Instructions for DataMark PDF Temperature Logger
|
|
- Scott Walker
- 5 years ago
- Views:
Transcription
1 Instructions for DataMark PDF Temperature Logger DataMark provides a convenient way to obtain high accuracy temperature data in transit. The unit is a self contained temperature logger that plugs directly into the USB port of a PC computer. Starting DataMark is supplied in protective clear plastic sleeves that are sealed to protect the unit from moisture. To start, press three times on the START button by applying thumb pressure through the plastic sleeve. Each press of the button is confirmed by the each of the three LEDs coming on from bottom to top, as shown at right. You will have 10 seconds to perform this "1 2 3" operation to start the unit. If you change your mind, just wait and the start function resets after 10 seconds elapse. Each light stays lit when the startup sequence is keyed in. At the end of this sequence, the lights flash in "1 2 3" order as a final confirmation. Press #1 Bottom yellow LED Press #2 Middle Green LED added Stopping, Alert Indicators and Marking the Record When the STOP button is pressed, all the LEDs light up. Stopping recording requires the three sequential button presses. Each of the LEDs go out in reverse sequence: Top Red, Middle Green, and Bottom Yellow, in order. Press #3 Top Red LED added A single press of the STOP button will mark the record, but will not terminate the recording process. The LED indicators have very specific patterns that signal alert conditions. These patterns warn the user of potential alert conditions (over or under critical temperatures) for less than the specified duration, or excursions of temperature that exceed the criteria for the temperature threshold and the specified duration. A single press of the START button while the unit is running will activate the alert indicators to show the current status. These are "preset" in standard tags, but can be reset by your dealer or by the user. Instructions for user resetting of the alert parameters is shown in a later section in this user guide. On the following page, a chart describes all or the LED light patterns and how they signal particular conditions. 1
2 Reading the Alert LEDs Normal Green LED Flashing This pattern indicates that the logger is operating normally and that there have been no temperature excursions at all above or below the preset temperature values. Normal + High Alert Green and Red LEDs Flashing This pattern there has been at least one upper limit temperature excursion above the preset temperature limit value, but the indicated duration of this excursion has not exceeded the preset "time over temperature" value. High Alert Red LED Flashing This pattern indicates there has been at least one temperature excursion above the preset high temperature value and there has been a total "time over temperature" duration that exceeded the preset time value for the high temperature limit. Normal + Low Alert Green and Yellow LEDs Flashing This pattern that there has been at least one lower limit temperature excursion below the preset temperature limit value, but the indicated duration of this excursion has not exceeded the preset "time under temperature" value. Low Alert Yellow LED Flashing This pattern indicates there have been at least one temperature excursion below the preset low temperature value and has a total "time under temperature" duration that exceeded the preset time value for the low temperature limit. High and Low Alert Red and Yellow LEDs Flashing This pattern indicates that there have been at least one temperature excursion below the present low temperature value and at least one temperature excursion above the present high temperature value. In both cases, the "time over/undertemperature" durations have exceeded the preset time limits for both high and low settings. 2
3 Reading the Data on the Computer Installing the "Mini App" for DataMark DataMark requires installation of a very small software function. To obtain the software, click on the link supplied to your by the DataMark seller. Go to the download site recommended to you and hit enter. The message returned will vary with the type of browser you are using. All browsers will prompt you to Run or Save. ALWAYS SELECT SAVE. Save the file in a convenient folder. The program will create its own secure database in whatever folder you put the exe file. When you wish to run the program, just click on it and it will start up. Note that this program is not installed into the Windows environment. It just is loaded every time the exe file is clicked. This is entirely normal. For example, in Windows 7 you will get this message: Just click Run and the program will come up instantly. If you do not want to see this repeatedly, unclick the "Always ask" checkbox. There are different forms of this warning on different operating systems, but the process is the same. When the program opens, an icon for the secure database will appear. You will not be able to open the database...just ignore it and proceed with the program. Contact your dealer more details. 3
