GSM TELEPHONE SGH-G600 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
|
|
- Myra Boone
- 5 years ago
- Views:
Transcription
1 GSM TELEPHONE SGH-G600 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Part List 6. MAIN Electrical Parts List 7. Block Diagrams 8. PCB Diagrams 9. Flow Chart of Troubleshooting 10. Reference data 11. Disassembly and Assembly Instructions
2 GSPN (Global Service Partner Network) Country rth America Latin America CIS Europe China Asia Mideast & Africa Web Site service.samsungportal.com latin.samsungportal.com cis.samsungportal.com europe.samsungportal.com china.samsungportal.com asia.samsungportal.com mea.samsungportal.com This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. c Samsung Electronics Co.,Ltd Rev.1.0
3 1. Safety Precautions 1-1. Repair Precaution Repair in Shield Box, during detailed tuning. Take specially care of tuning or test, because the specification of cellular phone is sensitive for surrounding interference(rf noise). Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by the influence of magnetic force. Surely use a standard screwdriver when you disassemble this product, otherwise screw will be worn away. Use a thicken twisted wire when you measure level. therefore error of measurement is few. A thicken twisted wire has low resistance, Repair after separate Test Pack and Set because for short danger (for example an overcurrent and furious flames of parts etc) when you repair board in condition of connecting Test Pack and tuning on. Take specially care of soldering, because Land of PCB is small and weak in heat. Surely tune on/off while using AC power plug, because a repair of battery charger is dangerous when tuning ON/OFF PBA and Connector after disassembling charger. Don't use as you pleases after change other material than replacement registered on SEC System. Otherwise engineer in charge isn't charged with problem that you don't keep this rules. 1-1
4 Safety Precautions 1-2. ESD(Electrostatically Sensitive Devices) Precaution Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD (Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below. You can prevent from ESD damage by static electricity. Remove static electricity remained your body before you touch semiconductor or parts with semiconductor. There are ways that you touch an earthed place or wear static electricity prevention string on wrist. Use earthed soldering steel when you connect or disconnect ESD. Use soldering removing tool to break static electricity., otherwise ESD will be damaged by static electricity. Don't unpack until you set up ESD on product. Because most of ESD are packed by box and aluminum plate to have conductive power,they are prevented from static electricity. You must maintain electric contact between ESD and place due to be set up until ESD is connected completely to the proper place or a circuit board. 1-2
5 2. Specification 2-1. GSM General Specification GSM850 Phase 1 GSM900 Phase 1 EGSM 900 Phase 2 DCS1800 PCS1900 Freq. Band[MHz] Uplink/Downlink 824~ ~ ~ ~ ~ ~ ~ ~ ~ ~1990 ARFCN range 128~251 1~124 0~124 & 975~ ~ ~810 Tx/Rx spacing 45MHz 45MHz 45MHz 95MHz 80MHz Mod. Bit rate/ Bit Period kbps 3.692us kbps 3.692us kbps 3.692us kbps 3.692us kbps 3.692us Time Slot Period/Frame Period 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms Modulation 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK MS Power 33dBm~5dBm 33dBm~5dBm 33dBm~5dBm 30dBm~0dBm 30dBm~0dBm Power Class 5pcl ~ 19pcl 5pcl ~ 19pcl 5pcl ~ 19pcl 0pcl ~ 15pcl 0pcl ~ 15pcl Sensitivity -102dBm -102dBm -102dBm -100dBm -100dBm TDMA Mux Cell Radius 35Km 35Km 35Km 2Km - 2-1
6 Specification 2-2. GSM TX power class TX Power control level GSM850 GSM900 TX Power control level DCS1800 PCS ±2 dbm 33±2 dbm 0 30±3 dbm 30±3 dbm 6 31±2 dbm 31±2 dbm 1 28±3 dbm 28±3 dbm 7 29±2 dbm 29±2 dbm 2 26±3 dbm 26±3 dbm 8 27±2 dbm 27±2 dbm 3 24±3 dbm 24±3 dbm 9 25±2 dbm 25±2 dbm 10 23±2 dbm 23±2 dbm 11 21±2 dbm 21±2 dbm 12 19±2 dbm 19±2 dbm 4 22±3 dbm 22±3 dbm 5 20±3 dbm 20±3 dbm 6 18±3 dbm 18±3 dbm 7 16±3 dbm 16±3 dbm 8 14±3 dbm 14±3 dbm 13 17±2 dbm 17±2 dbm 14 15±2 dbm 15±2 dbm 15 13±2 dbm 13±2 dbm 16 11±3 dbm 11±3 dbm 9 12±4 dbm 12±4 dbm 10 10±4 dbm 10±4 dbm 11 8±4dBm 8±4dBm 12 6±4 dbm 6±4 dbm 17 9±3dBm 9±3dBm 13 4±4 dbm 4±4 dbm 18 7±3 dbm 7±3 dbm 14 2±5 dbm 2±5 dbm 19 5±3 dbm 5±3 dbm 15 0±5 dbm 0±5 dbm 2-2
7 3. Product Function Main Function DC-Jack TA (700mA) MMS (Multimedia Message Service) J2ME JAVA (MIDP 2.0/CLDC 1.1) EMS (Enhanced Message Service) 64 Poly S/W MIDI Bluetooth 2.0 EDR FM Radio Support USB v1.2 High Speed Support MicroSD Card Support Active backlight control Quad band(850/900/1800/1900mhz) GPRS Class
8 Product Function 3-2
9 4. Array course control 4-1. Software Adjustments 1. JIG Box(GH A): Download, Trace, Calibration, etc 2. RF test cable(gh a): RF test 3. Test cable(gh a): JIG to phone 4. Serial cable: PC to JIG 4-1
10 Array course control 4-2. Software Downloading Downloading Binary Files 2 binary files for downloading G600 G600.cla G600.tfs Pre-requsite for Downloading Downloader Program SGH-G600 Mobile Phone JIGBOX Download JIG Test Cable Serial Cable Binary files S/W Downloader Program 1. Load the binary download program by executing 4-2
11 Array course control 2. Select the Port, Baud Rate and Mode. 3. Select the binary files what you want to download 4-3
12 Array course control 4. Press the "Start" button and connect the Handset 5. When downloading is complete, automatically the small window was showed up.. 4-4
13 Array course control 4-5
14 5. Exploded View and Parts List 5-1. Cellular phone Exploded View QFR04 QFR01 QCK01 QVO01 QFU01 QMW01 QCR57 QKP01 QMI03 QMI01 QME01 QBR03 QKP02 QCA01 QLC01 QME03 QVK01 QME02 QMP01 QAN02 QSH01 QSP01 QMI04 QSD01 QPC01 QRE01 QCR05 QIF01 QFL01 QCR05 QSC05 QRF01 QSC13 QBA01 QBA00 5-1
