LCD TV Owner's Manual

Transcription

1 LCD TV Owner's Manual FPE3000 Before operating the unit, please read this manual thoroughly

2 Contents Congratulations on your purchase of this LCD TV. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this LCD TV. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Contents Important safety cautions...5 Identification of controls...8 Antenna connection Installation...13 Menu introduction...19 Turning On/Off / Selecting input signal...21 Operations in TV mode...22 Channel Preset...22 Channel Select...23 Picture adjustment...24 Sound adjustment... System Setup...26 Timer setting...28 CCD setting...29 V-chip setting...30 Adjustment in YPbPr mode...32 Adjustment in PC mode...33 Troubleshooting...35 Specifications

3 3

4 4

5 Important Safety Cautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Do not expose this unit in the rain or spatter by liquid. Do not use this product near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Do not use immediately after moving from a low temperature to high temperature environment, as this causes condensation, which may result in fire, electric shock, or other hazards. Heat sources-keep the product away from heat sources such as radiators, heaters, stoves and other heat generating products (including amplifiers). Requirement of environment temperature: o o o o 20 C~50 C for storage; 0 C~40 C for working The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not place the product on an unstable trolley, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a trolley, stand, tripod, and bracket or table recommended by the manufacturer or sold with the product. 5

6 This TV set operates on power of 120V, 60Hz. You must not use a power supply of any other type. When relocating the product placed on a trolley, it must be moved with the utmost care. Sudden stops, excessive force and uneven floor surfaces can cause the product to fall from the trolley. The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product. Powersupply cords should be routed so that they are not likely to be walked on or snagged by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product. If the power cord or the plug is damaged contact a qualified service department for service. Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock. High Voltage exists in this TV set. Do not remove the cover. In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or impacted upon by other objects. Be careful not to be injured by broken glass pieces in case the LCD panel breaks. Don't try to push anything into the cabinet or place any vessel with water on the TV set. For added protection for this television equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due to lightning and power-line surges. 6

7 7

8 Identification of controls Front Remote sensor On/Standby Indicator Light SOURCE MENU CH CH VOL VOL POWER To enter into MENU Channel up Volume up To select input signal Channel down Volume down Power on/ Standby 8

9 VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L R L Back AV HDTV VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V ANT IN PHONE LINE IN +12V R L R L +5V R L AV HDTV Video input S-video input DVD input (480i) HDTV YPbPr inputs (480p, 720p,1080i) VGA input Antenna input Earphone jack DC input from power supply Speaker outputs PC audio line in Audio inputs HDTV Audio inputs 9

10 Identification of controls(continued) Remote Control power on/standby Volume down To enter into MENU Colour/ sound system select Zoom mode select Auto correct picture Picture mode select Sound mute Channel up Volume up Channel down To exit/selectosd menu Sleep timer Clock/Timer setting Previous channel (recall) On-screen display (info) Keypad Video Input select Still picture OSD position select Adjusting Bass To select MONO/SAP/ STEREO (TV only) Adjusting Treble 10

11 Battery installation Effective remote range Please install the batteries before using the remote control unit. 1 Open the battery cover FT Install two "AAA" batteries matching the +/- polarities of the battery to the +/- marks. 3 Notes: Replace the battery cover. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. Do not throw the batteries into a fire. Dispose of used batteries in the specified manner. Do not drop, dampen or disassemble the remote control. Notes: There should be no obstacle between the TV and the transmitter. Use the remote control within the effective range as the above figure. If the remote control does not work, please check whether the batteries are exhausted or the polarity is wrong. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV, the remote operation may be unstable. 11

