Troubleshooting Guide

Transcription

1 Order No. ITD BE TC-54Z1 Troubleshooting Guide <D 2009 Model> TC-54Z1 TC-54/50V10 TC-50/46/42G15 TC-54/50/46/42G10 TC-54/50/46/42S1 TC-50/46/42U1 This service hint is published for technicians and engineers for repair. nd it gives you the information how to judge the defective board of D. In the future,we will improve the contents for more easy diagnostic and trouble shooting. - Ver 1.0- anasonic Corporation Unauthorized copying and distribution is a violation of law.

2 Contents D Line up & Feature Comparison CB Location & Function CB List Block Diagram Troubleshooting Important information (for TC-54Z1)

3 D Line up & Feature Comparison (Full HD model) 3

4 D Line up & Feature Comparison Z1 Series V10 Series G15 Series G10 Series S1 Series U1 Series icuture Sound Size 54 54/50 50/46/42 54/50/46/42 54/50/46/42 50/46/42 anel 1080p HD NeoD 1080p HD NeoD 1080p HD NeoD 1080p HD NeoD 1080p HD NeoD 1080 HD Screen Coating (Filter) New Louver Filter New R Filter New R Filter New R Filter New R Filter --- Gradation 6,144 6,144 6,144 6,144 6,144 5,120 Contrast Ratio 40,000:1 40,000:1 40,000:1 40,000:1 40,000:1 30,000:1 Moving icture Resolution 1080 lines 1080 lines 1080 lines 1080 lines 1080 lines 900 lines 600 Hz Sub-field Drive Y Y Y Y Y Y x.v. Colourr Y Y Y Y p Cinematic layback Y Y THX Mode Y Y Y Digital Cinema Colour --- Y Deep Color Y Y Y Y Y Y dvanced 3D Colour Management Y Y Y Y Motion attern Noise Reduction Y Y Y Y Y Y Sub ixel Control Y Y Y Y Speaker Woofer/Tweeter Full-range Full-range Full-range Full-range Full-range BBE VIV Y Y HDMI 4+1(Output) Y Y Y Y VIER Link (with Network Camera) (with Network Camera) (with Network Camera) (with Network Camera) Y Y VIER CST (ITV) Y Y Y Y Networking VIER Image Viewer VCHD/MEG2 /JEG playback VCHD/MEG2 /JEG playback VCHD/MEG2 /JEG playback VCHD/MEG2 /JEG playback JEG playback JEG playback Game Mode Y Y Y Y Y --- C Input Y Y Y Y

5 2. CB Location & Function (Full HD model) 5

6 2. CB Location & Function TC-54Z1 TC-54Z1M (Display unit) TU-Z100U (Tuner Box) TU-WH1U (Wireless unit) J B (S) (MULTI) D GL SG K (FILTER) GH C3 S 2 K RM DH GS G Q TU-WHT1U (Transmitter) WT WH RM TU-WHR1U (Receiver) WR RM Board Name Function art Number ower Supply (S) XMM718S ower Supply (MULTI) XMM718BS ower Supply (FILTER) XMM718CS D Digital Signal rocessor TZTN01DKUU GH HDMI in TXNGH1DKUU B Fan control TN4864C S ower Switch TN4863 K Remote receiver, TN4862 ower LED, C..T.S sensor SG Card Slot TN4860B GL Blue LED TN4693F J Connection for Key Switch TN4944 Data Driver (Lower Right) TN4770C Data Driver (Lower Center) TN4771C C3 Data Driver (Lower Left) TN4772C Scan Drive TN4840D Sustain Drive TN4841D 2 Sustain connector (Lower) TN4843 Scan out (Upper), TN4790B -Board should be Scan out (Lower), TN4791B -Board should be Board Name Function art Number Q ower Supply N0B2FF00002 Q-Board should be Digital Signal rocessor TZTN02DKUU DH HDMI out TXNDH1DKUU G Front Terminal TXN/G1DKUU GS Card Slot, HDMI4 in TXNGS1DKUU K ower Switch, TN4869B Key Switch, ower LED, LED RM RF in RM-Board should be TN4870 Wireless unit (Transmitter) Board Name Function art Number WT WiHD Transmitter WH WiHD Host RM RF Tx TXNRM1JJ Wireless unit (Receiver) Board Name Function art Number WR WiHD Receiver RM RF Rx TXNRM2JJ Caution. C. B. should be WT board (in a transmitter), WH board (in a transmitter) and WR board (in a receiver) should be exchanged at the same time for repair because these boards are initialized security settings in a factory in order to obey a copyright protection. Repair of these three boards should be done by replacing complete unit pair (TRNSMIION/RECEIVE UNIT, art No.TZTWH01JU). 6

