Setup Guide. Pandora Pluto. Color Management System. Rev. 1.1
|
|
|
- Alexina Chandler
- 6 years ago
- Views:
Transcription
1 Setup Guide Pandora Pluto Color Management System Rev. 1.1
2 Introduction CalMAN Recommended Workflow CalMAN takes advantage of the Pandora Pluto features to calibrate a video display with a 10-bit 17x17x17 3D cube lookup table (LUT) for SMPTE video level signals. This setup guide assists you in calibrating the Pluto with the CalMAN Color Cube workflow. Color Cube (3D LUT) Pluto Required Firmware Version 1.36 or newer Pluto Control Port Ethernet (use standard straight-through cable) Pluto Initial Setup To set up a Pluto for 3D LUT color calibration: 1. Connect the Pluto signal output to the display to be calibrated. 2. Connect a video input signal to the Pluto. 3. Power on the Pluto. 4. Connect the Pluto and your calibration computer to the same network. 5. Click the left knob on the Pluto front panel. On the video display, record the Pluto IP address at the top of the screen ( default). 6. On your calibration computer, either disable any firewall or create an exception for the Pluto IP address. 7. Rotate the left Pluto knob to select the Setup screen. 8. Set both the Black level and the White level to Full range. Note: The Pluto needs to be set for Full range during 3D LUT calibration, even if you are calibrating for SMPTE range operation, and it must be left in Full range, even for operation in a SMPTE (legal) signal path. 2
3 CalMAN 3D LUT Display Calibration CalMAN can calibrate the 3D LUT in the Pluto with a direct USB control connection. To produce an optimized 3D LUT calibration file and automatically load it into the Pluto: 1. In CalMAN, load the "Color Cube (3D LUT)" workflow. 2. On the CalMAN Settings tab (gear icon), under Workflow Basic Options, select either Video (16-235) [SMPTE legal] or PC (0-255) [Full] to match the intended signal levels to be sent to the display. 3. Proceed through each step of the workflow in the normal fashion, using the following notes for guidance on the indicated workflow pages. 4. On the CalMAN Session Setup page, click the Find 3D LUT Device button, then select "Pandora Pluto (Ethernet). 5. On the Dynamic Range page, adjust the display s black level/brightness control to the black level of the signal content that will be processed through the Pluto (16 for video or 0 for PC/full range). 6. On the RGB Adjust page, under the RGB Adjust Levels selection, select 2 Point 30, 100%. Click Read Continuous and adjust the display s RGB Gain controls for RGB balance at 100%. Adjust the display s RGB Offset/Bias controls (if provided) for RGB balance at 30%. 7. Skip the 1D Ramp LUT page (a 1D LUT does not need to be created). 8. On the 3D Cube LUT page click the AutoCal (rotating arrows) button at the right end of the meter action buttons. The AutoCal Setup dialog then appears (see below). 3
4 Figure X. CalMAN AutoCal Setup dialog, for selecting options for creating a 3D calibration LUT. 1. Under File Path, select the desired directory path and provide a name for the LUT file that CalMAN will create (e.g. monitor ID and date). 2. Under Calibration Type, select the desired type of 3D LUT calibration process. IR Profile (time based): Creates the best quality display calibration 3D LUT possible in the selected period of time. You select how much display quality you have time for, from 30 minutes to maximum display quality (6,000 points max). Uses Intelligent Resolution Profiling to search out the most nonlinear color space areas and correct those first. IR Profile (point based): Creates the best quality display calibration 3D LUT possible with the selected number of measurement points (1,000-10,000 points). Uses Intelligent Resolution Profiling to search out the most nonlinear color space areas and correct those first. Lightning LUT: Creates a display calibration 3D LUT in five minutes or less. Produces a very high quality result on professional displays with moderate linearity. Displays with significant nonlinearity may produce marginal results. 4
5 3. Under Video Range, select SMPTE (16-235) if you are calibrating a video display that clips or compresses signals above reference white, as tested on the CalMAN Dynamic Range page. 4. Click OK. Upon completion of the AutoCal 3D hardware LUT calibration process, CalMAN automatically loads the optimized 33x33x33 LUT calibration data into the Pluto. DONE Pluto 3D LUT calibration and setup is complete. 5