12 VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L AV HDTV R L Antenna connection CABLE TV (CATV) CONNECTION A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75- ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. Terminal. Some cable TV companies offer "premium pay channels". Since the signals of these premium pay channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/descrambler is necessary for normal viewing of the scrambled channels. For more specific instructions on installing cable TV, consult your cable TV company. One possible method of utilizing the converter/descrambler provided by your cable TV company is explained below. Please note: An RF switch provided with two inputs (A and B) is required (not supplied). RF switch (not supplied) OUT IN Cable TV converter/ descrambler (not supplied) Two-set signal splitter (not supplied) Cable TV Line "A" position on the RF switch (not supplied) : You can view all unscrambled channels by using the TV's channel keys. "B" position on the RF switch (not supplied) : You can view the scrambled channels via the converter/descrambler by using the converter's channel keys. Note: Consult your Dealer or Service Center for the type of splitter, RF switch or combiner that might be required. ANTENNAS The antenna requirements for good color television reception are more important than those for black & white television reception. For this reason, a good quality outdoor antenna is strongly recommended. The following is a brief explanation of the type of connections that are provided with the various antenna systems. 1. A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (not supplied). 2. A 300-ohm system is a flat "twin-lead" cable that can be attached to a 75-ohm terminal through a ohm adapter (not supplied). F-type connector 75-ohm coaxial cable (round) 300-ohm twin-lead cable (flat) OUTDOOR ANTENNA CONNECTION Use one of the following two diagrams if you connect an outdoor antenna. A: Using a VHF/UHF combination outdoor antenna. B: Using separate VHF and/or UHF outdoor antennas. Connect the outdoor antenna cable lead-in to the ANT. terminal on the rear of the TV set. VHF/UHF antenna A. Combination VHF/UHF Antenna 300-ohm twin-lead 300/75-ohm adapter (not supplied) or VHF/UHF antenna 75-ohm coaxial cable Antenna cable B. Separate VHF and/or UHF Antennas 300-ohm twin-lead UHF antenna VHF antenna Combiner (not supplied) OUT IN 300-ohm twin-lead 75-ohm coaxial cable or 12

13 VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L R L Installation Power connection Before using this equipment, please connect the AC power adapter correctly. 2 AV HDTV Plug into AC outlet. Household power outlet AC cord 1 AC power adapter 1. Connect the female plug to the AC socket on AC adapter. 2. Connect the AC adapter to the DC power input of the set. 3. Connect the male plug to the wall outlet as illustrated. Notes: This product should be operated only from the type of power source indicated on the marking label. Always unplug the AC adapter from the product and power outlet when not using for a long period of time. 13

14 Installation(continued) Connecting video/audio equipment VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V ANT IN PHONE LINE IN +12V R L R L +5V R L AV HDTV To S-video input R W To audio inputs To video input Y R w To audio inputs Y W R Yellow (video) white (audio L/MONO) red (audio R) To ANT input w R To audio outputs VHS Video equipment with S-video terminal To video output Y w To audio outputs R VHS To ANT output To ANT output Video equipment without S-video terminal 14

15 VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA ANT IN PHONE LINE IN R L R L AV HDTV R L Installation(continued) Connecting DVD player and speakers VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V ANT IN PHONE LINE IN +12V R L R L +5V R L AV HDTV Red Black Red To YCbCr G inputs B R R w To audio inputs To speaker To speaker To YCbCr outputs G B R R w To audio outputs DVD DVD Player W R G B White (audio L/MONO) Red (audio R, Cr) Green (Y) Blue (Cb) 15

16 Installation(continued) Connecting YPbPr terminals VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V ANT IN PHONE LINE IN +12V R L R L +5V R L AV HDTV To YPbPr inputs G B R R w To audio inputs W White (audio L/MONO) R Red (audio R, Pr) G Green (Y) B Blue (Pb) To YPbPr outputs (480p/720p/ 1080i) G B R R w To audio outputs SET TOP BOX (Or other equipment with YPbPr output terminals) 16

17 Installation(continued) Connecting VGA interface VIDEO L S-VIDEO Y Cb Cr Y Pb Pr VGA DC +24V ANT IN PHONE LINE IN R L R L +12V +5V R L AV HDTV To VGA input interface To LINE in Equipment with VGA output interface To LINE out To VGA output interface 17

18 Installation(continued) Elevation adjustment You can adjust the angle of the LCD TV as follows. o o The elevation can be adjusted from -5 to