7 2. CB Location & Function V10 Series TC-54V10 TC-50V10 (-2) (-1) GK GL K C3 S 2 GK GL K C3 S 2 Board Board Name Function art Number Name Function art Number ower Supply ETX2MM761MGN ower Supply ETX2MM747FK DC-DC Converter, TXN/1DQUUS DC-DC Converter, TXN/1DRUUS Tuner,Speaker out, C, Tuner,Speaker out, C, V Terminal, V Switch, V Terminal, V Switch, Digital Signal rocessor, Digital Signal rocessor, SYSTEM MU, SYSTEM MU, HDMI Switch,eaks-VC, HDMI Switch,eaks-VC, Ethernet,Format Converter, Ethernet,Format Converter, lasma I, lasma I, Sub-Field rocessor Sub-Field rocessor K Remote receiver, TN4872S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S GL blue LED TN4693ES Data Driver (Lower Right) TXN1ECUU Data Driver (Lower Center) TXN1ECUU C3 Data Driver (Lower Left) TXNC31ECUU Scan Drive TXN1DQUU Sustain Drive TXN1DQUU 2 Sustain out (Lower) TN4804S Scan out (Upper) -Board should be Scan out (Lower) -Board should be TXN1ECUU TXN1ECUU K Remote receiver, TN4872S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S GL blue LED TN4693ES Data Driver (Lower Right) TXN1EDUU Data Driver (Lower Center) TXN1EDUU C3 Data Driver (Lower Left) TXNC31EDUU Scan Drive TXN1DRUU Sustain Drive TXN1DRUU 2 Sustain out (Lower) TN4804S Scan out (Upper) TN4788 -Board should be Scan out (Lower) -Board should be TN4789 7

8 2. CB Location & Function G15 Series TC-50G15 TC-46G15 TC-42G15 GK K C3 S 2 GK K C3 S 2 GK K S 2 Board Name Function art Number ower Supply ETX2MM747FK DC-DC Converter, TXN/1FFUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor K Remote receiver, TN4871S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EDUU Data Driver (Lower Center) TXN1EDUU C3 Data Driver (Lower Left) TXNC31EDUU Scan Drive TXN1DRUU Sustain Drive TXN1DRUU 2 Sustain out (Lower) TN4804S Scan out (Upper), TN4788 -Board should be Scan out (Lower), TN4789 -Board should be Board Name Function art Number ower Supply ETX2MM747FK DC-DC Converter, TXN/1FGUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor K Remote receiver, TN4871S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1DXUC Data Driver (Lower Center) TXN1DXUC C3 Data Driver (Lower Left) TXNC31DXUC Scan Drive TXN1DXUE Sustain Drive TXN1DXUE 2 Sustain out (Lower) TXN21DYUC Scan out (Upper), -Board should be Scan out (Lower), -Board should be TN4786 TN4787 Board Name Function art Number ower Supply ETX2MM747FF DC-DC Converter, TXN/1FHUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor K Remote receiver, TN4871S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EFUU Data Driver (Lower Left) TXN1EFUU Scan Drive TXN1FHUU Sustain Drive TXN1FHUU 2 Sustain out (Lower) TN4802S Scan out (Upper), -Board should be TN4784 Scan out (Lower), TN4785 -Board should be 8

9 2. CB Location & Function G10 Series TC-54G10 TC-50G10 TC-46G10 TC-42G10 (-2) (-1) GK K S C3 2 GK K C3 S 2 GK K C3 S 2 GK K S 2 Board Name K Function art Number ower Supply ETX2MM761MGN DC-DC Converter, TXN/1DVUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1ECUU Data Driver (Lower Center) TXN1ECUU C3 Data Driver (Lower Left) TXNC31ECUU Scan Drive TXN1ECUU Sustain Drive TXN1ECUU 2 Sustain out (Lower) TN4804S Scan out (Upper) TXN1ECUU -Board should be Scan out (Lower) -Board should be TXN1ECUU Board Name K Function art Number ower Supply ETX2MM747FK DC-DC Converter, TXN/1DWUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EDUU Data Driver (Lower Center) TXN1EDUU C3 Data Driver (Lower Left) TXNC31EDUU Scan Drive TXN1EDUU Sustain Drive TXN1EDUU 2 Sustain out (Lower) TN4804S Scan out (Upper) -Board should be Scan out (Lower) -Board should be TN4788 TN4789 Board Name Function art Number ower Supply ETX2MM747FK DC-DC Converter, TXN/1DXUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1DXUC Data Driver (Lower Center) TXN1DXUC C3 Data Driver (Lower Left) TXNC31DXUC Scan Drive TXN1DXUC Sustain Drive TXN1DXUC 2 Sustain out (Lower) TXN21DYUC Scan out (Upper) -Board should be Scan out (Lower) -Board should be TN4786 TN4787 Board Name Function ower Supply ETX2MM747FF DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,eaks-VC, Ethernet,Format Converter, lasma I, Sub-Field rocessor TXN/1DYUUS K Remote receiver, ower LED, C..T.S sensor art Number TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EFUU Data Driver (Lower Left) TXN1EFUU Scan Drive TXN1EFUU Sustain Drive TXN1EFUU 2 Sustain out (Lower) TN4802S Scan out (Upper) TN4784 -Board should be Scan out (Lower) TN4785 -Board should be 9

10 2. CB Location & Function S1 Series TC-54S1 TC-50S1 TC-46S1 TC-42S1 (-2) (-1) GK K S C3 2 GK K C3 S 2 GK K C3 S 2 GK K S 2 Board Name Function art Number ower Supply ETX2MM761MGN DC-DC Converter, TXN/1ECUUS Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor Board Name Function art Number ower Supply ETX2MM747FK DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EDUUS Board Name Function art Number ower Supply ETX2MM747FK DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EEUUS Board Name Function art Number ower Supply ETX2MM747FF DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EFUUS K Remote receiver, TN4871S ower LED, C..T.S sensor S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1ECUU Data Driver (Lower Center) TXN1ECUU C3 Data Driver (Lower Left) TXNC31ECUU Scan Drive TXN1ECUU Sustain Drive TXN1ECUU 2 Sustain out (Lower) TN4804S Scan out (Upper), TXN1ECUU -Board should be Scan out (Lower), TXN1ECUU -Board should be K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EDUU Data Driver (Lower Center) TXN1EDUU C3 Data Driver (Lower Left) TXNC31EDUU Scan Drive TXN1EDUU Sustain Drive TXN1EDUU 2 Sustain out (Lower) TN4804S Scan out (Upper), TN4788 -Board should be Scan out (Lower), TN4789 -Board should be K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1DXUC Data Driver (Lower Center) TXN1DXUC C3 Data Driver (Lower Left) TXNC31DXUC Scan Drive TXN1DXUC Sustain Drive TXN1DXUC 2 Sustain out (Lower) TXN21DYUC Scan out (Upper), TN4786 -Board should be Scan out (Lower), TN4787 -Board should be K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EFUU Data Driver (Lower Left) TXN1EFUU Scan Drive TXN1EFUU Sustain Drive TXN1EFUU 2 Sustain out (Lower) TN4802S Scan out (Upper), TN4784 -Board should be Scan out (Lower), TN4785 -Board should be 10