6 CalMAN 3D LUT Display Calibration File Creation for Pluto CalMAN 3D LUT Load to Pluto CalMAN can also create a 3D LUT display calibration file for the Pluto without immediately loading the file into the Pluto. The Pluto does not need to be available during this display calibration and file creation process. The file created will be a.3dl file with the proper Pluto data format for later loading into the Pluto with CalMAN (as detailed below). To create a 3D LUT display calibration file for the Pluto with CalMAN: 1. In the CalMAN main menu, select Open Workflow Template, then select the Color Cube (3D LUT) workflow. 2. On the CalMAN Display Control tab, connect to the SpectraCal Cube Generator as a Display Control device. 3. On the Display Control tab, under File Format, select 3DL common.3dl formats. 4. On the Display Control tab, under File Path, select your desired destination for the.3dl LUT file. 5. On the CalMAN Source Settings tab, select your desired test pattern source for display calibration (this can be the Pandora Pluto, if available). 6. Follow the display calibration instructions in the CalMAN 3D LUT Display Calibration section above. 7. On the AutoCal Setup popup dialog, under Output Cube Size, select 33 Points. Under Bit Depth, select 10. Done: Upon completion of the AutoCal 3D LUT calibration process, CalMAN automatically writes a.3dl file, containing color cube display calibration data, to your selected file destination. This display calibration file can be later loaded to a Pluto, using the procedure in the CalMAN 3D LUT Load to Pluto section below. CalMAN can load a properly formatted 3D LUT file into the Pluto. The LUT needs to be a.3dl LUT file with a bit depth of 10 bits and 33x33x33 data points, with the data points at the following bit levels: 0,32,64,96,128,160,192,224,256,288,320,352,384,416,448,480,512,544,576,6 08,640,672,704,736,768, 800,832,864,896,928,960,992,1023. This.3dl LUT file can be a display calibration LUT created with the CalMAN Cube Generator function (as detailed above). Or, it can be a creative (look) LUT created by any other application (with the proper data points). During the load process, CalMAN converts the.3dl file into the file format required by the Pluto. To load a 3D LUT file into a Pluto: 6
7 1. In CalMAN, on the Display Control tab, connect to the Pluto as a Display Control device. 2. On the Display Control tab, click the Open DDC Window button. 3. On the DDC Controls dialog, scroll to the 3D LUT Controls page. 4. Click the Load LUT File button. 5. In the resulting file navigation window, select the.3dl LUT file that has been created for the Pluto. Done: The selected 3D LUT file is now contained in the Pluto. 7
8 About / Contact About Portrait Displays Portrait Displays, Inc., since 1993, is a leading application software provider (ASP) for PC, smartphone, and tablet displays. The Portrait Displays team now includes SpectraCal, the world s leading provider of video display calibration software. The combined companies offer value-added, feature-rich solutions to both OEM display manufacturers and end users seeking improved accuracy and manageability of their displays. Portrait Displays, an Intel Capital Portfolio company, is a private corporation with headquarters in Pleasanton, California, USA with representatives in Europe, Taiwan, China, Japan, and Korea. Contact Us Submit a Technical Support Request: spectracal.com sales@spectracal.com Portrait Displays, Inc Owens Drive Pleasanton, CA USA portrait.com 8
Setup Guide. Blackmagic Design HDLink Pro. Rev. 1.1
Setup Guide Blackmagic Design HDLink Pro Rev. 1.1 Introduction CalMAN Recommended Workflow CalMAN takes advantage of the Blackmagic Design HDLink Pro features to calibrate a video display with a 10-bit
Setup Guide. SpectraCal ColorBox. (also eecolor) Image Calibration Processor. Rev. 1.1
Setup Guide SpectraCal ColorBox (also eecolor) Image Calibration Processor Rev. 1.1 Introduction CalMAN takes advantage of the SpectraCal ColorBox (also eecolor) processor features to calibrate a video
Setup Guide. Teradek COLR. Rev. 1.1
Setup Guide Teradek COLR Rev. 1.1 Introduction CalMAN Required Version CalMAN takes advantage of the Teradek COLR features to calibrate a video display with a 10-bit 33x33x33 3D cube lookup table (LUT).
Setup Guide. Dolby PRM Rev. 1.1
Setup Guide Dolby PRM-4200 Rev. 1.1 Introduction CalMAN Required Software Version CalMAN Display Calibration Software can automatically create an optimized 3D calibration LUT for the Dolby PRM-4200 monitor.
