SPECIAL SPECIFICATION 6686 BSIF CCTV Central Equipment
|
|
- Charlene Parsons
- 5 years ago
- Views:
Transcription
1 2004 Specifications CSJ , & SPECIAL SPECIFICATION 6686 BSIF CCTV Central Equipment 1. Description. Furnish and install closed circuit television (CCTV) central equipment in the Border Safety Inspection Facility (BSIF) location(s) as shown on the plans, and as detailed in this Special Specification. 2. Materials. (1) General Requirements. All materials furnished, assembled, fabricated, or installed under this Item will be new, corrosion resistant, and in strict accordance with the details shown on the plans and in this Special Specification. (2) Functional Requirements. Furnish and install, at the locations shown on the plans, CCTV central equipment to control the video cameras in the field and the video signals in the control center. Provide CCTV central equipment including, but not be limited to, the following: 1. Video Monitors (color). 2. Distribution Amplifiers. 3. Video Patch Panels. 4. Waveform Monitor. 5. Video Color Quad Unit. 6. Power Supplies, Connectors, Harness and Accessories. Submit a layout of individual rack mount components for approval. (a) Video Monitor. Provide 19 in. minimum, measured diagonally, color video monitors at each location as indicated on the plans. Provide monitors with the following requirements: - Video Signal: EIA 525 lines, 60 fields. - Color System: NTSC. - Video Input: Composite 1 V P-P. - Operating Temperature: 32ºF to 104ºF. (b) Distribution Amplifiers. Provide rack mountable, modular, distribution amplifiers (DA) with gain and equalization control. Provide each DA with a minimum of 4 outputs. Ensure loading of either output does not affect the signal on the other output. Ensure DA has a nominal input and output impedance of 75 ohms, and will not introduce any measurable distortion to the signal
2 Ensure all DA inputs and outputs, including a minimum of one monitoring output, are routed through the patch panel. Ensure the DA s video input and output connectors are female BNC. Ensure the DA can drive the video output signal up to 1500 ft. with RG59 cables. (c) Video Patch Panels. Install, in the computer room, patch bays to access video signals for monitoring and bypassing purposes. Ensure all jacks, patch cord plugs, accessories, and adapters are gold plated and produced by the same manufacturer. Ensure they conform to the Western Electric 75 ohm (0.09 in. center pin) standard. Ensure jacks are mounted in double rows on 3.5 in. panels with 0.63 in. vertical spacing and 0.83 inch horizontal spacing. If metal panels are used, ensure provisions are made to insulate the cable shield from the panel. In general, provide signal sources on the top row, and corresponding signal destinations, if any, are below them on the bottom row. Ensure accessories are supplied for use with jacks in the patch bay: - 24 in. patch cords; - 48 in. patch cords; - 10 ft. coax cables with male BNC each end; - Patch plugs to female BNC adapter; - 75 ohm patch plug terminators; - Looping plugs with pinch type handle, in addition to the number required for normal operation; and - Unused patch bay jacks, installed in unlabeled positions. Furnish and install a patch bay to access video signals for monitoring and bypass purposes. Provide a patch bay between each of the following component pairs; the video fiber optic receivers and the DA, the DA and the analog video switch, and the analog video switch and monitors. An additional patch bay is required for terminated test points from the DA. (d) Waveform Monitor. Provide a calibrated waveform monitor permanently mounted in the equipment rack, near the patch bay, and in easy viewing distance of all video signal level adjustments. Ensure the waveform monitor obtains its "A" input signal from an output of the routing switcher/titler. Ensure the signal is looped through the patch bay and looped through the waveform monitor, where it is terminated with a 1% tolerance, 75 ohm, terminator. Ensure the "B" input is available at a jack on the patch panel. Ensure the waveform monitor has the following characteristics: 1. A minimum of a 5 in. diagonal viewing area. 2. Frequency response from 25 hertz to 10 mhz flat ± 1% 3. Full scale vertical deflection of 140 ire units ± 1% 4. Internal one volt, ± 1%, calibration signal. 5. Provide view of signals at either the horizontal or vertical rate and a means provided for expanding any part of the signal display either vertically or horizontally. 6. Provide 2 signal inputs. Ensure the viewed signal and the scope synchronization are each be capable of being derived from either input
3 7. Ensure input response are selectable between: Flat, ire, chroma only and differential gain. 8. Ensure a switchable DC restorer is proved to maintain display stability with varying APL. 9. Ensure mounting hardware is supplied to fit a 19 in. rack, with any space not used filled in with blank out panels. (e) Video Color Quad Unit. Provide the video color quad unit that allows up to 4 video camera signals to be displayed simultaneously on a single monitor screen divided into 4 blocks. Ensure each of 4 images in the quad display mode are refreshed and appear in real time with no motion loss due to multiplexed display images. Ensure the quad unit is able to use virtually any 2:1 interlace type camera. Ensure the quad unit allows sequential display of quad page and each camera at full screen on live display monitor port. Ensure the unit supports remote control of functions through an RS-232 serial port. Ensure the Color Quad Video