GSM TELEPHONE SGH-X550 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation
|
|
- Eric Simpson
- 5 years ago
- Views:
Transcription
1 GSM TELEPHONE SGH-X550 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions 6. MAIN Electrical Parts List 7. Block Diagrams 8. PCB Diagrams 9. Flow Chart of Troubleshooting 10. Reference data
2 1. Safety Precautions 1-1. Repair Precaution Repair in Shield Box, during detailed tuning. Take specially care of tuning or test, because specipicty of cellular phone is sensitive for surrounding interference(rf noise). Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by the influence of magnetic force. Surely use a standard screwdriver when you disassemble this product, otherwise screw will be worn away. Use a thicken twisted wire when you measure level. therefore error of measurement is few. A thicken twisted wire has low resistance, Repair after separate Test Pack and Set because for short danger (for example an overcurrent and furious flames of parts etc) when you repair board in condition of connecting Test Pack and tuning on. Take specially care of soldering, because Land of PCB is small and weak in heat. Surely tune on/off while using AC power plug, because a repair of battery charger is dangerous when tuning ON/OFF PBA and Connector after disassembling charger. Don't use as you pleases after change other material than replacement registered on SEC System. Otherwise engineer in charge isn't charged with problem that you don't keep this rules. 1-1
3 Safety Precautions 1-2. ESD(Electrostatically Sensitive Devices) Precaution Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD (Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below. You can prevent from ESD damage by static electricity. Remove static electricity remained your body before you touch semiconductor or parts with semiconductor. There are ways that you touch an earthed place or wear static electricity prevention string on wrist. Use earthed soldering steel when you connect or disconnect ESD. Use soldering removing tool to break static electricity., otherwise ESD will be damaged by static electricity. Don't unpack until you set up ESD on product. Because most of ESD are packed by box and aluminum plate to have conductive power,they are prevented from static electricity. You must maintain electric contact between ESD and place due to be set up until ESD is connected completely to the proper place or a circuit board. 1-2
4 2. Specification 2-1. GSM General Specification GSM900 Phase 1 EGSM 900 Phase 2 DCS1800 Phase 1 PCS1900 Freq. Band[MHz] Uplink/Downlink 890~ ~ ~ ~ ~ ~ ~ ~1990 ARFCN range 1~124 0~124 & 975~ ~ ~810 Tx/Rx spacing 45MHz 45MHz 95MHz 80MHz Mod. Bit rate/ Bit Period kbps 3.692us kbps 3.692us kbps 3.692us kbps 3.692us Time Slot Period/Frame Period 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms 576.9us 4.615ms Modulation 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK MS Power 33dBm~5dBm 33dBm~5dBm 30dBm~0dBm 30dBm~0dBm Power Class 5pcl ~ 19pcl 5pcl ~ 19pcl 0pcl ~ 15pcl 0pcl ~ 15pcl Sensitivity -102dBm -102dBm -100dBm -100dBm TDMA Mux Cell Radius 35Km 35Km 2Km - 2-1
5 Speclflcation 2-2. GSM Tx Power Class TX Power control level GSM900 TX Power control level DCS1800 TX Power control level PCS ±2 dbm 0 30±3 dbm 0 30±3 dbm 6 31±2 dbm 1 28±3 dbm 1 28±3 dbm 7 29±2 dbm 2 26±3 dbm 2 26±3 dbm 8 27±2 dbm 3 24±3 dbm 3 24±3 dbm 9 25±2 dbm 10 23±2 dbm 11 21±2 dbm 12 19±2 dbm 13 17±2 dbm 14 15±2 dbm 4 22±3 dbm 5 20±3 dbm 6 18±3 dbm 7 16±3 dbm 8 14±3 dbm 9 12±4 dbm 10 10±4 dbm 4 22±3 dbm 5 20±3 dbm 6 18±3 dbm 7 16±3 dbm 8 14±3 dbm 9 12±4 dbm 10 10±4 dbm 15 13±2 dbm 11 8±4dBm 11 8±4dBm 16 11±3 dbm 12 6±4 dbm 12 6±4 dbm 17 9±3dBm 13 4±4 dbm 13 4±4 dbm 18 7±3 dbm 14 2±5 dbm 14 2±5 dbm 19 5±3 dbm 15 0±5 dbm 15 0±5 dbm 2-2
6 3. Operation Instruction and Installation Main Function SMS/EMS/MMS Message Service WAP2.0 Speaker phone TFT 1.9" Main Display Dual Display VGA Camera Folder 16 Poly Melody client Bluetooth 3-1
7 Operation Instruction and Installation 3-2
8 4. Array course control 4-1. Software Adjustments Serial Cable(CSA LL64151-A) Power Cable USB DATA CABLE (CSA LL11105 AWM) JIG BOX (GH A) JIG CABLE (GH A) 4-1
9 Array course control 4-2. Software Downloading Pre-requsite for Downloading Downloader Program(S_Benz Downloader_V2.0.exe) X550 Mobile Phone Data Cable Binary file, TFS file S/W Downloader Program Load the binary download program by executing the "S_Benz Downloader_V2.0.exe 1. Select the connected serial port and the rate of speed 2. Select the check box, the mode you want to download. - if the binary file wanted, check only 'BIN' - if the tfs file wanted, check only 'TFS' - if all the files wanted, check 'BIN+TFS' 4-2
10 Array course control 3. Select the file(s) what you want to download 4-3
11 Array course control 4-4
12 5. Exploded View/Disassembly&Assembly Instructions 5-1. Cellular phone Exploded View QRF03 QIF01 QFR01 QFU01 QKP01 QME01 QME16 QLC01 QMW01 QSP01 QMO01 QVK01 QAN05 QCR05 QMP01 QMI01 QCA01 QAN02 QHI01 QFL01 QRE01 QVO01 QCR31 QCR05 QSC01 QBA01 QBA00 5-1
13 Exploded View/Disassembly&Assembly Instructions 5-2. Cellular phone Parts list Design LOC Description Sec Code QAN02 INTENNA-SGH X550 GH A QAN05 ASSY MEC-INTENNA CONTACT GH A QBA00 PCT CASE-BATT TFC(XEC) GH A QBA01 INNER BATTERY PACK-800MAH,MAIN GH A QCA01 UNIT-SGHX550 CAMERA MODULE GH A QCR05 SCREW-MACHINE QCR05 SCREW-MACHINE QCR31 SCREW-MACHINE QFU01 ASSY CASE-FOLDER UPPER(XEC) GH A QKP01 ASSY KEYPAD-(XET/RED) GH B QME01 UNIT-METAL DOME GH A QME16 UNIT-CON TO CON ASSY GH A QMI01 MICROPHONE-ASSY GH A QMO01 MOTOR DC-SGHX550 GH A QMP01 PBA MAIN-SGHX550 GH A QRE01 ASSY CASE-REAR COVER GH B QSC01 RMO-RUBBER SCREW CAP GH B QSP01 SPEAKER QVK01 UNIT-VOLUME KEY GH A QVO01 PMO-VOLUME KEY V2 GH A QLC01 ELA ETC-SGH X550 LCD MODULE GH A QMW01 ASSY COVER-MAIN WINDOW GH A QFR01 ASSY CASE-FRONT COVER GH B QIF01 PMO-COVER IF GH B QRF03 PMO-COVER EAR JACK V2 GH B QFL01 ASSY CASE-FOLDER LOWER GH B QHI01 ASSY HINGE-FOLDER GH A 5-2
