Hardware installation
|
|
- Maximillian Cain
- 5 years ago
- Views:
Transcription
1 Hardware installation 5. Place and fix the OMT to the interface without tightening the screws. Figure 291: Place and fix the OMT to the interface Note: Take care to place the OMT with the engraved ARROW indicating the pipe towards the pipe itself. 358 MPR-e
2 Installation Figure 292: Engraved arrow toward pipe 6. Install the MPT-HC V2/MPT-XP transceivers on the RF OMT. Note: Silicone grease must be put on the nose adapter O-ring when indicated in the manufacturer s installation instructions. If grease for O-ring is not mentioned, it must be avoided. MPR-e 359
3 Hardware installation Figure 293: Apply silicone grease Grasp the MPT-HC V2/MPT-XP by the handle and fasten it to the OMT with the four locking hooks that will be tightened onto the corresponding fastening brackets on the OMT. 360 MPR-e
4 Installation Figure 294: Locking hooks and fastening brackets Fine tuning procedure for polarization alignment The OMT to interface fixation screws must be tightened once the OMT body is in precise vertical position respect to the ground. Then, the antenna pointing procedure must be performed. It consists in finding the best antenna position to minimize the contra-polar received signal, acting on the pole mount tuning screws. After the antenna pointing procedure is completed, you need to apply the fine tuning procedure to one of the facing antennas to align the polarizations. Use the receiver on the polarization opposed to the transmitter on the facing antenna.to perform the fine tuning: 1. Switch to the cross polar receiver. 2. Slightly loosen the OMT to interface fixation screws. 3. Monitor the received cross polar signal and act on the special HEX spacer of the fine tuning mechanism of the OMT till the received signal power reaches its minimum (Power XP 30dB below the homopolar received signal). MPR-e 361
5 Hardware installation Figure 295: Fine tuning 4. Tighten the OMT fixing screws. Cable connections (MPT-HC V2/MPT-XP/9558HC) Electrical Ethernet cable If the PFoE has been implemented, only one cable interconnects the MPT-HC V2MPT-XP/ 9558HC with the Power Injector or MPT Extended Power Unit. To terminate the Ethernet cable (MPT-HC V2/MPT-MC/MPT-XP/9558HC side) and to pull it up from Indoor to MPT-HC V2/MPT-MC/MPT-XP/9558HC Warning: to make sure of the continuity and avoid short circuit, all cables / connectors connections such as RJ45, Coaxial, Ethernet, or Optical Fiber made on the field have to be verified and checked with Cable tester. The waterproofness must be also checked. To terminate the cable the kit plug R2CT must be used. The kit is made up of 10 items as shown in Figure MPR-e
6 Installation Figure 296: Kit plug R2CT Figure 297: Kit plug R2CT items Mating sequence instructions To terminate and to connect the cable to the MPT-MC follow the instructions: 1. Turn and remove the protection cap. MPR-e 363
7 Hardware installation Figure 298: Remove the protection cap 2. Partially unscrew the nut spiral. Figure 299: Unscrew the nut spiral 3. Pass the cable through the mini kit plug and crimp the RJ-45 plug according to the standard. Figure 300: Pass cable through the mini kit plug 364 MPR-e
8 Installation Figure 301: Crimp the RJ-45 plug Terminate the Ethernet cable according to the EIA/TIA 568B standard. Follow the instructions included with the connector. Figure 302: EIA/TIA standard 4. Insert the RJ-45 plug inside the unlocking clip NOTE: MPR-E doc says locking clip here--should probably be unlocking clip, judging by next step. Verify that the latch mechanisms are on the same side. Figure 303: Insert the RJ-45 plug in the unlocking clip MPR-e 365
9 Hardware installation 5. Pull the cable and insert the unlocking clip together with the RJ-45 plug inside the body, with the latches aligned with the body bayonet pin. Place the body arm on the left side. Figure 304: Insert the unlocking clip 6. If you need to hoist the assembly, pull the coupling nut to cover the plug body and return the protection cap. Figure 305: Pull the coupling nut 366 MPR-e