15 Exploded View and Parts List 5-2. Cellular phone Parts list Design LOC Description SEC CODE QAN02 INTENNA-SGHG600 GH A QBA00 PMO COVER-BATTERY GH B QBA01 INNER BATTERY PACK-880MAH, BL GH A QBR03 ASSY BRACKET-KEY GH A QCA01 CAMERA MODULE-5M GH A QCK01 PMO KEY-CAMERA GH B QCR05 SCREW-MACHINE QCR05 SCREW-MACHINE QCR57 SCREW-MACHINE QFL01 ASSY CASE-SLIDE LOWER GH B QKP01 ASSY KEYPAD-MAIN(EU/E_BLK) GH B QKP02 ASSY KEYPAD-SUB(EU/E_BLK) GH B QLC01 MEA-LCD MODULE KIT GH A QME02 KEY FPCB-SUB KEY FPCB 10KEY GH A QME03 ASSY ETC-FLASH FPCB GH A QMP01 PBA MAIN-SGHG600 GH A QPC01 MEA-FPCBKIT GH A QRF01 PMO COVER-RF GH B QSC05 RMO RUBBER-LOWER SCREW CAP GH B QSC13 RMO RUBBER-REAR SCREW CAP GH B QSH01 ICT COVER-SHIELD CAN GH A QSP01 UNIT-SGHG600,SPK MODULE GH A QVK01 KEY FPCB-VOLUME KEY GH A QVO01 PMO KEY-VOLUME GH B QME01 KEY FPCB-MAIN KEY FPCB 12 KEY GH A QMI01 AS-MIC SVC GH A QMI03 AS-SGHG600 MIC RUBBER GH A QFU01 ASSY CASE-SLIDE UPPER GH B QMW01 ASSY COVER-MAIN WINDOW GH B QFR01 ASSY CASE-FRONT GH B QFR04 ASSY DECO-FRONT GH B QRE01 ASSY CASE-REAR GH B QIF01 PMO COVER-IF GH B QMI04 RMO RUBBER-PMIC GH A QSD01 PMO COVER-SD GH B 5-2
16 Exploded View and Parts List Description SEC CODE IC-MEMORY CARD CONNECTOR-ADAPTOR BAG PE BAG ZIPPER SCREW-MACHINE MICROPHONE-ASSY-WEP210 GH A CBF INTERFACE-MIC CABLE(S20P,B GH A CBF INTERFACE-DLC APCBS10BBE(S GH A BATTERY-70MAH CORE PACK GH A ADAPTOR-ATADS10UBE,BLK,UK GH A S/W CD-SGH-G600 SAMSUNG PC STU GH A KEY FPCB-SIDE KEY GH A EARPHONE-EARPHONE,3 PLUG,BLK,E GH A ASSY ETC-CONVERSION PLUG GH A LABEL(P)-UNIT SEAL GH B LABEL(P)-IMEI GH D MANUAL-SFC LEAFLET GH A LABEL(R)-WATER SOAK GH A MANUAL USERS-EU ENGLISH GH A LABEL(R)-MAIN(EU) GH A MANUAL USERS-EU ENGLISH GH A BOX-UNIT(UK) GH G CUSHION-CASE(UK) GH A PMO DECO-UPPER TOP GH C PMO COVER-DC JACK GH C PMO-VOL KEY V2 GH A PMO CASE-EARPIECE GH C RMO-EAR RUBBER 1 GH A RMO-EAR RUBBER 4 GH A RMO-RUBBER MIC GH A RMO-RUBBER SCREW GH A RMO RUBBER-CHIP GH A MPR-CONN REMOVLA TAPE GH A MPR-TAPE MAIN KEY SOLDERING GH A MPR-INSU TAPE TOUCH CONN GH A MPR-SPONGE BATT GH A MPR-SPONGE MIC GH A TAPE-SPK CONN GH A TAPE-SLIDE CONN 2 GH A TAPE ELEC GH A TAPE ELEC GH A TAPE INSU-SUB FPCB GH A TAPE INSU GH A TAPE-ABSORBER CHIP GH A VINYL-BOHO WINDOW MAIN END GH A SPONGE GH A TAPE ELEC GH A PBA MAIN-IN HOUSE GH A ELA UNIT-WEP210, EBONY GRAY(EU GH A ASSY CASE-UPPER GH D ASSY CASE-LOWER GH C 5-3
17 Exploded View and Parts List 5-4
18 6. Electrical Parts List Design LOC Description SEC CODE STATUS ANT101 ANTENNA-CHIP SA ANT102 ANTENNA-CHIP SA BAT400 BATTERY-LI(2ND) SA BTC600 HEADER-BATTERY SA C100 C-CER,CHIP SA C101 C-CER,CHIP SA C101 C-CER,CHIP SA C102 C-CER,CHIP SA C102 C-CER,CHIP SA C103 C-CER,CHIP SA C103 C-CER,CHIP SA C104 C-CER,CHIP SA C104 C-CER,CHIP SA C105 C-CER,CHIP SA C105 C-CER,CHIP SA C106 C-CER,CHIP SA C106 C-CER,CHIP SA C107 C-CER,CHIP SA C107 C-CER,CHIP SA C108 C-CER,CHIP SA C108 C-CER,CHIP SA C109 C-CER,CHIP SA C109 C-CER,CHIP SA C110 C-CER,CHIP SA C110 C-CER,CHIP SA C111 C-CER,CHIP SA C111 C-CER,CHIP SA C112 C-CER,CHIP SA C112 C-CER,CHIP SA C113 C-TA,CHIP SA C114 C-CER,CHIP SA C114 C-CER,CHIP SA C115 C-CER,CHIP SA C116 C-CER,CHIP SA C117 C-CER,CHIP SA C117 C-CER,CHIP SA C118 C-CER,CHIP SA C119 C-CER,CHIP SA C119 C-CER,CHIP SNA C120 C-CER,CHIP SA C120 C-CER,CHIP SA C121 C-CER,CHIP SA C122 C-CER,CHIP SA C123 C-CER,CHIP SA C123 C-CER,CHIP SA C124 C-CER,CHIP SA C125 C-CER,CHIP SA C126 C-CER,CHIP SA C127 C-CER,CHIP SA C128 C-CER,CHIP SA C129 C-CER,CHIP SA C130 C-CER,CHIP SA C131 C-CER,CHIP SA C132 C-CER,CHIP SA C133 C-CER,CHIP SA C134 C-CER,CHIP SA 6-1
19 Electrical Parts List Design LOC Description SEC CODE STATUS C135 C-CER,CHIP SA C136 C-CER,CHIP SA C137 C-CER,CHIP SA C138 C-CER,CHIP SA C139 C-CER,CHIP SA C140 C-CER,CHIP SA C200 C-CER,CHIP SA C201 C-CER,CHIP SA C202 C-CER,CHIP SA C203 C-CER,CHIP SA C204 C-CER,CHIP SA C205 C-CER,CHIP SA C206 C-CER,CHIP SA C207 C-CER,CHIP SA C208 C-CER,CHIP SA C209 C-CER,CHIP SA C210 C-CER,CHIP SA C211 C-CER,CHIP SA C212 C-CER,CHIP SA C213 C-CER,CHIP SA C214 C-CER,CHIP SA C215 C-CER,CHIP SA C216 C-CER,CHIP SA C217 C-CER,CHIP SA C218 C-CER,CHIP SA C219 C-CER,CHIP SA C220 C-CER,CHIP SA C300 C-CER,CHIP SA C301 C-CER,CHIP SA C302 C-CER,CHIP SA C303 C-CER,CHIP SA C304 C-CER,CHIP SA C305 C-CER,CHIP SA C306 C-CER,CHIP SA C307 C-CER,CHIP SA C308 C-CER,CHIP SA C309 C-CER,CHIP SA C310 C-CER,CHIP SA C312 C-CER,CHIP SA C313 C-CER,CHIP SA C314 C-CER,CHIP SA C315 C-CER,CHIP SA C316 C-CER,CHIP SA C317 C-CER,CHIP SA C318 C-CER,CHIP SA C319 C-CER,CHIP SA C320 C-CER,CHIP SA C321 C-CER,CHIP SA C322 C-CER,CHIP SA C323 C-CER,CHIP SA C324 C-CER,CHIP SA C325 C-CER,CHIP SA C326 C-CER,CHIP SA C327 C-CER,CHIP SA C400 C-CER,CHIP SA C401 C-CER,CHIP SA 6-2
20 Electrical Parts List Design LOC Description SEC CODE STATUS C402 C-CER,CHIP SA C403 C-CER,CHIP SA C404 C-CER,CHIP SA C405 C-CER,CHIP SA C406 C-CER,CHIP SA C407 C-CER,CHIP SA C408 C-CER,CHIP SA C409 C-CER,CHIP SA C410 C-CER,CHIP SA C411 C-CER,CHIP SA C412 C-CER,CHIP SA C413 C-CER,CHIP SA C414 C-CER,CHIP SA C418 C-CER,CHIP SA C419 C-CER,CHIP SA C420 C-CER,CHIP SA C421 C-CER,CHIP SA C422 C-CER,CHIP SA C423 C-CER,CHIP SA C424 C-CER,CHIP SA C425 C-CER,CHIP SA C426 C-CER,CHIP SA C427 C-CER,CHIP SA C501 C-CER,CHIP SA C502 C-CER,CHIP SA C504 C-CER,CHIP SA C505 C-CER,CHIP SA C506 C-CER,CHIP SA C507 C-CER,CHIP SA C508 C-CER,CHIP SA C509 C-CER,CHIP SA C510 C-CER,CHIP SA C511 C-CER,CHIP SA C512 C-CER,CHIP SA C514 C-CER,CHIP SA C515 C-CER,CHIP SA C516 C-CER,CHIP SA C517 C-CER,CHIP SA C519 C-CER,CHIP SA C520 C-CER,CHIP SA C521 C-CER,CHIP SA C523 C-CER,CHIP SA C524 C-CER,CHIP SA C525 C-CER,CHIP SA C526 C-CER,CHIP SA C527 C-CER,CHIP SA C600 C-CER,CHIP SA C601 C-CER,CHIP SA C602 C-CER,CHIP SA C603 C-CER,CHIP SA C604 C-CER,CHIP SA C605 C-CER,CHIP SA C609 C-CER,CHIP SA C610 C-CER,CHIP SA C612 C-CER,CHIP SA C614 C-CER,CHIP SA 6-3
21 Electrical Parts List Design LOC Description SEC CODE STATUS C615 C-CER,CHIP SA C617 C-CER,CHIP SA C618 C-CER,CHIP SA C619 C-CER,CHIP SA C620 C-CER,CHIP SA C702 C-CER,CHIP SA C704 C-CER,CHIP SA C705 C-CER,CHIP SA C706 C-CER,CHIP SA C707 C-CER,CHIP SA C708 C-CER,CHIP SA C709 C-CER,CHIP SA C710 C-CER,CHIP SA C711 C-CER,CHIP SA C712 C-CER,CHIP SA C713 C-CER,CHIP SA C714 C-CER,CHIP SA C715 C-CER,CHIP SA C717 C-CER,CHIP SA C718 C-CER,CHIP SA C719 C-CER,CHIP SA C720 C-CER,CHIP SA C721 C-CER,CHIP SA C722 C-CER,CHIP SA C723 C-CER,CHIP SA C724 C-CER,CHIP SA C725 C-CER,CHIP SA C726 C-CER,CHIP SA C728 C-CER,CHIP SA C729 C-CER,CHIP SA C730 C-CER,CHIP SA C731 C-CER,CHIP SA C732 C-CER,CHIP SA CD700 CONNECTOR-CARD EDGE SA CN100 CONNECTOR-COAXIAL SA CON101 JACK-DC POWER SA D101 DIODE-ZENER SA D600 DIODE-TVS SA D601 DIODE-TVS SA D602 DIODE-TVS SA D603 DIODE-TVS SA D604 DIODE-TVS SA D605 DIODE-TVS SA D700 DIODE-TVS SA D701 DIODE-TVS SA D702 DIODE-TVS SA D703 DIODE-TVS SA D704 DIODE-TVS SA D705 DIODE-TVS SA F100 DUPLEXER-FEM SA F101 FILTER-LC SA F101 FILTER-LC SA F600 FILTER-EMI SMD SA HDC700 HEADER-BOARD TO BOARD SA HDC701 HEADER-BOARD TO BOARD SA IFC600 SOCKET-INTERFACE SA 6-4
