Digital Matrix Switcher (Scan converter output board) FDX-32

Transcription

1 RoHS igital Matrix Switcher (Scan converter output board) FX-3 The FX-3 is a highly versatile matrix switcher for V systems with up to 3 inputs and 3 outputs. This HP-compliant matrix switcher can input protected video, and it also can input HMI signals using a conversion cable. The SI input board enables SMPTE 3G/H/S-SI signal input. Using with the HaseT I/O board or optic I/O board makes it easy to establish the system. If using the scan converter output boards, video signals having different synchronization or resolutions can be switched faster than using digital frame synchronizer. The redundant power supplies makes the FX more reliable in mission critical environments. The FX can be controlled remotely over RS-3 and LN ports. Specification Item escription 3 inputs 3 outputs board igital HaseT Optical Up to 8 boards, inputs per board (Up to 3 inputs) SI board igital Up to 8 boards (Up to 3 outputs) HaseT Optical outputs per board (output board) outputs per board (scan converter output board) Functions Scan onverter Motion adaptive interlaced/progressive conversion, spect ratio control, Picture adjustment (brightness, contrast, display position, display size, etc.), Seamless switching with one black frame (*1) Others 3G-SI/H-SI/S-SI input, udio breakaway for independent audio and video switching (When MU-33 (Optional) is connected), I/O board, PU board, and fan unit can be replaced without removing from rack, Preset memory (3 settings), Last memory, Front key function lock, nti-snow(*), onnection Reset(*3), The number of I/Os can be customized, RS-3 transmission (HaseT/Optic output board), Redundant power supply (Optional) Instant lert output 1 port/-pin terminal block/power unit monitoring, Fan unit monitoring External RS-3 1 port/male -sub (9 pin) connector control LN 1 port/rj-5 10ase-T/100ase- (uto Negotiation), uto MI/MI-X Optional (MU-1616) 1 port/female -sub (5 pin) connector Power V ± 10%, 50 Hz/60 Hz ± 3 Hz Without optional / With redundant power supply With HMI/VI I/O board : bout 36 W / 60 W With HaseT I/O board : bout 10 W / 56 W With optic I/O board Multimode fiber : bout 73 W / 57 W Maximum power Singlemode fiber : bout 9 W / 550 W consumption (*) With HMI/VI input/scan converter output board : bout 8 W / 50 W With HaseT input/scan converter output board : bout 387 W / 30 W With optic input/scan converter output board Multimode fiber : bout 0 W / 9 W Singlemode fiber : bout 18 W / 6 W With SI input / HMI/VI output board : bout 30 W / 53 W imensions Without redundant power supply 16.9 (W) x 8.7 (H) x 13.8 () (30 (W) x 1 (H) x 350 () mm) (EI 5U high, full rack wide) (Excluding connectors and the like) Others With redundant power supply 16.9 (W) x 1. (H) x 13.8 () (30 (W) x 310 (H) x 350 () mm) (EI 7U high, full rack wide) (Excluding connectors and the like) Without optional / With redundant power supply With HMI/VI I/O board : 3.6 lbs. (15.7 kg) / 50.7 lbs. (3.0 kg) With HaseT I/O board : 39.5 lbs. (17.9 kg) / 55.8 lbs. (5.3 kg) With optic I/O board Multimode fiber : 5.9 lbs. (0.8 kg) / 6. lbs. (8. kg) Maximum weight Singlemode fiber : 5.9 lbs. (0.8 kg) / 6. lbs. (8. kg) (*) With HMI/VI input/scan converter output board : 36.8 lbs. (16.7 kg) / 53.1 lbs. (.1 kg) With HaseT input/scan converter output board : 39.9 lbs. (18.1 kg) / 56. lbs. (5.5 kg) With optic input/scan converter output board Multimode fiber : 6.7 lbs. (1. kg) / 63 lbs. (8.6 kg) Singlemode fiber : 6.7 lbs. (1. kg) / 63 lbs. (8.6 kg) With SI input / HMI/VI output board : 36. lbs. (16.5 kg) / 5.5 lbs. (3.8 kg) Temperature Operating: 3 F to 10 F (0 to +0 ) Storage: - F to +176 F (-0 to +80 ) Humidity Operating/Storage: 0% to 90% (Non ondensing) ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

