REPORT Datum/Date Beteckning/Reference Sida/Page

Transcription

1

2 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 1 Description - Equipment Under Test (EUT) Equipment: Tx Frequency range: Tested Channel: WCDMA Base station transceiver 1900 MHz Single frequency MHz (Block D: MHz) MHz. Product number: TRX PS1, ROJ /1, R1B Serial number: See Hardware list in enclosure 9 RF conducted measurements were done on, TRX PS1, ROJ /1, R1B, s/n A and Amplifier unit / MCPA, KRB 90102/3, R1A, s/n U All RF conducted measurements were done at the output connector J1. EUT configuration: The transmitters were set-up according to Test model 1 in the standard 3GPP TS V5.4.0 ( ). 16 DPCH:s at 30 ksps (SF=128) distributed randomly across the code space, at random power levels and random timing offsets are defined so as to simulate a realistic scenario which may have high PAR (Peak to Average ratio). Manufacturer s representative: Larry Lindström, Ericsson AB Purpose of test The purpose of the tests is to verify compliance with the performance characteristics specified in FCC CFR47. Reservation The test results in this report apply only to the particular Equipment Under Test (EUT) as declared in the report. Delivery of test object The test object was delivered: Test engineers Peter Grahn Jonas Bremholt Fredrik Isaksson Test witnesses Larry Lindström, Ericsson AB Wayne Ly, Ericsson AB

3 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 2 RF Power output measurements according to 47CFR Date Temperature 22 C ± 3 C Humidity 27 % ± 5 % Test set-up and Procedure The measurements were made per 3GPP TS Measurements were made at output connector J1. The output was connected to a Peak power analyser via a 50 ohm attenuator. The RF power was measured with variation in supply voltage at the highest power level. Test was performed on -48 V DC supply voltage system. The transmitter was set up according to Test Model 1 in 3GPP TS during the measurements. Measurement equipment Calibration Due SP number Boonton RF Peak power meter/analyser Boonton Power sensor S/ Multimeter Fluke Testo 610, Temperature and humidity meter Results Nominal power -48 V DC Rated output power level at output connector J1: 43 dbm Transmitter power (dbm) Test conditions Average Block D, MHz T nom 22 C V nom -48 V DC 42.4 T nom 22 C V min V DC 42.4 Measurement uncertainty Limits (according to 3GPP TS ) V max V DC db The deviation of output power shall not be greater than ±2 db of the maximum rated output power. Complies? Yes

4 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 3 Modulation characteristics measurements according to 47CFR Date Temperature 21 C ± 3 C Humidity 37 % ± 5 % Test set-up and Procedure The measurement was made per 3GPP TS Measurements were made at output connector J1. The output was connected to a spectrum analyser. The spectrum analyser was connected to an external 10 MHz reference standard during measurement. The transmitter was set up according to Test Model 1 in 3GPP TS during the measurements. Measurement equipment Calibration Due SP number R&S FSU s/n Multimeter Fluke Testo 610, Temperature and humidity meter Results Nominal Voltage -48 V DC 43 dbm output power at block D ( MHz) Supply voltage DC (V) Test conditions T ( C) Composite EVM (% RMS ) Output J Maximum EVM (% RMS ) Measurement uncertainty % RMS Limits (according to 3GPP TS ) The Error Vector Magnitude (EVM) shall be less than 17.5%. Complies? Yes

5 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 4 Occupied bandwidth measurements according to 47CFR Date Temperature 24 C ± 3 C Humidity 29 % ± 5 % Test set-up and Procedure The measurement test set-up was made per 3GPP TS Measurements were made at output connector J1. The output was connected to a spectrum analyser. The spectrum analyser was connected to an external 10 MHz reference standard during the measurements. The transmitter was set up according to Test Model 1 in 3GPP TS during the measurements. Measurement equipment Calibration Due SP number R&S ESI Testo 610, Temperature and humidity meter Measurement uncertainty: 3.7 db Results Diagram 1 Diagram 2 Diagram 3 Block D ( MHz), OBW Reference level, +43 dbm output power Block D ( MHz), OBW 26 db points, +43 dbm output power Block D ( MHz), OBW Band edge, +43 dbm output power Limits The power of any emission outside the frequency band shall be attenuated below the transmitter power (P) by at least log P db. Complies? Yes

6 F F24 Diagram 1 (3) FCC ID: B5KPROJ Rev Encl. 4.1 RBW 10 MHz RF Att 20 db Ref Lvl VBW 10 MHz 60 dbm SWT 5 ms Unit dbm db Offset A MAX IN1 1MA EXT Center GHz Date: 29.OCT :26:11 10 MHz/ Span 100 MHz