19 Menu Introduction Press MENU button to call up menu, press MENU button repeatedly to select different menu pages. In MENU operations, the CH / buttons are used to select item upwards or downwards; the VOL+/- buttons are used to Menu overview in TV mode PICTURE setting menu PICTURE SETTING Brightness Contrast Color Sharpness Tint To adjust the picture's brightness. To adjust the picture's contrast. To adjust the picture's color saturation. To adjust the picture's sharpness. To adjust the picture's skin color. SOUND menu SOUND Bass Treble Balance MTS MONO To adjust the Bass. To adjust the Treble. To adjust the Balance. To select STEREO, SAP or MONO (TV mode only). Color sys Language OSD position OSD background SETUP menu SETUP AUTO Eng Upper Left Opaque To select color system.(it is unaccessible in TV mode) To select OSD menu language. To select OSD menu position. To set OSD background texture. CHANNEL SETTING menu Auto search Source Current Prog Skip Auto fine tune CHANNEL SETTING Antenna 12 ON OFF To start auto search of valid channels. To select antenna input or cable input To display current channel number. To add or skip current channel. To turn on or turn off auto fine tune. 19

20 Menu Introduction(continued) CCD and Vchip settings menu (in TV mode) CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings Off Transparent Press to switch between Caption, text and TV modes for Closed-Captioned programs. To select background for CCD display. Input a password to enter into Vchip menu. Input the password MPAA Rating Sys... Vchip menu RATING SETTING TV Block Settings... Change Password... <LEFT> or <RIGHT> change, <Menu> return MOVIE RATING Rating MPAA G MPAA PG MPAA PG-13 MPAA R MPAA NC-17 MPAA X A/B A A A A A A <UP/DOWN>move, <LEFT/RIGHT>change TV RATING Rating A/B FV V S L D TV-Y TV-Y7 TV-G TV-PG A B A A A A A A TV-14 A A A A A TV-MA A A A A <LEFT/RIGHT>move, <UP/DOWN>change, <Menu>return CHANGE PASSWORD New Password: New Password Validate: Ok Cancel <LEFT/RIGHT> move, <Menu> return, <Enter> execute 20

21 Turning On/Off / Selecting input signal TV Turning On 1. Connect the power, the red indicator lights up, the set is in STANDBY mode. 2. Press the POWER button on the unit's control panel or the button on the remote control to turn the set on. Turning Off With the power on, press the POWER button to turn off the set, and the set is in standby mode. * Always unplug the AC adapter from the product and power outlet when not using for a long period of time. Notes: This TV set can automatically turn off by: 1. When there is no TV signal input for about 15 minutes; 2. Sleep timer. Selecting input signal 1. Press the button on the remote control or SOURCE button on the set's panel to select input mode. You can select TV, AV, S-video, YCbCr, YPbPr or PC. 2. If you want to go to TV mode, press button repeatedly to select TV mode. 3. Press DSP button, the screen display current mode. Press ENTER to cancel OSD. 21

22 Operations in TV mode Channel Preset Auto search Source Current Prog Skip Auto fine tune CHANNEL SETTING Antenna 12 ON OFF To enter into CHANNEL SETTING menu 1. Press MENU button repeatedly to display CHANNEL SETTING menu. 2. Press CH or CH button to select item. 3. Press VOL+ or VOL- button to confirm or adjust selected item. Antenna / Cable selection Enter into CHANNEL SETTING menu and select Source item. Press VOL- or VOL+ button to select Antenna or Cable. Antenna: If using a VHF/UHF antenna (2-68). Cable: If using Cable TV (2-1). Auto search Source Current Prog Skip Auto fine tune CHANNEL SETTING Antenna 12 ON OFF Auto Search Please enter into CHANNEL SETTING menu and select Auto Search item. Press VOL- or VOL+ button to start Auto Search and all active programs will be memorized. During the process of Auto Search, pressing MENU button will stop Auto Search. Adding and skipping channels Antenna Auto searching 28 VHFL Press <Menu> to escape After auto search, you can add or skip channels as follows: Select a channel to be added or skipped by direct channel select buttons. Enter into CHANNEL SETTING menu and select Skip item. Press VOL- or VOL+ button to select On or Off. Skip On: To skip the current channel. Skip Off: To add the current channel. Auto search Source Current Prog Skip Auto fine tune CHANNEL SETTING Antenna 12 ON OFF * To exit the menu, press ENTER button. Fine tuning In area of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use Fine tuning. Use 0~9 digit buttons or CH / buttons to select the desired channel, then enter into CHANNEL SETTING menu and select Auto fine tune item. Press VOL+ button to select ON to activate the auto fine tune. Auto search Source Current Prog Skip Auto fine tune CHANNEL SETTING Antenna 12 ON OFF 22