Generator meets the following minimum requirements: - Operating power may be 120 V AC or 12 V DC with adapter - Operating temperature range from F - Video input four 1.0 V p-p composite video - Monitor output 1.0 V p-p composite video - On screen time, date, and camera title display option - VCR output 1.0 V p-p composite video (f) Wiring and Connectors. Ensure coaxial cable is used for making video connections between devices in the computer room. Ensure the cables are the RG- 59 type with a nominal impedance of 75 ohms. Ensure all cables have a polyethylene dielectric with copper braid shield having a minimum of 95% shield coverage and not greater than 3.4 db attenuation per 100 ft. at 100 MHz. Video connectors shall be BNC die crimp type. Ensure coax braid is neatly trimmed before crimping the connector to insure no possibility of contact between braid and inner connector. Ensure there are no nicks in the center conductor. Ensure crimps are mechanically secure and made in such a way that no braid is left exposed or protrudes from the connector. Ensure the center pin is gold plated and installed with the tip of the center pin flush with the front edge of the connector. Ensure cables are neatly dressed and bundled with nylon cable ties. Ensure each cable is marked with a unique identification number at a point 6 in. from each end of the cable. Ensure numbering is done by applying adhesive plastic tape with machine printed black figures on white background. Thermal, or inked ribbon, computer printed labels are not satisfactory. Ensure identification is read upright when holding the cable horizontally with the connector to the left. Ensure the finished identification number is protected with a piece of clear shrinkable tubing shrunk tightly over the label and extending at least 1/4 in. either side of the label. Ensure each cabinet or rack contains a typed list showing the cabinet identification and the numbers, description, source and destinations of all cable in that cabinet. Ensure the cable list is heat laminated to protect it from moisture and dirt. Ensue the system schematic is clearly identify all cables by number
4 (g) Interconnect Harness and Accessories. Provide all interconnect harnesses and accessories needed for a completely integrated system. Ensure these cables/harnesses are properly labeled on either end of the cable assemble. Provide cables which consist of but not be limited to: - RS232 cables - Video coaxial cables - Twisted pair - CAT 5 cables (3) Electrical Requirements. (a) Video Monitor. Provide color video monitors with solid state design, with the exception of the picture tube. Ensure color video monitor meets the following requirements: 1. Video Input - EIA-170 standard, black negative polarity, composite signal, BNC connector, termination selectable between high impedance loop through or 75 ohms. 2. Resolution lines vertical, 450 lines horizontal, measured per EIA-170 standard. 3. Geometric Distortion - 2% maximum. 4. Gray Scale - Capable of displaying 10 discernible shades of gray. 5. Scanning - 2:1 interlaced, 525 lines/frame, frames per second per EIA- 70 standard, scanning rate 60 hz vertical, and 15,734 hz horizontal. 6. Control Functions - Front panel controls: Power on/off, contrast, brightness, horizontal hold (if used), vertical hold (if used), color (chroma), and hue (tint or phase). 7. Refresh Rate image refresh rate of 60 fields/second or greater 8. Ensure integral means are provided for degaussing, either automatically at power-up, or manually by means of an external pushbutton. 9. Ensure the monitor is not be capable of television broadcast reception. (b) Power Requirements. Ensure the CCTV central equipment meets all of its specified requirements when the input power is 115 ± 20 volts AC, 60 ± 3 Hz. Ensure the maximum power required does not exceed 600 watts. Ensure the equipment operation is not be affected by transient voltages, surges, and sags normally experienced on commercial power lines. It is the Contractor's responsibility to check the local power service to determine if any special design is needed for the equipment. Ensure the extra cost, if required, is included in the price bid of this Item. (c) Wiring. Ensure all wiring meets the requirements of the National Electric Code. Ensure all wires are cut to proper length before assembly. Ensure no wire is doubled back to take up slack. Ensure wires are neatly laced into clamps. Ensure cable slack is provided to facilitate removal and replacement of assemblies, panels and modules
5 (d) Transient Suppression. Ensure all DC relays, solenoids, and holding coils have diodes across the coils for transient suppression. (e) Power Service Protection. Ensure the equipment contains readily accessible, manually resettable or replaceable circuit protection devices (such as circuit breakers or fuses) for equipment and power source protection. (f) Fail Safe Provision. Ensure the equipment is designed such that the failures of the equipment will not cause the failure of any other unit or equipment. (4) Mechanical Requirements. (a) Enclosure. Ensure the video monitor, distribution amplifier, video patch panel, and waveform monitor are rack mounted and located as shown on the plans. (b) Modular Design. Ensure the equipment is modular in design such that major portions may be readily replaced in the field. Ensure modules of unlike functions are mechanically keyed to prevent insertion into the wrong socket or connector. Ensure all modules and assemblies are clearly identified with name, model number, serial number, and any other pertinent information required to facilitate equipment maintenance. (c) Connector and Harness. Ensure all external connections are made by means of connectors. Ensure the connectors are keyed to preclude improper hookups. Ensure all wires to and from the connectors are color coded and appropriately marked. Ensure pins and mating connectors are corrosion resistant. (5) Environmental Design Requirements. Ensure the equipment meets all its specified requirements during and after subjecting to any combination of the following conditions: 1. Ambient temperature range of 40ºF to 122ºF. 2. Relative humidity up to 90% non-condensing. 