4 USB Configuration When you first plug in a DataMark unit, in most computers the installation for the driver will be automatic. In Windows 7, you will most likely not have a successful installation the first time. There is an easy fix for this...leave the unit plugged into the USB port and reboot your computer. Windows 7 will recognize the device and will then install the drivers. If you are have any difficulty, ask your dealer. User Configuration of DataMark Users can configure a DataMark to their own requirements. Although each DataMark as supplied in a sealed clear plastic sleeve, the un started DataMark can be removed and inserted into a USB port for setting of parameters. When this is done, the screen will show somewhat differently from the screen that is produced when reading a DataMark at the end of a temperature recording. It looks like this: Click here to customize the parameters for your application. Basic information from the inserted, unstarted DataMark is shown in the "Device Information" panel, including Serial Number, Alert parameters, logging interval and Start Delay. Note that the NOT STARTED message is displayed, as well. Selecting "Device Settings, as shown above, results in a dialog box that presents the user with data boxes to fill for the whole range of parameters: 4
5 All of the parameters that are shown with a "white box" above can be changed. The program will not allow impossible combinations. Sampling period (log interval) is internally calculated. If you change the Log duration parameter, the program will automatically select the interval that distributes the 5,000 available readings over that span of time. Device notes is a section that permits the user to enter data that is relevant to the shipment. This information is stored internally in the DataMark, and will be displayed later when and if the DataMark is downloaded. You will be prompted to remove the DataMark and then put it back into the USB port to record the changes. This takes a few seconds, and then the changes are recorded internally. 5
VIDEO GRABBER. DisplayPort. User Manual
VIDEO GRABBER DisplayPort User Manual Version Date Description Author 1.0 2016.03.02 New document MM 1.1 2016.11.02 Revised to match 1.5 device firmware version MM 1.2 2019.11.28 Drawings changes MM 2
More informationRemote Application Update for the RCM33xx
Remote Application Update for the RCM33xx AN418 The common method of remotely updating an embedded application is to write directly to parallel flash. This is a potentially dangerous operation because
More informationTransmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
More informationAuxiliary states devices
22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary
More informationYellow Frog. Manual Version 1.1
Yellow Frog Manual Version 1.1 1 YellowFrog Contents PC Requirements...... 2 YellowFrog Power Meter Measurement.... 3 YellowFrog PC Software..... 3 Main Screen....... 4 Input Overload....... 5 Battery
More informationVOB - data over Video Overlay Box
VOB - data over Video Overlay Box Real time data overlayed onto video, both PAL and NTSC versions available Real time lap and sector times without a track side optical beacon User configurable display,
More informationDVR-431 USB Wireless Receiver User Manual
DVR-431 USB Wireless Receiver User Manual Thank you for using our wireless USB receiver, please read the following content carefully before using, it will help you make better use of this product. Introduction
More informationD-901 PC SOFTWARE Version 3
INSTRUCTION MANUAL D-901 PC SOFTWARE Version 3 Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.
More informationHITS QT/QT+ Setup Instructions for QSD/QHD Services using: Drake SCT2x4 Headend Transcoder 2 Satellites/4 Multiplexes
HITS QT/QT+ Setup Instructions for QSD/QHD Services using: Drake SCT2x4 Headend Transcoder 2 Satellites/4 Multiplexes Drake Transcoder Front /Rear View Setup and Programming Instructions: Input Setup Below
More informationINTRODUCTION TO ENDNOTE
INTRODUCTION TO ENDNOTE What is it? EndNote is a bibliographic management tool that allows you to gather, organize, cite, and share research sources. This guide describes the desktop program; a web version
More informationAgilent MOI for HDMI 1.4b Cable Assembly Test Revision Jul 2012
Revision 1.11 19-Jul 2012 Agilent Method of Implementation (MOI) for HDMI 1.4b Cable Assembly Test Using Agilent E5071C ENA Network Analyzer Option TDR 1 Table of Contents 1. Modification Record... 4 2.