11 2. CB Location & Function U1 Series TC-50U1 TC-46U1 TC-42U1 GK K C3 S 2 GK K C3 S 2 GK K S 2 Board Name Function art Number ower Supply ETX2MM747FG DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EHUUS K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EDUU Data Driver (Lower Center) TXN1EDUU C3 Data Driver (Lower Left) TXNC31EDUU Scan Drive TXN1EHUU Sustain Drive TXN1EHUU 2 Sustain out (Lower) TN4804S Scan out (Upper), -Board should be Scan out (Lower), -Board should be TXN1EHUU TXN1EHUU Board Name Function art Number ower Supply ETX2MM747FG DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EJUUS K Remote receiver, ower LED, C..T.S sensor TN4871S S ower Switch TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1DXUC Data Driver (Lower Center) TXN1DXUC C3 Data Driver (Lower Left) TXNC31DXUC Scan Drive TXN1EEUC Sustain Drive TXN1EEUC 2 Sustain out (Lower) TXN21DYUC Scan out (Upper), -Board should be Scan out (Lower), -Board should be TXN1EEUC TXN1EEUC Board Name Function art Number ower Supply ETX2MM747FE DC-DC Converter, Tuner,Speaker out, C, V Terminal, V Switch, Digital Signal rocessor, SYSTEM MU, HDMI Switch,Seine 3LV, Format Converter, lasma I, Sub-Field rocessor TXN/1EKUUS K S Remote receiver, ower LED, C..T.S sensor ower Switch TN4871S TN4873S GK Key Switch TN4874S Data Driver (Lower Right) TXN1EFUU Data Driver (Lower Left) TXN1EFUU Scan Drive TXN1EKUU Sustain Drive TXN1EKUU 2 Sustain out (Lower) TN4802S Scan out (Upper), -Board should be Scan out (Lower), -Board should be TN4784 TN

12 3. CB List (Full HD model) 12

13 3. CB List (except TC-54Z1) V10 series G15 series G10 series S1 series U1 series Board TC-54V10 TC-50V10 TC-50G15 TC-46G15 TC-42G15 TC-54G10 TC-50G10 TC-46G10 TC-42G10 TC-54S1 TC-50S1 TC-46S1 TC-42S1 TC-50U1 TC-46U1 TC-42U1 ETX2MM761MGN ETX2MM747FK ETX2MM747FK ETX2MM747FK ETX2MM747FF ETX2MM761MGN ETX2MM747FK ETX2MM747FK ETX2MM747FF ETX2MM761MGN ETX2MM747FK ETX2MM747FK ETX2MM747FF ETX2MM747FG ETX2MM747FG ETX2MM747FE TXN/1DQUUS TXN/1DRUUS TXN/1FFUUS TXN/1FGUUS TXN/1FHUUS TXN/1DVUUS TXN/1DWUUS TXN/1DXUUS TXN/1DYUUS TXN/1ECUUS TXN/1EDUUS TXN/1EEUUS TXN/1EFUUS TXN/1EHUUS TXN/1EJUUS TXN/1EKUUS K S GK GL C3 TN4872S TN4872S TN4871S TN4871S TN4871S TN4871S TN4871S TN4871S TN4871S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TN4693ES TN4693ES TXN1ECUU TXN1EDUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1ECUU TXN1EDUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXNC31ECUU TXNC31EDUU TXNC31EDUUTXNC31DXUC ---- TXNC31ECUU TXNC31EDUU TXNC31DXUC ---- TN4871S TN4871S TN4871S TN4871S TN4871S TN4871S TN4871S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4873S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TN4874S TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1EDUU TXN1DXUC TXN1EFUU TXNC31ECUU TXNC31EDUU TXNC31DXUC ---- TXNC31EDUU TXNC31DXUC ---- TXN1DQUU TXN1DRUU TXN1DRUU TXN1DXUE TXN1FHUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1EHUU TXN1EEUC TXN1EKUU 2 TXN1DQUU TXN1DRUU TXN1DRUU TXN1DXUE TXN1FHUU TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TN4804S TN4804S TN4804S TXN21DYUC TN4802S TN4804S TN4804S TXN21DYUC TN4802S TXN1ECUU TN4788 TN4788 TN4786 TN4784 TXN1ECUU TN4788 TN4786 TN4784 TXN1ECUU TN4789 TN4789 TN4787 TN4785 TXN1ECUU TN4789 TN4787 TN4785 TXN1ECUU TXN1EDUU TXN1DXUC TXN1EFUU TXN1EHUU TXN1EEUC TXN1EKUU TN4804S TN4804S TXN21DYUC TN4802S TN4804S TXN21DYUC TN4802S TXN1ECUU TN4788 TN4786 TN4784 TXN1EHUU TXN1EEUC TN4784 TXN1ECUU TN4789 TN4787 TN4785 TXN1EHUU TXN1EEUC TN

