Yaesu FT-950 and FT-450D with KPA/KAT500 Power Combo
|
|
- Muriel Morgan
- 11 months ago
- Views:
Transcription
1 Yaesu FT-950 and FT-450D with KPA/KAT500 Power Combo The Yaesu FTdx1200, FT-450D and FT-950 series radio can be connected to the KAT/KPA500 combo using the Key signal available on the rear panel of the linear and tuner. On these Yaesu radios, the keying signal is called, EX GND. This will set the KPA/KAT500 combo up for what is called, Basic Mode operation. Here's that connection found on the Linear port of these radios: Model Connector pin out Menu settings to check Ft-950 FTdx1200 FT-450D Be sure to disable internal tuner. Connections to the KPA500 and KAT500 Then, you will make the following connections with the KPA500 and the KAT500. Please note that cable items #2 and #4 are included in the boxes with the KPA500 and KAT500. We have RF patch cables available (cable #1) if needed. An adapter cable from these rigs to the KAT500 (cable #3) will be available soon from Elecraft.
2 Note: Cable #5 is a special connection for the KAT500 to operate as an Icom remote tuner. It is not relevant for a Yaesu radio.
3 Set-Up Procedure for the KPX/KAT500 Combo Set up the KAT500 to interoperate with the KPA500. Please enter the KAT500 Utility and select the Configuration tab then click on the button to Optimize for KPA500.
4 Training the Tuner Overview We will be stepping through each band where you have an antenna connected to the KAT500, selecting the top, bottom and places in the middle of each band where you expect to operate. At each of these points, we will be causing the radio to emit a steady-state RF signal for the KAT500 to use while it executes a full tune cycle. Since the KAT500 is an Automatic Tuner, it will remember the settings it finds at each of the points in the band. This is referred to as 'Training the Tuner'. The following sequence assumes that the radio, KAT500 and, if appropriate, the KPA500 are installed as specified in the KAT500 Owner's Manual, shown above as Figure 1. Place the KPA500 into STBY mode while we train the tuner. Set up On the radio, please select RTTY mode and an RF output level of about 25 watts. On the KAT500, select the MAN mode. On the KAT500, Tap the ANT button to select the appropriate antenna. The ANT LED will light solidly indicating the antenna port selected. On the radio, select the appropriate band. Then, adjust VFO A to the lowest spot in that band where your antenna will work. We suggest you start with 160 meters and step through the bands up to 6 meters. For each VFO Setting perform the following to Train the KAT500: 1. Tap the MODE button so that MAN light is selected and is not flashing. 2. Next, Tap the TUNE button on the KAT500. The MAN light will now start to Flash. This indicates that the KAT500 is now awaiting the RF needed to execute a Full Tune Cycle. 3. On the radio, key the rig with the PTT button on your mic to cause the radio to go into transmit. The radio s TX light should come on to confirm it is transmitting. 4. While holding the PTT button in, the KAT500 will begin to clatter as it searches for a low SWR. This is called the Full Tune Cycle. 5. The clattering will stop once a low SWR is found and the KAT500 MAN light will now be solid. This indicates that the full tune cycle is complete and the results have been memorized. a. Note that the tuner may not find a 1:1 SWR, which is normal. As long as the MAN light goes out, it has found a low SWR and has memorized the tune elements needed. 6. On the radio, adjust VFO A frequency for the upper end of the band where your antenna will operate. Repeat Steps 1-3 above for this setting. 7. Then, move into the middle of the band and repeat Steps 1-3 again.
5 8. These settings should give now have stored the tuning elements needed for those band ends and middle. 9. You may go through and add more tuning memories by selecting other portions of the bands where you tend to operate frequently. Train the tuner on all Bands Next, step to other bands where your antenna can operate within a 10:1 SWR ratio. Perform the same steps above as with the first band chosen. How do you know how many times per band needed to fully train the tuner? Here's the answer from the KAT500 Owner's Manual. Training the tuner with all of your antennas If you have more than one antenna, continue to ANT 2 and ANT 3 ports using the same technique above for those antennas. The KAT500 tuner can remember settings for all 3 antenna ports separately! Make it Easy for Your Tuner to Remember what it was Trained to Do Once you have fully trained your KAT500 tuner on all bands and all Antennas, you can save your work using the KAT500 Utility. Go to the Configuration tab in the Utility and select Save Configuration to complete your tuner's training.
