!! ONLY USE TLD+ Zoom Lenses!!

Size: px

Start display at page:

Download "!! ONLY USE TLD+ Zoom Lenses!!"

Stuart Singleton
5 years ago
Views:

UDX Quick Start Guide Download Product Manual Product manuals and documentation are available online at www.barco.

1 UDX Quick Start Guide Download Product Manual Product manuals and documentation are available online at Registration may be required; follow the instructions given on the website. IMPORTANT! Read Installation Instructions before connecting equipment to the mains power supply. Install Lens!! ONLY USE TLD+ Zoom Lenses!!. Place the primary lens lock in unlock position. Handle (ref. ) towards electrical socket (ref. ).. If present remove the plastic protection cover from the lens holder opening.. Check if the secondary lens lock stands in the unlock position (ref. ).. Gently insert the lens. Ensure the lens connector matches the electrical socket on the lens holder.. Insert the lens until the connector seats into the socket. - The secondary lens lock (ref. ) makes an audible clicking sound when latching. - Do not release the lens yet, keep pushing the lens against the front plate!. Secure the lens in the lens holder by sliding the primary lens lock handle into the locked position.. Check if the lens touches the front plate of the Lens Holder.. Check if the lens is really secured by trying to pull the lens out of the lens holder. Connect power Ensure that the power is properly connected to the power input. (0-0V* / 00-0V [+/-0%, * reduced light output] ) R0 /0

2 Startup. Power on. Turn the mains switch to on ( I ). - Start up sequence starts. Backlight of the Power on/off button flashes WHITE. - When start up sequence is finalized the Power on/off button lit WHITE.. Press the Power on/off button. - The backlight of the Power on/off button changes from WHITE to BLUE. - Local LCD displays a start up screen. Adjust. Adjust the lens settings by pressing the LENS button or via the direct lens keys on the RCU. Select the Greenfocus test pattern to adjust the lens. TIP: Press star button (*) to activate test pattern. Orientation of the unit is set as standard in table front projection mode. Change the projector set up in the ALIGNMENT > ORIENTATION menu.. For Advanced adustments like Warping, Light management, etc. see User Guide of the projector. Connect and Select source. Connect available sources to the appropriate input ports.. Select connected source: Image of selected input appears. - The LED of the selected source lit up GREEN. - The yellow LED indicates if sync/signal is present. --

3 Switch off. Press the Power on/off button for three seconds.. Wait until the after-cooling cycle is finished (approximately 0 sec.). Turn the mains switch to off ( 0 ).. Unplug the power cord from the projector. s Precautions 0 s Remove the lens before transporting the projector. First switch the projector to Standby mode and wait until After Cooling is finished to switch off the main power. Ensure the projector is operating with clean filters. Do not block the ventilation in and outlets. External laser light can cause severe damage to the DMD. This damage is not covered by warranty. Local Keypad -- Menu Navigation. Menu Selection. Open Menu. Menu Back. Power On/. OSD On/. Input Selection. Shutter Open/Close. Test Patterns. 0 Lens Menu. Touch Panel. 0

4 RCU buttons Button pressed indicator. Shutter Open. Shutter Close. Touch Panel On/. LCD On/. Lens Zoom. Lens Shift. Menu Activation. Menu Selection. 0 Menu Navigation. Input Selection. Address button. Numeric buttons. Backspace XLR connector. Dot. Macro button. Menu Back. Default button. 0 Lens Focus. Color On/. Test Patterns. Power On. Power. Stereo Jack. RCU On/.

5 Communication Panel 0 WiFi antenna for wireless IP (optional) V A output Firmware update/usb backup custom settings 0 Sync In D Status lights 0/00 base-t for external control over IP and Art-Net DMX interface input DMX interface output IR receive sensor GSM antenna input (optional) XLR input for wired projector control RS for serial communication Sync Out D Venues & Hospitality Input (V&H) SDI IN SDI IN/OUT A C B DP D HDMI HDBT HDBT Quad G SDI channel A Input DisplayPort Input Quad G SDI channel B Input HDMI Input Quad G SDI channel C Input/Output HDBaseT Input Quad G SDI channel D Input/Output HDBaseT Input Virtual & Augmented Reality Input (V&AR) (Optional) DP A -- DP B DP C DP D Quad DisplayPort channel A Input Quad DisplayPort channel C Input Quad DisplayPort channel B Input Quad DisplayPort channel D Input

Button Backlight Status Button Power button Shutter button Color status Blinking WHITE Solid WHITE Description Projector starts up (Booting) Blinking RED Projector is in Standby Error condition

6 Button Backlight Status Button Power button Shutter button Color status Blinking WHITE Solid WHITE Description Projector starts up (Booting) Blinking RED Projector is in Standby Error condition Blinking BLUE Projector goes to ON mode Solid BLUE Projector not in power ON state Solid WHITE Shutter is open Solid RED Shutter is closed Projector is ON -- LED Status LED Color status Description PWR (power LED) RED Projector is in Standby ORANGE GREEN LIGHT (Illumination LED) ERR (error LED) IR RED Projector is Ready Projector is on ORANGE Light source is off Light source not detected Light source is on in ECO mode GREEN Light source is on in normal mode GREEN-ORANGE Light source is on in CLO mode No error RED toggles on/off Error ORANGE toggles on/off RED IR signal received GREEN IR signal acknowledged Support Website -- Projector powers up Warning Tel.: - USA + - EMEA APAC + 00

HDX 4K. Quick Start Guide. Connect power. Download Product Manual

HDX 4K. Quick Start Guide. Connect power. Download Product Manual HDX K Quick Start Guide Download Product Manual Product manuals and documentation are available online at www.barco.com/td/r000 Registration may be required; follow the instructions given on the website.