2 board specification Item escription HMI/VI input board inputs Video HMI/VI HMI eep olor (*5)/VI 1.0 TMS single link, HP 1. TMS clock: 5 MHz to 5 MHz, TMS data rate: 0.75 Gbps to 6.75 Gbps utomatic input signal equalization, EI emulation VG to QWXG (ot clock: 5 MHz to 165 MHz) * WUXG / QWXG: only Reduced lanking is supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio igital Multi-channel LPM up to 8 channels onnector 1 Female VI-I (9-pin) *nalog signals cannot be used. Transmission distance Up to 98 ft. (30 m) (*6) HaseT input board inputs Video HaseT HaseT (*5) HP 1. (*7) EI emulation VG to QWXG (ot clock: 5 MHz to 165 MHz) * WUXG / QWXG: only Reduced lanking is supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio HaseT Multi-channel LPM up to 8 channels onnector RJ-5 (*8) able T.5E H, at5e UTP/STP, at6 UTP/STP (*9) Transmission distance Up to 38 ft. (100 m) (*10) Optic input board (*11) inputs Video igital optical signal for igital optical signal for (*1) HP 1. EI emulation VG / SVG / XG / WXG (180x768) / WXG (180x800) / Quad-VG / SXG / WXG (1360x768) / WXG (1366x768) / SXG+ / WXG+ / WXG++ / UXG / WSXG+ / WUXG * WUXG: Only Reduced lanking and VI signal are supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio igital optical signal for Multi-channel LPM up to 8 channels able uplex fiber cable, SFP module ( L connectors) (*13) Polishing (*1) SFP for Multimode : P (recommended) SFP for Singlemode: UP (recommended), SP supported *P is not supported Transmission distances (*15) Multimode fiber (OM3): Up to 98 ft. (300 m) Multimode fiber (OM): Up to 0.6 mi. (1 km) Singlemode fiber (OS1) : Up to.9 mi. (.7 km) Singlemode fiber (OS1) : Up to 6.1 mi. (10 km) (Optional) SI input board inputs (With loop-through output) Note: When the FX is powered on, SI input signals are output from SI loop-through output connectors. Video SI 3G-SI/H-SI/S-SI NRZI / NRZ, 0.8 V[p-p] / 75 Ω SMPTE M (3G-SI) / SMPTE 9M (H-SI) / SMPTE 59M- (S-SI) 80i / 576i / 70p / 1080i / 1080p *3G-SI signals: Level and Level *70p: 3.98 Hz and Hz are not supported. udio igital LPM up to 8 channels (Selecting groups of audio groups1 to ) Sampling frequency: 8 khz, Sample size: 16 bit to bit onnector N able 75 Ω coaxial cable for high frequency signal Transmission distances 3G-SI signal input: L-5F 59 ft. (10 m) H-SI signal input: L-5F 787 ft. (0 m) S-SI signal input: L-5V 98 ft. (300 m) The maximum distances may be shorten depending on the quality of cable. Please make sure that the cable is long enough. ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

3 board specification Item escription igital output board outputs Video HMI/VI HMI eep olor (*5)/VI 1.0 TMS signal link, HP 1. TMS clock: 5 MHz to 5 MHz, TMS data rate: 0.75 Gbps to 6.75 Gbps utomatic input signal equalization VG to QWXG (ot clock: 5 MHz to 165 MHz) * WUXG / QWXG: only Reduced lanking is supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio igital Multi-channel LPM up to 8 channels onnector 1 Female VI-I (9-pin) *nalog signals cannot be used. Transmission distance Up to 131 ft. (0 m) (*6) HaseT output board outputs Video HaseT HaseT (*5) HP 1. (*16) VG to QWXG (ot clock: 5 MHz to 165 MHz) * WUXG / QWXG: Only Reduced lanking is supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio HaseT Multi-channel LPM up to 8 channels onnector RJ-5 (*8) able T.5E H, at5e UTP/STP, at6 UTP/STP (*9) Transmission distance Up to 38 ft. (100 m) (*10) Optical output board (*11) outputs Video igital optical signal for igital optical signal for (*1) HP 1. VG / SVG / XG / WXG (180x768) / WXG (180x800) / Quad-VG / SXG / WXG (1360x768) / WXG (1366x768) / SXG+ / WXG+ / WXG++ / UXG / WSXG+ / WUXG *WUXG: Only Reduced lanking and VI signals are supported. 80i / 80p / 576i / 576p / 70p / 1080i / 1080p udio igital optical signal for Multi-channel LPM up to 8 channels able uplex fiber cable, SFP module ( L connectors) (*13) Polishing (*1) SFP for Multimode : P (recommended) SFP for Singlemode: UP (recommended), SP supported *P is not supported Transmission distances (*15) Multimode fiber (OM3): Up to 98 ft. (300 m) Multimode fiber (OM): Up to 0.6 mi. (1 km) Singlemode fiber (OS1) : Up to.9 mi. (.7 km) Singlemode fiber (OS1) : Up to 6.1 mi. (10 km) (Optional) igital scan converter output board outputs (*17) Video HMI / VI HMI eep olor (*18)/VI 1.0 TMS signal link, HP 1. TMS clock: MHz to 0.5 MHz, TMS data rate: Gbps to Gbps utomatic input signal equalization VG / SVG / XG / WXG (180x768) / WXG (180x800) / Quad-VG / SXG / WXG (1360x768) / WXG (1366x768) / SXG+ / WXG+ / WXG++ / UXG / WSXG+ / VESH / WUXG / QWXG * VESH / WUXG / QWXG are output as Reduced lanking. 