6 MAN mode or AUTO mode? Unless you intend to operate the KAT500 in a remote configuration where it may be a long distance from where you will Control it, Elecraft recommends using MAN (Manual) mode. AUTO mode has an additional feature where the tuner will monitor SWR while you are transmitting. If, for some reason, the SWR rises above about 1.8:1 threshold (the default), AUTO mode will cause the KAT500 to enter Full Cycle Tune mode without you starting it. When used remotely, this is a very effective way of accommodating wide-ranging SWR due to weather or other conditions. Successful Full Cycle Tunes in AUTO mode will be memorized just as they are in MAN mode. AUTO mode thresholds can be set by the operator, too. Use the KAT500 Utility to enter the Configuration dialog and select Thresholds. There you can specify, by each ANT port, what level of upper and lower thresholds you want the AUTO mode feature to monitor. MAN mode will store successful Full Cycle Tunes just as AUTO mode will and the KAT500 will monitor SWR while you are transmitting. However, the KAT500 will not act if the SWR rises of falls. You can monitor it for yourself directly from the front of the KAT500 or from the KAT500 Utility.
Connecting the Elecraft Power Combo to the Kenwood TS-2000 series Transceiver
Connecting the Elecraft Power Combo to the Kenwood TS-2000 series Transceiver This Application Note describes how any model of the TS-2000 series transceiver can be connected the Elecraft Power Combo,
Panadapter for FT1000mp with a PMSDR and Hamradio deluxe Cat/ logging application
Panadapter for FT1000mp with a PMSDR and Hamradio deluxe Cat/ logging application Hardware and Software PMSDR (you don t need the switchboard plug- in!) FT1000mp Soundcard for the PMSDR (I use the EMU
PLUSTV 1680ex USER S MANUAL
PLUSTV 1680ex USER S MANUAL Ver 1.0 Contents 1. Instruction... 1 1.1 Functions and features... 1 1.2 Packaged contents... 2 1.3 Technical specifications... 3 2. Remote control instructions... 4 2.1 Diagram
USER MANUAL FOR CABLE RECEIVER KAON KCF-200CO KAON KCF-H220SCO
USER MANUAL FOR CABLE RECEIVER KAON KCF-200CO KAON KCF-H220SCO SECURITY INSTRUCTIONS FOR USING THE RECEIVER Always fallow these instructions to avoid risk of injury or damaging the equipment. Before cleaning
Automation Interface Requirements for J602 Basic I/O Interface of a DPC 4 Welding System
- 1 - Automation Interface Requirements for J602 Basic I/O Interface of a DPC 4 Welding System The DPC 4 welding system offers several features that are intended to communicate with automation. These features
MOTOTRBO. Tech Notes. Auto-Tuning MOTOTRBO Mobiles with the Aeroflex 8800SX. Technical Enablement Team. Place your image on top of this gray box.
Auto-Tuning MOTOTRBO Mobiles with the Aeroflex 8800SX MOTOTRBO Place your image on top of this gray box. Tech Notes If no graphic is applicable, MTN-13 delete gray box and notch-out behind gray box, from
Quick Tours. Quick Tour - The TiVo menus 2. Quick Tour - Watching live TV 5
Quick Tour - The TiVo menus 2 Quick Tour - Watching live TV 5 Quick Tour - The TiVo menus Your starting point TiVo Central TiVo Central is the starting point for just about everything you do with your
M5-H002. Multiview T-35. DVB-T to PAL / 5 channels on all TV s
120531 M5-H002 Multiview T-35 DVB-T to PAL / 5 channels on all TV s Contents Multiview... 3 Features... 3 Caution... 3 Front & Rear Panel... 4 Connecting... 5 Programming... 6 Information... 7 Installation...8
Receiver Customization
9241_13_Ch11_eng 10/30/08 3:16 PM Page 1 Receiver Customization PERSONALIZING YOUR SATELLITE RECEIVER Take a look through this chapter and you ll find out how to change settings on the receiver to make
LDG ALK-2 Two-Port Audio/Linear/Key Switch
ALK-2 OPERATIONS MANUAL MANUAL REV A LDG ALK-2 Two-Port Audio/Linear/Key Switch LDG Electronics 1445 Parran Road St. Leonard MD 20685-2903 USA Phone: 410-586-2177 Fax: 410-586-8475 ldg@ldgelectronics.com