10 Installation Figure 306: Return the cap 7. Tighten the nut spiral with a 21 mm wrench with a torque of 3 N.m mini and 3.5 N.m maxi. The cable is now attached to the plug and ready to be pulled. Figure 307: Tighten the nut spiral Figure 308: Cable is ready to be pulled MPR-e 367
11 Hardware installation 8. Install the cable, partially unscrew the nut spiral and remove the protection cap to connect to the receptacle. 9. Align the two marks on the plug body and the receptacle, insert the plug body into the receptacle and rotate it clockwise. Figure 309: Align, insert and rotate the plug body 10. Connect the RJ-45 plug to its socket by pushing the cable. Figure 310: Connect the RJ-45 plug to its socket 11. Push the coupling nut and rotate it clockwise until it is secured to the receptacle. 368 MPR-e
12 Installation Figure 311: Push and rotate the coupling nut 12. Secure the assembly by screwing the nut spiral with a 21mm wrench with a torque of 3 N.m mini and 3.5 N.m maxi. Figure 312: Secure the assembly Unmating sequence instructions To perform the unmating sequence: 1. Unscrew the nut spiral using a 21 mm adapted wrench. Figure 313: Unscrew the nut spiral MPR-e 369
13 Hardware installation 2. Rotate and unlock the coupling nut. Figure 314: Rotate and unlock the coupling nut 3. Engage the RJ-45 unlocking clip forward until it stops. Figure 315: Engage the RJ-45 unlocking clip 4. Press on the unlocking clip latch. Figure 316: Press on the unlocking clip latch 5. Pull the clip and the cable rearward to disconnect the RJ-45 plug. 370 MPR-e
14 Installation Figure 317: Disconnect the RJ-45 plug 6. Rotate and disconnect the R2CT plug body. Figure 318: Rotate and disconnect the R2CT plug body Optical cable connection An optical cable must be used, if the PFoE has not been implemented. Note: First the SFP must be inserted in the MPT. The SFP is not included in the MPT. The cable is shown in Figure 319. The cable is a preassembled cable available in different lengths; see Accessories and cables for MPT-HC V2/MPT-XP/9558HC connections. Figure 319: LC/Q-XCO to LC Fiber cord To pull-up the cable take a cord and insert it in the slot of the cable cap. Make a knot on the cord and pull-up the cable. MPR-e 371
15 Hardware installation Remove the cap and connect the connector to the LC+Q-XCO connector in the MPT-HC V2/MPT-XP/9558HC. The overlength of the optical fiber must be rolled up in the Cable overlength box. Fix the Fiber on the pole or the tower with UV tie raps. See Figure 320. Figure 320: Fiber cable overlength box For the 1+0 repeater configuration, LC/Q-XCO cable (3CC52169XXXX) is required for ODU-ODU connection. Power supply cable connection The power supply cable is a coaxial cable, which is used only if the optical cable is used to transport the Ethernet traffic. Two types of coaxial cables are available according to the length (less than 200 m or 200 m to 350 m). The coaxial cable must be connected to: Indoor side: to the Station battery through the Lightning protection + Low Pass Filter + Pigtail N-to-2 wires. See How to connect the MPT-HC V2 to the battery. ODU-side to the N-to-Ethernet pair pigtail (+ RJ45 + R2CT). The R2CT must be then connected to the relevant connector on the MPT-HC V2/MPT-XP/9558HC. For the termination of the cable with RJ45 and R2CT see Electrical Ethernet cable. 372 MPR-e
16 Installation Warning: The Power Supply connection must be made waterproof (see Type N connectors and grounding kits waterproofing on the IDU/ODU cables). Surround the connector with the auto amalgamate tape from up to down Surround the connector with the adhesive tape from up to down Put tie raps on the up and the down of the connector Cable connection in XPIC configuration The two MPT-HC V2/MPT-XP must be linked with the XPIC cable and with the RPS cable. The XPIC cable is a cat7 cable with proprietary connectors. Three lengths are available: 1 m, 2.5 m, 8 m, to be chosen depending on the way the MPT-HC V2/MPT-XP are installed. The RPS cable is an LC-LC optional jumper preassembled with Q-XCO (1m length). Figure 321: XPIC connector position MPR-e 373