Setup Guide. AJA Video Systems LUT-box. Rev. 1.2
Setup Guide AJA Video Systems LUT-box Rev. 1.2 Introduction CalMAN Required Version: CalMAN takes advantage of the AJA Video Systems LUT-box features to calibrate a video display with a 10-bit 17x17x17
Setup Guide. Flanders Scientific BoxIO. Rev. 1.1
Setup Guide Flanders Scientific BoxIO Rev. 1.1 Introduction CalMAN Required Version CalMAN takes advantage of the features of the Flanders Scientific BoxIO advanced color management device to calibrate
Setup Guide. Konvision monitors. Rev. 1.0
Setup Guide Konvision monitors Rev. 1.0 Introduction CalMAN Display Calibration Software can automatically create multiple optimized calibration 3D LUTs for the entire line of Konvision monitors, with
Setup Guide. Panasonic BT-4LH310. Rev. 1.1
Setup Guide Panasonic BT-4LH310 Rev. 1.1 Introduction CalMAN Required Software Version CalMAN Display Calibration Software can automatically create an optimized 3D calibration LUT for the Panasonic 4LH310
Setup Guide. Blackmagic Design Teranex Mini. Rev. 1.3
Setup Guide Blackmagic Design Teranex Mini Rev. 1.3 Introduction CalMAN takes advantage of the internal 3D LUT feature of the Blackmagic Design Teranex Mini to calibrate a video display with a 33x33x33
Setup Guide. EIZO Monitors. Rev. 1.4
Setup Guide EIZO Monitors Rev. 1.4 Introduction CalMAN Display Calibration Software can automatically create optimized calibration 1D or 3D LUTs for EIZO monitors equipped with a self-calibration sensor.
Setup Guide. CalMAN Client for SCRATCH. Rev. 1.1
Setup Guide CalMAN Client for SCRATCH Rev. 1.1 Introduction CalMAN Required Software Version: CalMAN Display Calibration Software interfaces directly with ASSIMILATE SCRATCH software through the CalMAN
Setup Guide. Creating 3D LUTs. CalMAN Overview. Rev. 1.1
Setup Guide Creating 3D LUTs CalMAN Overview Rev. 1.1 Introduction This is an overview guide for using the Intelligent Resolution Profiling (IRP), Lightning LUT, and 3D LUT Retargeting technologies that
Setup Guide. Quantum Data 70x/80x Series. Video Generators. Rev. 1.1
Setup Guide Quantum Data 70x/80x Series Video Generators Rev. 1.1 Introduction CalMAN Required Version The Quantum Data 70x and 80x Video Generator test patterns can be automatically controlled by CalMAN
Setup Guide. CalMAN ColorMatch. Rev. 1.1
Setup Guide CalMAN ColorMatch Rev. 1.1 Introduction Thank you for your interest in using the free version of CalMAN ColorMatch. If you haven t already received your free ColorMatch license, follow this
Setup Guide. Panasonic AS800/AX800/AX Models. Rev. 1.1
Setup Guide Panasonic AS800/AX800/AX900 2014 Models Rev. 1.1 Introduction CalMAN Recommended Workflows For the Panasonic models listed above, CalMAN automatically calibrates the display s two point grayscale
Setup Guide. Panasonic. VT30/GT30/DT30, VT50/GT50/WT50/DT50 (EU/UK models) Rev. 1.1
Setup Guide Panasonic VT30/GT30/DT30, VT50/GT50/WT50/DT50 (EU/UK models) Rev. 1.1 Introduction CalMAN Recommended Workflows CalMAN automatically calibrates the Panasonic VT30/GT30/DT30/VT50/GT50/WT50/DT50
Setup Guide. Panasonic VX200/VX300/BT300. Plasma Displays. Rev. 1.1
Setup Guide Panasonic VX200/VX300/BT300 Plasma Displays Rev. 1.1 Panasonic VX200/VX300 (BT300 below) CalMAN Recommended Workflows CalMAN automatically calibrates the Panasonic VX200/VX300 display s two
Setup Guide. Panasonic. VT60/ZT60/WT60/DT60, WT600 (US/Canada) VT60/ZT60/GT60/WT60/DT60/FT60, VT65, WT600 (EU) VT60/WT60/DT60 (NZ/Asia) Rev. 1.