InfiniTV 4 Installation Instructions
InfiniTV 4 Installation Instructions 1. Obtain a CableCARD from your cable TV service provider 1. Call your cable TV service provider and tell them you need a multi-stream CableCARD (M-Card) for a Ceton
PowerMaster II. Digital RF Power &VSWR Measurement System
PowerMaster II Digital RF Power &VSWR Measurement System Array Solutions 2611 N Belt Line Rd Sunnyvale, TX 75182 USA http://www.arraysolutions.com phone +1 214 954-7140 e-mail sales@arraysolutions.com
1 OVERVIEW 2 WHAT IS THE CORRECT TIME ANYWAY? Application Note 3 Transmitting Time of Day using XDS Packets 2.1 UTC AND TIMEZONES
1 OVERVIEW This application note describes how to properly encode Time of Day information using EIA-608-B Extended Data Services (XDS) packets. In the United States, the Public Broadcasting System (PBS)
QIP7232 P2. Hybrid QAM/IP High-definition Set-top. Quick Start Guide
QIP7232 P2 Hybrid QAM/IP High-definition Set-top Quick Start Guide Before You Begin Introduction Congratulations on receiving a Motorola QIP7232 Hybrid QAM/IP High-definition Set-top. This document will
REMOTE DISPLAY WIRELESS DECODER MK II
REMOTE DISPLAY WIRELESS DECODER MK II INSTALLATION MANUAL Part No. LED-DEC 1. Contents 1. Contents... 1 2. Equipment List... 2 3. Overview... 2 Introduction... 2 Location Selection **Important **... 2
Cable Calibration Function for the 2400B/C and 2500A/B Series Microwave Signal Generators. Technical Brief
Cable Calibration Function for the 2400B/C and 2500A/B Series Microwave Signal Generators Technical Brief Quickly and easily apply a level correction table to compensate for external losses or power variations
Setup Guide. Dolby PRM Rev. 1.1
Setup Guide Dolby PRM-4200 Rev. 1.1 Introduction CalMAN Required Software Version CalMAN Display Calibration Software can automatically create an optimized 3D calibration LUT for the Dolby PRM-4200 monitor.
VGA AUDIO AUDIO MATRIX SWITCHER S MANUAL
VGA AUDIO AUDIO MATRIX SWITCHER S MANUAL Milestone s VGA AUDIO AUDIO MATRIX Switcher is a unit whereby multiple (2/4/8) VGA AUDIO AUDIO input can be switched to two (2) or multiple (simultaneous) VGA AUDIO
STB Front Panel User s Guide
S ET-TOP BOX FRONT PANEL USER S GUIDE 1. Introduction The Set-Top Box (STB) Front Panel has the following demonstration capabilities: Pressing 1 of the 8 capacitive sensing pads lights up that pad s corresponding
FOM-1090 FOM-1090 FOM FOM-1090 w/ DB-25 Female FOM-1091 w/ DB-25 Male
Serial Data Communications Synchronous, Asynchronous or Isochronous Signal rates: DC to 20 MHz FOM-1090 w/ DB-25 Female FOM-1091 w/ DB-25 Male Supported Interface Standards TIA-530, TIA-530A TIA-232 TIA-574
RADIO FREQUENCY SYSTEMS
RADIO FREQUENCY SYSTEMS Optimizer RT FAQ s Q. What information is require before running the software? The Serial Number of each ACU MUST be recorded with the Model number of the antenna that it is attached
YAMAHA 03D SERIAL AUDIO MIXER
TECH NOTE Fastrack VS Verion 1.0 and later YAMAHA 03D SERIAL AUDIO MIXER The Fastrack VS hybrid editing system interfaces to the 03D Serial Audio Mixer with a 6-pin DIN to 9-pin RS-422 serial control cable
Anritsu Setup Procedure for GSP-1720 Measurements
GS 09-1313 Rev. 1.0 11-April-2009 Purpose: This procedure demonstrates how to use the Anritsu MT8803G to place a GSP-1720 modem into a call state. After the lab technician becomes familiar with this process,
The 01X Configuration Guide
The 01X Configuration Guide A Very Brief Introduction Welcome to the world of learning! Like many of you, I have spent countless hours reading and re-reading the 01x and the Cubase SX owner's manuals,
FR-8 and FR-16 Remote Control Operating Manual
FR-8 and FR-16 Remote Control Operating Manual Introduction The FR-8 and FR-16 are Ethernet-based remote control devices for Ashly Ethernet compatible products with DSP capabilities, including the Ashly