More informationTraining Note TR-06RD. Schedules. Schedule types
Schedules General operation of the DT80 data loggers centres on scheduling. Schedules determine when various processes are to occur, and can be triggered by the real time clock, by digital or counter events,
More informationLaboratory 9 Digital Circuits: Flip Flops, One-Shot, Shift Register, Ripple Counter
page 1 of 5 Digital Circuits: Flip Flops, One-Shot, Shift Register, Ripple Counter Introduction In this lab, you will learn about the behavior of the D flip-flop, by employing it in 3 classic circuits:
More informationFord AMS Test Bench Operating Instructions
THE FORD METER BOX COMPANY, INC. ISO 9001:2008 10002505 AMS Test Bench 09/2013 Ford AMS Test Bench Operating Instructions The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana,
More informationEndNote Basic: Organize your references and create bibliographies Creating Your EndNote Basic Account
EndNote Basic: Organize your references and create bibliographies Creating Your EndNote Basic Account 1. Find EndNote on Snowden Library s homepage 2. Click the link to Sign up, then enter your email address,
More informationTransitHound Cellphone Detector User Manual Version 1.3
TransitHound Cellphone Detector User Manual Version 1.3 RF3 RF2 Table of Contents Introduction...3 PC Requirements...3 Unit Description...3 Electrical Interfaces...4 Interface Cable...5 USB to Serial Interface
More informationRack-Mount Receiver Analyzer 101
Rack-Mount Receiver Analyzer 101 A Decade s Worth of Innovation No part of this document may be circulated, quoted, or reproduced for distribution without prior written approval from Quasonix, Inc. Copyright
More informationMadiXtreme / Alpha-Link XLogic I/O system for PC and Mac Setup Guide V1.0 XLogic. This is SSL.
www.solidstatelogic.com MadiXtreme / Alpha-Link XLogic I/O system for PC and Mac Setup Guide V1.0 XLogic. This is SSL. Document History 82BSA101A March 2012 V1.0 Initial Release Contents Introduction 1
More informationKeysight Method of Implementation (MOI) for VESA DisplayPort (DP) Standard Version 1.3 Cable-Connector Compliance Tests Using E5071C ENA Option TDR
Revision 1.00 February 27, 2015 Keysight Method of Implementation (MOI) for VESA DisplayPort (DP) Standard Version 1.3 Cable-Connector Compliance Tests Using E5071C ENA Option TDR 1 Table of Contents 1.
More informationFord AMS Test Bench Operating Instructions
AMS Test Bench 09/2013 Ford AMS Test Bench Operating Instructions The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171 FAX: 800-826-3487
More informationUSER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1
by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information
More informationOperating Instructions
Operating Instructions HAEFELY TEST AG KIT Measurement Software Version 1.0 KIT / En Date Version Responsable Changes / Reasons February 2015 1.0 Initial version WARNING Introduction i Before operating
More informationREMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual
REMOTE I/O R30 SERIES PC CONFIGURATOR SOFTWARE Model: R30CFG Ver. 1.13 Users Manual 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Tel: +81-6-6659-8201 Fax: +81-6-6659-8510 http://www.m-system.co.jp/
More informationIT-100 INSTRUCTION MANUAL
IT-00 INSTRUCTION MANUAL I CONTENTS Ⅰ. INTRODUCTION... 日本語 Ⅱ. SETTING... 2. INITIAL SETTING... 2 -. Machine head settings...2-2. Adjusting the machine head angle (direct-drive motor type sewing machine
More informationEDL8 Race Dash Manual Engine Management Systems
Engine Management Systems EDL8 Race Dash Manual Engine Management Systems Page 1 EDL8 Race Dash Page 2 EMS Computers Pty Ltd Unit 9 / 171 Power St Glendenning NSW, 2761 Australia Phone.: +612 9675 1414
More informationHD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L HD4112 Manual Rev 1 Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1
