INSTRUCTIONS and PARTS MANUAL STAND ALONE CDS LINEAR WEAVER

Transcription

1 INSTRUCTIONS and PARTS MANUAL SD ALONE CDS LINEAR WEAVER Please record your equipment identification information below for future reference. This information can be found on your machine nameplate. Model Number Serial Number Date of Purchase Whenever you request replacement parts or information on this equipment, always supply the information you have recorded above. LIT-SALW-IPM-0615 A DIVISION OF WELD TOOLING CORPORATION 280 TECHNOLOGY DRIVE CANONSBURG, PENNSYLVANIA USA PHONE: FAX:

2 SAFETY PROTECT YOURSELF AND OTHERS FROM SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS. ELECTRIC SHOCK can kill. 1. The equipment is not waterproof. Using the unit in a wet environment may result in serious injury. Do not touch equipment when wet or standing in a wet location. 2. The unused connectors have power on them. Always keep the unused connectors covered with the supplied protective panels. Operation of the machine without the protective panels may result in injury. 3. Never open the equipment without first unplugging the power cord or serious injury may result. 4. Verify the customer-supplied power connections are made in accordance with all applicable local and national electrical safety codes. If none exist, use International Electric Code (IEC) Never remove or bypass the equipment power cord ground. Verify the equipment is grounded in accordance with all applicable local and national electrical safety codes. In none exist, use International Electric Code (IEC) 950. EQUIPMENT DAMAGE POSSIBLE. 1. Do not plug in the power cord without first verifying the equipment is OFF and the cord input voltage is the same as required by the machine or serious damage may result. 2. Always verify both the pinion and wheels are fully engaged before applying power or equipment damage may occur. 3. Do not leave the equipment unattended. 4. Remove from the work site and store in a safe location when not in use. FALLING EQUIPMENT can cause serious personal injury and equipment damage. Faulty or careless user installation is possible. As a result, never stand or walk underneath equipment. MOVING PARTS can cause serious injury. READ INSTRUCTIONS. Read the instruction manual before installing and using the equipment. 1. Never try to stop the pinion from moving except by removing power or by using the STOP control. 2. Do not remove any protective panels, covers or guards and operate equipment. 2

3 HIGH FREQUENCY WARNINGS SPECIAL PRECAUTIONS ARE REQUIRED WHEN USING PLASMA, TIG OR ANY WELDING PROCESS THAT USES HIGH FREQUENCY TO STRIKE AN ARC. WARNING: HIGH FREQUENCY CAN EFFECT MACHINE OPERATION AND THEREFORE, WELD QUALITY. Read the precautions below before installing and using the equipment. PRECAUTIONS: 1) Some plasma or welding cables are strong sources of high frequency interference. NEVER lay a plasma or welding cable across the controls of the machine. 2) Always physically separate the plasma or welding cable leads from the machine cables. For example, the plasma or welding cable leads should NEVER be bundled with a pendant cable or the machine power cord. Maximize the separation between any machine cables and the plasma or welding cables. 3) Strictly follow the grounding procedures specified for the plasma or welding unit. NOTE: Some plasma and welding units produce exceptionally large amounts of high frequency noise. They may require a grounding rod be driven into the earth within six feet (2 meters) of the plasma or welding unit to become compatible with an automatic cutting or welding process. 4) If the high frequency is produced using a spark gap, adjust the points so the gap is as small as possible. The larger the gap, the higher the voltage and the higher the interference. 5) Some plasma or welding units will inject high frequency interference into the AC power line. Use separate power line branches whenever possible to power the plasma or welding source and the machine. Do not plug them into the same outlet box. 6) High frequency noise may enter the machine through the plasma or welding supply remote contactor leads. Some plasma and welding sources can produce noise spikes of up to several thousand volts. These sources are not compatible with automated cutting and welding equipment. It is recommended that the remote contactor leads on these plasma or welding sources not be connected to the machine. An alternate solution is to purchase a separate remote contactor isolation box. 3