SECTION 4 TABLE OF CONTENTS
Contents Introduction LC, SC and ST Series...4-2 Markets and Applications...4-2 International Standard Documents Compliance...4-2 LC Series Features and Benefits...4-3 LC Standard... 4-4 to 4-5 LC for
More informationHD Flex Patch Panel. ASSEMBLY VIEW (FLEX1UPN** shown) FS128B. CONTENTS: (#) indicates FLEX4UPN** quantity
HD Flex Patch Panel Part Numbers: FLEX1UPN**, FLEX2UPN**, FLEX4UPN** Panduit Corp. 2018 INSTALLATION INSTRUCTIONS Note: HD Flex Patch Panels are compatible with HD Flex Fiber System Components. HD Flex
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version October 5, 2016 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE TERMINAL...6
More informationFOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N
FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N In-line and butt version Cold applied re-usable fiber optic closure Contents 1 Introduction 1.1 Product description 1.2 Capacity 2 General
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More informationOptical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
More informationUser Manual CXE800. Fibre Optic Receiver. CXX Series. Teleste Corporation
Broadband Cable Networks August 30, 2007 1(8) CXX Series User Manual Teleste Corporation CXE800 Fibre Optic Receiver Broadband Cable Networks August 30, 2007 2(8) Introduction The CXE800 is a unidirectional,
More information3G-SDI Fiber Optic Digital Extension Modules in 19 1RU Frame
WWW.OPTICIS.COM 3G-SDI Fiber Optic Digital Extension Modules in 19 1RU Frame User s Manual (BR-300 / BR-310) Doc No. : OSE-SDI150102-BR300 / Rev1.2-1 - Contents Welcome!...- 3 - Product Description...-
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationCAT6 Cable Tester. Operating Manual. Part No TRIAX - your ultimate connection
CAT6 Cable Tester Part No. 157010 Operating Manual TRIAX - your ultimate connection Application For checking CAT 5e and CAT 6 cables, (UTP and STP). Can also be used with BNC coaxial cable and modular
More informationCoyote popup display set up instructions
Coyote popup display set up instructions Frame 1 2 3 Prepare frame for assembly by locating the purple hooks on top of the frame. Stretch frame to size, snapping magnetic locking arms together. Attach
More informationAerospace Fiber Optics
Aerospace Fiber Optics AFO 101, Session 2 Fiber Optic Assembly Everett Community College. All rights reserved. 1 Session Learning Objectives After completing this session you should be able to: Work safely
More informationProcedure: Procedures: DIME TEAM: Drop # (circle one) Date: In Lab (either on Level 4, Level 6, or in shop): Installation: Functional Check
Procedure: Red Experiment specific Black - General In Lab (either on Level 4, Level 6, or in shop): Installation: 1. Wear safety goggles when working with the experiment. 2. Perform experiment-specific
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version September 14, 2017 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws M4 x 14mm (x1) Silver
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: LPDA 200 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationIP-LINX. Installation Guide
Installation Guide Installation Guide, 146653-4 Copyright 2017, Telect, Inc. All Rights Reserved Telect and Connecting the Future are registered trademarks of Telect, Inc. 22425 East Appleway Ave. # 11
More informationMain Products. Cable Assemblies Wire Harnesses Raw Cables. Connectors
About BMA BMA technology Ltd was found in Hong Kong in 2009. Our factory is located in Guangdong, China. With the 10,000m 2 production area, we are able to hold 500 workers during the peak season. Our
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationUser Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation CXE810. Fibre optic receiver
27.3.2012 1(12) CXX Series User Manual Teleste Corporation CXE810 Fibre optic receiver 27.3.2012 2(12) Contents Introduction... 3 Installation... 3 Housing... 3 Powering... 4 Interfaces... 4 Fibre installation...