Setup Guide Panasonic VT60/ZT60/WT60/DT60, WT600 (US/Canada) VT60/ZT60/GT60/WT60/DT60/FT60, VT65, WT600 (EU) VT60/WT60/DT60 (NZ/Asia) Rev. 1.1 Introduction CalMAN Recommended Workflows CalMAN automatically
2018 Quick Reference Guide
2018 Quick Reference Guide Introduction CalMAN can guide the calibration of a 2018 LG Super UHD LCD or an 2018 LG OLED TV in HDTV SDR, HDR10, and Dolby Vision modes. This assures the most accurate rendering
Setup Guide. Murideo SIX-G. Digital Video Generator. Rev. 1.6
Setup Guide Murideo SIX-G Digital Video Generator Rev. 1.6 Introduction The Murideo SIX-G digital video generator can be automatically controlled by the CalMAN Display Calibration Software to produce measurement
Setup Guide. SpectraCal MobileForge. Pattern Generator App. Rev. 1.6
Setup Guide SpectraCal MobileForge Pattern Generator App Rev. 1.6 Introduction MobileForge is a free pattern generator app for ios, Android, and Fire TV devices. MobileForge generates accurate test patterns
Setup Guide. Panasonic. VT30/DT30/D30, VT50/WT50 (US/NA models) Rev. 1.1
Setup Guide Panasonic VT30/DT30/D30, VT50/WT50 (US/NA models) Rev. 1.1 Introduction CalMAN automatically calibrates the Panasonic VT30/DT30/D30/VT50/WT50 US/NA model display s two point grayscale controls,
Setup Guide. X-Rite i1display. Retail and OEM. Rev. 1.2
Setup Guide X-Rite i1display Retail and OEM Rev. 1.2 Introduction CalMAN supports the X-Rite i1 Display colorimeter (Retail and OEM) for measuring many display types, including CCFL, LED, plasma, and also
Setup Guide. Color Volume Analysis Workflow. Rev. 1.2
Setup Guide Color Volume Analysis Workflow Rev. 1.2 Introduction Until the introduction of HDR, a video display s color reproduction range was typically represented with a two-dimensional chromaticity
2018 Quick Reference Guide
2018 Quick Reference Guide Introduction This guide designed as a reference to the Sony BRAVIA Workflow, used to calibrate Sony's upper-end Android TVs including Z9D and subsequent LCD and OLED models.
Setup Guide. AV Foundry VideoForge HDMI. Digital Video Generator. Rev. 1.1
Setup Guide AV Foundry VideoForge HDMI Digital Video Generator Rev. 1.1 Introduction The AV Foundry VideoForge HDMI Digital Video Generator is a versatile, high value test pattern generator with a field-ruggedized
Setup Guide. Klein K-10CP Colorimeter. Rev. 1.1
Setup Guide Klein K-10CP Colorimeter Rev. 1.1 Introduction Klein K-10CP Included Parts The K-10CP (Cinema Pro) is a reference class non-contact optical colorimeter with superb accuracy, the fastest read
Setup Guide. SpectraCal C6 HDR2000 Colorimeter. Rev. 1.2
Setup Guide SpectraCal C6 HDR2000 Colorimeter Rev. 1.2 Introduction The SpectraCal C6 HDR2000 Colorimeter is one of the most advanced light measurement devices available, providing the accuracy you need
Calibration Using i1 probe with CalMan and Resolve
20160526 Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA 30005 Phone: +1.678.835.4934 Fax: +1.678.804.1882 E-Mail: Support@FlandersScientific.com www.flandersscientific.com Please
User Manual. Rev. 1.3
User Manual Rev. 1.3 Table of Contents Introduction 3 Important Safety Information 4 Electrostatic Discharge (ESD) Protection 5 Key Features 6 What's in the Box 7 Control & Indicator Functions 8 HDMI System
So, how do I create LUTs for each one of the buttons on the remote?