User s Guide W-E
Presto! PVR ISDB User s Guide 518100-02-01-W-E-112307-02 Copyright 2007, NewSoft Technology Corp. All Rights Reserved. No portion of this document may be copied or reproduced in any manner without prior
PAL B to VGA/ HDTV Tuner Box ID# 051
PAL B to VGA/ HDTV Tuner Box ID# 051 Operation Manual Introduction This unit allows you to view VHF/UHF/Cable TV, DVD movie and other videos on your PC monitor, LCD project or large screen HDTV or plasma
LDG M-7600 External Meter for Icom IC-7600
M-7600 OPERATIONS MANUAL MANUAL REV A LDG M-7600 External Meter for Icom IC-7600 LDG Electronics 1445 Parran Road St. Leonard MD 20685-2903 USA Phone: 410-586-2177 Fax: 410-586-8475 ldg@ldgelectronics.com
Multi-Zone Programmable RGB ColorPlus LED Touch Controller (Remote Control) and RGB ColorPlus LED Touch Controller (Receiver)
11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com Multi-Zone Programmable RGB ColorPlus LED Touch Controller (Remote Control) and RGB ColorPlus
WinFast. Digital TV Card QUICK INSTALLATION GUIDE. CODE: LR 66xx P/N: W05G0060 Ver: B
WinFast Ò Digital TV Card QUICK INSTALLATION GUIDE CODE: LR 66xx P/N: W05G0060 Ver: B Table of Contents Connect Input & Output Devices... 1 Board Layout... 2 Hardware Installation... 4 Driver & Application
Hardware Setup. HP Dual TV Tuner/Digital Video Recorder. Document Part Number:
Hardware Setup HP Dual TV Tuner/Digital Video Recorder Document Part Number: 374787-001 November 2004 This guide provides steps to help you set up your HP Dual TV Tuner/Digital Video Recorder hardware
HDMI to 3G-SDI Scaler Installation Guide
Introduction HDMI to 3G-SDI Scaler Installation Guide The HDMI to 3G-SDI Scaler allows you to broadcast HDMI signals from one source to two 3G-SDI outputs. Key Features and Benefits Convert HDMI signals
RFT-851FTA. Twin DVB-T to PAL remodulator. User Manual
RFT-851FTA Twin DVB-T to PAL remodulator User Manual 1. Purpose of use RFT-851FTA is designed for prosessing two COFDM modulated signals into standard CCIR channels. RFT-851FTA is supplied with a A2 stereo/dual/swap
Be sure to run the vehicle engine while using this unit to avoid battery exhaustion.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNE; Please Read all of these instructions regarding
Operation/Reference Guide IRIS. Infrared/Serial Data Capture Unit. Control System Accessories
Operation/Reference Guide IRIS Infrared/Serial Data Capture Unit Control System Accessories Last Revised: 1/17/2007 AMX Limited Warranty and Disclaimer All products returned to AMX require a Return Material
Tests on 3G-Base Stations to TS with FSIQ and SMIQ
Products: FSIQ, SMIQ Tests on 3G-Base Stations to TS 25.141 with FSIQ and SMIQ This application note describes how to measure the various WCDMA signals which are used for transmitter tests on FDD base
Calibrating and Profiling Your Monitor
Calibrating and Profiling Your Monitor For this module, you will need: Eye-One measurement device Counterweight (used for LCD screens only) New, modern displays are better First, you need to use a good
Syntor X Flash Memory Module Revision C
Syntor X Flash Memory Module Revision C The PIEXX SynXFlash memory module, along with the supplied PC software, replaces the original SyntorX code plugs and allows you to easily set modify and update your
Photos by N8IK (except first and last slide) 2015, Ian Keith, All Rights Reserved
I got in trouble at Hamvention this year. More trouble than I usually get into. I ordered a new K3S and a P3 panadapter from Elecraft. The usual crowd at the Elecraft booth looked like bears at a picnic.
JT65 HF Operator s Guide
VE3JW JT65 HF Operator s Guide An introduction to JT65: A weak signal high frequency digital mode. By: VE3BUX WSJT Modes Mode Typical Intended d Minimumi Notes Bands Propagation Mode Transmission Duration
MadiXtreme / Alpha-Link XLogic I/O system for PC and Mac Setup Guide V1.0 XLogic. This is SSL.