More informationEC Series Creativity Accessories Safety and Installation Guide
EC Series Creativity Accessories Safety and Installation Guide Safety precautions Warning! Before installing Martin EC Series video panels using the accessories described in this guide, read the Safety
More informationAssembly instructions
Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0)1553 811000 Email: support@maxview.co.uk Web: www.maxview.co.uk Maxview reserve the right to change specifications
More informationToughsat Flyaway Users Manual
Toughsat Flyaway Users Manual TOUGHSAT FLYAWAY USERS MANUAL V.1.6 September 2012 Important warning regarding your TOUGHSAT System All power to the system (controller, modem, external network devices) MUST
More informationFIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
More informationHYPERLINE UTP/STP Cable Strippers and Cutters
198 HYPERLINE UTP/STP Cable Strippers and Cutters UTP/STP Cable Stripper and Cutter, type 110 HT-318 UTP/STP Cable Stripper and Cutter HT-501 Ordering HT-318 HYPERLINE UTP/STP Cable Stripper and Cutter,
More informationHC20 Healthcare Kit Installation Instructions
Our HC20 installation kit uses technology that allows a standard hospital pillow speaker to control a TV and receive audio from the TV at the pillow speaker next to the patient. The HC20 product, when
More informationVHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies
VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF: 54-216 MHz UHF: 470-698 MHz FM: 87.9-107.9 MHz Voltage Input: AC110-120V / AC220-240V Working:
More information2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU
2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU 1 The 3613WDU Analog Temperature / RH Sensor Upgrade Kit is used to upgrade Watchdog 2000 Series Weather
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: MOD 550 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationAssembly Instructions
Assembly Instructions REP Series Environmentally - Sealed Rectangular Plastic Connectors Hypertac S.A. January 2014 Assembly Instructions REP Series January 2014 1 Table of Contents I. Introduction A.
More informationWaterVue TV Installation & User Manual
WaterVue TV Installation & User Manual 19 Waterproof TV Dimensions of TV Front screen 486mm x 340mm x 3mm Mounting Plate 467mm x 324mm x 48mm 24 Waterproof TV Dimensions of TV Front screen 576mm x 395mm
More informationA449-6S 70 CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-6S 70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951425 (7/93) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
More informationASSEMBLY AND INSTALLATION 3 ELEMENT 6 METER BEAM
ASSEMBLY AND INSTALLATION A50-3S 3 ELEMENT 6 METER BM COMMUNICATIONS ANTENNAS 951364 (12/94) WARNING THIS ANTENNA IS AN ELTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DTH, OR SERIOUS INJURY.
More informationHigh Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions
High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for
More informationFOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block
FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4
More informationChapter 4. Dish Antenna Installation. Installing a DISH 500 Antenna. Finding the Satellites
These instructions guide you through the installation of a satellite system which includes your receiver (included with this manual), and a DISH Pro DISH 500 antenna system that can be identified by the
More informationSUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702
SCF611S SUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702 SCF611S SUBCARRIER TRANSFER FILTER TABLE OF CONTENTS PAGE SHIPPING INSPECTION 2 MODULE CONFIGURATION 2 INSTALLING MODULES 2-3 CABLING 3 FRONT
More informationIP-LINX Fiber :: X-XXXX
Fiber :: 055-797X-XXXX User Manual Telect, Inc. All rights reserved. 146653-A0 Table of Contents Chapter 1: Introduction...3 1.1 Tools Required...3 1.2 Additional Parts...3 1.3 Assemblies...3 Chapter 2:
More informationPower Injector 1520 Series
Power Injector 1520 Series Technical Specifications Input voltage 100 to 240 VAC Output voltage 56.0 VDC Voltage range tolerance 54 VDC to 57 VDC Maximum current 1.43 A No load current 15 ma 56VDC@0.71A
More informationTKEY-K16. Touch CW automatic electronic keyer. (No moving parts no contacts) Assembly manual. Last review: March 15, 2018
TKEY-K16 Touch CW automatic electronic keyer (No moving parts no contacts) Assembly manual Last review: March 15, 2018 Commands and use manual of the K16 and Updates and news: www.ea3gcy.com Thanks for
More informationIn-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide
In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The
More informationTV Lift System Model CL-65 Installation Instructions
TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing
More informationCheck what you have received against the component checklist and hardware above.