14 Exploded View/Disassembly&Assembly Instructions Description Sec Code BAG PE ADAPTOR-SGHD500 TA GH A LABEL(R)-WATER SOAK GH A LABEL(R)-MAIN(EU) GH A MANUAL USERS-XEC SPANISH GH A BOX-UNIT(XEC) GH B CUSHION PLUP-CASE(XEC) GH A MPR-REMOVE TAPE LCD GH A MPR-TAPE LCD CONN COVER GH A MPR-TAPE LED GH A MPR-INSU TAPE GH A MPR-VINYL BOHO MAIN WINDOW GH A MPR-INSU TAPE SUB LCD GH A MPR-INSU TAPE GH A MPR-TAPE GH A MPR-TAPE MAIN FPCB GH A TAPE GASK GH A SPONGE-PBA IF GH A TAPE-FPCB HOLE MASK GH A TAPE-LED MASKING GH A 5-3
15 Exploded View/Disassembly&Assembly Instructions 5-3. Disassembly and Assembly Instructions Disassembly 1 2 1) Unscrew the REAR at the 4 points. 1) Disassemble the REAR from the LOWER using a diassembly stic. 1) Be careful not to make scratch and molding damage! 3 1) Be careful not to make scratch and molding damage! 2) Please remove the lower end locker first. 4 1) Detach the volume key F-PCB, LCD CONNECTOR and MIC from the FRONT ASS'Y. 2) Disassemble the PBA from the FRONT ASS'Y. 1) Disassemble the KEYPAD. 2) Detach the DUST PROTECTION TAPE from the LOWER. 1) Be careful not to damage F-PCBs. (Volume key, LCD, MIC) 1) Be careful not to make scratch and damage to the LCD F-PCB. 5-4
16 Exploded View/Disassembly&Assembly Instructions 5 6 1) Push the hinge between FOLDER UPPER and FOLEDR LOWER, and disassemble the FRONT from the FOLDER. 1) Remove screw rubber caps and unscrew the FOLDER UPPER at the 2 point. 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage CON TO CON FPCB! 1) Be careful not to make scratch and molding damage! 7 8 1) By using an assembly stick, disassemble FOLDER UPPER from FOLDER LOWER (Use disassemble hole) 1) Disassemble the MOTOR, SPEAKER & CAMERA from the FOLDER LOWER by using a pincette. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage F-PCBs and Wire. 5-5
17 Exploded View/Disassembly&Assembly Instructions ) Detatch insulation tapes of the connectors. 2) Disassemble the LCD F-PCB and CAMERA module from the LCD module. 1) Disassemble the LCD module from the FOLDER LOWER. 1) Be careful not to make scratch and molding damage. 2) Be careful not to damage F-PCBs. 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage the LCD module. 5-6
18 Exploded View/Disassembly&Assembly Instructions Assembly 1 2 1) Insert the LCD & CAMERA F-PCB to LCD module. 2) Attach the insulation tape on the connectors. 1) Insert the LCD F-PCB into the FOLDER LOWER. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage the LCD F-PCB ) Insert the SPEAKER into FOLDER LOWER. 2) Twist MOTOR wire third times and insert into the FOLDER LOWER. 1) Insert the CAMERA module into the FOLDER LOWER. 1) Be careful not to make scratch and molding damage! 2) Arrange Wires clearly as above picture is shown. 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage the CAMERA F-PCB. 5-7
19 Exploded View/Disassembly&Assembly Instructions 5 1) Assemble FOLDER UPPER with FOLDER LOWER from the upper end to the lower end. 6 1) Screw up the FOLDER LOWER at two point. 2) Attach screw rubber caps on the screws by using a pincette. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! Use 1.1 ± 0.1 Kgf Cm 7 1) Insert LCD FPCB(which is connected to folder)into the bottom of FRONT HINGE. 2) The folder HINGE sould be inserted into the front's hole. 3) Assemble FOLDER with FRONT. 8 1) Attach the dust protection tape on the inside of the FRONT. 1) Be careful not to make scratch and molding damage. 2) Be careful not to damage LCD F-PCB. 1) Be careful not to make scratch and molding damage. 5-8
20 Exploded View/Disassembly&Assembly Instructions 9 1) Insert the KEYPAD into FRONT. 10 1) Put the PBA on the FRONT ASS'Y. 2) Joint CON to CON FPCB with the PBA. 3) Attach the Volume key F-PCB to the FRONT. 4) Put the MIC on the FRONT MIC HOLE. 1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage! 2) Be careful not to unstably connect CON TO CON. 11 1) Locate VOLUME KEY and assemble REAR with 12 FRONT. 2) Assembly the upper side of the REAR like the picture. 1) Screw the REAR at 4 point 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage LOCKER. 1) Be careful not to make scratch and molding damage! 2) Be careful not to damage LOCKER. 3) Use 1.3 ± 0.1 Kgf Cm 5-9
21 Exploded View/Disassembly&Assembly Instructions 5-10
22 6. MAIN Electrical Parts List Design LOC Description SEC Code STATUS ANT200 NPR-ANTENNA CONTACT GH A SA ANT201 NPR-ANTENNA CONTACT GH A SA ANT600 ANTENNA-CHIP SA BAT500 BATTERY-LI(2ND) SA BTC700 HEADER-BATTERY SA C100 C-CER,CHIP SA C101 C-CER,CHIP SA C102 C-CER,CHIP SA C103 C-CER,CHIP SA C104 C-CER,CHIP SA C105 C-CER,CHIP SA C106 C-CER,CHIP SA C107 C-CER,CHIP SA C108 C-CER,CHIP SA C109 C-CER,CHIP SA C110 C-CER,CHIP SA C111 C-CER,CHIP SA C112 C-CER,CHIP SA C113 C-CER,CHIP SA C114 C-CER,CHIP SA C115 C-CER,CHIP SA C116 C-CER,CHIP SA C117 C-CER,CHIP SA C118 C-CER,CHIP SA C119 C-CER,CHIP SA C120 C-CER,CHIP SA C121 C-CER,CHIP SA C122 C-CER,CHIP SA C123 C-CER,CHIP SA C124 C-CER,CHIP SA C125 C-CER,CHIP SA C126 C-CER,CHIP SA C127 C-CER,CHIP SA C128 C-CER,CHIP SA C129 C-CER,CHIP SA C130 C-CER,CHIP SA C131 C-CER,CHIP SA C132 C-CER,CHIP SA C133 C-CER,CHIP SA C134 C-CER,CHIP SA C200 C-CER,CHIP SA C201 C-CER,CHIP SA C202 INDUCTOR-SMD SA C203 C-CER,CHIP SA C204 C-CER,CHIP SA C205 C-CER,CHIP SA C206 C-CER,CHIP SA C207 C-CER,CHIP SA C209 C-CER,CHIP SA C210 C-CER,CHIP SA C211 C-CER,CHIP SA C212 C-CER,CHIP SA C214 C-CER,CHIP SA 6-1