14 4. Block Diagram (Full HD model) 14

15 4.Block Diagram Signal rocessing Circuit (1) TH-54Z1 <CB Function> [ Tuner box ] [ Display unit ] HDMI 3 HDMI 2 HDMI 1 GS HDMI 4 Slot TV Tuner Video 1 in Comp 1 in Comp 2 in G Video 2 in C Digital nalog IC3801 IC7702 IC8300 IC3001 nalog IC4510 DV7471 IC8001 O eaks VC IC5100 GC6 IC5200 I500 DH IC9401 IC9005 IC9004 HDMI OUT Wireless HD SG Slot GH IC3901 D I9003 I8001 I5110 O Genx7 eaks VC I1100 LVDS I9300 Genx8 D3-H I4510 I5100 DV7471 GC6 I9500 Video Data Discharge Control for Discharge Control for anel C3 2 ETHER NET RUN IC8302 RS-232C I009 I100 Genx8 IC3001 : Video Switch (udio Switch) IC8302 : ETHER NET I/F I009 : RS-232C Driver IC3801 : HDMI EQULIZER IC7702 : -USB CONV. IC4510 : DV7471 (HDMI I/F, 10bit /D) IC8300 : Front End rocessor IC8001 : eaks VC (Digital Video rocessor) IC5100 : GC6 Video rocessor IC (Format Converter) LVDS Transmitter IC5200 :LVDS RX I100 : Genx8 (SYSTEM MU) IC9401 : LVDS RX IC9005 : KYOTO IC9004 : LVDS TX IC3901 : HDMI EQULIZER I4510 : DV7471 (HDMI I/F, 10bit /D) I5100 : GC6 Video rocessor IC (Format Converter) LVDS Transmitter I8001 : eaks VC (Digital Video rocessor) I5110 : LVDS RX I1100 : Genx8 (SYSTEM MU) I9300 : D3-H LVDS Receiver, Sub Field rocessor, Data Driver rocessor lasma I I9500 : FG (Discharge Control) I9003 : Genx7 (anel Micom) 15

16 4.Block Diagram <CB Function> Signal rocessing Circuit (2) TH-54V10 HDMI 4 HDMI 3 HDMI 2 HDMI 1 IC4510 DV7471 IC9003 Genx7 TV Tuner Video 1 in Video 2 in Comp 1 in Digital nalog IC3001 IC8300 nalog IC8001 eaks VC IC5110 O IC5100 GC6 LVDS IC9300 D3-H anel C3 2 Comp 2 in C Monitor out Slot IC9500 Discharge Control for Discharge Control for Video Data ETHER NET RUN IC8302 RS-232C I009 I100 Genx8 IC3001 : Video Switch (udio Switch) IC8300 : Front End rocessor IC8302 : ETHER NET I/F I009 :RS-232C Driver IC4510 : DV7471 (HDMI I/F, 10bit /D) IC8001 : eaks VC (Digital Video rocessor) IC5110 :LVDS RX IC5100 : GC6 Video rocessor IC (Format Converter) LVDS Transmitter I100 : Genx8 (SYSTEM MU) IC9300 : D3-H LVDS Receiver, Sub Field rocessor, Data Driver rocessor lasma I IC9500 : FG (Discharge Control) IC9003 : Genx7 (anel Micom) 16

17 4.Block Diagram <CB Function> Signal rocessing Circuit (3) TH-50G15/G10 HDMI 3 (Side) HDMI 2 HDMI 1 IC4510 DV7471 IC9003 Genx7 TV Tuner Video 1 in Video 2 in (Side) Comp 1 in Digital nalog IC3001 IC8300 nalog IC8001 eaks VC IC5110 O IC5100 GC6 LVDS IC9300 D3-H anel C3 2 Comp 2 in C Monitor out IC9500 Discharge Control for Discharge Control for Video Data Slot ETHER NET RUN IC8302 I100 Genx8 IC3001 : Video Switch (udio Switch) IC8300 : Front End rocessor IC8302 : ETHER NET I/F IC4510 : DV7471 (HDMI I/F, 10bit /D) IC8001 : eaks VC (Digital Video rocessor) IC5110 :LVDS RX IC5100 : GC6 Video rocessor IC (Format Converter) LVDS Transmitter I100 : Genx8 (SYSTEM MU) IC9300 : D3-H LVDS Receiver, Sub Field rocessor, Data Driver rocessor lasma I IC9500 : FG (Discharge Control) IC9003 : Genx7 (anel Micom) 17

18 4.Block Diagram <CB Function> Signal rocessing Circuit (4) TH-50S1/U1 HDMI 3 (Side) HDMI 2 IC4503 HDMI DT IC9003 Genx7 HDMI 1 O Digital TV Tuner nalog LVDS IC9300 anel Video 1 in Video 2 in (Side) IC3001 nalog IC8001 Seine3LV D3-H C3 2 Comp 1 in Comp 2 in IC9500 Discharge Control for Discharge Control for Video Data Slot I100 IC3001 : Video Switch (udio Switch) IC4503 :HDMI Switch IC8001 : Seine3LV (Digital Video rocessor) LVDS Transmitter I100 : SYSTEM MU IC9300 : D3-H LVDS Receiver, Sub Field rocessor, Data Driver rocessor lasma I IC9500 : FG (Discharge Control) IC9003 : Genx7 (anel Micom) 18