7 F F24 Diagram 2 (3) FCC ID: B5KPROJ Rev Encl. 4.1 Delta 1 [T1] RBW 50 khz RF Att 20 db Ref Lvl 0.12 db VBW 50 khz 60 dbm MHz SWT 6 ms Unit dbm db Offset A MAX 1 1 IN1 1MA 20 EXT Center GHz Date: 29.OCT :31: khz/ Span 6 MHz

8 F F24 Diagram 3 (3) FCC ID: B5KPROJ Rev Encl. 4.1 RBW 50 khz RF Att 10 db Ref Lvl VBW 50 khz 50 dbm SWT 10 ms Unit dbm db Offset A MAX IN1 1MA 10 0 EXT -10 D1-13 dbm F1 F2-50 Center GHz Date: 29.OCT :37:19 1 MHz/ Span 10 MHz

9 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 5 Conducted spurious emission measurements according to 47CFR Date Temperature 22 C ± 3 C 24 C ± 3 C Humidity 27 % ± 5 % 29 % ± 5 % Test set-up and Procedure The measurement was made per ANSI/TIA/EIA Measurements were made at output connector J1. The output was connected to a spectrum analyser. The spectrum analyser was connected to an external 10 MHz reference standard during the measurements. The transmitter was set up according to Test Model 1 in 3GPP TS during the measurements. Measurement equipment Calibration Due SP number R&S ESI Testo 610, Temperature and humidity meter Measurement uncertainty: 3.7 db Results Diagram 1: Output J1, Block D ( MHz), +43 dbm The two highest conducted average emission levels relative to the limit is reported in the table below. Frequency (MHz) Average Amplitude (dbm) Limit (dbm) Yes Yes Limits Compliant The power of any emission outside the frequency band shall be attenuated below the transmitter power (P) by at least log P db. Complies? Yes

10 F F24 Diagram 1 (1) FCC ID: B5KPROJ Rev Encl. 5.1 Ref Lvl 0 dbm 0 RBW 10 MHz VBW 10 MHz SWT 5 ms RF Att 10 db Unit dbm A -10 D1-13 dbm MAX IN1 1MA EXT TDF F2 F1-100 Start 9 khz MHz/ Stop 3 GHz Date: 28.OCT :41:34 Ref Lvl -10 dbm -10 D dbm 2-20 Marker 1 [T1] dbm GHz RBW 10 MHz RF Att 0 db VBW 10 MHz SWT 170 ms Unit dbm 1 [T1] dbm GHz 2 [T1] dbm GHz A MAX IN1 1MA EXT TDF Start 3 GHz Date: 28.OCT :14: GHz/ Stop 20 GHz

11 F F24 1 (3) FCC ID: B5KPROJ Rev Encl. 6 Field strength of spurious radiation measurements according to 47CFR Date Temperature 20 C ± 3 C 21 C ± 3 C 22 C ± 3 C Humidity 27 % ± 5 % 25 % ± 5 % 26 % ± 5 % Test set-up and Procedure The measurement procedure is per ANSI/TIA/EIA The semi anechoic chamber is listed at FCC, Columbia with registration number: The test site also complies with RSS 212, Issue 1, Industry Canada file no. :IC The transmitters were set up according to Test Model 1 in 3GPP TS during the measurements. The measurements were performed with both horizontal and vertical polarisation of the antenna. The antenna distance was 3 m and above 18 GHz the antenna distance was 1 m. A pre-measurement was first performed: In the frequency range 9 k-30 MHz the measurement was performed in field strength. The limit in power, 13 dbm, was recalculated to field strength in free space, 82 dbµv/m. In the frequency range 30 M-20 GHz the measurement was performed in power. A propagation loss in free space was calculated and used as a transducer. The used formula, was, propagation loss = 20 log(4xπxantenna distance/λ). The measurement procedure was as the following: 1. The pre-measurement was first performed with peak detector. The EUT was measured in eight directions and with the antenna at three heights, 1.0 m, 1.5 m and 2.0 m. 2. Spurious radiation on frequencies closer than 20 db to the limit was measured with the substitution method according to the standard. Measurement equipment Calibration Due SP number Anechoic chamber - 15:115 R&S ESI Control computer Software: R&S ES-K1, ver Chase Bilog antenna CBL 6111A EMCO loop antenna EMCO Horn Antenna EMCO Horn Antenna MITEQ Low Noise Amplifier Testo 615, Temperature and humidity meter

12 F F24 2 (3) FCC ID: B5KPROJ Rev Encl. 6 The test set-up during the spurious radiation measurements can be seen in the picture below.