Advanced Use of Prisma There are several papers and articles on LUTs and calibration that you can find on the Murideo web site. We'll start the discussion here by saying if you choose to optimize and maximize
AV Foundry VideoForge HDMI Digital Video Generator Quick Start Guide
AV Foundry VideoForge HDMI Digital Video Generator Quick Start Guide Thank you for purchasing an AV Foundry VideoForge HDMI Digital Video Generator, a versatile, high value test pattern generator with
FSI Calibration Guide Using I1 / LightSpace / Resolve
FSI Calibration Guide Using I1 / LightSpace / Resolve Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA 30005 Phone: +1.678.835.4934 Fax: +1.678.804.1882 E-Mail: Support@FlandersScientific.com
Using LightSpace CMS for User Created Calibration LUTs
20140130 Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA 30005 Phone: +1.678.835.4934 Fax: +1.678.804.1882 E-Mail: Support@FlandersScientific.com www.flandersscientific.com 1. If
Setup Guide. Rev. 1.7
Setup Guide By Rev. 1.7 Intrductin The SpectraCal VideFrge PRO test pattern generatr can be autmatically cntrlled by the CalMAN Display Calibratin Sftware t prduce measurement and calibratin test patterns
Palette Master Color Management Software
Palette Master Color Management Software How to Use Guide 01 Proprietary Calibration Software Co-developed with leading color calibration experts X-Rite, Palette Master software simplifies calibration
FSI Calibration Guide Using CR100 / LightSpace / BoxIO
FSI Calibration Guide Using CR100 / LightSpace / BoxIO Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA 30005 Phone: +1.678.835.4934 Fax: +1.678.804.1882 E-Mail: Support@FlandersScientific.com
Achieve Accurate Critical Display Performance With Professional and Consumer Level Displays
Achieve Accurate Critical Display Performance With Professional and Consumer Level Displays Display Accuracy to Industry Standards Reference quality monitors are able to very accurately reproduce video,
Achieve Accurate Color-Critical Performance With Affordable Monitors
Achieve Accurate Color-Critical Performance With Affordable Monitors Image Rendering Accuracy to Industry Standards Reference quality monitors are able to very accurately render video, film, and graphics
Calibration Best Practices
Calibration Best Practices for Manufacturers By Tom Schulte SpectraCal, Inc. 17544 Midvale Avenue N., Suite 100 Shoreline, WA 98133 (206) 420-7514 info@spectracal.com http://studio.spectracal.com Calibration
Yellow Frog. Manual Version 1.1
Yellow Frog Manual Version 1.1 1 YellowFrog Contents PC Requirements...... 2 YellowFrog Power Meter Measurement.... 3 YellowFrog PC Software..... 3 Main Screen....... 4 Input Overload....... 5 Battery
What is the history and background of the auto cal feature?
What is the history and background of the auto cal feature? With the launch of our 2016 OLED products, we started receiving requests from professional content creators who were buying our OLED TVs for
First Time Setup Guide
First Time Setup Guide www.exhibio.com 1.877.EXHIBIO (394.4246) Exhibio ST-200 Components & Accessories Standing Mount TV Tuner with Input Cable (USB 2.0 only) VESA Mount Over-the-Air Antenna Power Adapter
More Skills 14 Watch TV in Windows Media Center
M05_TOWN5764_01_SE_SM5.QXD 11/24/10 1:08 PM Page 1 Chapter 5 Windows 7 More Skills 14 Watch TV in Windows Media Center You can watch and record broadcast TV in Windows Media Center. To watch and record
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L HD4112 Manual Rev 1 Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1
Topic: Instructional David G. Thomas December 23, 2015
Procedure to Setup a 3ɸ Linear Motor This is a guide to configure a 3ɸ linear motor using either analog or digital encoder feedback with an Elmo Gold Line drive. Topic: Instructional David G. Thomas December
Projector Management Application Version 7.00 Instruction Guide
Projector Management Application Version 7.00 Instruction Guide Contents 1 INTRODUCTION... 4 1.1 OUTLINE... 4 1.2 SYSTEM... 4 2 INSTALLATION... 5 2.1 SYSTEM REQUIREMENTS... 5 2.2 PROJECTOR MANAGEMENT APPLICATION
ICAC User Manual. ICAC - ( Intelligent Connection for Alignment & Calibration ) Setup Calibration Measurement USO RESTRITO. Version 14.2.
ICAC User Manual ICAC - ( Intelligent Connection for Alignment & Calibration ) Setup Calibration Measurement Version 14.2.1 INDEX 1- Introduction ----------------------------------- 3 2- Structure -------------------------------------
In-situ Port Cal for Dual Carriages Tuner
In-situ Port Cal for Dual Carriages Tuner In-Situ port cal method is the calibration technique mainly for cascaded tuners or multi-carriage tuner. Unlike in-situ system cal which requires 2 VNA calibrations
Operation Guide Version 1.0, December 2015
Operation Guide Version 1.0, December 2015 Document Revision History Revision Date Description v1.0 January 8, 2016 Initial release of COLR Operation Manual, based on firmware version 1.0.1 CONTENTS Contents...