19 6. Troubleshooting (Full HD model) 19

20 5.Troubleshooting for picture trouble Relation of board and display area We know the possible defective board by picture trouble area. <Display device block diagram> (Back side view) <Relation of defective board and picture trouble area > (Back side view) IC9500 discharge control IC9300 Sub Filed rocessor Test-pattern N CONTROL anel C3 2 (all) (all) Video Data Video Data C3 STIN CONTROL (all) * In case of TC-54Z1, change to D 20

21 5.Troubleshooting for picture trouble icture trouble ( diagnosis of vertical line ) D panel defective (Data driver IC defective) Width is narrower than FC Data driver IC or C or board defective Width is same as FC Data driver IC defect= D panel defect D panel D panel 1 line defect defect bout 6-7.5cm Data driver IC Data driver IC C board C board Buffer IC Buffer IC board * In case of TC-54Z1, change to D 21

22 5.Troubleshooting for picture trouble Summary of picture trouble < Some part of screen > * In case of TC-54Z1, change to D Symptom ctual symptom Defective board Trouble at Upper or Lower half / board Horizontal line (Upper or Lower side) / board or D panel Trouble at Left or Center or Right part (42inch : Left or Right half) -C3 board (42inch :,) Vertical line (Width is same as FC) C or board or D panel Vertical line (Width is narrower than FC) D panel Regularly bar board 22

23 5.Troubleshooting for picture trouble < ll area of screen > Symptom Irregular Color Summary of picture trouble * In case of TC-54Z1, change to D ctual symptom Defective board board ll vertical line board bnormal electric discharge / board 23

24 5.Troubleshooting for picture trouble Diagnosis by Test attern <urpose> Test pattern is helpful to find the defective parts. For example, if we can see the picture problem at all over the screen (icture Noise, Full Vertical Line,abnormal color), we can find signal processing problem or panel phosphor problem by using test pattern. <Model> Full HD Models (V10,G15,G10,S1,U1 series) <Symptom> icture Noise, Full Vertical Line,abnormal color <How to enter the Test attern> 1.ress the VOLUME - on the TV set and push INFO button of remote controller 3 times at the same time. 2. fter this procedure, you can enter Service Mode and select ging, then Test pattern will appear. 3. ush 3" button of Remote Controller to select the test pattern mode to forward. 4. ush 4 button of Remote Controller to select the test pattern mode to reverse. <Diagonosis> How to diagnose by using test pattern bnormal picture (icture Noise, Full Vertical Line,abnormal color) <Test attern (Normal)> Tuner Block (1-3) anel Block (4-20) TIME 0 1:R/G/B/W 20:Dark Blue 19:Dark Green 18:Dark Red 0 2: Black 3:White 4:White 5:Red 6:Green 7:Blue 8:ON/OFF (with character) ging 17:White Frame 16:Scroll No picture 15: and B zone 14:Color bar 13:1% Window 12:Ramp Blue 9:Ramp White 10:Ramp Red 11:Ramp Green Test pattern (4-20) Defective Block (Board) Test pattern Defective Block (Board) bnormal anel Block ( or C Board or anel) No picture anel Block ( or C Board or anel) Normal Tuner Block ( Board) O.K Tuner Block ( Board) 24

25 5.Troubleshooting for picture trouble Diagnosis by Test attern [TC-54Z1] (1/2) <Model> Full HD Models (TC-54Z1) <Symptom> icture Noise, Full Vertical Line,abnormal color <How to enter the Test attern> Use RF Remote control. 1.ress the VOLUME [-] button of tuner box and push [INFO] button of RF remote control 3 times within 2 seconds. - Service mode of tuner box is displayed. (Blue background) 2.By 1 or 2 button, select [MONITOR] and press [OK] button. 3.[MONITOR MODE] will be displayed on the left-top of the screen and switch to service mode of display unit is completed. 4.ress VOLUME [-] button of Display unit + [INFO] button of RF remote control 3 times within 2 seconds. - Service mode of display unit is displayed.(green background) 5. fter this procedure, you can enter Service Mode and select ging, then Test pattern will appear. 6. ush 3" button of Remote Controller to select the test pattern mode to forward. 7. ush 4 button of Remote Controller to select the test pattern mode to reverse. SERVICE DJUST OTION SRV-TOOL MONITOR MONITOR 1,2 :MIN SELECT OK :ENTER DYNMIC 00 9 :ICTURE MENU SELECT [MONITOR MODE] MONITOR MODE SERVICE DJUST WB-DJ OTION GING SRV-TOOL MONITOR MODE (Blue background) (Green background) Use IR Remote control. 1. ress the VOLUME [-] button of the display unit and push [INFO] button of IR remote control 3 times within 2 seconds. 2. fter this procedure, you can enter Service Mode and select ging, then Test pattern will appear. 3. ush 3" button of Remote Controller to select the test pattern mode to forward. 4. ush 4 button of Remote Controller to select the test pattern mode to reverse. (Next page) 25