3. Construction. (1) General. Ensure the equipment design and construction utilizes the latest available techniques with a minimum number of parts, subassemblies, circuits, cards, and modules to maximize standardization and commonality. Ensure the equipment is designed for ease of maintenance. Ensure all component parts are readily accessible for inspection and maintenance. Ensure test points are provided for checking essential voltages and waveforms. (2) Electronic Components. Ensure all electronic components comply with Special Specification, "Electronic Components. (3) Mechanical Components. Ensure all external screws, nuts, and locking washers are stainless steel. Ensure no self-tapping screws are used unless specifically approved
6 Ensure all parts are made of corrosion resistant material, such as plastic, stainless steel, anodized aluminum or brass. Ensure all materials used in construction are protected from fungus growth and moisture deterioration. Ensure dissimilar metals are separated by an inert dielectric material. (4) Testing. Perform testing in accordance with Article 2, Special Specification, Border Safety Inspection Facility Testing, Training, Documentation, Final Acceptance, and Warranty. (5) Training. Perform training in accordance with Article 3, Special Specification, Border Safety Inspection Facility Testing, Training, Documentation, Final Acceptance, and Warranty. (6) Documentation. Provide documentation in accordance with Articles 4 and 5, Special Specification, Border Safety Inspection Facility Testing, Training, Documentation, Final Acceptance, and Warranty. (7) Warranty. Provide a warranty in accordance with Article 7, Special Specification, Border Safety Inspection Facility Testing, Training, Documentation, Final Acceptance, and Warranty. 4. Measurement. This Item will be measured as each unit furnished, installed, made fully operational and tested in accordance with these Special Specifications or as directed by the Engineer. 5. Payment. The work performed and materials furnished in accordance with this Item and measured as provided under "Measurement" will be paid for at the unit price bid for " Video Monitors, Distribution Amplifiers, Video Patch Panels, Waveform Monitor and Video Color Quad Unit. This price is full compensation for furnishing all equipment described under this Item with all cables and connectors, all documentation and testing; and shall include the cost of furnishing all labor, materials, training, warranty, equipment, and incidentals
SPECIAL SPECIFICATION 2344 TMC Support Equipment
2004 Specifications CSJ 0912-00-488 SPECIAL SPECIFICATION 2344 TMC Support Equipment 1. Description. Furnish Traffic Management Center (TMC) support equipment in the City of Missouri City TMC location
More informationSPECIAL SPECIFICATION 8494 CCTV Central Equipment
2004 Specifications CSJ 0912-34-150 SPECIAL SPECIFICATION 8494 CCTV Central Equipment 1. Description. Furnish and install closed circuit television (CCTV) central equipment in the City of Missouri City
More information1993 Specifications CSJ , etc. SPECIAL SPECIFICATION ITEM CCTV Central Equipment
1993 Specifications CSJ 0922-33-042, etc. SPECIAL SPECIFICATION ITEM 8549 CCTV Central Equipment 1. Description. This Item shall govern for the furnishing and installation of closed circuit television
More informationSPECIAL SPECIFICATION 1676 Traffic Management Center Electronics
1993 Specifications CSJ s 0912-34-101 & 0027-08-108, etc. SPECIAL SPECIFICATION 1676 Traffic Management Center Electronics 1. Description. Furnish and install electronics equipment in the Traffic Management
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM 6031 SINGLE MODE FIBER OPTIC VIDEO TRANSMISSION EQUIPMENT
1995 Metric CSJ 0508-01-258 SPECIAL SPECIFICATION ITEM 6031 SINGLE MODE FIBER OPTIC VIDEO TRANSMISSION EQUIPMENT 1.0 Description This Item shall govern for the furnishing and installation of color Single
More informationSPECIAL SPECIFICATION 1987 Single Mode Fiber Optic Video Transmission Equipment
1993 Specifications CSJ 0027-12-086, etc. SPECIAL SPECIFICATION 1987 Single Mode Fiber Optic Video Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation of color
More informationSPECIAL SPECIFICATION 6911 Fiber Optic Video Data Transmission Equipment
2004 Specifications CSJ 3256-02-079 & 3256-03-082 SPECIAL SPECIFICATION 6911 Fiber Optic Video Data Transmission Equipment 1. Description. Furnish and install Fiber Optic Video Data Transmission Equipment
More informationSPECIAL SPECIFICATION 1291 Fiber Optic Video Data Transmission Equipment
1993 Specifications CSJ 0500-01-117 SPECIAL SPECIFICATION 1291 Fiber Optic Video Data Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic Video
More information1995 METRIC CSJ SPECIAL SPECIFICATION ITEM 6573 CCTV CENTRAL EQUIPMENT
1995 METRIC CSJ 0196-03-209 SPECIAL SPECIFICATION ITEM 6573 CCTV CENTRAL EQUIPMENT 1.0 DESCRIPTION. THIS ITEM SHALL GOVERN FOR THE FURNISHING AND INSTALLATION OF CLOSED CIRCUIT TELEVISION (CCTV) CENTRAL