22 Electrical Parts List Design LOC Description SEC CODE STATUS L100 ICT-ON-BOARD CLIP GH A SA L101 INDUCTOR-SMD SNA L101 ICT-ON-BOARD CLIP GH A SA L102 INDUCTOR-SMD SA L102 ICT-ON-BOARD CLIP GH A SA L103 INDUCTOR-SMD SNA L103 ICT-ON-BOARD CLIP GH A SA L104 INDUCTOR-SMD SNA L104 ICT-ON-BOARD CLIP GH A SA L105 ICT-ON-BOARD CLIP GH A SA L106 INDUCTOR-SMD SA L107 INDUCTOR-SMD SA L108 INDUCTOR-SMD SA L110 INDUCTOR-SMD SA L111 INDUCTOR-SMD SA L112 INDUCTOR-SMD SA L113 INDUCTOR-SMD SA L115 BEAD-SMD SA L116 BEAD-SMD SA L117 INDUCTOR-SMD SA L300 INDUCTOR-SMD SA L301 INDUCTOR-SMD SNA L401 INDUCTOR-SMD SA L500 BEAD-SMD SA L501 BEAD-SMD SA L503 BEAD-SMD SA L505 BEAD-SMD SA L506 BEAD-SMD SA L601 BEAD-SMD SA L602 BEAD-SMD SA L603 BEAD-SMD SA L605 INDUCTOR-SMD SA L606 INDUCTOR-SMD SA OSC100 CRYSTAL-SMD SA OSC101 CRYSTAL-SMD SA OSC300 CRYSTAL-SMD SA OSC400 CRYSTAL-SMD SA PAM500 IC-AUDIO AMP SA PM400 IC-POWER SUPERVISOR SA Q100 FET-SILICON SA QCR05 SCREW-MACHINE SA QCR05 SCREW-MACHINE SA QCR05 SCREW-MACHINE SA QCR57 SCREW-MACHINE SA R100 R-CHIP SA R101 R-CHIP SA R101 R-CHIP SA R102 R-CHIP SA R102 R-CHIP SA R103 R-CHIP SA R104 R-CHIP SA R104 R-CHIP SA R105 R-CHIP SA R105 R-CHIP SA R106 R-CHIP SA R106 R-CHIP SA 6-5
23 Electrical Parts List Design LOC Description SEC CODE STATUS R107 R-CHIP SA R108 R-CHIP SA R109 R-CHIP SA R110 R-CHIP SA R111 R-CHIP SA R112 R-CHIP SA R113 R-CHIP SA R115 R-CHIP SA R116 R-CHIP SA R117 R-CHIP SA R118 R-CHIP SA R119 R-CHIP SA R120 R-CHIP SA R121 R-CHIP SA R122 R-CHIP SA R123 R-CHIP SA R203 R-CHIP SA R204 R-CHIP SA R205 R-CHIP SA R206 R-CHIP SA R207 R-CHIP SA R208 R-CHIP SA R209 R-CHIP SA R210 R-CHIP SA R211 R-CHIP SA R212 R-CHIP SA R305 R-CHIP SA R307 R-CHIP SA R308 R-CHIP SA R311 R-CHIP SA R313 R-CHIP SA R316 R-CHIP SA R317 R-CHIP SA R318 R-CHIP SA R319 R-CHIP SA R322 R-CHIP SA R323 R-CHIP SA R324 R-CHIP SA R325 R-CHIP SA R326 R-CHIP SA R400 R-CHIP SA R402 R-CHIP SA R403 BEAD-SMD SA R408 R-CHIP SA R410 R-CHIP SA R411 R-CHIP SA R412 R-CHIP SA R413 R-CHIP SA R414 R-CHIP SA R415 R-CHIP SA R416 R-CHIP SA R417 R-CHIP SA R501 R-CHIP SA R502 R-CHIP SA R503 R-CHIP SA R504 R-CHIP SA 6-6
24 Electrical Parts List Design LOC Description SEC CODE STATUS R507 R-CHIP SA R508 R-CHIP SA R509 R-CHIP SA R510 R-CHIP SA R511 R-CHIP SA R512 R-CHIP SA R513 R-CHIP SA R514 R-CHIP SA R515 R-CHIP SA R600 R-CHIP SA R601 R-CHIP SA R602 R-CHIP SNA R603 R-CHIP SA R604 R-CHIP SA R606 R-CHIP SA R607 R-CHIP SA R608 R-CHIP SA R609 R-CHIP SA R610 R-CHIP SA R611 BEAD-SMD SA R612 R-CHIP SA R700 R-CHIP SNA R701 R-CHIP SA R703 R-CHIP SA R704 R-CHIP SA R705 R-CHIP SA R706 R-CHIP SA R707 R-CHIP SA R708 R-CHIP SA R709 R-CHIP SA R712 R-CHIP SA R713 R-CHIP SA SIM400 CONNECTOR-CARD EDGE SA TA101 C-TA,CHIP SA TA300 C-TA,CHIP SA TA400 C-TA,CHIP SA TA401 C-TA,CHIP SA TA500 C-TA,CHIP SA TA501 C-TA,CHIP SA TA502 C-TA,CHIP SA TA503 C-TA,CHIP SA TA504 C-TA,CHIP SA TA505 C-TA,CHIP SA TA506 C-TA,CHIP SA TA507 C-TA,CHIP SA TA600 C-TA,CHIP SA TA601 C-TA,CHIP SA U100 IC-POWER AMP SA U101 IC-POSI.FIXED REG SA U101 IC-DATA COMM./GEN SA U102 IC-TRANSCEIVER SA U103 IC-CMOS LOGIC SA U104 IC-TRANSCEIVER SA U300 IC-POSI.FIXED REG SA U301 IC-DC/DC CONVERTER SA U302 IC-ANALOG MULTIPLEX SA 6-7
25 Electrical Parts List Design LOC Description SEC CODE STATUS U401 IC-POSI.FIXED REG SA U402 IC-POSI.FIXED REG SA U500 IC-POSI.FIXED REG SA U501 IC-ANALOG MULTIPLEX SA U503 IC-ANALOG MULTIPLEX SA U504 IC-ANALOG MULTIPLEX SA U600 IC-ANALOG SWITCH SA U601 IC-DEMODULATOR SA U700 IC-POSI.FIXED REG SA UCD300 IC ASIC-SGHG600 GH A SA UCD500 IC-CODEC SA UCP200 IC-COMM. CONTROLLER SA UME200 IC-MCP SA UPL200 IC-CMOS LOGIC SA UPL700 FET-SILICON SA V601 VARISTOR SA VR101 VARISTOR SA VR102 VARISTOR SA VR103 VARISTOR SA VR104 VARISTOR SA VR105 VARISTOR SA VR106 VARISTOR SA VR107 VARISTOR SA VR110 VARISTOR SA VR600 THERMISTOR-NTC SA ZD101 DIODE-SCHOTTKY SA ZD600 DIODE-ZENER SA ZD601 DIODE-TVS SA ZD602 DIODE-TVS SA ZD603 DIODE-TVS SA ZD604 DIODE-TVS SA ZD605 DIODE-TVS SA 6-8
26 7. Block Diagrams 7-1. RF Solution Block Diagram 7-1
27 Block Diagrams 7-2. BT Solution Block Diagram 7-2
28 Block Diagrams 7-3. Base Band Solution Block Diagram MIC RECEIVER BB INTERFACE Serial Data Interface Battery Type Battery Voltage SPEAKER I/O Interface Battery Temperature VIBRATOR Ext. SPEAKER PCF5213EL1 A/D Interface D1VDD D2VDD MELODY IC (64 Poly) RF INTERFACE D3VDD SYSTEM CLOCK (26MHz) AFC AVDD VINT MV319DNQ RAMP IOVDD VDD_RX_TX 1G OneNAND MEMORY VCC_SYN MIC_BIAS KEY_BOARD Li-Ion Battery (Slim,Standard) PMU CPVDD SIMEN GPO LCD Charging Circuit RTC_CLOCK (32.768KHz) SIM CARD VCHG VSAVE 7-3
29 8. PCB Diagrams Top 8-1
30 PCB Diagrams Bottom 8-2
31 9. Flow Chart of Troubleshooting 9-1. Power On ' Power On ' does not work Check the Battery Voltage is more than 3.7V Change the Battery C418(VISA) = 2.6V? Check the PMU related to VISA Check the Clock at R409=32KHZ Resolder OSC400 C400(+VDD_IO_LOW) & C402(+VDD_IO_HIGH) = "H"? Check the related circuit C425(+VDD_GSM_CORE) =1.2V? Check the +VDD_GSM_CORE circuit Check the initial operation END 9-1
32 Flow Chart of Troubleshooting 9-2
33 Flow Chart of Troubleshooting 9-2. Initial Initial Failure UCP200 pin C11 (RSTON) ="H"? Check the circuit related to reset UCP200 pin F1(RSTEXTn) ="H"? OK? change UCP200 Check the 16bit data signal &memoryce END 9-3
34 Flow Chart of Troubleshooting 9-4
35 Flow Chart of Troubleshooting 9-3. Charging Part Abnormal charging part Check the PM400 pin 38 >5.0V Check the circuit related to V_EXT_CHARGE PM400 pin 34(AUX_ON) ="L"? Check the circuit related to AUX_ON signal Check the PM400 pin V Resolder or replace PM400 END 9-5
36 Flow Chart of Troubleshooting 9-6