26 5.Troubleshooting for picture trouble Diagnosis by Test attern [TC-54Z1] (2/2) <Test attern (Normal)> TIME 0 1:R/G/B/W 0 2: Black 3:White 4:White 5:Red 6:Green 7:Blue 8:ON/OFF (with character) ging 9:Ramp White 20:Dark Blue 10:Ramp Red 19:Dark Green 18:Dark Red 17:White Frame 16:Scroll 15: and B zone 14:Color bar 13:1% Window 12:Ramp Blue 11:Ramp Green <Diagonosis> How to diagnose by using test pattern bnormal picture (icture Noise, Full Vertical Line,abnormal color) No picture Test pattern (4-20) Defective Block (Board) Test pattern Defective Block (Board) bnormal Display unit (D or C Board or anel) No picture Display unit (D or C Board or anel) Normal Tuner Box ( or DH Board) O.K Tuner Box ( or DH Board) <How to exit> Disconnect the C cord of the tuner box and display unit from the wall outlet. (To power off both tuner box and display unit is necessary.) 26

27 7. Important information (for TC-54Z1) 27

28 5.Important information (for TC-54Z1) WRNING Wall-mounting bracket [TC-54Z1] BCK COVER When installing a wall mounting bracket to the TC-54Z1 panel, DO NOT insert the mounting bolts more than 3/8 (10 mm) past the back cover. The panel will be damaged if the bolt is inserted more than 3/8 (10 mm) past the back cover. 8-10mm (5/16-3/8 ) REW However, the mounting screw must be at least 5/16 (8 mm) past the back cover to prevent unstable wall-mounting. Damages caused by improper wall-mounting procedures will not be covered under the warranty. NOTICE We recommend using anasonic s wall-mounting bracket, TY-WK51SW. To install anasonic s wall-mounting bracket (TY-WK51SW) : 1) Use the supplied llen wrench and mount the 4 llen head countersunk screws, 4 dish tooth washers, and 4 insulation spacers provided at the locations where the caps were attached, as shown in right figure. 2) Tightening torque: lb-ft (3 4 Nm). Rear view and proper screw setting llen wrench How to tighten the screws llen head countersunk screws dish tooth washers insulation spacers 28

29 5.Important information (for TC-54Z1) Handling (1/2) [TC-54Z1] There is No front glass by the front glass-less construction. 1. Wound on the surface of display panel By carefulless handling, there is the possibility that the wound and dirt attach to display surface. ay attention to panel when installation, transportation and movement. Handle with two persons! 2. Damage on the surface of display panel By impact, there is the possibility that display surface is damaged. Do not give impact on display surface. 29

30 5.Important information (for TC-54Z1) Handling (2/2) [TC-54Z1] Display unit, tuner box and speakers are in the same box. When opening box and taking out. 1. First, take display unit. 2. Next, take tuner box and speakers. If speakers and tuner box are taken first, display will fall down. First Display unit Speakers Tuner box 30

31 5.Important information (for TC-54Z1) Rear cover of this display unit is composed of 2 covers. Rear cover (Large) Raer cover [TC-54Z1] Number of rear cover depends on removing module. See the following table. Rear cover Module Remove the large rear cover only (with stand) Remove the large rear cover and small rear cover (with laying on a floor) <CB Location>,,, 2,,, C3,, B, GH, J, S, FN, C inlet NEL, GL, D,, K, SG Rear cover (small) (S) (MULTI) B (FILTER) C inlet When removing panel module, both of large and small rear covers and wall-mounting bracket, lay soft cloth, lay display unit on it and work. J GL D SG K S GH C3 2 31

32 5.Important information (for TC-54Z1) card slot for service [TC-54Z1] t the back of Display unit, there is card slot for service. Only for software version-up, this card slot is used. Slot only for service 32

33 5.Important information (for TC-54Z1) Service jig for module change [TC-54Z1] This jig is useful for standing and holding the D unit securely in the case of servicing. <Service jig> art No. Size Display Size Weight TZS07019 W : 28 (700mm), H : 38 (950mm), D : 24 (600mm) about 5 kg Only Service stand Service stand with display unit This is unusable for replacement of plasma panel and escutcheon. 33

34 5.Important information (for TC-54Z1) Service mode (1/3) Tuner box and display unit have their respective service mode. <Tuner box> 1. How to enter into Service Mode (Use RF Remote control.) While pressing VOLUME [ - ] button of tuner box, press [INFO] button of RF remote control 3 times within 2 seconds. Display screen (Blue background) Software version icture adjustment Option setting Service tool Monitor SERVICE DJUST OTION SRV-TOOL MONITOR STB eaks SOFT eaks EE eaks BOOT LSI DT STBY SOFT STBY EE STBY ROMCOR STBY2 SOFT STBY2 EE STBY2 ROMCOR Flash jax_ce RF RMC WiHD-GENX WiHD-RF WiHD-SI SERTE *.*** RB Cnt 000 *.*.* *.** *.**.** *.**.** *.**.** *.**.** *.**.** *.**.** *.**.** *.** *.*.* *.**.** *.**.** *.**.** **.**.**.**.** Key command 1 button --- Main items Selection in forward direction 2 button --- Main items Selection in reverse direction 3 button --- Sub items Selection in forward direction 4 button --- Sub items Selection in reverse direction VOL button --- Value of sub items change in forward direction (+), in reverse direction (-). 2. How to exit : Disconnect the C cord of tuner box and display unit from the wall outlet. 34