More informationSPECIAL SPECIFICATION 6735 Video Optical Transceiver
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6735 Video Optical Transceiver 1. Description. This Item governs the furnishing and installation of Video optical transceiver (VOTR) in field location(s)
More informationSPECIAL SPECIFICATION 6734 CCTV Central Equipment
1995 Metric CSJ 0038-01-033, Etc. SPECIAL SPECIFICATION 6734 CCTV Central Equipment 1. Description. This Item shall govern for the furnishing and installation of Closed Circuit Television (CCTV) central
More informationSPECIAL SPECIFICATION 6700 CCTV Field Equipment
2004 Specifications CSJ 0017-10-240 SPECIAL SPECIFICATION 6700 CCTV Field Equipment 1. Description. Provide, install, and make fully operational with the TransGuide system Closed Circuit Television (CCTV)
More informationSPECIAL SPECIFICATION 1726 CCTV Field Equipment
1993 Specifications CSJ 0018-06-021& 0922-11-017 SPECIAL SPECIFICATION 1726 CCTV Field Equipment 1. Description. This Item shall govern for the furnishing and installation of closed circuit television
More informationSPECIAL SPECIFICATION 6713 Ethernet Video Decoder (MPEG-4)
2004 Specifications CSJ 0016-04-103, etc. SPECIAL SPECIFICATION 6713 Ethernet Video Decoder (MPEG-4) 1. Description. Furnish, install, and make fully operational with the TransGuide or Combined Transportation,
More informationSPECIAL SPECIFICATION 6612 T1 Discrete Cosine Transform (DCT) Color Video Compression System
1993 Specifications Fort Worth District SPECIAL SPECIFICATION 6612 T1 Discrete Cosine Transform (DCT) Color Video Compression System 1. DESCRIPTION. THIS ITEM SHALL REGULATE THE FURNISHING AND INSTALLATION
More informationSPECIAL SPECIFICATION 1116 CCTV Field Equipment
1993 Specifications CSJ 0521-04-190 SPECIAL SPECIFICATION 1116 CCTV Field Equipment 1. Description. This Item shall govern for the furnishing and installation of Closed Circuit Television (CCTV) Field
More informationSPECIAL SPECIFICATION 6559 Telecommunication Cable
2004 Specifications CSJ 0015-09-147, etc. SPECIAL SPECIFICATION 6559 Telecommunication Cable 1. Description. This specification governs the materials, installation, termination, splicing, testing, training,
More informationSPECIAL SPECIFICATION 8540 Telecommunication Cable
2004 Specifications CSJ 0914-00-307 & CSJ 0914-25-003 SPECIAL SPECIFICATION 8540 Telecommunication Cable 1. Description. This specification governs the materials, installation, termination, splicing, testing,
More informationSPECIAL SPECIFICATION :1 Video (De) Mux with Data Channel
1993 Specifications CSJ 0924-06-223 SPECIAL SPECIFICATION 1160 8:1 Video (De) Mux with Data Channel 1. Description. This Item shall govern for furnishing and installing an 8 channel digital multiplexed
More informationSECTION 683 VIDEO OPTICAL TRANSCEIVER WITH BI-DIRECTIONAL DATA CHANNEL DESCRIPTION
683 SECTION 683 VIDEO OPTICAL TRANSCEIVER WITH BI-DIRECTIONAL DATA CHANNEL DESCRIPTION 683.01.01 GENERAL A. The Contractor shall furnish the designated quantity of Video Optical Transceiver (VOTR) pairs
More informationSPECIAL SPECIFICATION 1118 Dual OC-3 ATM MPEG-2 Encoder
1993 Specifications CSJ 0521-04-190 SPECIAL SPECIFICATION 1118 Dual OC-3 ATM MPEG-2 Encoder 1. Description. Furnish, install, and make fully operational an Asynchronous Transfer Mode (ATM) Video Encoder
More informationSECTION 7 -- CROSS-CONNECT SYSTEMS
DETAIL ENGINEERING REQUIREMENTS AT&T March, 2016 Section 7, ATT-TP-76400 Revised NA SECTION 7 -- CROSS-CONNECT SYSTEMS CONTENTS PAGE 1. GENERAL... 7-2 1.1. Introduction... 7-2 1.2. Cable Holes... 7-2 1.3.
More informationOPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION
OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION The Psidex Audio Laboratory PGP- 1A is a vacuum tube based microphone preamp and program line amplifier designed to provide solid, robust
More informationAutomatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
More informationCONTRACTORS SPECIFICATION
VICON PRODUCT SPECIFICATION NOTES SPEC NO. REV. SEC. SUPERSEDES PRODUCT SPECIFICATION 735-594 735 1299 10 MODEL: V1902VCT PRODUCT CODES: REFER TO TABLE 1 DESCRIPTION: VICOAX TRANSMITTER FOR A COAXIAL CONTROL
More informationDISTRIBUTION AMPLIFIER
MANUAL PART NUMBER: 400-0045-005 DA1907SX 1-IN, 2-OUT VGA/SVGA/XGA/UXGA DISTRIBUTION AMPLIFIER USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL...2 GUIDELINES FOR RACK-MOUNTING...2
More informationNon Magnetic Connectors
Non Magnetic Connectors Johnson Components builds coaxial connectors using innovative materials and design to provide Mil Spec Performance at a commercial price. Now we offer our Non Magnetic Connectors
More informationSPECIAL SPECIFICATION 6740 Video Imaging Vehicle Detection System
1995 Metric CSJ s 0918-45-344 & 0008-08-059 SPECIAL SPECIFICATION 6740 Video Imaging Vehicle Detection System 1. Description. Install a Video Imaging Vehicle Detection System (VIVDS) that monitors vehicles
More informationSpecial Specification 6293 Adaptive Traffic Signal Control System
Special Specification Adaptive Traffic Signal Control System 1. DESCRIPTION 2. MATERIALS Furnish, install, relocate, or remove adaptive traffic signal control (ATSC) system software and equipment at locations
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationSPECIAL SPECIFICATION 2284 Fiber Optic Cable (Self-Supporting)
2004 Specifications CSJ 0086-14-046 SPECIAL SPECIFICATION 2284 Fiber Optic Cable (Self-Supporting) 1. Description. Furnish, install, splice, field terminate, and test the fiber optic cables. 2. Materials.