37 Flow Chart of Troubleshooting 9-4. Sim Part Phone can't access SIM Card SIM400 pin 1,5 = "H"? Resolder or replace PM400 After Power ON, Check SIMCLK Signal on pin3 of SIM400 in a few second Check the Clock After SIM card insert, SIM400 pin 2 = "H(SIM_RST)"? Replace PBA Check the SIM Card END 9-7
38 Flow Chart of Troubleshooting 9-8
39 Flow Chart of Troubleshooting 9-5. Microphone Part Microphone does not work Check the connection from MIC FPCB Replace the MIC FPCB Check the circuit from UCP200 to MIC FPCB Resolder the U503, C519, C521, R509, R512 END 9-9
40 Flow Chart of Troubleshooting 9-10
41 Flow Chart of Troubleshooting 9-6. Speaker Part(Melody) Speaker does not work PAM500 pin15,17 1.8V? (When PAM500 operate) Resolder PAM500 Is Speaker working? Change the Speaker END 9-11
42 Flow Chart of Troubleshooting 9-12
43 Flow Chart of Troubleshooting 9-7. Key Data Input Check Initial Operation When one of the keys is pushed, Check the Dome sheet & Key Pad is it displayed on LCD? When one of the keys is pushed, Replace the Key PBA KBIO signal is OK? END 9-13
44 Flow Chart of Troubleshooting 9-8. Back Light (for Color Main LCD) Backlight does not work Is LCD Contrast set on high level in the Menu? Set LCD Contrast on high level Check the Slide FPCB Change the Slide FPCB or LCD END 9-14
45 Flow Chart of Troubleshooting 9-9. Key Back Light Main Key LED does not work Check the key FPCB connector on PBA Reconnect the key FPCB IS key FPCB ok? Change key FPCB END 9-15
46 Flow Chart of Troubleshooting Camera part "Camera" function does not work Check the Camera connector on PBA Reconnect the camera module Is there another problem? Replace the camera module END 9-16
47 Flow Chart of Troubleshooting Radio part Radio does not work R V Resolder R613 and Check PMU part R610, R612, C614, C V Resolder R610, R612, C614, C615 and check U601 L605 2V Check or Replace U601 C618, C619, C620, L606 is OK? (When U601 operate) Resolder C618, C619, C620, L606 Check UCP200 signal related to U601 END 9-17
48 Flow Chart of Troubleshooting 9-18
49 Flow Chart of Troubleshooting GSM Receiver RX ON Cell Power : -60dBm F100 Pin11-65dBm Resolder CN100,C102,L109 F100 3,4-68dBm Check F100 pin10,pin14 = L Check ANT Switch control circuit Resolder F100 U102 pin 24-70dBm pin 25-70dBm Resolder C104, C105, L111 U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check & Resolder C122,C126,C128 And PMU Part Resolder U102 Check UCP200 END 9-19
50 Flow Chart of Troubleshooting GSM Transmitter TX ON (5Level) F100 Pin11 30dBm Resolder CN100,C102,L109 F100 pin17 30dBm Check F100 pin14 = H (2.6V), Pin10 = L Check ANT Switch control circuit Change or Resolder F100 U100 pin12 30dBm Resolder or Change C120, C121, L114 U100 pin7-4dbm Check U100 pin 2,3,5,6,8, +Vbatt pin4ok? Resolder or Change U100 Check VBAT or PAM control signal U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check U102, C122,C126,C128 Resolder U102 Check UCP200 END 9-20
51 Flow Chart of Troubleshooting GSM850 Receiver RX ON Cell Power : -60dBm F100 Pin11-65dBm Resolder CN100,C102,L109 F100 1,2-68dBm Check F100 pin10,pin14 = L Check ANT Switch control circuit Resolder F100 U102 pin 26-70dBm pin 25-70dBm Resolder C100, C103, L110 U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check & Resolder C122,C126,C128 And PMU Part Resolder U102 Check UCP200 END 9-21
52 Flow Chart of Troubleshooting GSM850 Transmitter TX ON (5Level) F100 Pin11 30dBm Resolder CN100,C102,L109 F100 pin17 30dBm Check F100 pin14 = H (2.6V), Pin10 = L Check ANT Switch control circuit Change or Resolder F100 U100 pin12 30dBm Resolder or Change C120, C121, L114 U100 pin7-4dbm Check U100 pin 2,3,5,6,8, +Vbatt pin4ok? Resolder or Change U100 Check VBAT or PAM control signal U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check U102, C122,C126,C128 Resolder U102 Check UCP200 END 9-22
53 Flow Chart of Troubleshooting DCS Receiver RX ON Cell Power : -60dBm F100 Pin11-65dBm Resolder CN100,C102,L109 F100 5,6-68dBm Check F100 pin10,pin14 = L Check ANT Switch control circuit Resolder F100 U102 pin 22-70dBm pin 23-70dBm Resolder C106, C108, L112 U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check & Resolder C122,C126,C128 And PMU Part Resolder U102 Check UCP200 END 9-23
54 Flow Chart of Troubleshooting DCS Transmitter TX ON (5Level) F100 Pin11 25dBm Resolder CN100,C102,L109 F100 pin15 25dBm Check F100 pin14 = L (2.6V), Pin10 = H Check ANT Switch control circuit Change or Resolder F100 U100 pin18 25dBm Resolder or Change C116, C117, C118 U100 pin1-4dbm Check U100 pin 2,3,5,6,8, +Vbatt pin4ok? Resolder or Change U100 Check VBAT or PAM control signal U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check U102, C122,C126,C128 Resolder U102 Check UCP200 END 9-24
55 Flow Chart of Troubleshooting PCS Receiver RX ON Cell Power : -60dBm F100 Pin11-65dBm Resolder CN100,C102,L109 F100 7,8-68dBm Check F100 pin10,pin14 = L Check ANT Switch control circuit Resolder F100 U102 pin 20-70dBm pin 21-70dBm Resolder C113, C119, L113 U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check & Resolder C122,C126,C128 And PMU Part Resolder U102 Check UCP200 END 9-25
56 Flow Chart of Troubleshooting PCS Transmitter TX ON (5Level) F100 Pin11 25dBm Resolder CN100,C102,L109 F100 pin15 25dBm Check F100 pin14 = L (2.6V), Pin10 = H Check ANT Switch control circuit Change or Resolder F100 U100 pin18 25dBm Resolder or Change C116, C117, C118 U100 pin1-4dbm Check U100 pin 2,3,5,6,8, +Vbatt pin4ok? Resolder or Change U100 Check VBAT or PAM control signal U102 pin 4,5,6,7 0.2Vp_p U102pin 11,12,16, 29,32,33,36 2.8V pin10 1.8V Check U102, C122,C126,C128 Resolder U102 Check UCP200 END 9-26
57 Flow Chart of Troubleshooting 9-27
58 Flow Chart of Troubleshooting Bluetooth part Bluetooth does not work F500 pin 2-4dB Resolder or replace C137, L117, ANT102 C132, C133 (+position), is 1.8V Resolder C132, C133 and check the PMU part C130,C131,C135,C136 is 1.5V Resolder C130,C131,C135,C136 check or Replace U503 TP_BT_POEWR 1.8V Pin A5 1.7V(32kHz) check TP_BT_POEWR check or Replace U503 Check UCP200 END 9-28
59 Flow Chart of Troubleshooting 9-29
60 Flow Chart of Troubleshooting 9-30