80p / 576p / 70p / 1080i / 1080p (*19) udio igital Multi-channel LPM up to 8 channels onnector 1 Female VI-I (9-pin) *nalog signals cannot be used. Transmission distance Up to 131 ft. (0 m) (*6) HaseT scan converter output board outputs (*17) Video HaseT HaseT (*18) HP 1. (*16) VG / SVG / XG / WXG (180x768) / WXG (180x800) / Quad-VG / SXG / WXG (1360x768) / WXG (1366x768) / SXG+ / WXG+ / WXG++ / UXG / WSXG+ / VESH / WUXG / QWXG * VESH / WUXG / QWXG are output as Reduced lanking. 80p / 576p / 70p / 1080i / 1080p (*19) udio HaseT Multi-channel LPM up to 8 channels onnector RJ-5 (*8) able T.5E H, at5e UTP/STP, at6 UTP/STP (*9) Transmission distance Up to 38 ft. (100 m) (*10) ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

4 Item escription Optical scan converter output board (*11) outputs (*17) Video igital optical signal for igital optical signal for (*1) HP 1. VG / SVG / XG / WXG (180x768) / WXG (180x800) / Quad-VG / SXG / WXG (1360x768) / WXG (1366x768) / SXG+ / WXG+ / WXG++ / UXG / WSXG+ / VESH / WUXG * VESH / WUXG are output as Reduced lanking. 80p / 576p / 70p / 1080i / 1080p (*19) udio igital optical signal for Multi-channel LPM up to 8 channels able uplex fiber cable, SFP module ( L connectors) (*13) Polishing (*1) SFP for Multimode : P (recommended) SFP for Singlemode: UP (recommended), SP supported *P is not supported Transmission distances (*15) Multimode fiber (OM3): Up to 98 ft. (300 m) Multimode fiber (OM): Up to 0.6 mi. (1 km) Singlemode fiber (OS1) : Up to.9 mi. (.7 km) Singlemode fiber (OS1) : Up to 6.1 mi. (10 km) (Optional) *1 Seamless switching with a black frame. * The anti-snow feature automatically fixes snow noise that is a specific symptom of HP-compliant signals and mainly occurs at start-up. This feature does not work when snow noise has already occurred during startup or when it occurs due to a bad condition of the transmission line. *3 For digital systems, some problems, such as an HP authentication error, can often be recovered by physically disconnecting and reconnecting the digital cables. However, the onnection Reset feature will fix these problems automatically without the need to physically plug and unplug the cables. It creates the same condition as if the cable were physically disconnected and reconnected. This feature only works for the FX s output. If other devices are connected between the FX s output and sink device, this feature may be invalid. * Please contact our Sales ivision for power consumption information of each configuration. *5 36 bit/pixel (1 bit/component) eep olor is supported while x.v.olor, 3, R, HE, and E are not supported. *6 The maximum cable distance varies depending on the connected devices and was measured under following conditions: IK s WG cable was used and 1080p@60 bit/pixel (8 bit/component) signals were transmitted. The maximum cable distance depends on the connected devices. The distance may not be extended with some device combinations, cabling method, or other manufacturer s cable. Video may be disturbed or may not be output even if signals are within the range mentioned above. *7 HaseT input: VI signals protected by HP are not supported. To transmit those signals, use an IK s twisted pair cable extender supporting VI signals. *8 RJ-5 (HaseT connector) is only for extending digital video and audio signals over a at5e/at6 twisted pair cable. Use it with IK s twisted pair cable transmitter or receiver. o not use for LN devices. *9 T568 or T568 straight. The T.5E H cable is developed by IK and recommended by HaseT alliance. *10 The maximum distance was obtained when IK s T.5E H cable was used. The distance may not be extended with some device combinations, cabling method, or other manufacturer s cable. Video may be disturbed or may not be output even if signals are within the range mentioned above. Operations may not be stable with some L devices; please check the operation beforehand or contact us. The maximum distance is the shorter distance of connected HaseT product or sink device s maximum distance. *11 The IK OPF-H1000- must be connected for optical input and output cards. *1 eep olor, x.v.olor, 