23 Channel Select 8 Use 0-9 digit buttons Use 0-9 digit buttons to select one-digit channel number. Press 0-9 button - -5 Press ENTER button 5 To select two-digit channel: Press 0-9 button - -5 Press 0-9 button -51 Press ENTER button 51 To select three-digit channel: Press 0-9 button - -1 Press 0-9 button -11 Press 0-9 button 110 Note: the period of two-press should be within 3 seconds. Use CH / button Press CH button, the channel number increases; Press CH button, the channel number decreases. Use previous channel button Press this button to switch between the current channel and previous channel. 23

24 Picture adjustment Brightness Contrast Color Sharpness Tint PICTURE SETTING Adjusting picture 1. Press MENU button to display PICTURE SETTING menu. 2.Press CH / button to select item. Item VOL- VOL+ Brightness darker lighter Contrast weaker stronger Color paler deeper Sharpness softer sharper Tint purplish greenish The adjusted settings are stored in the User mode. There are three preset picture modes and one User-set picture mode. Press the P.M button to select a picture mode according to your favorites. 4. Press P.M button to select picture mode. You can quickly select picture mode by P.M button. There are four picture mode: Bright, Standard, Mild and User mode. Bright: Select for a bright picture. Standard: Select for a normal picture. Mild: Select for a fine/soft picture. Adjusted settings are stored in User mode. Using STILL button You can still current screen picture by pressing STILL button on the remote. Using AUTO.ADJ button Press AUTO.ADJ button on the remote to adjust picture for best viewing. * To exit the menu, press ENTER button. 24

25 Sound adjustment Bass Treble Balance MTS SOUND MONO Adjusting Sound 1. Press MENU button repeatedly to display SOUND menu. 2.Press CH / button to select item. Item VOL- VOL+ Bass Treble weaker weaker stronger stronger Balance decreases the decreases the right channel left channel MTS Notes: MONO/SAP/STEREO You can quickly adjust Bass and Treble by using Bass+/ Bassand Treb+/Treb- buttons on the remote. You can quickly select audio mode by MTS button. MONO STEREO (If the program is STEREO) MONO SAP (If the program is SAP) MONO STEREO SAP (If the program is STEREO & SAP) Adjusting Volume You can use VOL+ or VOL- button to adjust volume. Press VOL+ button, the volume increase; Muting the sound If you want to mute the sound, press button on the remote. To resume the sound, press this button again or you can also press VOL+ or VOL- to resume the sound. * To exit the menu, press ENTER button.

26 System setup Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque To enter into SETUP menu 1. Press MENU button repeatedly to display SETUP menu. 2. Press CH or CH button to select item. 3. Press VOL+ or VOL- button to confirm or adjust selected item. Color system In AV mode, you can select color system. From the SETUP menu, press CH / to select Color sys item. Press VOL- or VOL+ button to select a proper color system according to the program type. Normally, select AUTO. Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque You can quickly access Color system menu bar by C.SYS *This is an advanced setting and should not be touched. Setting OSD Language From the SETUP menu, press CH / to select Language item. Press VOL- or VOL+ button to select the desired language. Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque * To exit the menu, press ENTER button. 26