More informationBefore attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
Operating Instructions Additional Business Intelligence Kit Model No. WJ-NVF20 WJ-NVF20E Before attempting to connect or operate this product, please read these instructions carefully and save this manual
More informationUsing different reference quantities in ArtemiS SUITE
06/17 in ArtemiS SUITE ArtemiS SUITE allows you to perform sound analyses versus a number of different reference quantities. Many analyses are calculated and displayed versus time, such as Level vs. Time,
More informationTeacher s AIDE Training System. EZ Teach Silver Installation
Teacher s AIDE Training System EZ Teach Silver Installation A front row seat for every Student in your class! Page 1 of 17 TRODUCTION...3 EZ TEACH SILVER STALLATION 5 EASY STEPS...3 EZ Teach Components...3
More informationJune/July 2016 Med Tips
Replacing the SeQual Integra Filter June/July 2016 Med Tips Helpful Hints and FAQs The SeQual Integra s Compressor Intake Filter (PN: SP4405-SEQ) will include a hook and loop fastener to better attach
More informationJAMAR TRAX RD Detector Package Power Requirements Installation Setting Up The Unit
JAMAR TRAX RD The TRAX RD is an automatic traffic recorder designed and built by JAMAR Technologies, Inc. Since the unit is a Raw Data unit, it records a time stamp of every sensor hit that occurs during
More informationApplication Note 11 - Totalization
Application Note 11 - Totalization Using the TrendView Recorders for Totalization The totalization function is normally associated with flow monitoring applications, where the input to the recorder would
More informationUser Calibration Software. CM-S20w. Instruction Manual. Make sure to read this before use.
User Calibration Software CM-S20w Instruction Manual Make sure to read this before use. Safety Precautions Before you using this software, we recommend that you thoroughly read this manual as well as the
More informationSystem Requirements SA0314 Spectrum analyzer:
System Requirements SA0314 Spectrum analyzer: System requirements Windows XP, 7, Vista or 8: 1 GHz or faster 32-bit or 64-bit processor 1 GB RAM 10 MB hard disk space \ 1. Getting Started Insert DVD into
More informationAmerican DJ. Show Designer. Software Revision 2.08
American DJ Show Designer Software Revision 2.08 American DJ 4295 Charter Street Los Angeles, CA 90058 USA E-mail: support@ameriandj.com Web: www.americandj.com OVERVIEW Show Designer is a new lighting
More information802DN Series A DeviceNet Limit Switch Parameter List
802DN Series A DeviceNet Limit Switch Parameter List EDS file Version 2.01 1. Operate Mode 1 (Sensor Output #1) Normally Open Normally Closed 2. Operate Mode 2 (Sensor Output #2) Normally Open Normally
More information0.56" 4 Digital Blue LED Panel Meter (rescalable) User s Guide
0.56" 4 Digital Blue LED Panel Meter (rescalable) User s Guide 2004-2009 Sure Electronics Inc. ME-SP037B_Ver1.0 0.56" 4 DIGITAL BLUE LED PANEL METER (RESCALABLE) USER S GUIDE Table of Contents Chapter
More informationVorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630)
Vorne Industries 87/719 Analog Input Module User's Manual 1445 Industrial Drive Itasca, IL 60143-1849 (630) 875-3600 Telefax (630) 875-3609 . 3 Chapter 1 Introduction... 1.1 Accessing Wiring Connections
More informationManual of Operation for WaveNode Model WN-2m. Revision 1.0
Manual of Operation for WaveNode Model WN-2m. Revision 1.0 TABLE OF CONTENTS 1. Description of Operation 2. Features 3. Installation and Checkout 4. Graphical Menus 5. Information for Software Expansion
More informationOwner's Manual. TOUCH SCREEN CONTROLLER for Air Conditioning Control System. Model BMS-CT5120UL. English
TOUCH SCREEN CONTROLLER for Air Conditioning Control System Model BMS-CT5120UL English Contents 1 Precautions for safety.................................................. 5 2 Main functions........................................................