www.solidstatelogic.com MadiXtreme / Alpha-Link XLogic I/O system for PC and Mac Setup Guide V1.0 XLogic. This is SSL. Document History 82BSA101A March 2012 V1.0 Initial Release Contents Introduction 1
DATA PROJECTOR XJ-S30/XJ-S35
E DATA PROJECTOR XJ-S30/XJ-S35 User s Guide Be sure to read the precautions in the separate User s Guide (Basic Operation). For details about setting up the projector and lamp replacement, see the User
LED-DEC W07 REMOTE DISPLAY WIRELESS DECODER
LED-DEC W07 REMOTE DISPLAY WIRELESS DECODER INSTALLATION MANUAL 1. Contents 1. Contents... 1 2. Equipment List... 3 3. Overview... 3 3.1 Introduction... 3 3.2 Location Selection & Cabling *** Important
AIROCKS PRO ARX-900 USER GUIDE V3.2. AiRocks Pro ARX-900 Digital Wireless Audio Repeater. User Guide V3.2 February 17, 2016
AiRocks Pro ARX-900 Digital Wireless Audio Repeater User Guide V3.2 February 17, 2016 1 CONTENTS 1 Quick Start Guide... 5 1.1 Reset ARX-900 units to Factory Defaults... 5 1.2 Master Setup... 5 1.3 Relay
User s Manual RGB 302/304. Universal Digital Interface
User s Manual RGB 302/304 Universal Digital Interface Contents Chapter One Introduction to the RGB 302/304 RGB 302/304 Features... 1-1 SmartSave... 1-2 LCD Menu Driven Controls... 1-2 Memory Blocks and
DL-Navigator Operator Manual Post-Network Conversion (Version 6.1) Wisconsin BadgerNet Converged Network Room Control System- Pre-Network Conversion
DL-Navigator Operator Manual Post-Network Conversion (Version 6.1) Wisconsin BadgerNet Converged Network Room Control System- Pre-Network Conversion Contents Main Screen Zones How to Power Up Room How
END USER MANUAL DAS-M44HD-R
END USER MANUAL DAS-M44HD-R Warnings: Important Safety Instructions and Caution Please read all of these instructions regarding your unit and retain them for future reference Read this manual fully and
1 Unpack the projector. Quick Setup. EPSON PowerLite S1+ Your projector comes with the following items:
EPSON PowerLite S1+ Quick Setup 1 Unpack the projector Your projector comes with the following items: Projector Power cord Computer cable Computer Projector Projector remote control Presentation remote
INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM
INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM ATTENTION: READ THE ENTIRE INSTRUCTION SHEET BEFORE STARTING THE INSTALLATION PROCESS. WARNING! Do not begin to install your
CONTENTS Page 1.0 System Requirements Wi-Fi Settings Getting Started Mixer Window... 14
Welcome: Thank you for downloading the CL StageMix ipad app for the Yamaha CL series digital mixing consoles. The latest firmware version for CL series can be downloaded from https://www.yamaha.com/proaudio/
Stevens SatComm FAQs For use with SatCommSet or Terminal Setup programs
Stevens SatComm FAQs For use with SatCommSet or Terminal Setup programs Q. What are the channel assignments for On Air Test Mode? A. The assigned GOES test channels are as follows: GOES West 300 Baud:
Narrow-Band Emergency Message System (EBEMS) - MT-63 Operating Instructions
Narrow-Band Emergency Message System (EBEMS) - MT-63 Operating Instructions Dr. John A. Allocca, WB2LUA www.wb2lua.com 12/16/14 Narrow Band Emergency Messaging Software (NBEMS) is a system that allows
Lab Determining the Screen Resolution of a Computer
Lab 1.3.3 Determining the Screen Resolution of a Computer Objectives Determine the current screen resolution of a PC monitor. Determine the maximum resolution for the highest color quality. Calculate the
Transceiver Performance What s new in 2011?
Transceiver Performance What s new in 2011? Rob Sherwood NCØ B Lots of options for your dollars. Sherwood Engineering What is important in a contest or DX pile-up environment? Good Dynamic Range to hear
HDMI & VGA Receiver over IP with USB Connections - ID# & 15456
HDMI & VGA Receiver over IP with USB Connections - ID# 15455 & 15456 Operation Manual Introduction The 4K2K video and audio extender is multi-function extender supports up to 4K2K ultra high-definition
Digital TV Troubleshooting Tips
Analog Channels Only - Page 2 Analog Pass-Through: Making a Non-Analog Pass-Through Box Work - Page 2 Audio Vanishes on Some Programs, but Fine on Others - Page 2 Black Bars on Edges of Picture - Page
SM DMX LIGHTING CONTROLLER OWNERS MANUAL. May 19, 2009
SM - 192 DMX LIGHTING CONTROLLER OWNERS MANUAL May 19, 2009 INSTRUCTION MANUAL Page 2 of 8 MAIN FEATURES 192 DMX Channels 30 Scene Banks of 8 programmable scenes each 6 Programmable chases with up to 240
MyFlyDream TeleFlyPro V1.04
MyFlyDream TeleFlyPro V1.04 www.myflydream.com Notes Thank you for purchasing the MyFlyDream TeleFlyPro (hereinafter referred to as TFPro). Please follow this manual to get familiar with the TFPro and