27 System setup(continued) Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque Setting OSD position From the SETUP menu, press CH / to select OSD position item. Press VOL- or VOL+ button to select an OSD position in your preference. Notes: You can quickly select OSD menu position by using OSD POSITION button on the remote. Setting OSD Background From the SETUP menu, press CH / to select OSD Background item. Press VOL- or VOL+ button to select Opaque or Translucent. Color sys Language OSD position OSD background SETUP AUTO Eng Upper Left Opaque Setting Scaler mode This unit allows you to adjust screen aspect ratio in your preference. Press ZOOM button on the remote to select a proper screen aspect ratio. Anamorphic, 4:3 and Panorama can be selected. Anamorphic Notes: You can quickly select screen ratio by using ZOOM button on the Remote Control * To exit the menu, press ENTER button. 27

28 Timer setting Use SLP button Turn off 0 Press SLP button repeatedly to set sleep time between: 0, 10, 20, 30, 60, 90,120,180,240 minutes. If you select 0 minute, it means the sleep timer function is turned off. Use CLK button Press CLK button, the Current time menu bar appears. Use CH / to select hour or minute (the selected item is displayed in white), use VOL+/- to set the current time (Subject to Change). Current time 0:40 28

29 CCD setting CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings Off Transparent To enter into CCD and Vchip SETTINGS menu 1. Press MENU button repeatedly to display CCD and Vchip SETTINGS menu. 2. Press CH or CH button to select item. 3. Press VOL+ or VOL- button to confirm or adjust selected item. Closed captions From the CCD and Vchip SETTINGS menu, press CH / to select CCD Mode setting item. Press VOL- or VOL+ button to cycle between Captions 1, Captions 2, Text 1, Text 2, XDS (extended data services), Captions 3, Captions 4, Text 3, Text 4 and normal TV. Closed Captioning will display text on the screen for the hearing impaired. Note: Not all channels broadcast Closed Captions CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings Off Transparent CCD background You can select background for CCD display. From the CCD and Vchip SETTINGS menu, press CH / to select CCD Background item. Press VOL- or VOL+ button to select transparent or black. CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings Off Transparent * To exit the menu, press ENTER button. 29

30 V-chip setting V-Chip enables parents to prevent their children from watching inappropriate material on TV. V-Chip reads the ratings for programming (except for news, sports, unedited movies on premium cable and Emergency System signals ), then denies access to programming if the program's rating meets the limitations you select. In this case, the program will be blocked. * To exit the menu, press ENTER button. To enter into RATING SETTING menu 1. Press MENU button repeatedly to display CCD and Vchip SETTINGS menu. 2. Press CH or CH button to select Video Rating Settings. 3. Input a 4-digit password to enter RATING SETTING menu (the preset password is 1234 and you should change it). MOVIE RATING setup 1. Enter into RATING SETTING menu. 2. Press CH or CH button to select MPAA Rating Sys Press VOL + or VOL- button to enter into MOVIE RATING sub-menu. 4. Press CH or CH button to select the desired rating. 5. Press VOL + or VOL- button to either block the rating ("B" will appear) or unblock ("A" will appear). Movie Ratings: * G and Above (general audience) * PG and Above (parental guidance suggested) * PG-13 and Above (13 years and up) * R and Above (restricted) * NC-17 and Above (18 years and up) * X (adult) CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings Off Transparent RATING SETTING MPAA Rating Sys... TV Block Settings... Change Password... <LEFT> or <RIGHT> change, <Menu> return MOVIE RATING Rating MPAA G MPAA PG MPAA PG-13 MPAA R MPAA NC-17 MPAA X <UP/DOWN>move, <LEFT/RIGHT>change If you set PG-13, G and PG movies will be available, and PG-13, R, NC-17 and X will be blocked. Input the password to enter Press VOL+/- to enter A/B A A A A A A 30