More informationSPECIAL SPECIFICATION 6191 Fiber Optic Cable
2004 Specifications CSJ 0014-02-014, etc SPECIAL SPECIFICATION 6191 Fiber Optic Cable 1. Description. Furnish, install, splice, field terminate, and test the fiber optic cables. 2. Materials. A. General
More informationCoastal Carolina University RE-BID WILLIAMS BRICE RENOVATION AND REPAIR October 19, 2018 Construction Documents
PART 1 - GENERAL 1.1 SUMMARY SECTION 271500 COMMUNICATIONS HORIZONTAL CABLING A. Section Includes: 1. UTP cabling. 2. Telecommunications outlet/connectors. 3. Cabling system identification products. 1.2
More informationSECTION COMMUNICATIONS HORIZONTAL CABLING
SECTION 271500 COMMUNICATIONS HORIZONTAL CABLING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. UTP cabling. 2. Telecommunications outlet/connectors including patch panels. 3. Cabling identification
More informationMulti-Media Installation Guide
Multi-Media Installation Guide Coaxial Page 2 Data Plug Page 7 Data Jack Page 10 Telephone Page 13 Splicing Page 15 Cable Types Cable Types Two basic types of cable are used in multimedia installations.
More informationMonochrome Video Monitors
Instructions for Use Monochrome Video Monitors En F D E NL I LTC 2009 LTC 2012 LTC 2017 Philips Communication & Security Systems GB F D E NL I Instructions for Use...1.1 Mode d emploi...2.1 Bedienungsanleitung...3.1
More informationSpecial Specification 6002 Video Imaging Vehicle Detection System
6002 Special Specification 6002 Video Imaging Vehicle Detection System 1. DESCRIPTION 2. DEFINITIONS Install a Video Imaging Vehicle Detection System (VIVDS) that monitors vehicles on a roadway via processing
More information1x12 VGA & Audio over CAT5 Splitter
SP-9112 1x12 VGA & Audio over CAT5 Splitter User Manual rev: 160322 Made in Taiwan Safety and Notice The SP-9112 1x12 VGA & Audio over CAT5 Splitter has been tested for conformance to safety regulations
More informationElectro Magnetic Compatibility (EMC) Warning. Important notes for users in the U.K. FCC declaration. Caution. Fuse
Warning: to prevent fire or shock hazard, do not expose camera or monitor to rain or moisture. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the presence
More informationTR6102HD HDTV/DVD/COMPONENT VIDEO TO RGBHV TRANSCODER USER S GUIDE
MANUAL PART NUMBER: 400-0031-003 PRODUCT REVISION: 1 HDTV/DVD/COMPONENT VIDEO TO RGBHV TRANSCODER USER S GUIDE INTRODUCTION Thank you for your purchase of the Transcoder. We are certain that you will find
More informationModel Extend HDMI audio and video connections up to 300 feet. Add up to 8 additional receivers with a dedicated network switch
HDMI Extender over Single CAT 6 Cable with IR Control Model 103002 Extend HDMI audio and video connections up to 300 feet Utilize existing Cat 6 wiring for an easy installation Add up to 8 additional receivers
More informationDEPARTMENT OF THE ARMY TECHNICAL BULLETIN CALIBRATION PROCEDURE FOR AUTOMATIC VIDEO CORRECTOR TEKTRONIX, MODEL 1440 (NSN )
DEPARTMENT OF THE ARMY TECHNICAL BULLETIN TB 11-5820-861-35 CALIBRATION PROCEDURE FOR AUTOMATIC VIDEO CORRECTOR TEKTRONIX, MODEL 1440 (NSN 5820-00-570-1978) Headquarters, Department of the Army, Washington,
More informationModel 5240 Digital to Analog Key Converter Data Pack
Model 5240 Digital to Analog Key Converter Data Pack E NSEMBLE D E S I G N S Revision 2.1 SW v2.0 This data pack provides detailed installation, configuration and operation information for the 5240 Digital
More informationModel /29S RF Splitter
Instruction Manual Model 1584-29/29S RF Splitter March 2013, Rev. 0 LNB VOLTAGE A B MODEL 1584 COMBINER CROSS TECHNOLOGIES INC. GND+DC ON Data, drawings, and other material contained herein are proprietary
More informationUTP ACTIVE TRANSCEIVER HUB
VI6116 UTP ACTIVE TRANSCEIVER HUB USER S MANUAL 7810 Trade Street, Suite 100 San Diego, CA 92121, U.S.A. Phone: (858) 484-5209 Fax: (858) 484-1205 1 1. Introduction The Vigitron VI6116 is a 16 port active
More informationUNIVERSITY of NORTH DAKOTA LOW VOLTAGE COMMUNICATIONS STANDARDS FOR CABLING, PATHWAYS, AND SPACE
UNIVERSITY of NORTH DAKOTA LOW VOLTAGE COMMUNICATIONS STANDARDS FOR CABLING, PATHWAYS, AND SPACE Prepared in cooperation and approval from BICSI Building Industry Consulting Services International and
More informationMASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz
Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO
More informationModel Colorado Ultra Wide Bandwidth HDTV Matrix Switch