13 F F24 3 (3) FCC ID: B5KPROJ Rev Encl. 6 Results Nominal Voltage -48 V DC Output power: +43 dbm The spurious radiation measured with the substitution method can be found in the table below: Spurious emission level (dbm) Frequency (MHz) RBW Vertical (9k-30MHz: Longitudinal) Horizontal (9k-30MHz: Perpendicular) Hz All emission > 20 db below limit khz All emission > 20 db below limit khz All emission > 20 db below limit MHz All emission > 20 db below limit All emission > 20 db below limit All emission > 20 db below limit All emission > 20 db below limit All emission > 20 db below limit Measurement uncertainty 4.7 db The pre-test emission spectra can be found in encl. 6.1: Diagram 1: Radiated emission 9 k-30 MHz, perpendicular polarization Diagram 2: Radiated emission 9 k-30 MHz, longitudinal polarization Diagram 3: Radiated emission MHz, vertical and horizontal polarization Diagram 4: Radiated emission 1-18 GHz, vertical and horizontal polarization Diagram 5: Radiated emission GHz, vertical and horizontal polarization Limits The power of any emission outside the frequency band shall be attenuated below the transmitter power (P) by at least log P db. Complies? Yes

14 F F24 Diagram 1(5) FCC ID: B5KPROJ Rev Encl Level [dbµv/m] k 20k 40k 100k 300k 1M 2M 4M 10M 30M Frequency [Hz] MES PG _pre PK LIM FCC p2 9k-18G Field FCC p2, field strength 3m

15 F F24 Diagram 2(5) FCC ID: B5KPROJ Rev Encl Level [dbµv/m] k 20k 40k 100k 300k 1M 2M 4M 10M 30M Frequency [Hz] MES PG _pre PK LIM FCC p2 9k-18G Field FCC p2, field strength 3m

16 F F24 Diagram 3(5) FCC ID: B5KPROJ Rev Encl. 6.1 Level [dbm] M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] MES PG _pre PK LIM FCC p2 30M-18G ERP FCC p2, ERP 3m

17 F F24 Diagram 4(5) FCC ID: B5KPROJ Rev Encl. 6.1 Level [dbm] G 2G 3G 4G 5G 6G 8G 10G 18G Frequency [Hz] + MES PG _fin AV MES PG _pre PK LIM FCC p2 30M-18G ERP FCC p2, ERP 3m

18 F F24 Diagram 5(5) FCC ID: B5KPROJ Rev Encl. 6.1 Ref Lvl 0 dbm 0 Marker 1 [T1] dbm GHz RBW 1 MHz VBW 1 MHz SWT 20 ms RF Att 10 db Unit dbm A -10 D1-13 dbm VIEW IN1 1MA TDS Start 18 GHz Date: 15.OCT :11: MHz/ Stop 20 GHz

19 F F24 1 (1) FCC ID: B5KPROJ Rev Encl. 7 Frequency stability measurements according to 47CFR Date Temperature (test equipment) 21 C ± 3 C 21 C ± 3 C 21 C ± 3 C 22 C ± 3 C Humidity (test equipment) 37 % ± 5 % 38 % ± 5 % 39 % ± 5 % 29 % ± 5 % Test set-up and Procedure The measurement was made per 3GPP TS Measurements were made at output connector J1. The output was connected to a spectrum analyser. The spectrum analyser was connected to an external 10 MHz reference standard during measurement. The transmitter was set up according to Test Model 1 in 3GPP TS during the measurements. Measurement equipment Calibration Due SP number Climate chamber R&S FSU s/n Multimeter Fluke Testo 610, Temperature and humidity meter Results Nominal Voltage -48 V DC 43 dbm output power at block D ( MHz) Test conditions Supply voltage DC T ( C) (V) Frequency error (Hz) Output J Maximum freq. error (Hz) 7 Measurement uncertainty < ± 1 x 10-7 Limits (according to 3GPP TS ) The frequency Error shall be within ± 0.05 PPM ( Hz). Complies? Yes