SA46S SA46W SA46B SA46PB Component Checklist Installation Instructions SYSTEMA Systema Monitor Arm 460mm HARDWARE Display Mounting Spacers (x4) Display Mounting Screws Arm Assembly VESA monitor head M4
More informationPeak Atlas IT. RJ45 Network Cable Analyser Model UTP05. Designed and manufactured with pride in the UK. User Guide
GB05-7 Peak Atlas IT RJ45 Network Cable Analyser Model UTP05 Designed and manufactured with pride in the UK User Guide Peak Electronic Design Limited 2001/2013 In the interests of development, information
More informationCommon Public Radio Interface Fiber :: Telect HDX & ELF CPRI Panels and Modules
Overview Telect's HDX and ELF CPRI Interface Panels and Modules provide non-service affecting monitor ports to be installed between the Optical CPRI Base Band Unit (BBU) and the Remote Radio Head/ Active
More informationInstruction manual. Midi Fiber Dome. Instruction manual
Midi Fiber Dome Instruction manual Product contents: - 1x Midi Fiber Dome - 1x Window Cut port seal - 1x sealing rubber (long) - 4x sealing rubber (short) - 4x stainless steel screw 4 x 25 T20-6x dummies
More information1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM
REVISION G January 11, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1183 Az/El MOUNT ANTENNA SYSTEM G
More informationStructured Cabling Introduction & Installation Guide
Structured Cabling Introduction & Installation Guide Structured Cabling Overview General Structure - Cat5e/Cat6 Cabling The structure illustrated has the following key points: Face plates present outlet
More information12G Broadcast connectors
12G Broadcast connectors Delivering 12G in a single punch www.coax-connectors.com Welcome to COAX 12G BNC Plug return loss COAX Connectors Ltd is a leading UK designer, manufacturer and supplier of high
More informationINSTALLATION INSTRUCTIONS FOR
INSTALLATION INSTRUCTIONS FOR MODEL 2240LED www.sportablescoreboards.com 1 Table of Contents 8 X 7 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR
More information100Base-FX Multi-mode to 100Base-FX Single Mode Converter. NXF-708 Series User s Manual
100Base-FX Multi-mode to 100Base-FX Single Mode Converter NXF-708 Series User s Manual COPYRIGHT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
More informationA CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951424 (10/91) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DEATH
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More informationGigabit Multi-mode SX to Single Mode LX Converter. User s Manual NGF-728 Series. Warning COPYRIGHT
COPYRIGHT Gigabit Multi-mode SX to Single Mode LX Converter User s Manual NGF-728 Series All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
More information3M Fiber Optic Wall Mount Enclosure 8430 Series
3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Multiplexer Enclosure and Cabling December 00 Figure - Trase Unit and Multiplexer Enclosure BNC Coaxial Cables From s (in order) MULTIPLEXER MODEL: 00B R / / / / / / / 9 0 9 0 Multiplexer
More information18mm ECAM Cable Entry Port
18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters
More informationElectric Motorized Projection Screen PowerMax Tension Series
Electric Motorized Projection Screen PowerMax Tension Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen
More informationTen-Tec (865) Service Department:(865)
Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram
More informationMIL-C CLASS L COMPATIBILITY ORDERING INFORMATION
MIL-C-22992 CLASS L COMPATIBILITY ORDERING INFORMATION ORDERING INFORMATION: Connectors are supplied with removable contacts. Contacts are supplied unassembled. Also supplied are applicable accessories
More informationSUHNER QMA SUBMINIATURE CONNECTORS
SUHNER QMA SUBMINIATURE CONNECTORS Description Content Page SUHNER QMA coaxial connectors are available with 50 Ω impedance. The frequency range extends to 11 GHz, depending on the connector and cable
More informationFOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15
FOSC 400 Ordering Guide For Closures and Accessories Section I 3 How to Order FOSC 400 Closures Section II 5 How to Order Accessories for FOSC 400 Closures Section III 9 Other FOSC Fiber Optic Splice Closures
More informationQUICK INSTALLATION GUIDE
V1.1.1/2018 homeit.io All rights reserved Index NR. CHAPTER PAGE 1 Introduction 2 1.1 The homeit System 2 2 Equipment and materials 3 2.1 The homeit KIT 3 2.2 Tools & Supplies 4 3 Location of the homeit