PLL2710W LED LCD Monitor
PLL2710W LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 Package Overview...3 First Setup...4 Front View of the Product...5 Rear View of the Product...6
VGA & RS-232 & Audio CAT5 Extender with RGB Delay Control Quick Installation Guide
VGA & RS-232 & Audio CAT5 Extender with RGB Delay Control Quick Installation Guide Introducing the VGA & RS-232 & Audio CAT5 Extender with RGB Delay Control The VGA & RS-232 & Audio CAT5e Extender with
Classroom Setup... 2 PC... 2 Document Camera... 3 DVD... 4 Auxiliary... 5
Classroom Setup... 2 PC... 2 Document Camera... 3 DVD... 4 Auxiliary... 5 Lecture Capture Setup... 6 Pause and Resume... 6 Considerations... 6 Video Conferencing Setup... 7 Camera Control... 8 Preview
FULL MANUAL. HF/50 MHz TRANSCEIVER i7300 INTRODUCTION 1 PANEL DESCRIPTION 2 INSTALLATION AND CONNECTIONS 3 BASIC OPERATION
FULL MANUAL INTRODUCTION 1 PANEL DESCRIPTION 2 INSTALLATION AND CONNECTIONS 3 BASIC OPERATION HF/50 MHz TRANSCEIVER i7300 4 RECEIVING AND TRANSMITTING 5 SCOPE OPERATION 6 VOICE RECORDER FUNCTIONS 7 VOICE
Video Server SED-2100R/S. Quick Installation Guide
Video Server SED-2100R/S Quick Installation Guide Feb.10,2006 1 1 Getting Started 1.1 PACKAGE CONTENTS SED-2100 Warranty Card Software CD Hook up & Screws Terminal Blocks for Power & DI/O Power Adaptor
STR-ZA3100ES/STR-ZA2100ES/STR-
MULTI CHANNEL AV RECEIVER ZA00ES STR-ZA300ES/STR-ZA200ES/STR- Parts and Controls Receiver Front panel (with the front cover attached) [] Front panel (without the front cover attached) [2] Power indicator
with the Field-IQ Crop Input Control System
with the Field-IQ Crop Input Control System Quick Reference Card CONNECTING THE SYSTEM Ag25 GNSS antenna (P/N 68040-OOS) TNC/TNC right-angle cable (P/N 50449) Cable assembly, display to Field-IQ (P/N 50449)
Perle Fast Ethernet Fiber to Fiber Media Converter Module. Installation Guide. P/N (Rev D)
Perle Fast Ethernet Fiber to Fiber Media Converter Module Installation Guide C-100MM-XXXXX CM-100MM-XXXXX Unmanaged Module Managed Module P/N 5500313-10 (Rev D) Overview This document contains instructions
KVH Tri-Sat AutoSwitch Kit Installation and Operation Instructions for TracVision M3DX
KVH Tri-Sat AutoSwitch Kit Installation and Operation Instructions for TracVision M3DX A The following instructions explain how to install and operate the Tri-Sat AutoSwitch Kit on a TracVision M3DX system.
Transmitter Installation and Operation
Transmitter Installation and Operation Easy-to-follow instructions on how to program and use your Talking House / i A.M. Radio Transmitter Questions? Just call (616) 772-2300. Contents Quick Start... 3
CLOCKAUDIO. MR88 Automatic Microphone Mixer. Version 4.2
CLOCKAUDIO MR88 Automatic Microphone Mixer Version 4.2 Clockaudio Limited,22 Arnside Road WATERLOOVILLE Hampshire. UK Tel : +44 (0)2392 251193 Fax : +44 (0)2392 251201 Email : sales@clockaudio.co.uk CONTENTS
ELECRAFT P3 HIGH-PERFORMANCE PANADAPTER OWNER S MANUAL. Revision H1, November 25, 2016 E Copyright 2016, Elecraft, Inc. All Rights Reserved
ELECRAFT P3 HIGH-PERFORMANCE PANADAPTER OWNER S MANUAL Revision H1, November 25, 2016 E740152 Copyright 2016, Elecraft, Inc. All Rights Reserved Contents NOTE: IF YOU PURCHASED YOUR P3 AS A KIT, GO DIRECTLY
FV400 DIGITAL TV RECEIVER WITH MODULATOR INSTRUCTION MANUAL
FV400 DIGITAL TV RECEIVER WITH MODULATOR INSTRUCTION MANUAL Please read this instruction manual carefully before using your receiver Table of Contents Introduction-----------------------------------------------------------------------------
How-to Setup Motion Detection on a Dahua DVR/NVR
How-to Setup Motion Detection on a Dahua DVR/NVR Motion detection allows you to set up your cameras to record ONLY when an event (motion) triggers (is detected) the DVR/NVR to begin recording and stops
3G-SDI to HDMI Scaler Installation Guide
Introduction 3G-SDI to HDMI Scaler Installation Guide The 3G-SDI to HDMI Scaler allows you to broadcast 3G-SDI signals from one source to two 3G-SDI and one HDMI outputs. Key Features and Benefits Converts
KAT5.tv AV Distribution System. KAT5 AVRX User Guide
KAT5 AVRX Mk2 AV Receiver User Guide Version 1.0 1 st August 2005 Overview The KAT5 AVRX is a device that receives electronically balanced AV signals over a CAT5 Structured Wiring Scheme Used with the
BodyBeat Metronome Instruction Manual
BodyBeat Metronome Instruction Manual Peterson Electro-Musical Products, Inc. 2013 Power The StroboPlus contains a powerful internal rechargeable Lithium-Ion battery. Before initial use, we recommend that
Any feature not specifically noted as supported is not supported.