3, R, HE, and E are not supported. *13 Please refer to SFP Specification. *1 It is possible to connect without using the recommended polishing method, but that may cause a change of distance ability due to an increase in return loss. *15 The maximum distance is measured under the following conditions: Fiber that is polished by a recommended method is used, there is no interconnection, and the allowable bending radius is not exceeded. *16 HaseT output: VI signals protected by HP are not supported. To transmit those signals, use an IK s twisted pair cable receiver supporting VI signals. *17 Scan converter output board uses of channels. hannel numbers are assigned to each connector consecutively. hannel number for unused channel is reserved but not be able to set. *18 30 bit/pixel (10 bit/component) eep olor is supported while x.v.olor, 3, R, HE, and E are not supported. * p and 1080i are 50 Hz/59.9 Hz. SFP Specification Item Multimode fiber Singlemode fiber Wave length 850 nm (Oxide VSEL laser (*)) 1310 nm (Fabry-Perot laser (*)) Max. distance OM3: 300 m, OM: 1 km OS1:.7 km Receiver sensitivity -13 dm or longer -18 dm or longer verage Launch Power -9 dm to -.5 dm -8. dm to -3 dm Max. input power 0 dm +0.5 dm onnector L (uplex) * The lasers in these models meet class1. If SFP is for Singlemode fiber, we have modules which can extend up to 6.1 mi. (10 km). (OS1) ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

5 MENU /SET ES MENU /SET ES SWITHING MOE V& VIEO UIO SWITHING MOE V& VIEO UIO LO PRESET LO PRESET 1 ~ 1~ 1 ~ 1~ VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) UPTE LRM HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL SI SI SI SI SI SI SI SI UPTE LRM 100-0V REKER VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL SI SI SI SI SI SI SI SI REKER 100-0V VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) 100-0V VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) REKER VI-(HMI) HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT OPTIL OPTIL OPTIL OPTIL OPTIL OPTIL 1 ~ 1~ 1 ~ 1~ Front & Rear Panels RS-3 LN IGITL MTRIX SWITHER FX-3 OFF LL SET Without redundant power supply UNIT 1 UNIT RS-3 LN IGITL MTRIX SWITHER FX-3 OFF LL SET With redundant power supply ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

6 RoHS iagram igital Matrix Switcher (Scan converter output board) FX-3 iagram and Features Up to 3 inputs/8 boards FX-3 Up to 3 outputs/8 boards igital output board outputs/1 board EQ Up to 131 ft. (0 m) igital video/audio HMI VI igital video/audio HMI VI Up to 98 ft. (30 m) igital input board inputs/1 board EQ Receiver EI emulator HaseT output board outputs/1 board Up to 38 ft. (100 m) igital video/audio/ HaseT igital video/audio for HaseT igital video/audio for Optical fiber Up to 38 ft. (100 m) (*1) HaseT input board inputs/1 board Receiver EI emulator Optical input board inputs/1board Receiver EI emulator Video/audio matrix switch 3IN- 3OUT Optical output board outputs/1 board igital scan converter output board outputs/1 board Scan converter EQ (*1) igital video/audio/ Optical fiber Up to 131 ft. (0 m) igital video/audio HMI VI SI video/audio 3G-SI H-SI S-SI SI video/audio 3G-SI H-SI S-SI (*) Loop-through (*1) Multimode fiber OM3: Up to 98 ft. (300 m) OM: Up to 0.6 mi. (1 km) Singlemode fiber OS1: Up to.9 mi. (.7km) SI input board inputs/1 board Receiver able driver HaseT scan converter output board outputs/1 board Scan converter Optical scan converter output card outputs/1 board Scan converter Up to 38 ft. (100 m) (*1) igital video/audio/ HaseT igital video/audio/ Optical fiber (*) 3G-SI: Up to 59 ft. (10 m) H-SI: Up to 787 ft. (0 m) S-SI: Up to 98 ft. (300 m) * board can expand in -input unit. * board can expand in -output unit. * Scan converter output board can expand in -output unit. Ordering code FX-3 16T8MMS-1T1MMSM-P : igital input / output slot board S: igital scan converter output slot board T: HaseT input / output slot board TS: HaseT scan converter output slot board MM: Multimode fiber optical input / output slot board MMS: Multimode fiber optical scan converter output slot board SM: Singlemode fiber optical input / output slot board SMS: Singlemode fiber optical scan converter