23 Main Electrical Parts List Design LOC Description SEC Code STATUS C215 C-CER,CHIP SA C216 C-CER,CHIP SA C300 C-CER,CHIP SA C301 C-CER,CHIP SA C302 C-CER,CHIP SA C303 C-CER,CHIP SA C304 C-CER,CHIP SA C305 C-CER,CHIP SA C306 C-CER,CHIP SA C307 C-CER,CHIP SA C308 C-CER,CHIP SA C309 C-CER,CHIP SA C310 C-CER,CHIP SA C311 C-CER,CHIP SA C312 C-CER,CHIP SA C314 C-CER,CHIP SA C315 C-CER,CHIP SA C325 C-CER,CHIP SA C326 C-CER,CHIP SA C400 C-CER,CHIP SA C401 C-CER,CHIP SA C402 C-CER,CHIP SA C403 C-CER,CHIP SA C404 C-CER,CHIP SA C405 C-CER,CHIP SA C406 C-CER,CHIP SA C407 C-CER,CHIP SA C408 C-CER,CHIP SA C410 C-CER,CHIP SA C411 C-CER,CHIP SA C502 C-CER,CHIP SNA C506 C-CER,CHIP SA C507 C-CER,CHIP SA C508 C-CER,CHIP SA C509 C-CER,CHIP SA C510 C-CER,CHIP SA C511 C-CER,CHIP SA C512 C-CER,CHIP SA C513 C-CER,CHIP SA C515 C-CER,CHIP SA C516 C-CER,CHIP SA C518 C-CER,CHIP SA C520 C-CER,CHIP SA C521 C-CER,CHIP SA C522 C-CER,CHIP SA C523 C-CER,CHIP SNA C524 C-CER,CHIP SA C526 C-CER,CHIP SA C600 C-CER,CHIP SA C601 C-CER,CHIP SA C602 C-CER,CHIP SA C603 C-CER,CHIP SA C604 C-CER,CHIP SA 6-2
24 Main Electrical Parts List Design LOC Description SEC Code STATUS C607 C-CER,CHIP SA C608 C-CER,CHIP SA C609 C-CER,CHIP SA C610 C-CER,CHIP SA C611 C-CER,CHIP SA C612 C-CER,CHIP SA C613 C-CER,CHIP SA C614 C-CER,CHIP SA C700 C-CER,CHIP SA C701 C-CER,CHIP SA C702 C-CER,CHIP SA C704 C-CER,CHIP SA C706 C-CER,CHIP SA C707 C-CER,CHIP SA C708 C-CER,CHIP SA C710 C-CER,CHIP SA C712 C-CER,CHIP SA C713 C-CER,CHIP SA C714 C-CER,CHIP SA C717 C-CER,CHIP SA C718 C-CER,CHIP SA C720 C-CER,CHIP SA C721 C-CER,CHIP SA C722 C-CER,CHIP SA C723 C-CER,CHIP SA C724 C-CER,CHIP SA C725 C-CER,CHIP SA C726 C-CER,CHIP SA C727 C-CER,CHIP SA C728 C-CER,CHIP SA C729 C-CER,CHIP SA C800 C-CER,CHIP SA C801 C-CER,CHIP SA C803 C-CER,CHIP SA C804 C-CER,CHIP SA C805 C-CER,CHIP SA C806 C-CER,CHIP SA C807 C-CER,CHIP SA C808 C-CER,CHIP SA C809 C-CER,CHIP SA C810 C-CER,CHIP SA C811 C-CER,CHIP SA C812 C-CER,CHIP SA C819 C-CER,CHIP SA C820 C-CER,CHIP SA C821 C-CER,CHIP SA C822 C-CER,CHIP SA D700 DIODE-TVS SA D702 DIODE-TVS SA D703 DIODE-TVS SA D704 DIODE-TVS SA D705 DIODE-TVS SA D706 DIODE-TVS SA 6-3
25 Main Electrical Parts List Design LOC Description SEC Code STATUS D707 DIODE-TVS SA D708 DIODE-TVS SA D711 VARISTOR SA D712 DIODE-TVS SA D714 DIODE-TVS SA D800 DIODE-TVS SA D801 DIODE-TVS SA DUF200 DUPLEXER-FEM SA EAR700 JACK-PHONE SA F200 FILTER-EMI SMD SA F600 FILTER-LC SA F700 FILTER-EMI/ESD SA HEA800 HEADER-BOARD TO BOARD SA IFC700 CONNECTOR-INTERFACE SA L100 INDUCTOR-SMD SA L101 INDUCTOR-SMD SA L102 INDUCTOR-SMD SA L103 INDUCTOR-SMD SA L104 INDUCTOR-SMD SA L106 INDUCTOR-SMD SA L107 INDUCTOR-SMD SA L108 INDUCTOR-SMD SA L109 INDUCTOR-SMD SA L110 INDUCTOR-SMD SA L111 INDUCTOR-SMD SA L112 INDUCTOR-SMD SA L113 INDUCTOR-SMD SA L114 INDUCTOR-SMD SA L115 INDUCTOR-SMD SA L116 INDUCTOR-SMD SA L117 INDUCTOR-SMD SA L118 INDUCTOR-SMD SA L119 INDUCTOR-SMD SA L120 INDUCTOR-SMD SA L121 INDUCTOR-SMD SA L122 INDUCTOR-SMD SA L123 INDUCTOR-SMD SA L201 INDUCTOR-SMD SA L203 INDUCTOR-SMD SA L204 INDUCTOR-SMD SA L205 INDUCTOR-SMD SA L601 BEAD-SMD SA L700 BEAD-SMD SA L701 BEAD-SMD SA LED701 LED SA LED702 LED SA OSC100 OSCILLATOR-VCTCXO SA OSC300 CRYSTAL-SMD SA PAM200 IC-POWER AMP SA Q400 FET-SILICON SA R100 INDUCTOR-SMD SA R101 R-CHIP SA R102 R-CHIP SA 6-4
26 Main Electrical Parts List Design LOC Description SEC Code STATUS R103 R-CHIP SA R104 R-CHIP SA R105 R-CHIP SA R106 R-CHIP SA R107 R-CHIP SA R108 R-CHIP SA R109 R-CHIP SA R110 R-CHIP SA R111 R-CHIP SA R112 R-CHIP SA R113 R-CHIP SA R114 R-CHIP SA R115 R-CHIP SA R116 R-CHIP SA R117 R-CHIP SA R200 R-CHIP SA R300 R-CHIP SA R301 R-CHIP SA R302 R-CHIP SA R303 R-CHIP SA R308 R-CHIP SA R309 R-CHIP SA R310 R-CHIP SA R311 R-CHIP SA R312 R-CHIP SA R314 R-CHIP SA R315 R-CHIP SA R316 R-CHIP SA R317 R-CHIP SA R318 R-CHIP SA R319 R-CHIP SA R320 R-CHIP SA R403 R-CHIP SA R404 R-CHIP SA R405 R-CHIP SA R406 R-CHIP SA R407 R-CHIP SA R408 R-CHIP SA R409 R-CHIP SA R410 R-CHIP SA R411 R-CHIP SA R412 R-CHIP SA R413 R-CHIP SA R416 R-CHIP SA R417 R-CHIP SA R418 R-CHIP SA R502 R-CHIP SA R503 R-CHIP SA R504 R-CHIP SA R505 R-CHIP SA R508 R-CHIP SA R509 R-CHIP SA R510 R-CHIP SA 6-5
27 Main Electrical Parts List Design LOC Description SEC Code STATUS R511 R-CHIP SA R600 R-CHIP SA R602 R-CHIP SA R607 R-CHIP SA R608 R-CHIP SA R609 R-CHIP SA R610 R-CHIP SA R611 R-CHIP SA R612 R-CHIP SA R613 R-CHIP SA R615 R-CHIP SA R616 R-CHIP SA R700 R-CHIP SA R701 R-CHIP SA R702 R-CHIP SA R704 R-CHIP SA R705 R-CHIP SA R706 R-CHIP SA R707 R-CHIP SA R708 R-CHIP SA R709 R-CHIP SA R710 R-CHIP SA R713 R-CHIP SA R714 R-CHIP SA R715 R-CHIP SA R716 R-CHIP SA R717 R-CHIP SA R719 R-CHIP SA R720 R-CHIP SA R721 R-CHIP SA R723 R-CHIP SA R724 R-CHIP SA R725 R-CHIP SA R726 R-CHIP SA R727 R-CHIP SA R738 R-CHIP SA R739 R-CHIP SA R740 R-CHIP SNA R744 R-CHIP SA R745 R-CHIP SA R746 R-CHIP SA R753 R-CHIP SA R754 R-CHIP SA R755 R-CHIP SA R756 R-CHIP SA R757 R-CHIP SA RFS200 CONNECTOR-COAXIAL SA SIM500 CONNECTOR-CARD EDGE SA SW600 IC-HALL EFFECT S/W SA TA200 C-TA,CHIP SA TA507 C-TA,CHIP SA TA606 C-TA,CHIP SA TA700 C-TA,CHIP SA 6-6
28 Main Electrical Parts List Design LOC Description SEC Code STATUS TH300 THERMISTOR-NTC SA TR700 TR-DIGITAL SA U100 IC-TRANSCEIVER SA U401 IC ASIC-SGHE420 GH A SA U402 FET-SILICON SA U500 IC-POWER SUPERVISOR SA U502 IC-CMOS LOGIC SA U600 IC-CMOS LOGIC SA U601 IC-ANALOG MULTIPLEX SA U606 IC-DATA COMM./GEN SA U608 IC-BATTERY SA U700 IC-POSI.FIXED REG SA U701 IC-VOLTAGE COMP SA U707 IC-AUDIO AMP SA U709 IC-ANALOG MULTIPLEX SA U973 INDUCTOR-SMD SA UCP300 IC-COMM. CONTROLLER SA UME400 IC-MCP SA V500 VARISTOR SA V800 VARISTOR SA V801 VARISTOR SA V802 VARISTOR SA V803 VARISTOR SA V804 VARISTOR SA V805 VARISTOR SA V806 VARISTOR SA V807 VARISTOR SA V809 VARISTOR SA V810 VARISTOR SA V811 VARISTOR SA V812 VARISTOR SA X500 CRYSTAL-SMD SA ZD700 DIODE-ZENER SA ZD701 DIODE-TVS SA ZD705 DIODE-TVS SA 6-7
29 Main Electrical Parts List 6-8
30 7. Block Diagrams 7-1. RF Solution Block Diagram MV
31 (:_C_LKLMCHD(:A(:)Block Diagrams 7-2. Base Band Solution Block Diagram EAR_P RCV_P RCV_N AMP (TAP6201) SPK VDD1 VDD2 SCL SDA IT_PMU EAR_N ANL S/W (STG3699) SPK_P SPK_N MIC VDD3 +AVDD VCC_SYN MIC_BIAS PCF50603 REF_ON 32K SIM CARD MOTOR OM 6357EL4 MAIN CHIP DCL DU DD MIC_P MIC_N B/T (BC313141) EAR_MIC_P EAR_MIC_N HEADSET VDD_RX_TX LDO DAUL LDO Li-ion Battery (standard) ISL6294 CHARGE IC 0077MEMORY NOR FLASH 128M SDRAM 64MHHD(0:7) Y)LD(0:7) KLCD_CS_M LCD_CS_SP(CAMERA) 07)MV3015SAQ VGA CAMERA MAIN LCD TFT 1.9 SUB LCD 4-Gray
32 8. PCB Diagrams Top 8-1
33 PCB Diagrams Bottom 8-2
34 9. Flow Chart of Troubleshooting 9-1. Power On ' Power On ' does not work Check the Battery Voltage is more than 3.4V Change the Battery C507(VINT) = 2.7V? Check the PMU related to VINT Check the Clock at R502=32KHZ Resolder X500 C521(VDD2) & C522(VDD3) ="H"? Check the related circuit C512(VDD1) =1.8V? Check the VDD1(Core voltage)circuit Check for the clock at C110 =13MHz Check the clock generation circuit (related to U100) Check the initial operation END 9-1
35 Flow Chart of Troubleshooting 9-2
36 Flow Chart of Troubleshooting 9-2. Initial Initial Failure R301 (RSTON) ="H"? Check the circuit related to reset Check the 16bit data signal &memoryce END 9-3
37 Flow Chart of Troubleshooting 9-4
38 Flow Chart of Troubleshooting 9-3. Charging Part Abnormal charging part Check the U608 pin 1 >4.9V Check the circuit related to V_EXT_CHARGE U608 pin 4 = "L"? Resolder or replace U608 Check the U608 pin 8 4.2V Resolder or replace U608 END 9-5
39 Flow Chart of Troubleshooting 9-6
40 Flow Chart of Troubleshooting 9-4. Sim Part Phone can't access SIM Card SIM500 pin 1,5 = "H"? Check the sim charge pump After Power ON, Check SIMCLK Signal on pin3 of SIM500 in a few second Check the Clock After SIM card insert, SIM500 pin 2 = "H(SIM_RST)"? Replace PBA Check the SIM Card END 9-7
41 Flow Chart of Troubleshooting 9-8
42 Flow Chart of Troubleshooting 9-5. Microphone Part Microphone does not work Check the connection from MIC Resolder MIC Check the voltage of MIC BIAS (2.15V). Replace PM IC or PBA Check the circuit from EAR700 to MIC Resolder the Surrounding capacitors Check the MIC Replace the MIC END 9-9
43 Flow Chart of Troubleshooting 9-10
44 Flow Chart of Troubleshooting 9-6. Speaker Part(Melody) Speaker does not work U707 PIN 1 ='H'? Replace UCP300 Is Speaker working? Change the Speaker END 9-11
45 Flow Chart of Troubleshooting 9-12
46 Flow Chart of Troubleshooting 9-7. Key Data Input Check Initial Operation When one of the keys is pushed, is it displayed on LCD? Check the Dome sheet & Key Pad When one of the keys is pushed, KBIO signal is OK? Replace the PBA END 9-13
47 Flow Chart of Troubleshooting 9-8. Receiver Part Receiver does not work Is Receiver working? Resolder UCP300 or change PBA Is Receiver working? Replace the Receiver END 9-14
48 Flow Chart of Troubleshooting 9-9. Back Light (for Color Main LCD) Backlight does not work Is LCD Contrast set on high level in the Menu? Set LCD Contrast on high level U2(LCD MODULE) PIN 2 = H? Check the inserting condition of CON TO CON Resolder UCP300 or change PBA U2PIN8=3.6V? Check the U1 & the related circuit Replace the LCD Module END 9-15
49 Flow Chart of Troubleshooting 9-16
50 Flow Chart of Troubleshooting Key Back Light Main Key LED does not work U700 pin8 = H? Check the UCP300 related to "KEY_LED_ON" END 9-17
51 Flow Chart of Troubleshooting Camera part "Camera" function does not work Check the Camera connector on LCD module. Reconnect the camera module C406 =26MHz? Check U100related to 26Mhz Is there another problem? Replace the camera module END 9-18
52 Flow Chart of Troubleshooting 9-19
53 Flow Chart of Troubleshooting GSM Receiver RX ON RF input : 62CH center freq : 942MHz Amp : -50dBm DUF200 Pin8 >= -65dBm Resolder RFS200,C203,L201 DUF200 5,6 >= -68dBm Check DUF200 pin10,pin12 = L Check ANT Switch control circuit Resolder DUF200 U101 pin 29 >= -70dBm pin 30 >= -70dBm Resolder L101, L102, L103 U101 pin 6,7,8,9 >= 1V U101 pin 10,15>=2.8V Check & Resolder U101, OSC100 RF26MHz, RF PSU Part Resolder U101 Check U500 END 9-20
54 Flow Chart of Troubleshooting GSM Transmitter TX ON (5Level) DUF200 Pin8 >= 20dBm Resolder RFS200,C203,L201 DUF200 pin11 >= 18dBm Check DUF200 pin10 = H (2.6V), 12 = L Check ANT Switch control circuit Change or Resolder C206,C208,C209 PAM100 pin11 >= 18dBm Resolder or Change PAM100 PAM100 pin4 <= -11dBm Check F200, OK? Resolder or Change F200 Check +VBAT or PAM control signal U101 pin 38,39<= 15dB Resolder L111,C115,C116 U101 pin 6,7,8,9 >= 1V U101 pin 10,15 >=2.8V Check & Resolder RFOL signal, RF13MHz, RF PSU Part Resolder U101 Check U500 END 9-21
55 Flow Chart of Troubleshooting DCS Receiver RX ON RF input : 698CH center freq : MHz Amp : -50dBm DUF200 Pin8 >= -65dBm Resolder RFS200,C203,L201 DUF200 1,2 >= -68dBm Check DUF200 pin10,pin12 = L Check ANT Switch control circuit U101 pin 35 >= -70dBm pin 36 >= -70dBm Resolder L107, L108, L109 Resolder DUF200 U101 pin 6,7,8,9 >= 1V U101 pin 10,15 >=2.8V Check & Resolder U100, OSC100 RF26MHz, RF PSU Part Resolder U101 Check U500 END 9-22
56 Flow Chart of Troubleshooting DCS Transmitter TX ON (5Level) DUF200 Pin8 >= 20dBm Resolder RFS200,C203,L201 DUF200 pin13 >= 18dBm Check F100 pin12 = H (2.6V), 10 = L Check ANT Switch control circuit Change or Resolder L205,C213,C214 PAM100 pin15 >= 18dBm Resolder or Change PAM100 PAM100 pin3 <= -11dBm Check F200, OK? Resolder or Change F200 Check +VBAT or PAM control signal U101 pin 1,2<= 15dB Resolder C127,C128,L119 U101 pin 6,7,8,9 >= 1V U101 pin 10,15 >=2.8V Check & Resolder RFOH signal, RF13MHz, RF PSU Part Resolder U101 Check U500 END 9-23
57 Flow Chart of Troubleshooting PCS Receiver RX ON RF input : 660CH center freq : MHz Amp : -50dBm DUF200 Pin8 >= -65dBm Resolder RFS200,C203,L201 DUF200 3,4 >= -68dBm Check DUF200 pin10,pin12 = L Check ANT Switch control circuit U101 pin 32 >= -70dBm pin 33 >= -70dBm Resolder L104, L106 Resolder DUF pin 6,7,8,9 >= 1V U101 pin 10,15 >=2.8V Check & Resolder U100, OSC100 RF26MHz, RF PSU Part Resolder U101 Check U500 END 9-24
58 Flow Chart of Troubleshooting PCS Transmitter TX ON (5Level) DUF200 Pin8 >= 20dBm Resolder RFS200,C203,L201 DUF200 pin13 >= 18dBm Check F100 pin12 = H (2.6V), 10 = L Check ANT Switch control circuit Change or Resolder L205,C213,C214 PAM100 pin15 >= 18dBm Resolder or Change PAM100 PAM100 pin3 <= -11dBm Check F200, OK? Resolder or Change F200 Check +VBAT or PAM control signal U101 pin1,2 <= 15dBm Resolder C127,C128,L119 U101 pin 6,7,8,9 >= 1V U101 pin 10,15 >=2.8V Check & Resolder RFOH signal, RF13MHz, RF PSU Part Resolder U101 Check U500 END 9-25
59 Flow Chart of Troubleshooting 9-26
60 Flow Chart of Troubleshooting 9-27
61 Flow Chart of Troubleshooting 9-28
62 10. Reference data Reference Abbreviate AAC: Advanced Audio Coding. AVC : Advanced Video Coding. BER : Bit Error Rate BPSK: Binary Phase Shift Keying CA : Conditional Access CDM : Code Division Multiplexing C/I : Carrier to Interference DMB : Digital Multimedia Broadcasting EN : European Standard ES : Elementary Stream ETSI: European Telecommunications Standards Institute MPEG: Moving Picture Experts Group PN : Pseudo-random ise PS : Pilot Symbol QPSK: Quadrature Phase Shift Keying RS : Reed-Solomon SI :ServiceInformation TDM : Time Division Multiplexing TS : Transport Stream 10-1
63 Reference data 10-2
64 GSPN (Global Service Partner Network) Country rth America Latin America CIS Europe China Asia Mideast & Africa Web Site service.samsungportal.com latin.samsungportal.com cis.samsungportal.com europe.samsungportal.com china.samsungportal.com asia.samsungportal.com mea.samsungportal.com This Service Manual is a property of Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. c Samsung Electronics Co.,Ltd Rev.1.0
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D900 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE. SGH-D900i CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation. 4. Array course control
GSM TELEPHONE SGH-D900i GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions
More informationGSM TELEPHONE SGH-J700 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-J700 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. Main Electrical Parts List 7. Block Diagrams
More informationUMTS TELEPHONE SGH-L760 UMTS TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
UMTS TELEPHONE SGH-L760 UMTS TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block
More informationGSM TELEPHONE. SGH-i710 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Operation Instruction and Installation
GSM TELEPHONE SGH-i710 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Operation Instruction and Installation 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions
More informationGSM TELEPHONE SGH-G600 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-G600 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Part List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE SGH-T619 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-T619 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View/Disassembly and Assembly Instructions 6. MAIN Electrical
More informationGSM TELEPHONE SGH-E380 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-E380 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationSERVICE Manual GSM TELEPHONE SGH-E Specification. 2. Flow Chart of Troubleshooting. 3. Exploded Views and Parts List. 4. Electrical Parts List
GSM TELEPHONE SGH-E310 SERVICE Manual GSM TELEPHONE CONTENTS 1. Specification 2. Flow Chart of Troubleshooting 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams
More informationSERVICE Manual GSM TELEPHONE SGH-E Specification. 2. Flow Chart of Troubleshooting. 3. Exploded Views and Parts List. 4. Electrical Parts List
GSM TELEPHONE SGH-E300 SERVICE Manual GSM TELEPHONE CONTENTS 1. Specification 2. Flow Chart of Troubleshooting 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams
More informationSGH-M Specification. 2. Exploded View and Parts list. 3. Chart of Troubleshooting. 4. Array course control. 5. Block Diagrams. 6.
GSM TELEPHONE SGH-M300 GSM TELEPHONE CONTENTS 1. Specification 2. Exploded View and Parts list 3. Chart of Troubleshooting 4. Array course control 5. Block Diagrams 6. PCB Diagrams 7. MAIN Electrical Parts
More informationGSM TELEPHONE SGH-D830 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-D830 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationGSM TELEPHONE SGH-X500 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-X500 GSM TELEPHONE CONTENTS 1. Safety Precautions. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. Disassembly and Assembly instructions 7.
More informationGSM TELEPHONE SGH-D Specification. 2. Circuit Description. 3. Exploded Views and Parts List. 4. Electrical Parts List. 5.
GSM TELEPHONE SGH-D820 1. Specification 2. Circuit Description 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams 7. Flow Chart of Troubleshooting This Service
More informationapple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple
More informationMASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz
Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO
More informationGSM TELEPHONE SGH-D807 GSM TELEPHONE. CONTENTS 1. Safety Precautions. 2. General Introduction. 3. Specification. 4.
GSM TELEPHONE SGH-D807 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. General Introduction 3. Specification 4. Product Function 5. Circuit Description 6. Test Command & Test Procedure 7. Array course
More informationSGH-M Specification. 2. Exploded View and Parts list. 3. Chart of Troubleshooting. 4. Array course control. 5. Block Diagrams. 6.
GSM TELEPHONE SGH-M300 GSM TELEPHONE CONTENTS 1. Specification 2. Exploded View and Parts list 3. Chart of Troubleshooting 4. Array course control 5. Block Diagrams 6. PCB Diagrams 7. MAIN Electrical Parts
More informationGSM TELEPHONE SGH-E360 CONTENTS GSM TELEPHONE. 1. Specification. 2. Circuit Description. 3. Exploded Views and Parts List. 4. Electrical Parts List
GSM TELEPHONE SGH-E360 GSM TELEPHONE CONTENTS 1. Specification 2. Circuit Description 3. Exploded Views and Parts List 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams 7. Flow Chart of Troubleshooting
More informationSPECIFICATION. DVB-T / Worldwide NIM Tuner
1.Feature * DVB-T demodulator for COFDM with excellent multipath performance, meeting: * DVB-T Digital Television Standard ETS 300744 * Nordig-Unified v1.0.3 Receiver Specification 2.Applications * Digital
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationAVE HOME FAGOR CVBS TO DVB-T ENCODER MODULATOR. Fagor Electr6nica
AVE HOME CVBS TO DVB-T ENCODER MODULATOR FAGOR Fagor Electr6nica TABLE OF CONTENTS 1. SPECIFICATIONS... 12 1.1 Product Overview... 12 1.2 Appearance and Description... 12 1.3 Diagram... 13 1.4 Characteristics...
More informationGSM TELEPHONE SGH-P310 GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-P310 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts List 6. MAIN Electrical Parts List 7. Block Diagrams
More informationJinyoung Contech Co., Ltd.
TO : Jinyoung Contech Co., Ltd. #501, 222-12 MARIOTOWER, GURO-DONG, GURO-KU, SEOUL, KOREA TEL : 82-2-890-6400 FAX : 82-2-890-6406 HOME PAGE : http://www.jyct.com/ Issued Date : 2006-12-15 Page : 13ages
More informationUser Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor
Touch Display LCD Monitor User Manual Installation Guide 15 Resistive Touch LCD Monitor MODEL: KK1500-TR i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com User
More informationapple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber Apple Computer, Inc. All rights reserved.
apple Service Source Apple Studio Display 17" LCD (ADC) Updated 6 Decenber 2004 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Studio Display 17" LCD (ADC) 2003 Apple
More informationFixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationIC-F300/F400/S SERIES PRECAUTIONS
SCRAMBLER UNIT INSTALLATION INSTRUCTIONS UT-109/UT-110 Rev.1.2 Thank you for purchasing the UT-109/UT-110 SCRAMBLER UNIT. The UT-109 and UT-110 are designed for Icom F series VHF/UHF FM transceivers. Please
More informationModification Information (MOD) For. Last Updated: Sep, Type:
Modification Information (MOD) For TKR-750/850 Version2 TKR-751/851 Version: 1.02 USA Last Updated: Sep, 2005 Language: English Type: K About Copyright All copyrights and other intellectual property rights
More informationPLL1920M LED LCD Monitor
PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6
More informationIt will cause malfunction if the monitor is operating with unspecified power supply
User Manual / Installation Guide Model No. PTM-1525R/RT Warning! It will cause malfunction if the monitor is operating with unspecified power supply unit or incorrect power voltage. Do not exposure this
More informationDEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide
DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide SPECIFICATIONS Noise Figure: < 0.8 db Gain: > 15 db Frequency Range: 3400-3500 MHz Input Voltage: 7-16 VDC Description: The 9ULNACK
More informationSquareLED - Aura Bar & Matrix Beam Light 100
SquareLED - Aura Bar & Matrix Beam Light 100 1. SAFETY INSTRUCTIONS Please read these instructions carefully they include the important information about the installation usage and maintenance of this
More informationUser Manual MODEL: KKF1500-PCAP. True FLAT P-CAP LCD Monitor. Installation Guide. 15 True FLAT P-CAP Touch LCD Monitor
True FLAT P-CAP LCD Monitor User Manual Installation Guide 15 True FLAT P-CAP Touch LCD Monitor MODEL: KKF1500-PCAP i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com
More informationSPECIFICATION. DVB-T/ DVB-C / Worldwide hybrid Switchable NIM Tuner
1.Feature *. Integrated RF switch, NTSC VIF demodulator, COFDM demodulator *. All-in-one full NIM function with compact size, optimal solution for cost reduction and shortening product development lead-time.
More informationINSTALLATION MANUAL FT-FOTR-1VDE-ST-S
INSTALLATION MANUAL FT-FOTR-1VDE-ST-S 1-Channel Digital Duplex Baseband Video Transmitter and Receiver With Reverse Data Transmission & Ethernet Transmission v1.0 4/5/11 1 PACKAGE CONTENTS This package
More informationGSM TELEPHONE. SGH-Z650i GSM TELEPHONE CONTENTS. 1. Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control
GSM TELEPHONE SGH-Z650i GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts list 6. MAIN Electrical Parts List 7. Block
More informationSpecifications. FTS-260 Series
Specifications DVB-S2 NIM Tuner Date : 2014. 03. 26. Revision F2 #1501, Halla sigma Valley, 442-2 Sangdaewon-dong, Jungwon-gu, Sungnam City, Gyeonggi-do, Korea, 462-807 Tel. 86-755-26508927 Fax. 86-755-26505315-1
More informationN3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012
N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking
More informationSGH-U Safety Precautions. 2. Specification. 3. Product Function. 4. Array course control. 5. Exploded View and Parts list
GSM TELEPHONE SGH-U800 GSM TELEPHONE CONTENTS 1. Safety Precautions 2. Specification 3. Product Function 4. Array course control 5. Exploded View and Parts list 6. MAIN Electrical Parts List 7. Disassembly
More informationDM-1CH SD DVB-T MODULATOR INSTRUCTION MANUAL
DM-1CH SD DVB-T MODULATOR INSTRUCTION MANUAL 2. Caution Statements and Table of Contents Table of Contents 2. Caution Statements and Table of contents 3. Important Safety Instructions 4. Important Safety
More informationMAXCOM PRODUCT SPECIFICATIONS FIBER OPTIC VIDEO / AUDIO / ASI LINK. Model MX3257HD. Description. Features. Model Selection Guide
MAXCOM PRODUCT SPECIFICATIONS FIBER OPTIC VIDEO / AUDIO / ASI LINK Model MX3257HD Description The rack-mountable MX3257HD fiber optic video multiplexer is ideal for transmitting 1 channel of video, 2 channels
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Multiplexer Enclosure and Cabling December 00 Figure - Trase Unit and Multiplexer Enclosure BNC Coaxial Cables From s (in order) MULTIPLEXER MODEL: 00B R / / / / / / / 9 0 9 0 Multiplexer
More informationTV-1800C (PAL B / G,H) TV-1800D (PAL I) TV-1800I (PAL B / G) TV-1800N (PAL B / G,H)
< TUNING > (without price) TV-1800C (PAL B / G,H) TV-1800D (PAL I) TV-1800I (PAL B / G) TV-1800N (PAL B / G,H) (KX-523) DEC. 1996 R CONTENTS Page SPECIFICATIONS... 1 BLOCK DIAGRAM... 2 CIRCUIT OPERATIONS...
More information40GBd QSFP+ SR4 Transceiver
Preliminary DATA SHEET CFORTH-QSFP-40G-SR4 40GBd QSFP+ SR4 Transceiver CFORTH-QSFP-40G-SR4 Overview CFORTH-QSFP-40G-SR4 QSFP+ SR4 optical transceiver are base on Ethernet IEEE P802.3ba standard and SFF
More informationSPECIFICATION. Multistandard Demodulator tuner. ATSC/Legacy analog NTSC/BTSC
1.Feature MATSCA-SF is the Multistandard Demodulator ATSC/QAM/NTSC module which integrates product is especially suitable for PVR or PIP-TV application. - Supported modulation standards:. ATSC digital
More informationT3316 IP QAM Modulator User Manual
T3316 IP QAM Modulator User Manual SW Version: 1.02 HW version: 0.70.0.0 Web NMS version: 1.02 Intended Audience About This Manual This user manual has been written to help people who have to use, to integrate
More informationAZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR 15.0 OPEN FRAME MONITOR
AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR 15.0 OPEN FRAME MONITOR PART NUMBER: AOM150X03 SERIES DATE: SEPT 04, 2008 1. Introduction: 1.1 About the Product AOM150Xxx 15.0 Open Frame Monitor
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationOTX Optical Transmitter. Operation Instructions
OTX 1310-10 Optical Transmitter Operation Instructions Operation Instructions OTX 1310-10 Optical Transmitter Table of contents 1. Description...4 1.1. Block Diagram...4 2. Front and rear panel...5 2.1.
More informationA LOW COST TRANSPORT STREAM (TS) GENERATOR USED IN DIGITAL VIDEO BROADCASTING EQUIPMENT MEASUREMENTS
A LOW COST TRANSPORT STREAM (TS) GENERATOR USED IN DIGITAL VIDEO BROADCASTING EQUIPMENT MEASUREMENTS Radu Arsinte Technical University Cluj-Napoca, Faculty of Electronics and Telecommunication, Communication
More informationRF Detector with Real Time remote Monitoring Capability Protect from RF Audio/Video Transmitters and Laser Monitoring System USER MANUAL rev.
DX RF Detector with Real Time remote Monitoring Capability Protect from RF Audio/Video Transmitters and Laser Monitoring System USER MANUAL rev.2 1 Global TSCM Group, Inc. 2 Devine Avenue, Syosset 11791,
More informationACTIVE IF SPLITTER/COMBINER UHP-IFS
ACTIVE IF SPLITTER/COMBINER UHP-IFS GENERAL DESCRIPTION AND INSTALLATION GUIDE DOCUMENT RELEASE 2 [UHP.IFS.2.EN] JUNE 2016 CONTENT Acronyms and Abbreviations... 4 Introduction... 5 Required level of qualification...
More informationOPERATOR MANUAL OSD8865 DIGITAL TRIPLE VIDEO FIBER OPTIC RECEIVER
OPERATOR MANUAL OSD8865 DIGITAL TRIPLE VIDEO FIBER OPTIC RECEIVER INDEX 1 1 TECHNICAL SUMMARY... 4 1.1 BRIEF DESCRIPTION... 4 1.1.1 OVERVIEW... 4 1.1.2 APPLICATIONS... 4 1.1.3 FEATURES AND BENEFITS...
More informationTECHNICAL SUPPORT , or FD151CV-LP Installation and Operation Manual 15.1 Low Profile LCD
TECHNICAL SUPPORT 678-867-6717, or www.flightdisplay.com FD151CV-LP Installation and Operation Manual 15.1 Low Profile LCD FD151CV-LP 15.1" Low Profile LCD 2006 Flight Display Systems. All Rights Reserved.
More informationSingMai Electronics SM06. Advanced Composite Video Interface: HD-SDI to acvi converter module. User Manual. Revision 0.
SM06 Advanced Composite Video Interface: HD-SDI to acvi converter module User Manual Revision 0.4 1 st May 2017 Page 1 of 26 Revision History Date Revisions Version 17-07-2016 First Draft. 0.1 28-08-2016
More informationGood Display Specifications
Specifications Type: Model No. Description: 5.0inch TFT LCD module GD567M03-GTI050TN22 5.0 LCD with 640 x RGB x 480 dots Supports CVBS/Video & VGA input RoHS Compliant Prepared: Xiaoli Lan Checked: Moon
More informationSpecifications. FTS-4335 Series
Specifications DVB-S2 DUAL NIM Date : 2017. 03. 17. Revision F2 #1501, Halla sigma Valley, 442-2 Sangdaewon-dong, Jungwon-gu, Sungnam City, Gyeonggi-do, Korea, 462-807 Tel. 0755-26504227 Fax. 0755-26505315
More informationCVM-WM300. UHF Wireless Microphone USER MANUAL
CVM-WM300 UHF Wireless Microphone USER MNUL Foreword Thanks for purchasing COMIC WM300 UHF wireless microphone. WM300 is an all-metal wireless microphone with dual-transmitter triggered by one receiver,
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationSemiconductor Devices. Microwave Application Products. Microwave Tubes and Radar Components
Microwave Application Products Microwave Tubes and Radar Components Our semiconductor products are mostly analog semiconductors classified broadly into three groups: Bipolar ICs, MOS ICs, and Microwave
More informationHD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L HD4112 Manual Rev 1 Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1
More informationData Sheet. ALM MHz 870 MHz Low Noise, High Linearity Amplifier Module with Fail-Safe Bypass Feature. Description.
ALM-11036 776 MHz 870 MHz Low Noise, High Linearity Amplifier Module with Fail-Safe Bypass Feature Data Sheet Description Avago Technologies ALM-11036 is an easy-to-use GaAs MMIC Tower Mount Amplifier
More informationAlice EduPad Board. User s Guide Version /11/2017
Alice EduPad Board User s Guide Version 1.02 08/11/2017 1 Table OF Contents Chapter 1. Overview... 3 1.1 Welcome... 3 1.2 Launchpad features... 4 1.3 Alice EduPad hardware features... 4 Chapter 2. Software
More informationUser manual. Long Range Wireless HDMI/SDI HD Video Transmission Suite
User manual Long Range Wireless HDMI/SDI HD Video Transmission Suite Preface Thanks for purchasing our Long Range Wireless HDMI/SDI HD Video Transmission Suite. Before using this product, read this user
More informationData Sheet. ALM MHz 915 MHz Low Noise, High Linearity Amplifier Module with Fail-Safe Bypass Feature. Description.
ALM-11136 870 MHz 915 MHz Low Noise, High Linearity Amplifier Module with Fail-Safe Bypass Feature Data Sheet Description Avago Technologies ALM-11136 is an easy-to-use GaAs MMIC Tower Mount Amplifier
More informationDEM K SBH-PW-N
Display Elektronik GmbH LCD MODULE DEM 128064K SBH-PW-N Product Specification Ver.: 0 13/Nov./2009 Version: 0 PAGE: 1 SPECIFICATION FOR LCM MODULE MODULE NO: DEM 128064K SBH-PW-N Customer Approval: SIGNATURE
More informationFLAT DISPLAY TECHNOLOGY
15.0 Open Frame Monitor Model Number: LOF1506xx This product is RoHS compliant SPEC No.: SAS-1008002 Version: 0.0 Issue Date: September 6, 2010 1. Introduction: 1.1 About the Product The LOF1506xx 15.0
More informationFeatures: Compliance: Applications: Warranty: QSFP-40G-LR4-GT 40GBASE-LR4 QSFP+ SMF Module Cisco Compatible
The GigaTech Products is programmed to be fully compatible and functional with all intended CISCO switching devices. This QSFP+ optical transceiver is compliant with SFF-8436 and QSFP+ MSA standards. This
More informationHMC581LP6 / 581LP6E MIXERS - SMT. HIGH IP3 RFIC DUAL DOWNCONVERTER, MHz. Typical Applications. Features. Functional Diagram
Typical Applications The HMC1LP6 / HMC1LP6E is ideal for Wireless Infrastructure Applications: GSM, GPRS & EDGE CDMA & W-CDMA Cellular / 3G Infrastructure Functional Diagram Features +26 dbm Input IP3
More informationTable of Contents. 1. Safety Use. 2. General Description. 3. Connection Diagram. 4. Operations and Management. 4.1 Display Status. 4.
DTM-HD01 Thank you for buying this encoder modulator. Please read this manual carefully to install, use and maintain the encoder modulator in the best conditions of performance. Keep this manual for future
More information6.4 Chassis Monitor Model Number: LCM0642xx. SPEC No.: SAS Version: 0.0 Issue Date: April 16, Introduction:
6.4 Chassis Monitor Model Number: LCM0642xx This product is RoHS compliant SPEC No.: SAS-0908003 Version: 0.0 Issue Date: April 16, 2010 1. Introduction: 1.1 About the Product The LCM0642xx 6.4 Chassis
More information2W Wireless Mobile Video Transmitter (ST6000TKMD) User Manual
2W Wireless Mobile Video Transmitter (ST6000TKMD) User Manual TENG YUANZHI SHENZHEN ELECTRONICS CO.,LTD. 2010.10.23 1 Features Low system latency COFDM modulation, Stable transmission MPEG-2 video compression,
More informationDragon. manual version 1.6
Dragon manual version 1.6 Contents DRAGON TOP PANEL... 2 DRAGON STARTUP... 2 DRAGON STARTUP SCREEN... 2 DRAGON INFO SCREEN... 3 DRAGON MAIN SCREEN... 3 TURNING ON A TRANSMITTER... 4 CHANGING MAIN SCREEN
More informationRF4432 wireless transceiver module
RF4432 wireless transceiver module 1. Description RF4432 adopts Silicon Lab Si4432 RF chip, which is a highly integrated wireless ISM band transceiver. The features of high sensitivity (-121 dbm), +20
More informationP XGA TFT Monitor. User s Manual
P6151 15 XGA TFT Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements
More informationTroubleshooting CS800/LC900 Bikes
Troubleshooting CS800/LC900 Bikes CS800/900LC Bike Troubleshooting Entering the Maintenance Mode 15 Touch Screen: The Maintenance Mode is designed to help the tech determine certain faults in the upper
More informationSola-Sat DVB-S2 Modulator Model MS2-L
Sola-Sat DVB-S2 Modulator Model MS2-L User s Manual NMS Version: V4.01 SW: V0.16 HW: V1.90 Sola-Sat Inc Pompano Beach, Florida TABLE OF CONTENTS CHAPTER 1 PRODUCT OUTLINE... 1 1.1 OUTLINE... 1 1.2 FEATURES...
More informationINSTALLATION MANUAL FT-FOTR-8VD-ST-S. 8-Channel Digital Duplex Baseband Video Transmitter and Receiver With Reverse Data Transmission for PTZ Cameras
INSTALLATION MANUAL FT-FOTR-8VD-ST-S 8-Channel Digital Duplex Baseband Transmitter and Receiver With Reverse Transmission for PTZ Cameras v1.0 4/5/11 1 PACKAGE CONTENTS This package contains: One each
More informationPLL2210MW LED Monitor
PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationI R T Electronics Pty Ltd A.B.N. 35 000 832 575 26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA National: Phone: (02) 9439 3744 Fax: (02) 9439 7439 International: +61 2 9439 3744 +61 2 9439 7439 Email:
More informationDIN Connectors DIN06 E-03
DIN Connectors DIN0 E-0 Contents Introduction HOSIDEN DIN connectors are supplied to electronic equipment manufacturers both in Japan and overseas and are very well accepted because of high quality, a
More informationGeChic Corporation 13F.-4, No.367, Gongyi Road, West District, Taichung City 403 Taiwan (R.O.C.) Customer Service:
GeChic Corporation 13F.-4, No.367, Gongyi Road, West District, Taichung City 403 Taiwan (R.O.C.) Customer Service: +886-4-23198080 Monitor for Laptop 1301 User Manual Table of Contents Chapter 1 Content
More informationBacklight Replacement
Installation Instructions Backlight Replacement Catalog Numbers 2711P-RL7C, 2711P-RL7C2, 2711P-RL10C, 2711P-RL10C2, 2711P-RL12C, 2711P-RL12C2, 2711P-RL15C Topic Page About This Publication 1 Important
More informationDDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1
DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be
More informationDEM A SBH-CW-N
Display Elektronik GmbH LCD MODULE DEM 320240A SBH-CW-N Product specification Version : 0 05/03/2007 SPECIFICATION FOR LCM MODULE DEM 320240A SBH-CW-N Customer Approval: SIGNATURE DATE PREPARED BY (RD
More informationN3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB
N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB Kit Components Item Qty Designator Part Color/Marking PCB 1 LCD Display 1 LCD 1602 Volt Regulator 1 U1 78L05, Black TO-92 Prescaler
More informationMACH3 LaserAce Installation Manual Revision 1. MACH3 LaserAce Installation Manual
WWW.LASERARCADE.COM MACH3 LaserAce Installation Manual Revision 1 MACH3 LaserAce Installation Manual Table of Contents Introduction...1 Parts supplied with MACH3 FNI...1 Why the MACH3 FNI is required...2
More informationINSTALLATION INSTRUCTIONS FOR. MODEL 2230LED
INSTALLATION INSTRUCTIONS FOR MODEL 2230LED www.sportablescoreboards.com 1 Table of Contents MODEL 2230LED... 3 8 X 4 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:...
More information6170 Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2115-202 Upconverter November 2011, Rev. C MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationXTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors
XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only
More informationIPad 4 REPAIR GUIDE. Version Edition
IPad 4 REPAIR GUIDE Version 1 2016 Edition IPad 4 REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND
More informationWileyfox Service Support. Wiley Fox Swift Service Manual
Wiley Fox Swift Service Manual Contents 1. A5042 (WILEY FOX SWIFT) overview... 3 1.1 A5042 (WILEY FOX SWIFT) brief introduction... 3 1.2 Function diagram... 3 1.3 Mainboard component distribution diagram...
More informationTelesto Private Wire Modem Manual
Telesto Private Wire Modem Manual Telesto Private Wire Modem Manual Revision History Filenames are: G:\Company\Manuals &graphics\manuals \ReferenceManual\Components\Telesto_modem\Private Wire\Remote\RevA\CompleteManual\TelestoPwModemCover.lwp
More informationSingMai Electronics SM06. Advanced Composite Video Interface: DVI/HD-SDI to acvi converter module. User Manual. Revision th December 2016
SM06 Advanced Composite Video Interface: DVI/HD-SDI to acvi converter module User Manual Revision 0.3 30 th December 2016 Page 1 of 23 Revision History Date Revisions Version 17-07-2016 First Draft. 0.1
More information19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR
19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR V193/ V220 Series V202 Series USER MANUAL www.viewera.com Rev. 2.0 Table of Contents EMC Compliance......1 Important Precautions...2 1. Package contents....3
More informationTRAINING. Manual. DVD-VCR COMBINATION Chassis : Kaiser SV-DVD440
AUX DVD-VCR COMBINATION Chassis : Kaiser SV-DVD440 ELECTRONICS TRAINING MANUAL SV-DVD440 TRAINING DVD-VCR COMBINATION Manual CONTENTS 1. Precautions 2. Reference Information 3. Product Specification 4.
More informationProduct Specification PE613010
Product Description The is an SPST tuning control switch based on Peregrine s UltraCMOS technology. This highly versatile switch supports a wide variety of tuning circuit topologies with emphasis on impedance
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More information