More informationThe Switcher: TriCaster 855 Extreme
The Switcher: TriCaster 855 Extreme OVERVIEW The typical studio production is composed of content from various sources: CAMERAS: Moving images from studio cameras normally three. AUDIO from studio mics
More informationTyler SIS Student 360 Mobile
Tyler SIS Student 360 Mobile Overview Tyler SIS Student 360 Mobile is a mobile phone app version of the Tyler SIS Student 360 Parent Portal available on both ios and Android. It can be downloaded from
More informationTA Instruments Cement Analysis Software Getting Started Guide
TA Instruments Cement Analysis Software Getting Started Guide Overview Cement Analysis software from TA Instruments is a standalone software application for running cement setting experiments and analyzing
More informationFunction Manual SIMATIC HMI TP900. Operator Panel.
Function Manual SIMATIC HMI TP900 Operator Panel Edition 10/2016 www.siemens.com Introduction 1 Safety notes 2 Medium-voltage converters SIMATIC Description 3 Screens 4 Installing software 5 Function
More informationOPERATION MANUAL OF MULTIHEAD WEIGHER
OPERATION MANUAL OF MULTIHEAD WEIGHER Page 1 of 62 PREFACE Multihead weigher is automatic weighing equipment by using MCU control system to achieve high speed, accuracy and stable performance. Different
More informationpc-based controller user guide for vers software
eon-lt pc-based controller user guide for vers. 3.0.11 software TM Contents 7 7 9 11 11 15 15 15 16 17 18 21 21 21 22 23 23 23 24 25 25 25 26 26 26 26 Chapter 1: Eon-LT at a Glance Eon-LT Connectors Accessories
More informationUSER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0
by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information
More informationAEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE
AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE Thank you for purchasing a TSI AeroTrak Model 9110 Portable Airborne Particle Counter (particle counter). This guide will help you
More informationCOPYRIGHT NOVEMBER-1998
Application Notes: Interfacing AG-132 GPS with G-858 Magnetometer 25430-AM Rev.A Operation Manual COPYRIGHT NOVEMBER-1998 GEOMETRICS, INC. 2190 Fortune Drive, San Jose, Ca 95131 USA Phone: (408) 954-0522
More informationThis Service Bulletin may be distributed only to those groups indicated below with a check mark: End-use customers, owners and operators
Document Number: 601-00004-104 Title: MFD Configuration Save and Restore for Release 4.1.1 and 8.1.1 Revision: 01 Date: 09 March 2012 1. Planning Information 1.1 Distribution/Eligibility This Service Bulletin
More informationMultiQ Digital signage template system for widescreen monitors
Technical Note MultiQ Digital signage template system for widescreen monitors This document is intended as a guide for users of the MultiQ Digital Signage Template System for widescreen monitors in landscape
More informationPerforming a Measurement/ Reading the Data
CHAPTER 5 Performing a Measurement/ Reading the Data With the basic parameters set and the instrument calibrated (as discussed in Chapters 3 and 4), you are ready to take a measurement and examine the
More informationTemperature recorder with display and built-in printer Instruction manual
T-PRINT G0221E T-PRINT G0241 Temperature recorder with display and built-in printer Instruction manual CONTENT 1.0 BASIC RECORDER FEATURES...3 2.0 FIXED INSTALLATION OF RECORDER...3 3.0 RECORDER CONFIGURATION
More informationKF200 PORTABLE MANUAL
KF200 PORTABLE MANUAL THIS MANUAL CONTAINS: KF200 OPERATORS MANUAL KF200 GRAIN SOFTWARE MANUAL SPECIAL NOTE BOONE CABLE WORKS & ELECTRONICS, INC. 1773-219TH LANE - P.O. BOX 369 READ THIS ENTIRE BOOKLET
More informationPackage Contents. LED Protocols Supported. Safety Information. Physical Dimensions
Pixel Triton Table of Contents Package Contents... 1 Safety Information... 1 LED Protocols Supported... 1 Physical Dimensions... 1 Software Features... 2 LED Status... 2 Power... 2 Activity LED... 2 Link