CCE900-IP-TR. User s Guide
CCE900-IP-TR CCE900-IP-T & CCE900-IP-R User s Guide i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com 1. Introduction The CCE900-IP-T & CCE900-IP-R is a solution
Transmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
HD168Bi Quad CVBS/HDMI HD DVBT Encoder Modulator U S E R M A N U A L
HD168Bi Quad CVBS/HDMI HD DVBT Encoder Modulator U S E R M A N U A L Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1 DEVICE Programming
CLIPSTER. 3D LUT File Generation with the Kodak Display Manager. Supplement
Supplement: CLIPSTER 3D LUT File Generation with the Kodak Display Manager (Version 1.0) CLIPSTER 3D LUT File Generation with the Kodak Display Manager Supplement Supplement for the CLIPSTER Documentation:
CHAPTER 3 EXPERIMENTAL SETUP
CHAPTER 3 EXPERIMENTAL SETUP In this project, the experimental setup comprised of both hardware and software. Hardware components comprised of Altera Education Kit, capacitor and speaker. While software
Operation Guide Version 2.0, December 2016
Operation Guide Version 2.0, December 2016 Document Revision History Revision Date Description v1.0 January 8, 2016 Initial release of COLR Operation Manual, based on firmware version 1.0.1 CONTENTS Contents...
Statement SmartLCT User s Manual Welcome to use the product from Xi an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar ). It is our great
LED Display Configuration Software SmartLCT User s Manual Software Version: V3.0 Rev3.0.0 NS110100239 Statement SmartLCT User s Manual Welcome to use the product from Xi an NovaStar Tech Co., Ltd. (hereinafter
Scan Converter Installation Guide
Scan Converter Installation Guide Software on supplied disks Please note: The software included with your scan converter is OPTIONAL. It is not needed to make the scan converter work properly. This software
SXGA096 DESIGN REFERENCE BOARD
SXGA096 DESIGN REFERENCE BOARD For Use with all emagin SXGA096 OLED Microdisplays USER S MANUAL VERSION 1.0 TABLE OF CONTENTS D01-501152-01 SXGA096 Design Reference Board User s Manual i 1. INTRODUCTION...
First Question: Camera head. Lighting unit. Shooting stage
Elmo P30 Visualiser First Question: Q. Is everyone familiar with exactly what a visualiser is? A. A visualiser is effectively a camera on an arm, usually with a shooting stage and its own lighting source.
EAN-Performance and Latency
EAN-Performance and Latency PN: EAN-Performance-and-Latency 6/4/2018 SightLine Applications, Inc. Contact: Web: sightlineapplications.com Sales: sales@sightlineapplications.com Support: support@sightlineapplications.com
Procedures to Characterize Maury s Automatic Tuner Using ATS Software Version 5.1 or above
Procedures to Characterize Maury s Automatic Tuner Using ATS Software Version 5.1 or above Things to check before tuner characterization Make sure tuner is power up and USB cable is connected to the computer
Basic Pattern Recognition with NI Vision
Basic Pattern Recognition with NI Vision Author: Bob Sherbert Keywords: National Instruments, vision, LabVIEW, fiducial, pattern recognition This tutorial aims to instruct the reader on the method used
Footnotes and Endnotes
Footnotes and Endnotes Sometimes when writing a paper it is necessary to insert text at the bottom of a page in a document to reference something on that page. You do this by placing a footnote at the
CobraNet Bundle Assignment Procedure Using CobraNet Discovery
Summary This procedure will allow Q-Sys to integrate with an existing CobraNet system by providing instructions on setting up CobraNet Assignments for the Q-Sys CCN32 CobraNet Card. NOTE: If the CCN32
RDS: The RDS, or Radio Data System, is supported in the g! interface where available.
Manufacturer: Integra Integration Note Model Number(s): Integra 20.3/30.3/40.3/50.3/70.3/80.3 Core Module Version: 5.4 Comments: FW 1.09 (1091-0999-0210-9105) Document Revision Date: 1/15/2013 OVERVIEW
BoxIO User Manual Updated Applies to BoxIO Firmware Version 1.51 IP Remote Utility Version 1.0
BoxIO User Manual Updated 09.25.2017 Applies to BoxIO Firmware Version 1.51 IP Remote Utility Version 1.0 Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA. 30005 Phone: +1.678.835.4934
Reference Guide 2014 ZOOM CORPORATION. Copying or reprinting this manual in part or in whole without permission is prohibited.