20 F F24 1 (2) FCC ID: B5KPROJ Rev Encl. 8 EUT Hardware configuration list RBS 3202 Position Product name Product number R-state Serial number RBS cabinet /BFE R1B S Door SXK /1650 R1A -- CU Unit BMF /1 R9A SA BB Subrack, BFX /2 R3C S unequipped 26 slots BB subrack fan unit BKV /1 R2A TH4A SCB ROJ /2 R6F T ET-M1 ROJ /2 R7E T Dummy board SXK /1 R3A TUB R0J /3 R4E T Dummy board SXK /1 R3A BBIFB ROJ /1 R2D TE Dummy board SXK /1 R3A RAX ROJ /3 R2A A RAX ROJ /3 R2A A RAX ROJ /3 R2A A Dummy board SXK /1 R2A S Dummy board SXK /1 R2CA S Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A GPB2 ROJ /2 R4H T Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A Dummy board SXK /1 R3A TXB ROJ /3 R1D A

21 F F24 2 (2) FCC ID: B5KPROJ Rev Encl. 8 Position Product name Product number R-state Serial number RF Subrack, BFX /2 R2B S unequipped 16 slots RF subrack fan unit BKV /1 R2A TH4A SCB ROJ /2 R6F T RFIFB ROJ /2 R3E T Dummy SXK /1 R3A TRX PS1 ROJ /1 R1B A Dummy SXK /1 R3A AIU KRC /1 R1A A40003YECM 7 TRX PS1 ROJ /1 R1B A Dummy SXK /1 R3A AIU KRC /1 R1A A40003YHAB 10 TRX PS1 ROJ /1 R1B A Dummy SXK /1 R3A AIU KRC /1 R1A A40003YECE 13 Dummy SXK /1 R3A Dummy SXK /1 R3A Dummy SXK /1 R3A Dummy SXK /1 R2A S AMP Subrack, BFL /1 R1B - - unequipped 6 slots MCPA hub 1 Amplifier unit / MCPA KRB 90102/3 R1A U Dummy Amplifier unit / MCPA KRB 90102/3 R1A U Dummy Amplifier unit / MCPA KRB 90102/3 R1A U Dummy - - AMP subrack fan unit BKV /1 R3A TH4A Power unit Description of EUT Software Revision SWTP 3.7 The EUT is a UMTS Base station configured with three TRX units and three MCPA designed to provide mobile telephone users with a connection to a mobile network or the PSTN.

22 F F24 1 (15) FCC ID: B5KPROJ Rev Encl. 9 Photos RBS 3202 Cabinet, -48 Volt DC system Front view Rear view

23 F F24 2 (15) FCC ID: B5KPROJ Rev Encl. 9 Open door view

24 F F24 3 (15) FCC ID: B5KPROJ Rev Encl. 9 BB Subrack, RF Subrack

25 F F24 4 (15) FCC ID: B5KPROJ Rev Encl. 9 AMP Subrack

26 F F24 5 (15) FCC ID: B5KPROJ Rev Encl. 9 Transceiver Unit, ROJ /1, R1B Front side Top

27 F F24 6 (15) FCC ID: B5KPROJ Rev Encl. 9 Bottom side ID Label FCC ID:

28 F F24 7 (15) FCC ID: B5KPROJ Rev Encl. 9 Main board- PCB component side Main board- PCB rear side

29 F F24 8 (15) FCC ID: B5KPROJ Rev Encl. 9 Amplifier Unit / MCPA, KRB 90102/3, R1A Front side Top

30 F F24 9 (15) FCC ID: B5KPROJ Rev Encl. 9 Bottom side ID label

31 F F24 10 (15) FCC ID: B5KPROJ Rev Encl. 9 FCC ID Printed Board MCPA Radio Control ROA /1 with lid

32 F F24 11 (15) FCC ID: B5KPROJ Rev Encl. 9 Printed Board MCPA Radio Control ROA /1 Backside Printed Board MCPA Radio Control ROA /1

33 F F24 12 (15) FCC ID: B5KPROJ Rev Encl. 9 Backside lid for Printed Board MCPA Radio Control ROA /1 Printed Board MCPA Control Stage 1 ROA /1

34 F F24 13 (15) FCC ID: B5KPROJ Rev Encl. 9 Printed Board MCPA Control Stage 1 ROA /1 Power Ampliflier Block KRY /1 with lid

35 F F24 14 (15) FCC ID: B5KPROJ Rev Encl. 9 Power Ampliflier Block KRY /1 with Printed Board MCPA Second Stage ROA /1 Power Ampliflier Block KRY /1 with Printed Board MCPA Third Stage ROA /1

36 F F24 15 (15) FCC ID: B5KPROJ Rev Encl. 9 Power Ampliflier Block KRY /1 with Printed Board MCPA First Stage ROA /1