More informationSnail Fence InteleCell Deployment Guide
Snail Fence InteleCell Deployment Guide Preparation 1. Prepare deployment trip by making sure you have the following materials and tools when you fly up to the site: InteleCell NEMA Enclsoure (grey plastic
More information75 Elliptical Antenna System
Instruction and Assembly Manual 75 Elliptical Antenna System 7291 NW 74th Street Miami, FL 33166 GlobeCast Technical Service: (888) 988-5288 Manufactured By: 2002 Channel Master LLC Printed in U.S.A. 8000915-02
More informationCaution. Hanging the Screen:
Installation Instructions for Laminar and Laminar XL Projection Screens Caution 1. Read Instructions through completely before proceeding; keep them for future reference. Follow these instructions carefully.
More informationSECTION 683 VIDEO OPTICAL TRANSCEIVER WITH BI-DIRECTIONAL DATA CHANNEL DESCRIPTION
683 SECTION 683 VIDEO OPTICAL TRANSCEIVER WITH BI-DIRECTIONAL DATA CHANNEL DESCRIPTION 683.01.01 GENERAL A. The Contractor shall furnish the designated quantity of Video Optical Transceiver (VOTR) pairs
More informationCOYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x cm cm x cm)
OCTOBER 2004 COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x 55.88 cm 21.59 cm x 55.88 cm) Be sure to read and completely understand this procedure before applying
More information3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions September 2017 78-8130-5055-2-M 2 September 2017 78-8130-5055-2-M 1.0 Kit Contents 2.0 General...
More informationStep 1. 2x Kep Nut 1x Left Motor Assembly
Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Steps 1 to 3 involve removing elements from the model. These elements will be reattached later. Parts to be Removed Step
More information3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR
3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The
More information2179-CD Series Fiber Optic Splice Closure. Installation Instructions
2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal
More informationLynx Broadband Installation Manual for Residential Packages with a 35 db Amp Quick Start Guide (first 3 pages)
Lynx Broadband Installation Manual for Residential Packages with a 35 db Amp Quick Start Guide (first 3 pages) 1. Be sure that your kit includes all the parts shown in the Check the Equipment section in
More informationSECTION TESTING, IDENTIFICATION AND ADMINISTRATION
PART 1 - GENERAL 1.1 SUMMARY SCOPE SECTION 25170 TESTING, IDENTIFICATION AND ADMINISTRATION 1. This section includes the minimum requirements for the testing, certification administration and identification
More informationTracVision 95W LNB Installation
TracVision 95W LNB Installation To enable a TracVision system to receive DIRECTV international programming from the linear satellite located at 95W, a 95W LNB must be installed in a secondary M7SK or M9
More informationGENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS. 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~)
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~) Xterra (2006~) 3. PART NUMBERS: XM Tuner Kit 999U9-AS003 SIRIUS Tuner Kit
More informationMT-RJ SECURE Product Expansion Now 10 Variants of the MT-RJ SECURE Products
MT-RJ Product Expansion Now 0 Variants of the MT-RJ Products In response to several customers, the MT-RJ product line has been expanded with an additional six color/key versions. In addition to the original
More informationUMN_ User Manual Antenna Simplex. TECHNO-MEDIA srl Via IV Novembre 92, Bollate (MB) tel
UMN_00094400 User Manual Antenna Simplex TECHNO-MEDIA srl Via IV Novembre 92, 20021 Bollate (MB) tel. 0248672988 - info@techno-media.it Aggiornamenti Revision N Date Owner Notes 1 02/03/2017 T-Media First
More information2100, 2200, 4100, 6200, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors
00, 00, 400, 600, MPB Series Side Mount Drive Package for Light Load 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box 0 975 Cottonwood
More informationInstallation. SAPTF33xx-1xx in the Network. Standard Configuration
SAPTF33xx-1xx in the Network Standard Configuration One Unit A device (SAPTF33xx-100) and one device () are required for the standard configuration. The Unit A device is connected to the while the device
More informationFTTH & FITH. Discreet optical fiber solutions from the network connection point to the set-top box.