output slot board LS: Singlemode fiber (6.1 mi. (10 km)) optical input / output slot board LSS: Singlemode fiber (6.1 mi. (10 km)) optical scan converter output slot board S: SI input slot board P: Redundant power supply 9 1 : The number of digital inputs : The number of HaseT inputs 3 : The number of multimode optical inputs : The number of singlemode optical inputs 5 : The number of digital outputs 6 : The number of HaseT outputs 7 : The number of multimode optical outputs 8 : The number of singlemode optical outputs Ex.) 16 inputs outputs: 8 digital inputs / HaseT inputs / singlemode optical inputs digital scan converter outputs / 16 HaseT outputs / singlemode optical outputs (6.1 mi. (10 km)) FX-3 8TSM-ST16LS ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3

7 [Features] Video Up to 1080p/QWXG*1 (R)* 3G-SI/H-SI/S-SI input utomatic input signal equalization : Up to 98 ft. (30 m) : Up to 131 ft. (0 m) Up to 38 ft. (100 m) over at6 cable Transmission distance over fiber optic cable Multimode fiber (OM3) : Up to 98 ft. (300 m) Multimode fiber (OM) : Up to 0.6 mi. (1 km) Singlemode fiber (OS1) : Up to.9 mi. (.7 km) (up to 6.1 mi. (10 km), optional) nti-snow The number of I/Os can be customized Scaling (Scan converter output board) SI Loop-through output connector ontrol input RS-3 LN Others EI emulation udio breakaway for independent audio and video switching When MU-33 (Optional) is connected I/O board, PU board, and fan unit can be replaced without removing from rack larm output (Monitoring power source and fans) Preset memory Last memory onnection Reset Front key function lock Redundant power supply RS-3 transmission (HaseT/Optic output board) *1 * Maximum resolution of optic I/O board: WUXG (R) (R)=Reduced lanking Video/audio input RS-3 VI LN REKER lank period will be happen when FX switches input channel V LRM UPTE 1 Video/audio output VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) 1 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) IN5 IN1 VI-(HMI) VI-(HMI) HaseT HaseT HaseT VI-(HMI) VI-(HMI) HaseT VI-(HMI) VI-(HMI) HaseT P HaseT HaseT HaseT HaseT HaseT HaseT HaseT HMI/VI OPTIL OPTIL OPTIL OPTIL HaseT HaseT HaseT HaseT 1 OPTIL OPTIL OPTIL HaseT SI HaseT HaseT HaseT 1 OPTIL SI SI SI SI OPTIL OPTIL OPTIL OPTIL SI SI SI SI OPTIL OPTIL OPTIL OPTIL Industrial video device L monitor FX-3 Video/audio input lank period become shorten RS-3 LN VI REKER 100-0V LRM UPTE 1 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) Video/audio output VI-(HMI) VI-(HMI) VI-(HMI) 1 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) IN1 IN5 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) HaseT HaseT HaseT HaseT P HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HMI/VI HMI/VI OPTIL OPTIL OPTIL OPTIL HaseT HaseT HaseT HaseT 1 OPTIL OPTIL OPTIL HaseT SI HaseT HaseT HaseT 1 OPTIL SI SI SI SI OPTIL OPTIL OPTIL OPTIL SI SI SI SI OPTIL OPTIL OPTIL OPTIL Industrial video device igital frame synchronizer L monitor FX-3 lank period become shorten Video/audio input RS-3 LN VI REKER 100-0V LRM Video/audio output UPTE 1 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) IN5 IN1 1 VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) VI-(HMI) HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT HaseT P HMI/VI OPTIL OPTIL OPTIL OPTIL HaseT HaseT HaseT HaseT 1 OPTIL OPTIL OPTIL OPTIL HaseT HaseT 1 SI SI SI SI SI OPTIL OPTIL OPTIL OPTIL SI SI SI SI OPTIL OPTIL Industrial video device igital frame synchronizer L monitor FX-3 uilt-in digital frame synchronizer ll specifications and drawings are subject to change without notice. lu-ray isc and lu-ray is a trademarks of lu-ray isc ssociation. Please do not use the supplied adapter and power supply cable for other products. The terms HMI and HMI High-efinition Multimedia Interface, and the HMI Logo are trademarks or registered trademarks of HMI Licensing dministrator, Inc. in the United States and other countries. PJLink is a trademark in Japan, the United States, and other countries/regions. HaseT and the HaseT lliance Logo are trademarks of the HaseT lliance. The terms nti-snow and onnection Reset are registered trademarks of IK orporation in Japan ll other IK orporation FX-3