More informationTHE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL
THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL INTRODUCTION The Gemini 5200 is another unit in a multi-purpose series of industrial control products that are field-programmable to solve multiple
More informationWeschler AMT Software for the Enhanced Version Transformer Advantage
Weschler AMT Software for the Enhanced Version Transformer Advantage The Weschler AMT software is used to configure and monitor a Transformer Advantage from a PC. The AMT software also simplifies extraction
More informationContents. Welcome to LCAST. System Requirements. Compatibility. Installation and Authorization. Loudness Metering. True-Peak Metering
LCAST User Manual Contents Welcome to LCAST System Requirements Compatibility Installation and Authorization Loudness Metering True-Peak Metering LCAST User Interface Your First Loudness Measurement Presets
More informationPicoScope 2000 Series PC Oscilloscopes
PicoScope 2000 Series PC Oscilloscopes User guide I PicoScope 2000 Series User Guide Table of Contents 1 Introduction...2...2 1 Overview...2 2 Safety symbols...3 3 Safety warning...3 4 FCC notice 5 CE
More informationThe DataView PowerPad III Control Panel
Setting Up a Recording Session in the DataView PowerPad III Control Panel By Mike Van Dunk The DataView PowerPad III Control Panel is designed for working with AEMC PowerPad III Power Quality Analyzers,
More informationViewCommander- NVR Version 3. User s Guide
ViewCommander- NVR Version 3 User s Guide The information in this manual is subject to change without notice. Internet Video & Imaging, Inc. assumes no responsibility or liability for any errors, inaccuracies,
More information11: PC MACs RealTime Pulldown
11: PC MACs RealTime Pulldown This Pulldown Menu is where all the commands having to do with the real time programming of a show can be found. Most of the commands are duplicates of the buttons and checkboxes
More informationKNX Dimmer RGBW - User Manual
KNX Dimmer RGBW - User Manual Item No.: LC-013-004 1. Product Description With the KNX Dimmer RGBW it is possible to control of RGBW, WW-CW LED or 4 independent channels with integrated KNX BCU. Simple
More informationChapter 1 : FCC Radiation Norm...3. Chapter 2 : Package Contents...4. Chapter 3 : System Requirements...5. Chapter 4 : Hardware Description...
Table of Contents Chapter 1 : FCC Radiation Norm...3 Chapter 2 : Package Contents...4 Chapter 3 : System Requirements...5 Chapter 4 : Hardware Description...6 Chapter 5 : Charging Your Video Watch...7
More informationSUGAR fx. Punchline User Manual
SUGAR fx Punchline User Manual Installation.... 3 Installing SUGARfx... 3 Contents What is Punchline?... 4 Using Punchline... 5 Punchline Transitions... 6 Parameters... 6 Punchline Titles.... 8 Parameters...
More informationDynamic Cable Rating Model Guidelines
lines Introduction This document describes how to set up, configure and run the Dynamic Cable Rating model in Ipsa. The Dynamic Cable Rating model (DCR) has been developed for the WPD FALCON project by
More informationAPPLICATION NOTE # Monitoring DTMF Digits Transmitted by a Phone
APPLICATION NOTE # Product: 930A Communications Test Set 930i Communications Test Set Monitoring DTMF Digits Transmitted by a Phone Introduction This Application Note describes how to configure and connect
More informationDVISm. DVISm - Mini Digital Video Insertion System. Quick Start Guide. Patent Pending
DVISm Patent Pending DVISm - Mini Digital Video Insertion System Quick Start Guide Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice, to make
More informationOPERATING MANUAL. including
OPERATING MANUAL including & If a portable or temporary three phase mains supply is used to power this desk, we recommend that the desk mains plug is removed before connecting or disconnecting the supply.