31 V-chip setting TV RATING setup TV Parental Guidelines may have one or more letters added to the basic rating to let parents know when a show contains higher levels of violence, sex, adult 1. Enter into RATING SETTING menu. 2. Press CH or CH button to select TV Block Settings item. 3. Press VOL + or VOL- button to enter into TV RATING sub-menu. 4. Press VOL+ or VOL- button to select the desired rating. 5. Press CH or CH button to either block the rating ("B" will appear) or unblock ("A" will appear). * Y and Above (all children) (individual content categories do not apply) * Y7 (7 years and up) * G and above (general audience) (individual categories do not apply) * PG and Above (parental guidance suggested) * 14 and above (14 years and up) CCD and Vchip SETTINGS CCD Mode setting CCD Background Video Rating Settings RATING SETTING MPAA Rating Sys... TV Block Settings... Change Password... <LEFT> or <RIGHT> change, <Menu> return TV RATING Rating A/B FV V S L D TV-Y A TV-Y7 B TV-G B TV-PG B A A A A TV-14 B A A A A TV-MA B A A A <LEFT/RIGHT>move, <UP/DOWN>change, <Menu>return You can also block the criteria for each level for FV, V, S, L, D. * FV: fantasy violence (applies only to TV-Y7) * V: violence (applies to TV-PG and above, TV- 14 and Above, TV-MA) * S: sexual situations (applies to TV-PG and above, TV-14 and Above, TV-MA) * L: adult language (applies to TV-PG and above, TV-14 and Above, TV-MA) * D: sexual dialogue (applies to TV-PG and Above, TV-14) Off Transparent Input the password to enter Press VOL+/- to enter * To exit the menu, press ENTER button. Changing the password 1. Enter into RATING SETTING menu. 2. Press CH or CH button to select Change Password item. 3. Press VOL + or VOL- button to enter into the sub-menu. CHANGE PASSWORD New Password: New Password Validate: <LEFT/RIGHT> move, <Menu> return, <Enter> execute 4. Enter a new 4-digit password and validate again. Then highlight OK and press ENTER. The password has been modified successfully. Ok Cancel If you have failure in inputting the password, you can move the cursor to highlight Cancel and press ENTER button to cancel it. 31

32 Adjustment in YPbPr mode YPbPr To enter into YPbPr mode Repeatedly press button on the remote control or SOURCE button on the set's panel until the screen display YPbPr, which indicates that the set is in YPbPr mode. Connect the YPbPr terminals to Set Top Box and make sure there is signal input. Adjusting picture In YPbPr mode when there is correct input signal, press MENU button and PICTURE SETTING menu appears. Use CH / to select item and VOL+/- to adjust. Item VOL- VOL+ Brightness darker lighter Contrast weaker stronger Saturation paler deeper Sharpness softer sharper Brightness Contrast Saturation Sharpness Color Temp PICTURE SETTING 9300K Adjusting Color temperature You can select different Color temperature to obtain correct white. Press MENU button, use CH / to select Color Temp item, press the VOL+/- to select between 9300K, 7300K, 6500K. Brightness Contrast Saturation Sharpness Color Temp PICTURE SETTING 9300K * To exit the menu, press ENTER button. Adjusting horizontal / vertical position Press MENU button twice and the PICTURE POSITION menu appears. Use CH / to select item and VOL+/- to adjust. When nonstandard signal input to the set and the picture may not be in the screen center. Now you can adjust its horizontal and vertical position to display correctly. Note: The unit will try and AUTOADJUST the image each time it powers up. You may have to Reset Horizontal/Vertical after every power up for non-standard signals. Horizontal Vertical PICTURE POSITION 32

33 Adjustment in PC mode PC To enter into PC mode Repeatedly press button on the remote control or SOURCE button on the set's panel until the screen display PC, which indicates that the set is in PC mode. PC signal format Please connect VGA input and be sure that there is VGA input signal. The signal format should be one of the follows: 640 X - 75Hz 800 X - 75Hz 1024 X - 75Hz 1280 X 60Hz - 75Hz We recommend you to use (4:3) or 1280X768@60Hz (16:9) so that the set can obtain the best picture. Use AUTO. ADJ button When PC signal format changes or when you switch to PC mode by button, the set corrects picture automatically including frequency and phase to obtain the best display. During the process of auto correction, all buttons on the remote control and set's panel do not work until this process is finished. When the set displays some signal formats that are nonstandard and can not adjust by itself to the best displaying status, now you can press AUTO.ADJ button to correct the displaying again. 33

