STC (Dongguan) Company Limited EC VERIFICATION OF COMPLIANCE EMC-D163584VOC

Transcription

1 EC VERIFICATION OF COMPLIANCE Reference Number: Applicant: EMC-D16584VOC Zhuhai Zhi Li Battery Co., Ltd. 7/F., Building 10, Xiang Zhou North Industry Park, Zhuhai, GD , China Description: Zinc Air Button Cell (mercury free) Brand Name: N/A Model (basic): A675 (additional): A10, A12, A1, A675P, PR20, PR240 We verify that the mentioned product complies with the requirements of the EC Electromagnetic Compatibility Directive 2014/0/EU Applicable Standard(s) with amendments: EN : A1: 2011 EN : 2007 General Remarks: This verification confirmation is only valid when used in conjunction with the technical file(s) refers to DM This document applies specifically to the sample(s) investigated in the technical report mentioned above, and not to the bulk. The CE marking as shown below can be affixed on the product after preparation of necessary conformity documentation, as stipulated in articles of above Directive(s). Test Laboratory LONG Yun Jian, Along Authorized Signatory ElectroMagnetic Compatibility Department For and on behalf of Date of Issue:

2 Date: Page 1 of 17 Applicant: Zhuhai Zhi Li Battery Co., Ltd. 7/F., Building 10, Xiang Zhou North Industry Park, Zhuhai, GD , China Description of Sample(s): Submitted sample(s) said to be Product: Zinc Air Button Cell (mercury free) Brand Name: N/A Model Number: A675 Date Sample(s) Received: Date Tested: to Investigation Requested: Test for compliance with EMC requirements of EN , EN Conclusion(s): The submitted product COMPLIED with the requirements of EN : A1:2011 and EN : The EMC tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remark(s): For additional model(s) details, see page LONG Yun Jian, Along Authorized Signatory ElectroMagnetic Compatibility Department For and on behalf of This report shall not be reproduced unless with prior written approval from.

3 Date: Page 2 of 17 CONTENT: Cover Page 1 of 17 Content Page 2 of General Details 1.1 Equipment Under Test [EUT] Page of 17 Description of Sample(s) 1.2 Date of Order Page of Submitted Sample(s) Page of Test Duration Page of Country of Origin Page of Technical Details 2.1 Investigations Requested Page 4 of Test Standards and Results Summary Page 4-5 of 17.0 Test Results.1 Emission Page 6-8 of 17.2 Immunity Page 9-1 of 17 Appendix A List of Measurement Equipment Page 14 of 17 Appendix B Photograph(s) of Product Page of 17 This report shall not be reproduced unless with prior written approval from.

4 Date: Page of General Details 1.1 Equipment Under Test [EUT] Description of Sample(s) Product: Manufacturer: Brand Name: Model Number: Additional Model Number: Rating: Zinc Air Button Cell (mercury free) Zhuhai Zhi Li Battery Co., Ltd. 7/F., Building 10, Xiang Zhou North Industry Park, Zhuhai, GD , China N/A A675 A10, A12, A1, A675P, PR20, PR Vd.c. 1.2 Date of Order Submitted Sample(s): 1 Sample 1.4 Test Duration to Country of Origin China This report shall not be reproduced unless with prior written approval from.

5 Date: Page 4 of Technical Details 2.1 Investigations Requested Perform ElectroMagnetic Interference [EMI] & ElectroMagnetic Susceptibility [EMS] tests for CE Marking 2.2 Test Standards and Results Summary Tables EN : A1:2011 Test Standards Electromagnetic compatibility (EMC) - Part 6-: Generic standards - Emission standard for residential, commercial and light-industrial environments EN : 2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments This report shall not be reproduced unless with prior written approval from.