61 10. Reference data Reference Abbreviate AAC: Advanced Audio Coding. AVC : Advanced Video Coding. BER : Bit Error Rate BPSK: Binary Phase Shift Keying CA : Conditional Access CDM : Code Division Multiplexing C/I : Carrier to Interference DMB : Digital Multimedia Broadcasting EN : European Standard ES : Elementary Stream ETSI: European Telecommunications Standards Institute MPEG: Moving Picture Experts Group PN : Pseudo-random ise PS : Pilot Symbol QPSK: Quadrature Phase Shift Keying RS : Reed-Solomon SI : Service Information TDM : Time Division Multiplexing TS : Transport Stream 10-1
62 Reference data 10-2
63 11. Disassembly and Assembly Instructions Disassembly Instructions 1 2 1) Unscrew 6points from the rear case 2) Open the IF COVER 1) Disjoint from low side to up side of rear case. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 3 1) Remove the volume key and camera key. 2) Disconnect the 3X4 key connecter. 1) Be careful not to make scratch and molding damage! 11-1
64 Disassembly and Assembly Instructions 4 1) Lift B'd up and Disconnect the slide FPCB connecter. 5 1) Disjoint the key bracket from front case. 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 1) Be careful not to make scratch and molding damage! 6 7 1) Slide up and Remove the keypad. 1) Unscrew 6 points from the front case. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 11-2
65 Disassembly and Assembly Instructions 8 1) Disjoint the front case as below picture. 9 1) Remove the screw rubbers. 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 1) Be careful not to make scratch and molding damage! ) Remove the tape between FPCB and lower. 1) Unscrew 4 points from the lower case. 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 1) Be careful not to make scratch and molding damage! 11-3
66 Disassembly and Assembly Instructions 12 1) After disjoint the hooker of the lower side, disassemble the LOWER case as below 13 1) Disjoint the hooker of the LCD as below the picture. the picture. 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the camera FPCB damage! 14 1) Disassemble the upper case as below the picture. 1) Be careful not to make scratch and molding damage! 11-4
67 Disassembly and Assembly Instructions Assembly Instructions 1 1) Insert the camera FPCB into connector. 2 1) Insert the slide FPCB into connector. 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the camera FPCB damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 3) Be careful make right side of FPCB. 3 1) Insert sub key FPCB into connector. 4 1) Attach tape to the slide connector. 2) Attach tape to FPCB. (Guide line) 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 11-5
68 Disassembly and Assembly Instructions 5 1) Insert the speaker module and flash kit. 6 1) Attach tape to the connector. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make the FPCB damage! 7 1) Put the Speaker and Camera to the Upper case 8 1) Joint the lower hooks. 2) Joint the LCD hooks 3) Insert the sub key into guide holes. 1) Be careful not to make scratch and molding damage! 2) Be careful not to disconnect the speaker 1) Be careful not to make scratch and molding damage! 11-6
69 Disassembly and Assembly Instructions 9 1) Screw 4 points on Lower assy'. 10 1) Fold slide FPCB together 2) Attach slide to the lower guide holes. 1) Be careful not to make scratch and molding damage! 2) TORQE (1.1 ± 0.1 Kgf Cm) 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 11 1) Insert the 2 points screw rubbers into the lower case 12 1) Insert the FPCB into front FPCB hole. 2) Inset front holes into lower hooks. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 11-7
70 Disassembly and Assembly Instructions 13 1) Screw 4 points on front ass'y. 14 1) Let a key pad on front ass'y. 1) Be careful not to make scratch and molding damage!. 2) TORQE (1.1 ± 0.1 Kgf Cm) 1) Be careful not to make scratch and molding damage! 15 1) Lock 3X4 bracket to front ass'y. 2) Let a mic rubber on mic. 16 1) Insert the slide connect to slide FPCB horizontally. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to make the FPCB damage! 11-8
71 Disassembly and Assembly Instructions 17 1) Attach the volume key FPCB and camera key FPCB to the front ass'y, right side slightly. 2) Insert 3X4 key FPCB into B'd connector 18 1) Put the volume key and camera key to the front ass'y, right side slightly. 1) Be careful not to make scratch and molding damage!. 1) Be careful not to make scratch and molding damage! 19 1) Assemble the rear case. 20 1) Screw 6 points. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) TORQE (1.1 ± 0.1 Kgf Cm). 11-9
72 Disassembly and Assembly Instructions 11-10
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE. SGH-D900i CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation. 4. Array course control
GSM TELEPHONE SGH-D900i GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions
More informationGSM TELEPHONE SGH-J700 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-J700 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. Main Electrical Parts List 7. Block Diagrams
More informationUMTS TELEPHONE SGH-L760 UMTS TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
UMTS TELEPHONE SGH-L760 UMTS TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block
More informationGSM TELEPHONE. SGH-i710 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation
GSM TELEPHONE SGH-i710 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions
More informationGSM TELEPHONE SGH-X550 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation
GSM TELEPHONE SGH-X550 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions
More informationGSM TELEPHONE SGH-T619 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-T619 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions 6. MAIN Electrical
More informationGSM TELEPHONE SGH-E380 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-E380 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationSERVICE Manual GSM TELEPHONE SGH-E Specification. 2. Flow Chart of Troubleshooting. 3. Exploded Views and Parts List. 4. Electrical Parts List
GSM TELEPHONE SGH-E310 SERVICE Manual GSM TELEPHONE CONTENTS 1. Specification 2. Flow Chart of Troubleshooting 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams
More informationSERVICE Manual GSM TELEPHONE SGH-E Specification. 2. Flow Chart of Troubleshooting. 3. Exploded Views and Parts List. 4. Electrical Parts List
GSM TELEPHONE SGH-E300 SERVICE Manual GSM TELEPHONE CONTENTS 1. Specification 2. Flow Chart of Troubleshooting 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams
More informationSGH-M Specification. 2. Exploded View and Parts list. 3. Chart of Troubleshooting. 4. Array course control. 5. Block Diagrams. 6.
GSM TELEPHONE SGH-M300 GSM TELEPHONE CONTENTS 1. Specification 2. Exploded View and Parts list 3. Chart of Troubleshooting 4. Array course control 5. Block Diagrams 6. PCB Diagrams 7. MAIN Electrical Parts
More informationGSM TELEPHONE SGH-D830 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D830 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE SGH-D Specification. 2. Circuit Description. 3. Exploded Views and Parts List. 4. Electrical Parts List. 5.
GSM TELEPHONE SGH-D820 1. Specification 2. Circuit Description 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams 7. Flow Chart of Troubleshooting This Service
More informationapple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple
More informationGSM TELEPHONE SGH-X500 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-X500 GSM TELEPHONE CONTENTS 1. Safety Precautions. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. Disassembly and Assembly instructions 7.
More informationAVE HOME FAGOR CVBS TO DVB-T ENCODER MODULATOR. Fagor Electr6nica
AVE HOME CVBS TO DVB-T ENCODER MODULATOR FAGOR Fagor Electr6nica TABLE OF CONTENTS 1. SPECIFICATIONS... 12 1.1 Product Overview... 12 1.2 Appearance and Description... 12 1.3 Diagram... 13 1.4 Characteristics...
More informationIt will cause malfunction if the monitor is operating with unspecified power supply
User Manual / Installation Guide Model No. PTM-1525R/RT Warning! It will cause malfunction if the monitor is operating with unspecified power supply unit or incorrect power voltage. Do not exposure this
More informationapple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber Apple Computer, Inc. All rights reserved.
apple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber 2004 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Studio Display 17" LCD (ADC) 2003 Apple
More informationSPECIFICATION. DVB-T / Worldwide NIM Tuner
1.Feature * DVB-T demodulator for COFDM with excellent multipath performance, meeting: * DVB-T Digital Television Standard ETS 300744 * Nordig-Unified v1.0.3 Receiver Specification 2.Applications * Digital
More informationGSM TELEPHONE SGH-P310 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-P310 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationUser Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor
Touch Display LCD Monitor User Manual Installation Guide 15 Resistive Touch LCD Monitor MODEL: KK1500-TR i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com User
More informationTV-1800C (PAL B / G,H) TV-1800D (PAL I) TV-1800I (PAL B / G) TV-1800N (PAL B / G,H)
< TUNING > (without price) TV-1800C (PAL B / G,H) TV-1800D (PAL I) TV-1800I (PAL B / G) TV-1800N (PAL B / G,H) (KX-523) DEC. 1996 R CONTENTS Page SPECIFICATIONS... 1 BLOCK DIAGRAM... 2 CIRCUIT OPERATIONS...
More informationPLL1920M LED LCD Monitor
PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6
More informationMASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz
Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO
More information8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number
Installation Note 8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit Network Analyzer Model Number 8753E 8753ET 8753ES Applicable Upgrade Kit Model Number
More informationWileyfox Service Support. Wiley Fox Swift Service Manual
Wiley Fox Swift Service Manual Contents 1. A5042 (WILEY FOX SWIFT) overview... 3 1.1 A5042 (WILEY FOX SWIFT) brief introduction... 3 1.2 Function diagram... 3 1.3 Mainboard component distribution diagram...
More informationUser Manual MODEL: KKF1500-PCAP. True FLAT P-CAP LCD Monitor. Installation Guide. 15 True FLAT P-CAP Touch LCD Monitor
True FLAT P-CAP LCD Monitor User Manual Installation Guide 15 True FLAT P-CAP Touch LCD Monitor MODEL: KKF1500-PCAP i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com
More informationFixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationTen-Tec (865) Service Department:(865)
Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram
More informationGSM TELEPHONE SGH-D807 GSM TELEPHONE. CONTENTS 1. Safety Precautions. 2. General Introduction. 3. Specification. 4.
GSM TELEPHONE SGH-D807 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. General Introduction 3. Specification 4. Product Function 5. Circuit Description 6. Test Command & Test Procedure 7. Array course
More informationP XGA TFT Monitor. User s Manual
P6151 15 XGA TFT Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements
More informationMONITOR POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2099-10xx 10MHz Frequency Source April 2014, Rev. H MENU INTERNAL LEVEL = +10dBm MONITOR POWER 1 2 MODEL 2099 FREQUENCY SOURCE CROSS TECHNOLOGIES INC. ALARM OVEN REMOTE EXECUTE
More informationV26 Chassis V26+ Chassis V26++ Chassis WD WD WD WD WD WD-62825
Digital Light Processing Projection Television V26 Chassis 2004 V26 Chassis V26+ Chassis V26++ Chassis WD-52525 WD-52725 WD-52825 WD-62525 WD-62725 WD-62825 Copyright 2004 Mitsubishi Digital Electronics,
More informationSPECIFICATION. DVB-T/ DVB-C / Worldwide hybrid Switchable NIM Tuner
1.Feature *. Integrated RF switch, NTSC VIF demodulator, COFDM demodulator *. All-in-one full NIM function with compact size, optimal solution for cost reduction and shortening product development lead-time.
More informationJinyoung Contech Co., Ltd.
TO : Jinyoung Contech Co., Ltd. #501, 222-12 MARIOTOWER, GURO-DONG, GURO-KU, SEOUL, KOREA TEL : 82-2-890-6400 FAX : 82-2-890-6406 HOME PAGE : http://www.jyct.com/ Issued Date : 2006-12-15 Page : 13ages
More informationSGH-M Specification. 2. Exploded View and Parts list. 3. Chart of Troubleshooting. 4. Array course control. 5. Block Diagrams. 6.