35 5.Important information (for TC-54Z1) Service mode (2/3) <Display unit> Only tuner box has a receiver for RF remote control. The function to switch to the service mode of display unit is added to that of tuner box so that RF remote control is available to use service mode of display unit. 1. How to enter into Service Mode (Use RF Remote control.) 1) While pressing VOLUME [ - ] button of tuner box, press [INFO] button of RF remote control 3 times within 2 seconds. Service mode of tuner box is displayed. (Blue background) 2) By 1 or 2 button, select [MONITOR] and press [OK] button. 3) [MONITOR MODE] will be displayed on the left-top of the screen and switch to service mode of display unit is completed. 4) While pressing VOLUME [ - ] button of display unit, press [INFO] button of RF remote control 3 times within 2 seconds. Service mode of display unit is displayed. (Green background) Display screen (Blue background) MONITOR DYNMIC MONITOR MODE Display screen (Green background) MONITOR MODE 1,2 : MIN SELECT 9 : ICTURE MENU SELECT OK : ENTER ress [OK] button on RF remote contrrol MONITOR MODE continues to be displayed on the left-top 2. How to exit : Disconnect the C cord of the tuner box and display unit from the wall outlet. (To power off both tuner box and display unit is necessary.) 35

36 5.Important information (for TC-54Z1) Service mode (3/3) <Display unit (Single mode)> IR remote receiver is installed in display unit. Service mode of display unit can be displayed by using IR remote control. 1. How to enter into Service Mode (Use IR Remote control) While pressing VOLUME [ - ] button of display unit, press [INFO] button of IR remote control 3 times within 2 seconds. Service mode of display unit is displayed. (Green background) Display screen (Green background) SERVICE MONITOR STND LONE DJUST eaks SOFT *.*** OTION 1 ** WB-DJ eaks EE *.*.* OTION 2 ** OTION eaks BOOT *.** OTION 3 ** GING LSI DT *.**.** Model ID ** SRV-TOOL STBY SOFT STBY EE STBY ROMCOR *.**.** *.**.** *.**.** RB Cnt ******** ******** 000 D SOFT D EE D FG D DROM **.** **.** **.** **.** WiHD-GENX WiHD-RF WiHD-SI *.**.** *.**.** **.**.**.**.** STND LONE MONITOR MODE is NOT displayed on the left-top of the screen. 2. How to exit : Disconnect the C cord of display unit from the wall outlet. 36

37 5.Important information (for TC-54Z1) <Tuner Box> Use RF Remote control. 1. How to access 2. Screen display & Check oint Display screen (Blue background) Self Check (1/2) [TC-54Z1] Self check indication only: ress volume [ - ] button of tuner box and [OK] button of RF remote control at the same time for more than 3 seconds. Self check indication and factory shipping setting: ress volume [ - ] button of tuner box and [MENU] button of RF remote control at the same time for more than 3 seconds. Confirm the following parts if NG was displayed. Display EKS TUN1 TUN2 FE VSW DV DV GenX MEM1 MEM2 MEM3 TEM GC6 Genx2 KYOTO HDMITx RERMC Ref.No. IC8001 TU8300 TU8300 IC8300 IC3001 IC4510 IC4510 I100 I101 IC8502 I501 IC4701 IC5100 I500 IC9005 IC9004 IC How to exit : Disconnect the C cord of display unit from the wall outlet. Description eaks VC TUNER (LL block) TUNER (MTS block) FRONT END ROCEOR UDIO/VIDEO SW DV7471(DV7496) V7471(DV4622 SYSTEM MOU EEROM (SYSTEM MU) EEROM (eaks) EEROM (CEC) TEM SENSR GC6 SYSTEM MU CEC KYOTO HDMI Tx RF REMOTE CONTROL.C.B -Board -Board -Board -Board -Board -Board -Board -Board -Board -Board -Board -Board -Board -Board DH-Board DH-Board RM-Board 37

38 5.Important information (for TC-54Z1) <Display unit> Use RF Remote control. Self Check (2/2) [TC-54Z1] 1. How to access Self check indication only: ress volume [ - ] button of tuner box and [OK] button of RF remote control at the same time for more than 3 seconds. Self check indication and factory shipping setting: ress volume [ - ] button of tuner box and [MENU] button of RF remote control at the same time for more than 3 seconds. 2. Screen display & Check oint Confirm the following parts if NG was displayed. Display screen (Green background) [fter setting to Monitor Mode (lease refer to page 35. ) ] Display DV DV GenX MEM1 MEM2 NEL TEM GC6 Ref.No. I4510 I4510 I1100 I1101 I8502 I9003 I1000 I5100 Description DV7471(DV7496) DV7471(DV4622) SYSTEM MU EEROM (SYSTEM MU) EEROM (eaks) NEL MICOM TEM SENSOR GC6.C.B D-Board D-Board D-Board D-Board D-Board D-Board D-Board D-Board When there is picture problem, information from tuner unit is not displayed. t that time, by using IR remote control, self check of display unit can be done. By IR Remote control (Display unit unique mode): ress volume [-] button of display unit and [OK] or [MENU] button of IR remote control at the same time, then self check (green color) is displayed. (MONITOR is not shown at left top.) 3. How to exit : Disconnect the C cord of display unit from the wall outlet. 38

39 5.Important information (for TC-54Z1) recautions for Wireless Unit <Transmission Range> Use the Wireless Unit (Transmitter) within a straight line distance of 10 m (approx.) from the Wireless Unit (Receiver). The range may be shortened if there are any obstacles or the surrounding environment or building structure affects the transmission. Side View 5 40 The angle of the transmitter can be adjusted to 40º upward and 5º downward. 5 m Display 45 Transmitter Receiver Floor 45 5 m [Vertical Direction] Top View Transmitter approx. 10 m 10 m <DO not install the following places> High temperature location (near the heater etc) oor air circulation place (at the end of a closed rack etc) 5 m m Receiver Display [Horizontal Direction] 39

40 5.Important information (for TC-54Z1) <When the wireless connection becomes off> Connection error (Wireless unit) When the wireless connection between transmitter and receiver becomes OFF, error message (like below) will appear. Check the connection between transmitter and receiver. No signal from the tuner box. lease check the connection of both wireless units. lso,please make sure the wireless transmitter and receiver are directly facing each other and no object is blocking their communication path. Receiver Transmitter 40

41 5.Important information (for TC-54Z1) Troubleshooting (Wireless unit) [1/2] <When Full HD wireless unit is connected> This is the flow for troubleshooting of wireless unit. icture or sound problem TX : Transmitter module of wireless unit RX : Receiver module of wireless unit Transmitter side LED of TX/RX is green. No Check (1)Self diagnosis (LED blinks) [Next page] Yes Change HDMI cable, it becomes normal. No Set is troubled. erform self diagnosis function of set. Receiver side Yes Wireless unit is troubled. (Troubles example) TX, RX module 41

42 5.Important information (for TC-54Z1) Troubleshooting (Wireless unit) [2/2] <Self check for wireless unit> TX : Transmitter module of wireless unit Transmitter side RX : Receiver module of wireless unit LED Green ON Orange ON Red ON Red Blinks 2 times Red Blinks 11 times Receiver side LED Green ON Orange ON Red ON Red blinks 11 times Status Radio wave condition is Good. (Normal condition) Radio wave condition is bad. HDMI is not connected. airing failure Fan problem Status Radio wave condition is Good. (Normal condition) Radio wave condition is bad. HDMI is not connected. Fan problem Trouble example Check environment of equipments TX/RX module Check environment of equipments TX/RX module TX/RX module Fan (TX side) Trouble example Check environment of equipments TX/RX module Check environment of equipments TX/RX module Fan (RX side) 42

43 5.Important information (for TC-54Z1) RF remote control registration [1/3] <First registration after purchase> To have Z1 model work, registration of RF remote control to the tuner box is required. [ How to register ] Fig.1 1. fter power-on, a registration screen is displayed. (Fig.1) 2. ress [MENU] key on the tuner box. 3. ress the [OK] button and the [1] button on RF remote control simultaneously for at least 3 seconds. (Fig.2) Note that registration may take 30 seconds. 4. When a screen of [Remote control registration completed] is displayed, press [OK] button and proceed to the next setting (Easy installation setting). (Fig.3) Fig.2 [1] button lease have your remote control ready with batteries installed. Continue? [OK] button The maximum numbers of RF remote controls to be registered is five. -When registering an additional RF remote control exceeding five, to erase all the RF remote controls which were already registered is required. -When erasing an RF remote control to be registered, all the registered ones are erased. -Erasing only one to be registered is not allowed. Fig.3 Remote control registration completed successfully. ress OK. OK 43

44 5.Important information (for TC-54Z1) RF remote control registration [2/3] <dditional registration> dditional RF remote control registration is required to start to use a new RF remote control because of failure etc. Display Remote control registration by pressing MENU key of the tuner box for 5 seconds. [ How to register ] 1. Select [Setup] by VOL [+] key of a tuner box and press [MENU] key. 2. [Remote control registration] should be selected. ress [MENU] key. 3. ress [MENU] key of a tuner box. 4. ress [OK] button and [1] button simultaneously for at least 3 seconds. Note that registration may take 30 seconds. 5. When a screen of [registration completed] is displayed, press [Return] button to finish registration. If you fail in a remote control registration 1. ower on the tuner box again (C lug in again or press [OWER] button for at least 5 seconds) and press [MENU] key on the tuner box for 5 seconds. 2.Then, please register again. If an old battery is used, remote control registration would be unsuccessful. lease use a new battery. 44

45 5.Important information (for TC-54Z1) RF remote control registration [3/3] <RF remote control Usage Notes > VIER Link buttons Because this remote control is RF remote control, it cannot send remote control code directly to DIG like a conventional IR remote control. VIER Link buttons on RF remote control is effective only when VIER Link-compatible DIG is connected with HDMI. TV operation keys on DIG remote control TV operation keys on a DIG remote control, which is based on IR method, are effective without registration to the tuner unit. receiver for IR remote control is placed on a display unit. lease point DIG remote control at the display unit and operate. recautions for RF remote control To prevent bad influence by interference of microwaves, use RF remote control keeping it away from the following equipments. Microwave oven, Wireless LN equipment, Bluetooth-compatible equipment Equipments which use microwave of 2.4GHz band (Digital cordless phone, Wireless audio equipment, Game machine, ersonal computer peripherals) 45

46 5.Important information (for TC-54Z1) Exchange of the modules <Exchange of TX/RX module and RF remote control module> TX : Transmitter module of wireless unit RX : Transmitter module of wireless unit In TX module, RF remote control module is included. When TX and RX are exchanged, RF remote control is also changed. So, when they are exchanged, pairing becomes off and communication does not work. So, when RF remote control is operated, ON signal from TX to RX does not pass. So, to solve it, re-pairing is necessary. Wireless unit TX (Transmitter module) WT WiHD Transmitter WH WiHD Host RM RF module Wireless unit RX (receiver module) RM WR WiHD Receiver RF module [ How to re-pairing ] 1. fter exchanging TX and RX modules were exchanged, connect TX and RX to tuner unit and display unit, respectively. 2. ower tuner unit ON by the power button. ower display unit ON by the power button. TX and RX becomes ON. 3. Between TX and RX, HDMI connection is established. HDMI picture appears. 4. When HDMI is connected, re-pairing between TX and RX modules are done, automatically. 46