More informationEvent recording (or logging) with a Fluke 287/289 Digital Multimeter
Event recording (or logging) with a Fluke 287/289 Digital Multimeter Application Note One of the major features of the Fluke 280 Series digital multimeters (DMM) with TrendCapture is their ability to record
More informationapplication software
application software application software Input products / Shutter Output / RF output Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF
More informationTelevision Analyser - TVA97
Television Analyser - TVA97 Multi-functional instrument for RF applications setting the pace in professional RF technology summary setting the pace in professional RF technology Feature Frequency, Gain
More informationFR-8 and FR-16 Remote Control Operating Manual
FR-8 and FR-16 Remote Control Operating Manual Introduction The FR-8 and FR-16 are Ethernet-based remote control devices for Ashly Ethernet compatible products with DSP capabilities, including the Ashly
More informationTL-2900 AMMONIA & NITRATE ANALYZER DUAL CHANNEL
TL-2900 AMMONIA & NITRATE ANALYZER DUAL CHANNEL DATA ACQUISITION SYSTEM V.15.4 INSTRUCTION MANUAL Timberline Instruments, LLC 1880 S. Flatiron Ct., Unit I Boulder, Colorado 80301 Ph: (303) 440-8779 Fx:
More informationSERCOS TSX CSY 84 Module V
SERCOS TSX CSY 84 Module V At a Glance Aim of this Part What's in this part? This part presents the SERCOS TSX CSY 84 module, its operating features and its installation. This Part contains the following
More informationTechnology Control Technology
L e a v i n g C e r t i f i c a t e Technology Control Technology P I C A X E 1 8 X Prog. 1.SOUND Output Prog. 3 OUTPUT & WAIT Prog. 6 LOOP Prog. 7...Seven Segment Display Prog. 8...Single Traffic Light
More informationCOLOR TFT LCD MONITOR. Manual
COLOR TFT LCD MONITOR Manual Safety defended: Properly maintains your system to be possible to guarantee its service life and to reduce the damage risk. It should avoid the damp and exceeding temperature
More informationOptiflex Interactive Video System
Optiflex Interactive Video System Optiflex Interactive Video System 1 Before You Start...............2 On-site Video Surveillance.......6 Touchscreen Interface Viewing...10 Secure Remote Look-in........16
More informationapplication software
application software application software Input products / Shutter Output / RF output Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF
More informationir32 installation files for IR receive and blaster functionality. mce the HD PVR MCE Support installer (setup.exe)
HD PVR \ Colossus Media Center Support Release Notes Version 1.1.29178 6/27/2011 Support for Windows Media Center allows you to use one HD PVR or Colossus to watch, pause and record high definition TV
More informationEdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY
EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY 493456301 Rev B April 2009 Table of Contents Installation... 1 Setup... 2 Operation... 4 Live Video... 4 Video Settings... 5 Network
More informationMXS Strada USER GUIDE
MXS Strada USER GUIDE AiM TECH Srl. Via Cavalcanti, 8 20063 Cernusco S/N (MI) Italia Tel. (+39) 02.9290571 Made in Italy www.aim-sportline.com MXS Strada 01. INTRODUCTION 02. WHAT IS IN THE KIT 03. LAYOUT
More informationTF5 / TF3 / TF1 DIGITAL MIXING CONSOLE. TF Editor User Guide
TF5 / TF3 / TF1 DIGITAL MIXING CONSOLE EN Special notices Copyrights of the software and this document are the exclusive property of Yamaha Corporation. Copying or modifying the software or reproduction
More informationJ6 User Manual. User Manual. Multi-Screen Splicing Processor J6. Xi an NovaStar Tech Co., Ltd. Rev1.0.1 NS
J6 User Manual User Manual Multi-Screen Splicing Processor J6 Rev1.0.1 NS160110162 Statement Dear users, You are welcome to use the J6, a multi-screen splicing processor of Xi'an NovaStar Tech Co., Ltd.