GSM TELEPHONE SGH-M300 GSM TELEPHONE CONTENTS 1. Specification 2. Exploded View and Parts list 3. Chart of Troubleshooting 4. Array course control 5. Block Diagrams 6. PCB Diagrams 7. MAIN Electrical Parts
More informationIC-F300/F400/S SERIES PRECAUTIONS
SCRAMBLER UNIT INSTALLATION INSTRUCTIONS UT-109/UT-110 Rev.1.2 Thank you for purchasing the UT-109/UT-110 SCRAMBLER UNIT. The UT-109 and UT-110 are designed for Icom F series VHF/UHF FM transceivers. Please
More informationINSTALLATION MANUAL FT-FOTR-1VDE-ST-S
INSTALLATION MANUAL FT-FOTR-1VDE-ST-S 1-Channel Digital Duplex Baseband Video Transmitter and Receiver With Reverse Data Transmission & Ethernet Transmission v1.0 4/5/11 1 PACKAGE CONTENTS This package
More informationReplacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly
Replacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly Introduction The Backlight Replacement Kit provides a replacement backlight for the PanelMate
More informationSquareLED - Aura Bar & Matrix Beam Light 100
SquareLED - Aura Bar & Matrix Beam Light 100 1. SAFETY INSTRUCTIONS Please read these instructions carefully they include the important information about the installation usage and maintenance of this
More informationACTIVE IF SPLITTER/COMBINER UHP-IFS
ACTIVE IF SPLITTER/COMBINER UHP-IFS GENERAL DESCRIPTION AND INSTALLATION GUIDE DOCUMENT RELEASE 2 [UHP.IFS.2.EN] JUNE 2016 CONTENT Acronyms and Abbreviations... 4 Introduction... 5 Required level of qualification...
More informationMAXCOM PRODUCT SPECIFICATIONS FIBER OPTIC VIDEO / AUDIO / ASI LINK. Model MX3257HD. Description. Features. Model Selection Guide
MAXCOM PRODUCT SPECIFICATIONS FIBER OPTIC VIDEO / AUDIO / ASI LINK Model MX3257HD Description The rack-mountable MX3257HD fiber optic video multiplexer is ideal for transmitting 1 channel of video, 2 channels
More informationUltra-ViewRF 8HD Director Monitor. User Operation Manual
Ultra-ViewRF 8HD 5.8GHz Wireless Director Monitor User Operation Manual 17.1.2013 v2_7 Video Equipment Rentals - VER 912 Ruberta Avenue Glendale, CA 91201 - U.S.A. Office 818-956-1444 Table of Contents
More informationSGH-U Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control. 5. Exploded View and Parts list
GSM TELEPHONE SGH-U800 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts list 6. MAIN Electrical Parts List 7. Disassembly
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationBuilding the BX24-AHT
Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with
More informationSATFINDER4 INTRODUCTION USER GUIDE AND CERTIFICATE OF GUARANTEE
SATFINDER4 INTRODUCTION USER GUIDE AND CERTIFICATE OF GUARANTEE CONTENTS : General Safety...... 3 Basic Properties.... 4 Front Panel Keys... 5 Back Panel Details 5 Charger Adapters.. 6 Utilization of Satfinder4......
More informationUser s Manual of Signal Level Meter TABLE OF CONTENTS
TABLE OF CONTENTS A OVERVIEW OF SIGNAL LEVEL METER...2 B FEATURES OF SIGNAL LEVEL METER...2 C PRECAUTIONS...2 D PANEL AND LCD...3 E INSTRUCTIONS OF KEYS...3 1. SINGLE-CHANNEL MEASUREMENT...4 2. SINGLE-FREQUENCY
More informationModification Information (MOD) For. Last Updated: Sep, Type:
Modification Information (MOD) For TKR-750/850 Version2 TKR-751/851 Version: 1.02 USA Last Updated: Sep, 2005 Language: English Type: K About Copyright All copyrights and other intellectual property rights
More informationINSTALLATION INSTRUCTIONS FOR. MODEL 2230LED
INSTALLATION INSTRUCTIONS FOR MODEL 2230LED www.sportablescoreboards.com 1 Table of Contents MODEL 2230LED... 3 8 X 4 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:...
More informationN3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012
N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking
More informationSingMai Electronics SM06. Advanced Composite Video Interface: HD-SDI to acvi converter module. User Manual. Revision 0.
SM06 Advanced Composite Video Interface: HD-SDI to acvi converter module User Manual Revision 0.4 1 st May 2017 Page 1 of 26 Revision History Date Revisions Version 17-07-2016 First Draft. 0.1 28-08-2016
More informationDM-1CH SD DVB-T MODULATOR INSTRUCTION MANUAL
DM-1CH SD DVB-T MODULATOR INSTRUCTION MANUAL 2. Caution Statements and Table of Contents Table of Contents 2. Caution Statements and Table of contents 3. Important Safety Instructions 4. Important Safety
More informationI R T Electronics Pty Ltd A.B.N. 35 000 832 575 26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA National: Phone: (02) 9439 3744 Fax: (02) 9439 7439 International: +61 2 9439 3744 +61 2 9439 7439 Email:
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More informationCVM-WM300. UHF Wireless Microphone USER MANUAL
CVM-WM300 UHF Wireless Microphone USER MNUL Foreword Thanks for purchasing COMIC WM300 UHF wireless microphone. WM300 is an all-metal wireless microphone with dual-transmitter triggered by one receiver,
More informationDEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide
DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide SPECIFICATIONS Noise Figure: < 0.8 db Gain: > 15 db Frequency Range: 3400-3500 MHz Input Voltage: 7-16 VDC Description: The 9ULNACK
More informationTable of Contents. 1. Safety Use. 2. General Description. 3. Connection Diagram. 4. Operations and Management. 4.1 Display Status. 4.
DTM-HD01 Thank you for buying this encoder modulator. Please read this manual carefully to install, use and maintain the encoder modulator in the best conditions of performance. Keep this manual for future
More informationGSM TELEPHONE. SGH-Z650i GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-Z650i GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts list 6. MAIN Electrical Parts List 7. Block
More informationINSTALLATION INSTRUCTIONS FOR
INSTALLATION INSTRUCTIONS FOR MODEL 2240LED www.sportablescoreboards.com 1 Table of Contents 8 X 7 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR
More informationGood Display Specifications
Specifications Type: Model No. Description: 5.0inch TFT LCD module GD567M03-GTI050TN22 5.0 LCD with 640 x RGB x 480 dots Supports CVBS/Video & VGA input RoHS Compliant Prepared: Xiaoli Lan Checked: Moon
More informationT3316 IP QAM Modulator User Manual
T3316 IP QAM Modulator User Manual SW Version: 1.02 HW version: 0.70.0.0 Web NMS version: 1.02 Intended Audience About This Manual This user manual has been written to help people who have to use, to integrate
More informationOPERATOR MANUAL OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM
PTY. LTD A.B.N. 83 003 020 504 OPERATOR MANUAL OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM Document
More informationRF4432 wireless transceiver module
RF4432 wireless transceiver module 1. Description RF4432 adopts Silicon Lab Si4432 RF chip, which is a highly integrated wireless ISM band transceiver. The features of high sensitivity (-121 dbm), +20
More informationEX04-000D. DVB-T/2xT/T2 MODULATOR DVB MODULATOR
EX04-000D DVB-T/2xT/T2 MODULATOR Key Features Capable of transmitting one DVB-T2 or two independent DVB-T signals at the same time. In full compliance with the last version of EN300744 (DVB-T) and EN302755
More informationXTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors
XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only
More informationProduct information. Front-door station series with video for surface-mount
Product information Front-door station series with video for surface-mount series VPES series VPDS 2 05/2006 Table of contents Scope of delivery...3 Safety notices...3 General notes on the cabling in TCS
More informationIPad 4 REPAIR GUIDE. Version Edition
IPad 4 REPAIR GUIDE Version 1 2016 Edition IPad 4 REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND
More informationUser Manual Wireless HD AV Transmitter & Receiver Kit
Ma User Manual Wireless HD AV Transmitter & Receiver REV.1.0 Thank you for purchasing this Wireless HD AV Transmitter & Receiver. Please read the following instructions carefully for your safety and prevention
More informationSPECIFICATION. Multistandard Demodulator tuner. ATSC/Legacy analog NTSC/BTSC
1.Feature MATSCA-SF is the Multistandard Demodulator ATSC/QAM/NTSC module which integrates product is especially suitable for PVR or PIP-TV application. - Supported modulation standards:. ATSC digital
More informationAlice EduPad Board. User s Guide Version /11/2017
Alice EduPad Board User s Guide Version 1.02 08/11/2017 1 Table OF Contents Chapter 1. Overview... 3 1.1 Welcome... 3 1.2 Launchpad features... 4 1.3 Alice EduPad hardware features... 4 Chapter 2. Software
More information2W Wireless Mobile Video Transmitter (ST6000TKMD) User Manual
2W Wireless Mobile Video Transmitter (ST6000TKMD) User Manual TENG YUANZHI SHENZHEN ELECTRONICS CO.,LTD. 2010.10.23 1 Features Low system latency COFDM modulation, Stable transmission MPEG-2 video compression,
More informationIPad 3 (glass) REPAIR GUIDE. Version Edition
IPad 3 (glass) REPAIR GUIDE Version 1 2016 Edition IPad 4 REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,
More informationReplacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Backlight Assembly
Introduction Replacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Assembly Instruction Leaflet IL04802009E Effective September 2008
More informationRF Detector with Real Time remote Monitoring Capability Protect from RF Audio/Video Transmitters and Laser Monitoring System USER MANUAL rev.