34 Adjustment in PC mode (continued) Brightness Contrast Phase Frequency Color Temp PICTURE SETTING 9300K When there is correct input signal, press MENU button and PICTURE SETTING menu appears. Use CH / to select item and VOL+/- to adjust. Adjusting brightness and contrast You can adjust brightness and contrast in PC mode and this adjustment does not affect the brightness and contrast in TV and AV mode. Adjusting phase and frequency If you can not obtain the best display after auto correction, you can adjust phase and frequency to obtain the best display. Brightness Contrast Phase Frequency Color Temp PICTURE SETTING 9300K Adjusting Color temperature You can select different Color temperature to obtain correct white. Press MENU button, use CH / to select Color Temp item, press the VOL+/- to select between Brightness Contrast Phase Frequency Color Temp PICTURE SETTING 9300K * To exit the menu, press ENTER button. 34

35 35

36 36

37 37

38 38

39 39

40 40

41 Specifications Display Features Features Display type TFT-LCD High Definition Ready (HDTV) Screen Size 30" (29.53 Diagonally) High Contrast Ratio Aspect Ratio 15:9 High Brightness (cd/m2) Resolution (native) 1280 x 768 Excellent Viewing angle Brightness * 450cd/m2 Digital Comb Filter Contrast ratio * 500 Hi-Resolution Component, S-video, Composite, RF, VGA Viewing Angle 85/85/85/85 Parental Control with V-Chip Dot Pitch (H) x 0.50(V) mm Closed Captions (CC) Maximum Color 16.7M Sleep (Power/OFF) Response time (Tr, Tf) Tr=15ms,Tf=10ms Model Specific Remote Response time (Gray/Gray) 16.6ms Unique desktop Stand with Tilt Backlight life*** 50000hrs Wall Mounting kit (included) Electronics Built-in NTSC TV tuner Digital Comb Filter / Type 4H/BULID IN 181 Channel Cable/Air Ready TV System Reception NTSC (only) Personal Computer (PC) support (VGA 15 pin D-Sub) On Screen Audio Equalizer Channel 181 Channel Cable/Air Slim-Type design, saves 70% space compared to CRT Antenna Impedance VHF-L, VHF-H, UHF 75 Ohm Super low power consumption in standby Connector type Coax F-Connector Audio Anti-glare with anti-reflective coating Hard coating (2H) Maximum Audio Output 5 watt x 2 Accessories Total number of speakers 2 FPE3000 LCD display Connections Quantity Detachable Speakers (x2) RF: TV/CATV 75ohms coaxial 1 Model specific Remote Control (Infrared) Composite Video input 1 Manual S-Video input (4pin DIN) 1 Wall mounting instructions Component input (Y,Pb,Pr) 1 (480p, 720p, 1080i**) Desktop stand (included) Component input (Y,Cb,Cr) 1 (480i only) Wall mount bracket (inc luded) VGA input15 pin D-Sub 1 Power Supply Stereo mini phone audio jack (3.5mm) 1 (for pc) Audio Video Cables L/R RCA Audio for Composite, S-Video,YCbCr input 1(shared) Power L/R RCA Audio for Component(YPbPr) input 1 Power Source V~, 47-63Hz, 4-7A Headphone:mini stereo jack 1 Unit input power 12VDC 4A, 24VDC 5A, 5VDC.5A Video Standards supported Power ON consumption <160w Composite Video input NTSC Standby consumption <2w S-Video Input NTSC Dimension (WxHxD) Component video input 480i, 480p, 720p, 1080i W/Speakers and desktop stand 36.6 x 21.7 x 9.6 inches RF NTSC W/Speakers, W/O desktop stand 36.6 x 19.0 x 3.3 inches W/O Speakers and desktop s tand 29.6 x 19.0 x 3.3 inches Power supply 8.3 x 2.1 x 4.2 inches * - measured at peak Master Carton 39.1 x 26 x 13.7 inches ** i signal downconverted to display resolution Weight (G.W.) *** - Based on brightness at 50 percent Master Carton 61.2 lbs Unit W/Stand 38.5 lbs Unit W/O Stand 31.5 lbs 41

42 42

43 PRINTED IN RECYCLED PAPER