HDTV Supply, Inc www.hdtvsupply.com Model Colorado Ultra Wide Bandwidth HDTV Matrix Switch Overview: This product is a full featured video & audio matrix switch. It is most commonly used to independently
More informationUNSIGNED HARDCOPY NOT CONTROLLED
SUBJECT: APPROVED BY STATUS PURPOSE AFFECTED FUNCTIONS REFERENCES Cable and Harness Making Manager, Hardware Engineering Maintenance Revision Establishes requirements for the fabrication and inspection
More information1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Fiber Optic Cable System
1993 Specifications CSJ 0008-12-071 SPECIAL SPECIFICATION ITEM 6540 Fiber Optic Cable System 1.0 Description. This item shall govern for the furnishing and installation of fiber optic cables in designated
More informationImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL
SPECIFICATIONS MODEL NUMBER: XRT910-0-0-GB-XX XRT911-0-0-GB-XX XTT911-0-0-NN-XX IMPROX TRT ImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL Working Environment XRT910-0-0-GB-XX... (Aluminium Extruded
More informationNational Wire and Cable and National Cable Molding Headquarters Los Angeles California
National Wire and Cable and National Cable Molding Headquarters Los Angeles California CAPABILITIES Medical Business Machines Communications Equipment Computer Equipment Audio Systems General Instrumentation
More informationK Service Source. Apple High-Res Monochrome Monitor
K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal
More informationINTRODUCTION INSTALLATION LIGHTNING RETARDING LOOPS. Figure 1. Relay Box Antenna Connections. Relay Box Cable Connections
INTRODUCTION The Ameritron RCS-8V is a remote controlled coaxial RF switch that will operate with negligible loss, radiation and VSWR at all frequencies up to 250 MHz. Only a slight compromise in VSWR
More informationINSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM
INSTALLATION AND OPERATION INSTRUCTIONS EVOLUTION VIDEO DISTRIBUTION SYSTEM ATTENTION: READ THE ENTIRE INSTRUCTION SHEET BEFORE STARTING THE INSTALLATION PROCESS. WARNING! Do not begin to install your
More information(1) (2) (3) Bedienungs- und Montageanleitung. Safety instructions. Structure of the device
3 x cinch/s-video socket Order no. 33 1532 xx USB/3.5 mm audio socket Order no. 33 1539 xx VGA socket Order no. 33 1540 xx VGA socket with screw-in lift terminals Order no. 33 1541 xx High definition socket
More informationVPS1 Installation Manual
1-512-756-1678 VPS1 Installation Manual VPS1 Sender (Remote Unit) VPS1 Viewer (Local Unit) Contents Introduction...2 Features...2 Packing Checklist...2 The Connection Layout of VPS1...2 Certificate...2
More informationAUTOMATIC VIDEO LOSS A/B SWITCH
CG-X AUTOMATIC VIDEO LOSS A/B SWITCH INSTRUCTION BOOK IB647502 TABLE OF CONTENTS DESCRIPTION 2 MOUNTING INSTRUCTIONS 3 HOW TO CABLE THE CG-X 3 POWER SUPPLY INSTALLATION 3 OPERATION 3 CARE AND MAINTENANCE
More informationULTIMATE SNAP-N-SEAL
ULTIMATE SNAP-N-SEAL F Series Compression Connectors Thomas & Betts introduces the Ultimate Snap-N-Seal Compression Connector, the newest addition to the Snap-N-Seal system. Look for the classic design
More informationModel LTM-1400 User Manual LTM Multiformat 1x4 Assignment Router / DA. (Component, Y/C, Composite, Balanced Audio, RS422) 2001 Laird Telemedia.
Model LTM-1400 User Manual LTM-1400 2001 Laird Telemedia. CE GENERAL DESCRIPTION The LTM-1400 is a Multi-format Assignment Router/Distribution Amplifier System for the most complex Multimedia signal management.
More informationSONy BID SPECIFICATION FOR POWERED MIXER MODEL NUMBER SRP-X500P
SONy BID SPECIFICATION FOR POWERED MIXER MODEL NUMBER SRP-X500P INSTRUCTIONS: REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST
More informationENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for F Connector, Male, Pin Type
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 124 2011 Specification for F Connector, Male, Pin Type NOTICE The Society of Cable Telecommunications Engineers
More informationZDC RF Coax Connector Series 50 & 75 Ohm
CONTACTORS CONNECTORS WIRE & CABLE EMI/RFI FILTERS CIRCUIT BREAKERS HARNESSING & PROTECTION IDENTIFICATIO I/RFI FILTERS CIRCUIT BREAKERS HARNESSING & PROTECTION IDENTIFICATION & LABELING PCB & CABLE ASSEMBLIES
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR SURVEILLANCE SYSTEM, REMOTE SITE. ITS:CLC 1 of 7 APPR:LWB:DBP: FHWA:APPR:
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR SURVEILLANCE SYSTEM, REMOTE SITE ITS:CLC 1 of 7 APPR:LWB:DBP:07-15-16 FHWA:APPR:07-29-16 a. Description. This work consists of furnishing, installing,