Reference Guide 2014 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited. Introduction is a mixer application designed specifically for the. Using a
FS3. Quick Start Guide. Overview. FS3 Control
FS3 Quick Start Guide Overview The new FS3 combines AJA's industry-proven frame synchronization with high-quality 4K up-conversion technology to seamlessly integrate SD and HD signals into 4K workflows.
TelePresence Cisco TelePresence Synch with Edge95MXP - Troubleshooting
TelePresence Cisco TelePresence Synch with Edge95MXP - Troubleshooting THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION,
Optiflex Interactive Video System
Optiflex Interactive Video System Optiflex Interactive Video System 1 Before You Start...............2 On-site Video Surveillance.......6 Touchscreen Interface Viewing...10 Secure Remote Look-in........16
MultiQ Digital signage template system for widescreen monitors
Technical Note MultiQ Digital signage template system for widescreen monitors This document is intended as a guide for users of the MultiQ Digital Signage Template System for widescreen monitors in landscape
Kaleidescape Co-Star for Lumagen
Kaleidescape Co-Star for Lumagen Installation Guide The Co-Star solution allows a Strato movie player to present a unified onscreen library that includes all of a Kaleidescape customer s movies from DVD
Ready. Set. Go make your show. Your guide to creating your first video program with
Ready. Set. Go make your show. Your guide to creating your first video program with TriCaster Mini Go Make Your Show Guide 01 Table of Contents Part 1: Ready. 1) Power, Monitoring and Control 04 2) Bringing
Interface sheet - Korr Cardio Coach Monitor - CPET Ergometer
Interface sheet - Korr Cardio Coach Monitor - CPET Ergometer Service documentation Lode BV Zernikepark 16 NL 9747 AN Groningen The Netherlands t: +31 50 571 28 11 f: +31 50 571 67 46 @: ask@lode.nl www.lode.nl
RELEASE NOTES. Introduction. Supported Devices. Mackie Master Fader App V4.5.1 October 2016
RELEASE NOTES Mackie Master Fader App V4.5.1 October 2016 Introduction These release notes describe changes and upgrades to the Mackie Master Fader app and DL Series mixer firmware since Version 4.5. New
3G-SDI to HDMI Scaler Installation Guide
Introduction 3G-SDI to HDMI Scaler Installation Guide The 3G-SDI to HDMI Scaler allows you to broadcast 3G-SDI signals from one source to two 3G-SDI and one HDMI outputs. Key Features and Benefits Converts
LG Electronics Monitor Proofing System with LG W2420R Display and Adobe Acrobat 8 Professional for GRACoL Coated #1
Off-Press Proof Application Data Sheet LG Electronics Monitor Proofing System with LG W2420R Display and Adobe Acrobat 8 Professional for GRACoL Coated #1 The IDEAlliance Print Properties Working Group
Library ebooks and Your Sony ereader
Library ebooks and Your Sony ereader When using your Sony ereader for the first time to obtain library ebooks and audiobooks, download the Overdrive Media Console, Adobe Digital Editions, and the Sony
How to use EndNote? Training. Faculty of Fisheries and Protection of Waters USB Academic Library of USB March 26, 2015
How to use EndNote? Training Faculty of Fisheries and Protection of Waters USB Academic Library of USB March 26, 2015 EndNote X7 manual http://endnote.com/training/guide/windows What is new in EndNote
Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display.
Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Your Stack ST8961 VS module allows you to synchronize, overlay, and record data available on your Stack
Logic Controls LV3000 VGA Connected Virtual Pole Display
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Logic Controls LV3000 VGA Connected Virtual Pole Display This
2G Video Wall Guide Just Add Power HD over IP Page1 2G VIDEO WALL GUIDE. Revised
2G Video Wall Guide Just Add Power HD over IP Page1 2G VIDEO WALL GUIDE Revised 2016-05-09 2G Video Wall Guide Just Add Power HD over IP Page2 Table of Contents Specifications... 4 Requirements for Setup...
Data Acquisition Instructions
Page 1 of 13 Form 0162A 7/21/2006 Superchips Inc. Superchips flashpaq Data Acquisition Instructions Visit Flashpaq.com for downloadable updates & upgrades to your existing tuner (See the next page for
Reference Guide 2015 ZOOM CORPORATION. Copying or reprinting this manual in part or in whole without permission is prohibited.