Manufacturer: ELAN Integration Note Model Number(s): EL-4KM-VW44 (Device Ver 2.20; Web Module Ver 6.23) Minimum Core Module Version: Document Revision Date: 8.1.395 5/11/2017 OVERVIEW AND SUPPORTED FEATURES
Optiflex Interactive Video System
Optiflex Interactive Video System Optiflex Interactive Video System 1 Before You Start...............2 On-site Video Surveillance.......6 Touchscreen Interface Viewing...10 Secure Remote Look-in........16
Installation Guide AT-HDR-EX-70-2PS
4K HDR HDMI Over TX/RX Kit The Atlona is an transmitter/receiver kit for high dynamic range (HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as
Tektronix RSA306 USB Spectrum Analyzer
Tektronix RSA306 USB Spectrum Analyzer Simple Demos The Demo of the RSA306 is easy. Even you do not have signal generators, devices under test, or demo boards, using the whip antenna provided in box, you
Mobile DTV Viewer. User Manual. Mobile DTV ATSC-M/H DVB-H 1Seg. Digital TV ATSC DVB-T, DVB-T2 ISDB-T V 4. decontis GmbH Sachsenstr.
Mobile DTV ATSC-M/H DVB-H 1Seg Digital TV ATSC DVB-T, DVB-T2 ISDB-T V 4 decontis GmbH Sachsenstr. 8 02708 Löbau Germany +49 3585 862915 +49 3585 415629 www.com dvbsam@com 1 Introduction... 5 2 System Requirements...
Camera Setup Instructions
Camera Setup Instructions Hopefully this document will help new MallinCam owners set up their systems and get them to successful first light more quickly. Through the use of images, I hope to describe
STR-ZA5000ES. Parts and Controls. Preparation. Receiver. Remote control. 1. Installing speakers. 2. Connecting speakers. 3.
MULTI CHANNEL AV RECEIVER STR-ZA5000ES Parts and Controls Receiver Front panel (with the front cover attached) [] Front panel (without the front cover attached) [] Power indicator [] Indicators on the
Vortex / VSX TM 8000 Integration
Vortex / VSX TM 8000 Integration Application Note Polycom Installed Voice Business Group December 2004 1 TABLE OF CONTENTS INTRODUCTION...4 CONNECTING THE VSX 8000 INPUTS AND OUTPUTS...4 ENABLING THE VSX
CONNECTOR A (BLACK 4 PIN) LED S CONNECTOR B (WHITE 4 PIN) CONNECTOR C (WHITE 5 PIN) CONNECTOR D (WHITE 2 PIN) 1x device. 2x - 10x
SIC3-RFK FIRMWARE 2.0.4 A B CONNECTOR A (BLACK 4 PIN) TO BYPASS OR REMOTE STARTER LED S CONNECTOR B (WHITE 4 PIN) TO SOLACE ANTENNA ( NOT INCLUDED ) CONNECTOR C (WHITE 5 PIN) GRAY / BLACK - START / STOP
RUBY 7 HD+ Handheld Video Magnifier. User s Guide. Freedom Scientific, Inc Rev. A
RUBY 7 HD+ Handheld Video Magnifier User s Guide Freedom Scientific, Inc. www.freedomscientific.com 440931-001 Rev. A Freedom Scientific, Inc., 11800 31 st Court North, St. Petersburg, Florida 33716-1805,
and Re:system MR-Slave Module Dominating Entertainment. Revox of Switzerland.