More informationDA1909 COMPUTER VIDEO LINE DRIVER WITH EQUALIZATION USER S GUIDE
MANUAL PART NUMBER: 400-0108-002 PRODUCT REVISION: 1 COMPUTER VIDEO LINE DRIVER WITH EQUALIZATION USER S GUIDE INTRODUCTION Altinex appreciates your purchase of the Line Driver. We are sure you will find
More informationLTC 46xx and LTC 47xx Series Fiber Optic Transmission Units
CCTV LTC 46xx and LTC 47xx Series Fiber Optic Transmission Units LTC 46xx and LTC 47xx Series Fiber Optic Transmission Units Video and data models available No adjustments required Long distance high security
More informationTender Report for Supply and installation of LAN in *Biomedical Imaging and Bioinformatics Lab*
Tender Report for Supply and installation of LAN in *Biomedical Imaging and Bioinformatics Lab* General Scope of Work: Supply and installation of Computer Laboratory setup in MIU Location of Installation:
More informationSECTION 686 VIDEO DECODER DESCRIPTION
686 SECTION 686 VIDEO DECODER DESCRIPTION 686.01.01 GENERAL A. This specification describes the functional, performance, environmental, submittal, documentation, and warranty requirements, as well as the
More informationPassive UTP Transceiver Hub with Integral Camera Power Installation Guide
Passive UTP Transceiver Hub with Integral Installation Guide Models Include: HubSat4D - Four (4) Channel Passive UTP Transceiver Hub with Integral HubSat42D - Four (4) Channel Passive UTP Transceiver includes
More informationMCX - 75 Ohm Connectors
133-8333-001 4 133-8333-401 4 133-8334-001 4 133-8334-401 4 133-8433-001 3 133-8433-101 3 133-8434-001 3 133-8445-001* 3 133-8445-101* 3 133-8701-201 5 133-8701-211 5 133-8701-301 6 133-8701-311 6 133-8701-401
More informationARS x4 MATRIX SWITCHER Instruction Manual
ARS-8400 8x4 MATRIX SWITCHER Instruction Manual Thank you for purchasing one of our products. Please read this manual before using this product. When using this product, always follow the instructions
More informationLTC 4600 and 4700 Series Fiber Optics
CCTV LTC 4600 and 4700 Series Fiber Optics LTC 4600 and 4700 Series Fiber Optics Video and data models available No adjustments required Long distance high security Surface-mount or rack-mount units Video
More informationBILOXI PUBLIC SCHOOL DISTRICT. Biloxi Junior High School
BILOXI PUBLIC SCHOOL DISTRICT Biloxi Junior High School Request for Proposals E-Rate 2014-2015 - Internal Connections Submit Proposals To: Purchasing Department Attn: Traci Barnett 160 St. Peter Street
More informationVGA & Audio over CAT5 Distribution Series
CATS-VGA-12B/CATS-VGA-16B CATS-VGA-RX1/CATS-VGA-RX1D VGA & Audio over CAT5 Distribution Series User Manual CATS-VGA-12B CATS-VGA-RX1 CATS-VGA-16B CATS-VGA-RX1D Safety and Notice The VGA & Audio over CAT5
More informationHN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
More informationCamera Control Unit 55D-BS VOLUME OPEN CABLE MIC OFF GND 2W CAMERA CABLE TALLY. Camera Adapter 55D-CA 9.39" 7.40" 5.2"
The Telemetrics Coax/Fiber Link is an affordable camera control system with increased operating distance. Using frequency multiplexing the following signals are transmitted over a single coaxial cable:
More informationUSER MANUAL. Blackburst, Sync, Audio Tone Generator. For Models BSG-50, RM-50/BSG, SR-50/BSG. Doc Rev. F (C) Copyright 2014
HORITA BSG-50 Blackburst, Sync, Audio Tone Generator USER MANUAL For Models BSG-50, RM-50/BSG, SR-50/BSG Doc. 070450 Rev. F (C) Copyright 2014 P.O. Box 3993, Mission Viejo, CA 92690 (949) 489-0240 www.horita.com
More informationCG-1 CAMERA-GUARD INSTRUCTION BOOK IB647501
CG-1 CAMERA-GUARD INSTRUCTION BOOK IB647501 TABLE OF CONTENTS DESCRIPTION 2 MOUNTING INSTRUCTIONS 2 HOW TO CABLE THE CG-1 2 POWER SUPPLY INSTALLATION 3 OPERATION 3 CARE AND MAINTENANCE 3 APPLICATIONS (WHERE
More informationUSER GUIDE. DM Engineering Multi Station Relay Adapter (MSRA and MSRA-RM) Version DM Engineering
USER GUIDE DM Engineering Multi Station Relay Adapter (MSRA and MSRA-RM) Version 1.35 DM Engineering 2174 Chandler St. Camarillo, CA 91345-4611 805-987-7881 800-249-0487 www.dmengineering.com Overview:
More informationCOMPOSITE VIDEO LUMINANCE METER MODEL VLM-40 LUMINANCE MODEL VLM-40 NTSC TECHNICAL INSTRUCTION MANUAL
COMPOSITE VIDEO METER MODEL VLM- COMPOSITE VIDEO METER MODEL VLM- NTSC TECHNICAL INSTRUCTION MANUAL VLM- NTSC TECHNICAL INSTRUCTION MANUAL INTRODUCTION EASY-TO-USE VIDEO LEVEL METER... SIMULTANEOUS DISPLAY...
More informationSTATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 872 LIGHT EMITTING DIODE TRAFFIC SIGNAL LAMP UNITS JULY 19, 2002
STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 872 LIGHT EMITTING DIODE TRAFFIC SIGNAL LAMP UNITS JULY 19, 02 872.01 Description 872.02 Prequalification 872.03 Material Requirements
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in
More informationLCS 2 RJ 45 Cat. 6A HD panels and units
87045 LIMOGES Cedex Telephone: (+33) 05 55 06 87 87 - Fax: +33 (0)5 55 06 88 88 Page 0 335 85/86 1. General characteristics....1 2. Presentation...1 3. Positioning...1 4. Technical characteristics...1
More informationProfessionally Install Products Right the First Time. TOOL-CRIMP Radial Linear compression tool for BNC, F & RCA connectors
Professionally Install Products Right the First Time Profit with PROFIT Tributaries PROFIT System ProFit System employs radial compression technology which preserves the coaxial cables critical 75 ohm
More informationConcert Series ORDERCODE D3470 ORDERCODE D3471 ORDERCODE D3472 D3470 D3471 D3472
Concert Series ORDERCODE D3470 ORDERCODE D3471 ORDERCODE D3472 D3470 D3471 D3472 Congratulations! You have bought a great, innovative product from DAP Audio. The DAP Audio Concert Series brings excitement
More informationCAT EXT-CAT USER MANUAL
CAT5 8000 EXT-CAT5-8000 USER MANUAL www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday
More informationAMERICAN NATIONAL STANDARD
Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 129 2017 Drop Passives: Bonding Blocks (Without Surge Protection) NOTICE The Society of Cable Telecommunications Engineers (SCTE) Standards
More informationMAXX BOX. MX102/202 Series. MAXX Box
MX102/202 Series MAXX Box MAXX BOX 1 C O N T E N T S SECTION 1: OVERVIEW... 4 Introduction... 4 Description... 4 Ordering Information... 4 Specifications... 5 Environmental... 5 Electrical... 5 Physical...
More informationJul03 Rev C EC
Product Specification Coaxial BNC Solder Receptacle Connector 108-12079 10Jul03 Rev C EC 0990-0940-03 1. SCOPE 1.1. Content This specification covers the performance, tests and quality requirements for
More informationK Service Source. Apple High-Res Monochrome Monitor
K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal
More informationUNM IT/Telecommunications Guide Specification Labeling 11/07/
Labeling 1 PART 1: GENERAL 1.01 SCOPE OF WORK A. Work covered by this Section shall consist of furnishing labor, equipment, supplies, materials, and testing unless otherwise specified, and in performing
More informationVersiVision. FVTM4BCxA-CE / FVRM4BCxA-CE MULTIPLEXER SYSTEM 4-CHANNELS DIGITALLY ENCODED VIDEO 2-CHANNELS BI-DIRECTIONAL DATA
VersiVision FVTM4BCxA-CE / FVRM4BCxA-CE MULTIPLEXER SYSTEM 4-CHANNELS DIGITALLY ENCODED VIDEO 2-CHANNELS BI-DIRECTIONAL DATA 4-CHANNELS BI-DIRECTIONAL AUDIO 4-CHANNELS BI-DIRECTIONAL CONTACT CLOSURE 1-CHANNEL
More informationINFRASTONE BLACKSTONE 10G 6A(U/UTP) Europe, Middle East and Africa regions UNLIMITED USAGE 1
INFRASTONE BLACKSTONE 10G 6A(U/UTP) Europe, Middle East and Africa regions UNLIMITED USAGE 1 WWW.INFRASTONE.COM Contents BLACKSTONE CAT6A U/UTP channel performance Introduction BLACKSTONE CAT6A U/UTP channel
More informationPassive UTP Transceiver Hub with Integral Camera Power Installation Guide
Passive UTP Transceiver Hub with Integral Installation Guide Models Include: HubSat8D - Eight (8) Channels HubSat82D - HubSat8D w/eight (8) HubWayAv Balun/s for s HubSat83D - HubSat8D w/eight (8) HubWayDv
More informationSERIES BNC 50, COAXIAL MINIATURE CONNECTORS
SERIES BNC 50, COAXIAL MINIATURE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER BNC is still one of the most popular connector series, featuring a two stud bayonet coupling mechanism, which is particularly
More informationDUAL/QUAD DISPLAY CONTROLLER Operation Manual
DUAL/QUAD DISPLAY CONTROLLER Operation Manual Model PXD524 MicroImage Video Systems division of World Video Sales Co., Inc PO Box 331 Boyertown, PA 19512 Phone 610-754-6800 Fax 610-754-9766 sales@mivs.com
More informationDA IN 1-OUT LINE DRIVER WITH EQUALIZATION + AUDIO USER S GUIDE
MANUAL PART NUMBER: 400-0430-001 1-IN 1-OUT LINE DRIVER WITH UALIZATION + AUDIO USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL...2 GUIDELINES FOR RACK-MOUNTING...2 INSTALLATION...2
More informationKramer Electronics, Ltd. USER MANUAL. Model: VM Video Component Distributor
Kramer Electronics, Ltd. USER MANUAL Model: VM-1045 Video Component Distributor Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VM-1045 Video Component Distributor
More informationMODEL NUMBER SRP-X700P
BID SPECIFICATION FOR POWERED MIXER / SWITCHER MODEL NUMBER SRP-X700P INSTRUCTIONS: REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO
More informationREQUEST FOR QUOTE: TELECOMMUNICATIONS CABLING Library/Classroom Building, Beltline Campus
REQUEST FOR QUOTE: TELECOMMUNICATIONS CABLING Library/Classroom Building, Beltline Campus PART 1: GENERAL REQUIREMENTS A. Contractor Work 1. Provide and install (except as noted in this document), cable,
More information