Reference Guide 2015 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited. Introduction is a mixer application designed specifically for the. Using a
Dirac Live for Emotiva Automatic Room Correction
Dirac Live for Emotiva Dirac Live for Emotiva Automatic Room Correction ENTER Differential Reference Media Controller TUNER 1 2 3 4 5 6 7 8 VOLUME ------------------------------------------ INPUTS ------------------------------------------
V pro8 QUICK START GUIDE
QUICK START GUIDE Welcome to your V pro8 FIRST STEPS POWERING ON CONNECTING YOUR COMPUTER Thank you for buying the Lawo V pro8, a true high-quality product developed and manufactured in Rastatt, Germany.
Quick Start Guide. Multidimensional Imaging
Quick Start Guide Multidimensional Imaging Printed 11/2012 Multidimensional Imaging Content Quick Start Guide Content 1 Introduction 4 2 Set up multi-channel experiments 5 2.1 Set up a new experiment
VIDEO GRABBER. DisplayPort. User Manual
VIDEO GRABBER DisplayPort User Manual Version Date Description Author 1.0 2016.03.02 New document MM 1.1 2016.11.02 Revised to match 1.5 device firmware version MM 1.2 2019.11.28 Drawings changes MM 2
MXS Strada USER GUIDE
MXS Strada USER GUIDE AiM TECH Srl. Via Cavalcanti, 8 20063 Cernusco S/N (MI) Italia Tel. (+39) 02.9290571 Made in Italy www.aim-sportline.com MXS Strada 01. INTRODUCTION 02. WHAT IS IN THE KIT 03. LAYOUT
Trimble TMX-2050 Display Quick Reference Card
Trimble TMX-2050 Display Quick Reference Card The Trimble TMX-2050 display is a touchscreen platform for precision agriculture. Home screen Left side of screen Right side of screen Tap the buttons on the
User Calibration Software. CM-S20w. Instruction Manual. Make sure to read this before use.
User Calibration Software CM-S20w Instruction Manual Make sure to read this before use. Safety Precautions Before you using this software, we recommend that you thoroughly read this manual as well as the
Interface sheet - Edan ST-1212 Stress - CPET ergometer
Interface sheet - Edan ST-1212 Stress - CPET ergometer Service documentation Lode BV Zernikepark 16 NL 9747 AN Groningen The Netherlands t: +31 50 571 28 11 f: +31 50 571 67 46 @: ask@lode.nl www.lode.nl
FS1-X. Quick Start Guide. Overview. Frame Rate Conversion Option. Two Video Processors. Two Operating Modes
FS1-X Quick Start Guide Overview Matching up and synchronizing disparate video and audio formats is a critical part of any broadcast, mobile or post-production environment. Within its compact 1RU chassis,
Integration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES
Manufacturer: Model Number(s): Minimum Core Module Version: Document Revision Date: Denon Integration Note AVR-2805, 3805, 1613, 1713, 1912CI, 1913, 2112CI, 2113CI, 2310CI, 2311CI, 2312CI, 2313CI, 2808CI,
with the Field-IQ Crop Input Control System
with the Field-IQ Crop Input Control System Quick Reference Card CONNECTING THE SYSTEM Ag25 GNSS antenna (P/N 68040-OOS) TNC/TNC right-angle cable (P/N 50449) Cable assembly, display to Field-IQ (P/N 50449)
The surge protector is located on the floor next to the left plasma tv stand. Just hit the black power button and all equipment should turn on.
IVN Room Layout Turning on the System The surge protector is located on the floor next to the left plasma tv stand. Just hit the black power button and all equipment should turn on. Making a call 1 To
QUICK START GUIDE QT ANALOG HD CAMERA & DVR BUNDLE ENGLISH
QUICK START GUIDE QT ANALOG HD CAMERA & DVR BUNDLE ENGLISH Table of Contents Welcome What s Included...3 Understanding your DVR...4 Get Connected Registration...5 Connect Your Cameras...5 Connect DVR to
Positive Attendance. Overview What is Positive Attendance? Who may use Positive Attendance? How does the Positive Attendance option work?
Positive Attendance Overview What is Positive Attendance? Who may use Positive Attendance? How does the Positive Attendance option work? Setup Security Codes Absence Types Absence Reasons Attendance Periods/Bell
D-Lab & D-Lab Control Plan. Measure. Analyse. User Manual
D-Lab & D-Lab Control Plan. Measure. Analyse User Manual Valid for D-Lab Versions 2.0 and 2.1 September 2011 Contents Contents 1 Initial Steps... 6 1.1 Scope of Supply... 6 1.1.1 Optional Upgrades... 6