FTTH & FITH Discreet optical fiber solutions from the network connection point to the set-top box www.omelcom.com FIBER: THE FUTURE IS HERE The past several years have seen major progress in the penetration
More informationData Sheet IP67 Mast Enclosure
Data Sheet IP67 Mast Enclosure Pre-assembled outdoor housing for mast mounting Features With the IP67 mast box, MICROSENS offers a pre-assembled, compact chassis which is ideally suited for the integration
More informationepos & Security Essentials Trade ONLY ONLY Trade Catalogue Call us Now on Visit Our Website
epos & Security Essentials Trade Catalogue Trade ONLY ONLY Call us Now on 024 7668 8590 Visit Our Website www.tronicextreme.co.uk 2 Item No. 10595 Item No. 10596 TP-101 All in One Touch Screen epos System
More informationDigital Active Outdoor DVB-T/T2 Antenna
Digital Active Outdoor DVB-T/T2 Antenna SRT ANT 45 Picture similar User Manual Manuel d utilisateur Bedienungsanleitung Istruzioni d uso Manual de usuario Manual do Usuário Bruksanvisning Bruger Manual
More informationSite Installation Model MP-8424
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationSite Installation Model MP-8433
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationVibratory Deck Sieves 15 in. (380 mm)
Instruction Sheet P/N 1604433-01 Vibratory Deck Sieves 15 in. (380 mm) Introduction This instruction sheet covers the vibratory deck sieves listed in the following tables. 15-Inch Deck Sieves with 2.5
More informationMedium Box for Cable Termination
FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling
More informationGENUINE PARTS. SIRIUS Under Glass Antenna Kit
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Pathfinder (2006-2007) 3. PART NUMBERS: XM Tuner Kit 999U9-AS005 SIRIUS Tuner Kit 999U9-AS006
More informationINSTALLATION INSTRUCTIONS FOR. MODEL 2230LED
INSTALLATION INSTRUCTIONS FOR MODEL 2230LED www.sportablescoreboards.com 1 Table of Contents MODEL 2230LED... 3 8 X 4 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:...
More informationCoyote popup features
Coyote popup features The Coyote popup display system combines strength, reliablility, and style in a lightweight and easy to use system. It is fully magnetic, making it simple to assemble and disassemble,
More information2000i. Projector Replacement Guide. for Projector Replacement Kits. NEC MT1060R ( ) and NEC MT860R ( ) Interactive Whiteboard
2000i Interactive Whiteboard Projector Replacement Guide for Projector Replacement Kits NEC MT1060R (03-00043) and NEC MT860R (03-00041) 99-00496-00 Rev A0 FCC Warning This equipment has been tested and
More informationStep 1. 1x NXT Ultrasonic Sensor
Start with the build completed in Lesson 3 of the TETRIX Getting Started Guide. Step 1 involves removing an element from the model. This element will be reattached later. Parts to be Removed Step 1 1x
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationChallenges. TETRIX Getting Started Guide STEM Challenge Building Guide. Step 1. Parts Needed. Tips
Note: The Arm and Gripper Extension has been recommended as an initial build to complete the STEM Challenge. The STEM Challenge Sample Program and Programming Guide have been created to work effectively
More information4320 SS-25 Self-Strip Terminating Block
4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 1.0 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for
More information