL+ to set up clock, then press the Down to scvoll down the list to the required Option Flip horizontal Calendar Flip vertical VOL-: hour VOL+: minute Down: items to be setup ment of other items is the same as that of clock, setup of clock for all items is 24 hours at the most. Upon setup of clock, press Down to choose Option Time, upon setup, press Down again to choose ON Time and OFF Time, and press VOL-/VOL+ to adjust the time for time ON/OFF.! Special Notice Special notice a few highlights or dark spots may occur on the LCD screen.it is a very common phenomenon to the active matrix display technology, and never necessary means any defects or faults, Never try to repair this machine by yourself. In case of any fault or failure,please turn off the display at once,and notify our company or the corresponding dealer. The monitor is made up of many precision electronic components Any disassembly or modification may lead to damage or broken 7! Notice 1.Please align the remote controller with the infrared-receiving Window on display in operation. 2.Never oppress,drop,wet or disassembly the remote controller. 3.Never press any button continuously and swiftly,operation interval is at least 2 seconds. 4.Press Power to turn on the machine before pressing VIDEO or selection of AV 1 and AV OPERATION MANUAL MUTE (Mute): Press this button, sound disappears, press it again or VOL+/ VOL- is to resume normal sound. 8