More informationLCD MONITOR. quick start guide P2070,P2270,P2370,P2070G,P2270G,P2370G
LCD MONITOR quick start guide P2070,P2270,P2370,P2070G,P2270G,P2370G ii Introduction Package Contents Please make sure the following items are included with your monitor. If any items are missing, contact
More informationSpectacle Motion Board Hookup Guide
Page 1 of 16 Spectacle Motion Board Hookup Guide Spectacle Motion Board The Spectacle Motion Board makes it easy to add movement to your Spectacle projects. It can control up to 5 servo motors, either
More informationIRIG-B PTP Clock Converter Output Module Hardware Installation Manual
IRIG-B PTP Clock Converter Output Module Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: May 2012 Version: V1.2 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678
More informationIntroduction to EndNote. Presented October 3, B.C. Women and Children s Hospital
Introduction to EndNote Presented October 3, 2018 @ B.C. Women and Children s Hospital Facilitator Marianne Hoffard, Student Librarian Woodward Library, UBC Agenda Getting started Capturing information
More informationInfiniTV 4 Installation Instructions
InfiniTV 4 Installation Instructions 1. Obtain a CableCARD from your cable TV service provider 1. Call your cable TV service provider and tell them you need a multi-stream CableCARD (M-Card) for a Ceton
More informationU S E R G U I D E HD1000
U S E R G U I D E HD1000 1 W e l c o m e t o R o k u! In This Guide... Bring your HDTV to life with Roku. For the first time, you ll enjoy viewing your favorite digital photos in high-definition on your
More informationAnalyzing and Saving a Signal
Analyzing and Saving a Signal Approximate Time You can complete this exercise in approximately 45 minutes. Background LabVIEW includes a set of Express VIs that help you analyze signals. This chapter teaches
More informationUser Guide & Reference Manual
TSA3300 TELEPHONE SIGNAL ANALYZER User Guide & Reference Manual Release 2.1 June 2000 Copyright 2000 by Advent Instruments Inc. TSA3300 TELEPHONE SIGNAL ANALYZER ii Overview SECTION 1 INSTALLATION & SETUP
More informationThe amazing power of FiOS starts here.
SELF-INSTALLATION GUIDE The amazing power of FiOS starts here. LET S GET STARTED Welcome to a network that s light years ahead. Welcome to life on FiOS. Congratulations on choosing Verizon FiOS! You re
More informationWJ-HD616K/716K Quick Reference Guide
WJ-HD616K/716K Quick Reference Guide Remote Operation Using Internet Explorer For a local operation quick guide refer to Local Quick Guide available for download http://panasonic.ca/english/customercare/operatinginstructions/query.asp
More informationNetwork Disk Recorder WJ-ND200
Network Disk Recorder WJ-ND200 Network Disk Recorder Operating Instructions Model No. WJ-ND200 ERROR MIRROR TIMER HDD1 REC LINK /ACT OPERATE HDD2 ALARM SUSPEND ALARM BUZZER STOP Before attempting to connect
More informationVISSIM TUTORIALS This document includes tutorials that provide help in using VISSIM to accomplish the six tasks listed in the table below.
VISSIM TUTORIALS This document includes tutorials that provide help in using VISSIM to accomplish the six tasks listed in the table below. Number Title Page Number 1 Adding actuated signal control to an
More informationUltra 4K Tool Box. Version Release Note
Ultra 4K Tool Box Version 2.1.43.0 Release Note This document summarises the enhancements introduced in Version 2.1 of the software for the Omnitek Ultra 4K Tool Box and related products. It also details
More informationSignalTap Plus System Analyzer
SignalTap Plus System Analyzer June 2000, ver. 1 Data Sheet Features Simultaneous internal programmable logic device (PLD) and external (board-level) logic analysis 32-channel external logic analyzer 166
More informationCyAn User Manual. Flow & Mass Cytometry Center Biomedical Core facility. Technion Faculty of Medicine
CyAn User Manual Flow & Mass Cytometry Center Biomedical Core facility For assistant please call: Technion Faculty of Medicine Amir Grau 054-210-0778 Yaakov Sakoury 050-749-8586 Ofer Shenker 052-456-8846
More informationVeriLUM 5.2. Video Display Calibration And Conformance Tracking. IMAGE Smiths, Inc. P.O. Box 30928, Bethesda, MD USA
VeriLUM 5.2 Video Display Calibration And Conformance Tracking IMAGE Smiths, Inc. P.O. Box 30928, Bethesda, MD 20824 USA Voice: 240-395-1600 Fax: 240-395-1601 Web: www.image-smiths.com Technical Support
More information