DX RF Detector with Real Time remote Monitoring Capability Protect from RF Audio/Video Transmitters and Laser Monitoring System USER MANUAL rev.2 1 Global TSCM Group, Inc. 2 Devine Avenue, Syosset 11791,
More informationOPERATOR MANUAL OSD8865 DIGITAL TRIPLE VIDEO FIBER OPTIC RECEIVER
OPERATOR MANUAL OSD8865 DIGITAL TRIPLE VIDEO FIBER OPTIC RECEIVER INDEX 1 1 TECHNICAL SUMMARY... 4 1.1 BRIEF DESCRIPTION... 4 1.1.1 OVERVIEW... 4 1.1.2 APPLICATIONS... 4 1.1.3 FEATURES AND BENEFITS...
More informationINT-DS2 DVB-S/S2 SATELLITE MODULATOR DVB MODULATOR
INT-DS2 DVB-S/S2 SATELLITE MODULATOR Key Features In compliance with DVB-S/S2/DSNG and in partial compliance with DVB-S2x standards. Supporting up to 200Mbps at ASI and 80Mbps at TSoIP input. Capable to
More informationR&S ETH Handheld TV Analyzer Portable DVB-T/H signal analysis up to 3.6/8 GHz
R&S ETH Handheld TV Analyzer Portable DVB-T/H signal analysis up to 3.6/8 GHz Broadcast Product Brochure 02.00 R&S ETH Handheld TV Analyzer At a glance The R&S ETH handheld TV analyzer was specially designed
More informationInstruction Manual Model BlockUpconverter
Instruction Manual Model 2115-55 BlockUpconverter June 2009 - Rev. 0 MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationTelesto Private Wire Modem Manual
Telesto Private Wire Modem Manual Telesto Private Wire Modem Manual Revision History Filenames are: G:\Company\Manuals &graphics\manuals \ReferenceManual\Components\Telesto_modem\Private Wire\Remote\RevA\CompleteManual\TelestoPwModemCover.lwp
More informationPLL2210MW LED Monitor
PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationUser Manual. TCU/RCU RF Head Control Units. TCU/RCU Analogue 11/6/
11/6/2009 www.elber.com elber@elber.it TCU/RCU RF Head Control Units User Manual Elber s.r.l.- Via Pontevecchio, 42W Phone +39-0185.35.13.33 16042 Carasco (GE) Italy Fax +39-0185.35.13.00 1 Sommario 2
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in
More informationTV-880B (KX-518B) (For NTSC)
(without price) TV-880B (KX-518B) (For NTSC) NOV. 1998 TV-880B R CONTENTS SPECIFICATIONS... 1 BLOCK DIAGRAM... 2 ADJUSTMENTS... 3 PRINTED CIRCUIT BOARDS... 5 EXPLODED VIEW... 7 PARTS LIST... 8 SCHEMATIC
More informationPIM Master. Maintenance Manual
Maintenance Manual PIM Master MW8208A, MW8209A, MW8219A Passive InterModulation Analyzer MW8208A: 869 MHz to 894 MHz MW8209A: 925 MHz to 960 MHz MW8219A: 1930 MHz to 1930 MHz and 2110 MHz to 2155 MHz Anritsu
More informationSATFINDER 3 HD SLIM USER GUIDE
SATFINDER 3 HD SLIM USER GUIDE INDEX General Safety..... 3 Key Features..... 4 Panel Keypads... 5 Accesory.. 6 Satellite Search...... 7 Spectrum..... 8 Cross Polarisation... 9 Packet TP Levels.... 9 Multi
More informationDDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1
DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be
More informationHome Roam TV Basic User Manual
Page1 Home Roam TV Basic User Manual Table of Contents 1. Safety Disclaimer... 2 2. Introduction... 2 3. What s in the Box... 2 4. Specifications... 2 5. Unit Functions... 3 5-1. Transmitter Module...
More informationHD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L HD4112 Manual Rev 1 Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1
More informationRadiocontact Ltd Proprietary Information CONTENTS SECTION 1 3
May 2015 CONTENTS SECTION 1 3 1.1 General 3 1.2 Field Trials 3 1.3 Antenna Mounting 4 1.4 Power Supplies 6 1.5 Safety 7 SECTION 2 8 1.6 Introduction 8 SECTION 3 11 1.7 Digilink 5.8 Connection and Setup
More information6170 Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2115-202 Upconverter November 2011, Rev. C MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationOPERATING INSTRUCTIONS TOM-0431IP
OPERATING INSTRUCTIONS TOM-0431IP Table of Contents FCC Information -------------------------------------------------------------------- 2 Safety and Environmental Precautions ------------------------------------------------
More informationAssembly Level Service Guide
Assembly Level Service Guide This guide describes how to service the Agilent 53150A, 53151A, and 53152A Microwave Frequency Counters. The information in this guide applies to instruments having the number
More informationLCD Short Throw Projector Service Manual for EIKI _LC-XIP2610
LCD Short Throw Projector Service Manual for EIKI _LC-XIP2610 Ver. A_01 Date: 11 th, July 11 2 Content Index Revision History...2 Introduction...4 Important Service Information...4 Safety Notice...4 General
More informationEnterview 2 / Enterview 2V 4 WIRE VIDEO DOORPHONE SYSTEM
Enterview / Enterview V WIRE VIDEO DOORPHONE SYSTEM INSTALLATION AND OPERATION. Introduction This Video doorphone System is an easy-to-use system offering many benefits and conveniences, such as relieving
More informationUser manual. Long Range Wireless HDMI/SDI HD Video Transmission Suite
User manual Long Range Wireless HDMI/SDI HD Video Transmission Suite Preface Thanks for purchasing our Long Range Wireless HDMI/SDI HD Video Transmission Suite. Before using this product, read this user
More informationiphone 7 Plus LCD Screen and Digitizer Replacement
iphone 7 Plus LCD Screen and Digitizer Replacement Replace just the bare front panel not including the home/touch ID sensor, front-facing camera and sensor cable, or earpiece speaker in an iphone 7 Plus.
More information