4 SD ALONE CDS LINEAR WEAVER INSTRUCTIONS AND PARTS MANUAL TABLE OF CONTENTS PAGE 5... Introduction / Features / Technical Data 6... CDS-6350 Standalone Weaver / Major Components 6... CDS-1210 Dimensions 7... CDS-1210 Weaver Unit / Parts List 8... CDS-1215 Weaver Unit Motor Plate Assembly / Parts List 9... CDS-1210 Weaver Unit / Wiring Diagram / Electrical Component Chart CDS-6330 Control Box CDS-6330 Control Box / Exploded View CDS-6330 Control Box / Parts List CDS-6330 Control Box / Wiring Diagram / Electrical Component Chart BUG-5475 Weaver Racking Group / Exploded View / Parts List BUG-6336 Connector Wiring Harness / Wiring Diagram BUG-6337 Timer Wiring Harness / Wiring Diagram BUG-6318 Weave Wiring Harness / Wiring Diagram BUG-5570 Power Circuit Box / Exploded View / Parts List Power Circuit Box / Wiring Diagram Warranty THIS PRODUCT IS COVERED BY ONE OR MORE PATENTS WORLD WIDE. 4

5 INTRODUCTION The Stand Alone CDS Linear Weaver is a self contained machine used for weave welding. It can be installed as part of a welding fixture, or mounted on a drive carriage running on a track. The CDS Linear Weaver is particularly useful for weaving v-groove welds in a butt joint. The Weaver box is attached on the end of an adjustable rack, held by a rackholder that can be mounted on the front of the drive carriage, or directly on the welding fixture. FEATURES High torque, low inertia motor for precise starts and stops. Heavy duty planetary gear box with powerful output shaft. Uniform linear motion with independent control of right and left dwell times. Closed loop speed control for adjustable and repeatable control of critical welding parameters. Closed loop position control to prevent drift from the center position. Gun mounting group with adjustable linkage for accurate positioning of the gun. Weld Contactor ON/OFF switch. TECHNICAL DATA Power Requirement: CDS VAC/50-60/1 CDS VAC/50-60/1 CDS VAC/50-60/1 Weave Speed: 4 to 100 ipm (100 to 2540 mm/min) Dwell: Weave Width: Steering: Dimensions: Net Weight: Shipping Weight: 0-3 seconds Each side, calibrated 0 to 2" (0 to 50 mm) 2" (50 mm) left and right of center 4" (100 mm) total 6.75"L x 5.00"W x 4.88"H (171 x 127 x 124 mm) 20 lbs. (9.07 kg) 25 lbs. (11.34 kg) 5

6 CDS-6350 SD ALONE LINEAR WEAVER / MAJOR COMPONENTS CDS-6330 Control Box CDS-1210 Linear Weaver BUG-5571 Power Cable BUG-5571 Power Cable BUG-5295 Rod Mount Assembly & BUG Rod BUG-5570, BUG-5572, BUG-5574 Power Circuit Box CDS-1210 DIMENSIONS 5" (127 mm) 4.88" (124 mm) 10" (254 mm) " (464 mm) 6.75" (171 mm)

7 CDS-1210 WEAVER UNIT / PARTS LIST , ITEM QTY PART NO. DESCRIPTION 1 2 BUG-5661 Stop Plate 2 1 BUG-9856 Panel Connector, 2-T, Female 3 1 BUG-9909 Panel Connector, 6-T, Male 4 1 CDS-1215 Motor Plate Assembly 5 1 CDS-1217 Panel, Control End 6 1 CDS-1218 Panel 7 1 CDS-1221 Cover 8 14 FAS-0114 Pan Hd Scr 6-32 x 3/8 Lg 9 8 FAS-0204 Rnd Hd Scr 4-40 x 3/8 Lg 10 2 FAS-0357 Hex Hd Cap Scr 1/4-20 x 3/4 Lg 11 8 FAS-1305 Hex Nut BUG-5475 Weaver Racking Group 12 7

8 CDS-1215 WEAVER UNIT MOTOR PLATE ASSEMBLY / PARTS LIST ITEM QTY PART NO. DESCRIPTION 1 1 BUG-5590 Gear Motor 2 1 BUG-5591 Pinion 3 2 BUG-5592 Spacer 4 4 BUG-5594 Pan Hd Scr 3mm x BUG-5595 Pot/Gear Assembly 6 2 BUG-5670 Adj Leg & Wheel Assembly 7 2 BUG-5675 Fixed Leg & Wheel Assembly 8 1 CDS-1216 Mounting Plate 8

9 CDS-1210 WEAVER UNIT / WIRING DIAGRAM / ELECTICAL COMPONENT CHART ELECTRICAL COMPONENT CHART ITEM DESCRIPTION PART NO. M Gear Motor BUG-5590 P Servo Potentiometer BUG-5240 PS Power Supply Connector BUG-9909 TR Tractor Connector BUG

10 CDS-6330 CONTROL BOX STEERING CONTROL WEAVE SPEED AMPLITUDE DWELL LEFT DWELL RIGHT POWER ON/OFF WELD CONTACT WEAVE / NO WEAVE POWER SUPPLY TO PENDULUM GEAR BOX 10

11 CDS-6330 / CONTROL BOX / EXPLODED VIEW

12 CDS-6330 CONTROL BOX / PARTS LIST ITEM QTY PART NO. DESCRIPTION 1 1 CAS-1770 Motor Control Board 2 1 BUG-5757 Knob 3 1 BUG-5760 Control Board 4 1 BUG-6331 Front Panel 5 1 BUG-6332 Rear Panel 6 1 BUG-6333 Mounting Bracket 7 4 BUG-9621 Knob 8 1 CDS-1068 Mounting Bracket 9 8 FAS-0104 Pan Hd. Scr. #4-40 x 3/8 Lg FAS-0114 Pan Hd. Scr. #6-32 x 3/8 Lg FAS-0224 Pan Hd. Scr. #10-32 x 3/8 Lg FAS-0824 Flat Hd. Slt. Scr. #8-32 x 3/8 Lg FAS-1305 Hex Nut #4/ SFX-1292 Bumper 15 8 WAS-0201 #4 Internal Star Lock Washer 16 1 BUG-5761 SW-2 Toggle Switch, SPDT 17 1 ARM-2279 SW-1 Toggle Switch, DPST 18 1 BUG-1869 SW-3 Toggle Switch, SPDT 19 1 BUG-9909 Panel Connector, 6-T, M 20 1 BUG-9902 Panel Connector, 6-T, F 21 3 BUG-9677 Potentiometer, 10K 22 2 BUG-5054 Potentiometer, 500K * 1 BUG-6336 Connector Wiring Harness * 1 BUG-6318 Weave Wiring Harness * 1 BUG-6337 Timer Wiring Harness * not shown 12

13 CDS-6330 CONTROL BOX / WIRING DIAGRAM / ELECTRICAL COMPONENT CHART ELECTRICAL COMPONENTS ITEM PART NO. DESCRIPTION CN-2 BUG-9909 Panel Connector, 6-T, M CN-3 BUG-9902 Panel Connector, 6-T, F P-1,2,3 BUG-9677 Pot, 10 K P-4,P-5 BUG-5054 Pot, 500 K PCB-1 BUG-5760 Control Board PCB-2 CAS-1770 Motor Control Board SW-1 ARM-2279 Toggle Switch, DPST SW-2 BUG-5761 Toggle Switch, SPDT SW-3 BUG-1869 Toggle Switch, SPDT BK RD BU W/BU YL BU PK GY VIO RED SW-3 E D C A B F VIO W/GN W/GN T1 T2 8V STEER -8V OR 8V WV.SPD YEL WH W/GN YL BU BK GN GY RD OR GN A B C F E D 13

14 BUG-5475 WEAVER RACKING GROUP /EXPLODED VIEW / PARTS LIST ITEM QTY PART NO. DESCRIPTION 1 1 BUG-5462 Right Angle Clamp 2 1 BUG-2708 Clamp 3 1 BUG-1853 Machined Rack 7-1/2" 4 1 BUG-2714 Rackrider w/post 5 1 BUG-5695 Cross Arm 14

15 BUG-6336 CONNECTOR WIRING HARNESS / WIRING DIAGRAM CNN-022A 10-PIN HOUSING INCLUDES: (1) CNN-022A-P 10 PIN HOUSING (MOLEX P/N ) (10) CNN-0220 PIN.156 (MOLEX P/N ) BUG-9902 PANEL CONNECTOR 6-T, F (DESC: DMS3102A14S(D235)) WHT/ (A) WHT/ YEL (B) (Z) BLK RED (X) C B VIO A D RED BLK E F BUG-9909 PANEL CONNECTOR 6-T, M (DESC: DMS3102A14S-6P(D235)) WHT/GRN COM A F E D B C YEL WHT/GRN ARM-2279 TOGGLE SWITCH, ON-OFF, DPST (EATON P/N 7310K38) (Z) (A) (X) VIO WHT/GRN (E) WHT/GRN (D) CNN PIN HOUSING INCLUDES: (1) CNN-0128-P 8 PIN HOUSING (MOLEX P/N ) (8) CNN-0120 PIN.100 (MOLEX P/N ) 15

16 BUG-6337 TIMER WIRING HARNESS / WIRING DIAGRAM BUG-6318 WEAVE WIRING HARNESS / WIRING DIAGRAM (3) BUG K-Ohm POT CNN-012A 10-PIN HOUSING GRY RED ORG RED GRY GRN BLK YEL W/GN WHT WHT W/GN GRN RED TEL GRN RED ORG BLK BUG-5761 SWITCH TOGGLE SPDT ON-OFF-ON 16

17 BUG-5570 POWER CIRCUIT BOX / EXPLODED VIEW / PARTS LIST ITEM QTY PART NO. DESCRIPTION 1 1 ARM-2279 Toggle Switch *2 1 BUG-2923 Circuit Breaker.7A 3 1 BUG-2924 Reset Button Seal *4 1 BUG-5218 Transformer 5 1 BUG-5573 Enclosure *6 1 BUG-9445 Power Cord 7 1 BUG-9446 Cord Grip 8 1 BUG-9486 Panel Connector, 2-T, M 9 1 BUG-9487 Cable Connector, 2-T, F 10 1 BUG-9884 On-Off Switch Plate 11 1 BUG-9902 Panel Connector, 6-T, F 12 8 FAS-0204 Rnd Hd Scr 4-40 x 3/ FAS-1224 But Hd Soc Hd Scr 8-32 x 3/ FAS-1305 Hex Nut FAS-1320 Hex Nut SFX-1292 Bumper 17 1 WAS-0221 #8 Star Lockwasher * See Electrical Component Chart for 240 VAC and 42 VAC Part Numbers 17

18 POWER CIRCUIT BOX / WIRING DIAGRAM CN 1 S A RED T CB BLK F B YEL VT GRN PC E C GY WH D WHT/BLK/GR WHT/BLK/GR A B CN 2 ELECTRICAL COMPONENT CHART BUG-5570 BUG-5572 BUG-5574 ITEM DESCRIPTION 120 VAC 240 VAC 42 VAC PART NO. PART NO. PART NO. CB Circuit Breaker BUG-2923 BUG-2952 BUG-2933 PC Power Cord BUG-9445 GOF-3115 BUG-9442 T Transformer BUG-5218 BUG-5231 BUG-5232 VT Volt Trap BUG-1393 BUG-1563 BUG-1393 CN-1 Panel Connector BUG-9902 CN-2 Panel Connector BUG-9486 S Toggle Switch ARM

19 WARRANTY Limited 3-Year Warranty Model Serial No. Date Purchased: Where Purchased: For a period ending one (1) year from the date of invoice, Manufacturer warrants that any new machine or part is free from defects in materials and workmanship and Manufacturer agrees to repair or replace at its option, any defective part or machine. HOWEVER, if the invoiced customer registers the Product Warranty by returning the Warranty Registration Card supplied with the product within 90 days of the invoice date, or by registering on-line at Manufacturer will extend the warranty period an additional two (2) years which will provide three (3) total years from the date of original invoice to customer. This warranty does not apply to machines which, after Manufacture s inspection are determined by Manufacturer to have been damaged due to neglect, abuse, overloading, accident or improper usage. All shipping and handling charges will be paid by the customer. The foregoing express warranty is exclusive and Manufacturer makes no representation or warranty (either express or implied) other than as set forth expressly in the preceding sentence. Specifically, Manufacturer makes no express or implied warranty of merchantability or fitness for any particular purpose with respect to any goods. Manufacturer shall not be subject to any other obligations or liabilities whatsoever with respect to machines or parts furnished by Manufacturer. Manufacturer shall not in any event be liable to Distributor or any customer for any loss of profits, incidental or consequential damages or special damages of any kind. Distributor s or customer s sole and exclusive remedy against Manufacturer for any breach of warranty, negligence, strict liability or any other claim relating to goods delivered pursuant hereto shall be for repair or replacement (at Manufacturer s option) of the machines or parts affected by such breach. Distributor s Warranty: In no event shall Manufacturer be liable to Distributor or to any customer thereof for any warranties, representations or promises, express or implied, extended by Distributor without the advance written consent of Manufacturer, including but not limited to any and all warranties of merchantability or fitness for a particular purpose and all warranties, representations or promises which exceed or are different from the express limited warranty set forth above. Distributor agrees to indemnify and hold Manufacturer harmless from any claim by a customer based upon any express or implied warranty by Distributor which exceeds or differs from Manufacturer s express limited warranty set forth above. HOW TO OBTAIN SERVICE: If you think this machine is not operating properly, re-read the instruction manual carefully, then call your Authorized BUG-O dealer/distributor. If they cannot give you the necessary service, write or phone us to tell us exactly what difficulty you have experienced. BE SURE to mention the MODEL and SERIAL numbers. 19