and MR-Slave Module Dominating Entertainment. Revox of Switzerland. Contents MR Slave Assembly Connection MR Bus MR Slave cabling 2 3 4 4 5-7 Multiroom Setup Import list Importing sources The new Source
Multiroom Solution Guide HDR-3000T + H3
Multiroom Solution Guide HDR-3000T + H3 Contents What s in the box?... 3 How multiroom solution works... 4 How to connect H3 and HDR-3000T... 5 How to pair H3 and HDR-3000T... 7 What you can do with multiroom
DVB-E65-TV. Compatible with BMW E65 Professional navigation systems with 8.8 monitor
dvblogic DVB-T Tuner Compatible with BMW E65 Professional navigation systems with 8.8 monitor Vehicles with factory TV-tuner port (Factory TV-tuner must be uninstalled) Product features Full plug and play
SATFINDER 3 HD SLIM USER GUIDE
SATFINDER 3 HD SLIM USER GUIDE INDEX General Safety..... 3 Key Features..... 4 Panel Keypads... 5 Accesory.. 6 Satellite Search...... 7 Spectrum..... 8 Cross Polarisation... 9 Packet TP Levels.... 9 Multi
CONTROL PANEL ENGLISH INSTRUCTIONS MOTORLINE MC 2 / SEAV LRS 2150 SET
CONTROL PANEL ENGLISH INSTRUCTIONS MOTORLINE MC 2 / SEAV LRS 2150 SET 230 Volt Single Phase logic control panel for twin motors pair of swinging gates and single leaf swing gate Integral radio receiver,
Lindell 354E User Manual. Lindell 354E. User Manual
Lindell354EUserManual Lindell 354E User Manual Introduction Congratulation on choosing the Lindell 354E multi band compressor. This plugin faithfully reproduces the behavior and character of the most famous
2.0 Installation Guide
2.0 Installation Guide Mediatune 2.0 was designed to work with the CHROME browser on the PC and the Safari browser on the ipad. While you may be able to get other browsers to work, you will have the best
MONOPRICE. BitPath AV VGA Wireless Transmitter & Receiver Kit, 200m. User's Manual P/N 16224
MONOPRICE BitPath AV VGA Wireless Transmitter & Receiver Kit, 200m P/N 16224 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention
CL StageMix V6 User Guide
Welcome: Thank you for downloading the CL StageMix ipad app for the Yamaha CL series digital mixing consoles. The latest firmware version for CL series can be downloaded from www.yamahaproaudio.com StageMix
Model VS-2A 2-Port VGA Switch with Audio & Serial Control
Model VS-2A 2-Port VGA Switch with Audio & Serial Control UMA1119 Rev B Copyright Hall Research, Inc. All rights reserved. 1163 Warner Ave Tustin, CA 92780, Ph: (714)641-6607, Fax -6698 Model VS-2A 2 2-Port
Dragon. manual version 1.6
Dragon manual version 1.6 Contents DRAGON TOP PANEL... 2 DRAGON STARTUP... 2 DRAGON STARTUP SCREEN... 2 DRAGON INFO SCREEN... 3 DRAGON MAIN SCREEN... 3 TURNING ON A TRANSMITTER... 4 CHANGING MAIN SCREEN
Element 78 MPE-200. by Summit Audio. Guide To Operations. for software version 1.23
Element 78 MPE-200 by Summit Audio Guide To Operations for software version 1.23 TABLE OF CONTENTS IMPORTANT SAFETY AND GROUNDING INSTRUCTIONS COVER 1. UNPACKING AND CONNECTING...3 AUDIO CONNECTIONS...4
This module senses temperature and humidity. Output: Temperature and humidity display on serial monitor.
Elegoo 37 Sensor Kit v2.0 Elegoo provides tutorials for each of the sensors in the kit provided by Maryland MESA. Each tutorial focuses on a single sensor and includes basic information about the sensor,
DIGITAL DISTRIBUTING FRAME (DDF) INSTALLATION PROCEDURES FOR PANELS AND MODULES
DIGITAL DISTRIBUTING FRAME (DDF) INSTALLATION PROCEDURES FOR PANELS AND MODULES CommScope 365-301-136-1 Instruction Sheet Issue 10, February 2004 Material ID 847 591 963 General The Digital Distributing
General. zoom ring. focus ring. Size of liquid. Color. foot adjust levers. Projection. Computer In. Mouse/Com. Power
Projector Specifications status lights control panel speakers zoom ring focus ring General Type of display Size of liquid crystal panels Poly-silicon Thin Film Transistor (TFT), active matrix Diagonal: