VIDEO WALL INSTALLATION GUIDE TEL: WWW. ELECTROSONIC.CO.ZA

Size: px

Start display at page:

Download "VIDEO WALL INSTALLATION GUIDE TEL: WWW. ELECTROSONIC.CO.ZA"

Coleen Merritt
5 years ago
Views:

VIDEO WALL INSTALLATION GUIDE TEL: +27 11 770 9800

1 VIDEO WALL INSTALLATION GUIDE TEL: WWW. ELECTROSONIC.CO.ZA

Read this Important Information first before installing ProSpectre Video Wall displays Thank you for purchasing a ProSpectre Advanced Display product.

2 Read this Important Information first before installing ProSpectre Video Wall displays Thank you for purchasing a ProSpectre Advanced Display product. To ensure satisfactory results from your ProSpectre display, please take note of the following warning signs. WARNING Because of the nature of video wall screen aesthetics, very little bezel support is offered. PLEASE NOTE: Because of the architecture of LCD technology bezels are ultra-narrow. The LCD screen in front is only supported by the thin bezels that surrounds it. The light source is at the back and the light cannot be obstructed by any object. Thus the wiring for the LCD panel is very thin and embedded in the already thin bezel. The LCD screen and bezel is easily damaged due to incorrect handling! HANDLE WITH CARE: Do not place the ProSpectre screen on the floor without polystyrene support below! Do not tilt the screen forward whilst the screen is resting on the bezel! Do not lift the screen by the bezel. ONLY use the handles attached to the back frame! When aligned, no two screens should touch each other! There has to be a ventilation gap that can be checked by sliding a piece of paper unobstructed through the spacing between two adjacent screens. NOTE The manufacturer assumes no responsibility for any damage that is caused by incorrect handling and installation.

3 VIDEO WALL PACKAGE 1 - VIDEO WALL PANEL

4 VIDEO WALL PACKAGE 2 - WALL MOUNTS

5 VIDEO WALL PACKAGE 2.1 UNIT A Will be installed to the back side of the video wall panels 2.2 UNIT B Will be installed on to the wall or metal construction WALL MOUNT UNIT-A WALL MOUNT UNIT-B

6 VIDEO WALL PACKAGE MOUNTING UNIT - A Wall mount Unit A should be installed back side of the video wall panel with 4 MB screws as shown in the figure below

7 VIDEO WALL PACKAGE MOUNTING UNIT - A

8 VIDEO WALL PACKAGE MOUNTING UNIT - B Unit - B should be mounted to on a wall or metal construction as shown in the figure below.

9 MOUNTING PANEL + UNIT A TO UNIT B PANEL + UNIT A + UNIT B

10 PANEL + UNIT A + UNIT B

11 VIDEO WALL SAMPLE INSTALLATION (3 X 3)

12 SAMPLE INSTALLATION ( 3 X 3 ) STEP 1 - ALL WALL MOUNT UNITS SHOULD BE MOUNTED ON A WALL OR METAL CONSTRUCTION AS SHOWN IN FIGURE BELOW 55 VIDEO WALL HORIZONTAL DIMENSION = 1215 mm 55 VIDEO WALL VERTICAL DIMENSION = 687 mm 49 VIDEO WALL HORIZONTAL DIMENSION = 1080 mm 49 VIDEO WALL VERTICAL DIMENSION = 610 mm

13 SAMPLE INSTALLATION ( 3 X 3 ) STEP 2- PLACE AND FIX THE HDMI, REMOTE CONTROLLER AND POWER CABLES DETAILED CABLE INSTALLATION IS EXPLAINED IN THE NEXT TWO PAGES

14 PANEL CABLE SOCKETS

15 PANEL CABLES SETTINGS REMOTE CONTROL UNIT INSTALLATION SAMPLE INSTALLATION ( 3 X 3 )

16 PANEL CABLES SETTINGS HDMI CABLE SETTINGS, FROM SPLITTER TO PANELS. SAMPLE INSTALLATION ( 3 X 3 )

17 PANEL CABLES SETTINGS POWER CABLE SETTINGS, FROM POWER BOX TO UNIT. SAMPLE INSTALLATION ( 3 X 3 )

18 STEP-3 MOUNT THE PANELS

19 After mounting, panels should be set to maintenance mode.

20 SAMPLE INSTALLATION ( 3 X 3 ) AFTER MOUNTING THE TOP LINE, ALL THE PANELS OF THE TOP LINE SHOULD BE SET TO MAINTENANCE MODE. TOP LINE MAINTANENCE MODE. MIDDLE LINE BOTTOM LINE

21 SAMPLE INSTALLATION ( 3 X 3 ) STEP - 4 MECHANICAL ADJUSTING OF THE SYSTEM HOW TO ADJUST THE PANEL S DEPTH, HORIZONTAL AND VERTICAL SEETING S ARE EXPLAINED IN NEXT PAGE

22 DEPTH, SETTING. VERTICAL, SETTING. HORIZONTAL, SETTING.

23 SAMPLE INSTALLATION ( 3 X 3 ) 1. ADJUST THE REFERENCE PANEL PARALLEL TO THE GROUND. 2. THE BOTTOM LINE S HORIZONTAL, DEPTH, VERTICAL POSITION SHOULD BE ADJUSTED ACCORDING TO THE REFERENCE PANEL. 3. THE RIGHT VERTICAL LINE S HORIZONTAL, VERTICAL, DEPTH POSITION SHOULD BE ADJUSTED ACCORDING TO THE REFERENCE PANEL. 4. ADJUST THE REST OF THE SYSTEM WITH REFERENCE OF BOTTOM AND RIGHT LINE.

24 SOFTWARE ADJUSTMENT

25 SOFTWARE ADJUSTMENT 3X3 VIDEO WALL SOFTWARE ADJUSTMENT ENTER MENU MENU > SETTINGS > OTHER SETTINGS > VIDEO WALL SETTINGS > ROW COUNT : 3 ( IF THERE ARE 3 ROW ) > COLUMN COUNT : 3 ( IF THERE ARE 3 COLUMN ) > CELL : ( WICH SCREEN NUMBER )

26 MAINTENANCE

27 MAINTENANCE REMOVING SPECIFIED SCREEN FROM THE SYSTEM IF PANEL 5 REMOVED FROM THE SYSTEM FOLLOW THE STEPS BELOW. STEP 1 : 3. AND 6. PANEL MOVE TO RIGHT. STEP 2 : 1. AND 4.PANEL MOVE TO LEFT. STEP 3 : 2. PANEL MUST BE MAINTENANCE MODE. STEP 4 : REMOVING SPECIFIED PANEL FROM THE SYSTEM

28 MAINTENANCE

29 Tel: Address: 33 Lily Avenue, Northcliff, Johannesburg, South Africa, 2195

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width

SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system