6 Date: Page 5 of Test Standards and Results Summary Tables EMISSION Results Summary Test Condition Test Requirement Test Method Class / Test Result Severity Pass Failed N/A Radiated Emission, 0MHz to 1GHz EN : A1:2011 EN55022: 2010 Class B IMMUNITY Results Summary Test Condition Test Requirement Test Method Class / Test Result Severity Pass Failed N/A Electrostatic Discharge Radiated Immunity 80MHz to 1000MHz 1400MHz to 2700MHz EN : 2007 EN : kV, 4kV Cont 2kV, 4kV, 8.0kV Air EN : 2007 EN : 2006 V/m 1V/m Remark: N/A: Not Applicable This report shall not be reproduced unless with prior written approval from.

7 Date: Page 6 of 17.0 Test Results.1 Emission.1.1 Radiated Emissions (0MHz to 1000MHz) Test Requirement: EN Test Method: EN Level: Class B Test Date(s): Mode of Operation: On mode Test Method: The test was performed in accordance with EN at m test distance on a standard emission test site, with quasi-peak measurements performed if the maximised peak measurements were less than 6dB from the corresponding Class B limit lines. Test Setup: Semi-Anechoic Chamber m Computer EUT Turntable Measuring Receiver Ground Plane This report shall not be reproduced unless with prior written approval from.

8 Date: Page 7 of 17 Limits for Radiated Emission: Frequency Range Quasi-Peak Limits [MHz] [db V/m] Results of On mode: Pass Please refer to the following table for result details Horizontal The quasi-peak measurements were recorded as follows: Frequency Margin E-Field Polarity MHz db V/m db V/m db Horizontal Horizontal Horizontal This report shall not be reproduced unless with prior written approval from.

9 Date: Page 8 of 17 Limits for Radiated Emission: Frequency Range Quasi-Peak Limits [MHz] [db V/m] Results of On mode: Pass Please refer to the following table for result details Vertical The quasi-peak measurements were recorded as follows: Frequency Margin E-Field Polarity MHz db V/m db V/m db Vertical Vertical Vertical Remark: Calculated measurement uncertainty (0MHz 1GHz): 4.6dB Emissions in the vertical and horizontal polarizations have been investigated and the worst-case test results are recorded in this report. This report shall not be reproduced unless with prior written approval from.

10 Date: Page 9 of 17.2 Immunity.2.1 Susceptibility Performance Criteria A B C D Normal performance within the specification limits Temporary degradation or loss of function or performance which is selfrecoverable Temporary degradation or loss of function or performance which requires operator intervention or system reset Degradation or loss of function which is not recoverable due to damage of equipment (components) or software, or loss of data This report shall not be reproduced unless with prior written approval from.

11 Date: Page 10 of Electrostatic Discharge Test Requirement: EN Test Method: EN Severity: 2kV, 4kV for Direct & Indirect Contact Discharge 2kV, 4kV, 8kV for Air Discharge Performance Criterion Requirement: B Temperature: 2 o C Humidity: 51 % Atmospheric Pressure: 101 kpa Test Date(s): Mode of Operation: On mode Test Method: The test was performed in accordance with EN Test Setup: This report shall not be reproduced unless with prior written approval from.

12 Date: Page 11 of 17 Severity Levels for Electrostatic Discharge: Level Test Voltage Test Voltage Direct & Indirect Contact Air Discharge Discharge 1 2kV 2kV 2 4kV 4kV 6kV 8kV 4 8kV 15kV Results of On mode: Pass Please refer to the following table for individual results. Location Discharge Method Test Voltage HCP [Horizontal Coupling Plane] Indirect Contact 2kV, 4kV VCP [Vertical Coupling Plane] Indirect Contact 2kV, 4kV Metal Air 2kV, 4kV, 8kV Individual Results Pass Failed ***EUT Grounding Grounded Ungrounded Remarks: ***For ungrounded EUT, the charge on the EUT shall be removed prior to each applied ESD pulse Calculated measurement uncertainty: 7.1% This report shall not be reproduced unless with prior written approval from.

13 Date: Page 12 of Radiated Immunity [80MHz to 2700MHz] Test Requirement: EN Test Method: EN Severity: Level 1 [1V/m] Level 2 [V/m] Modulation: 80% 1kHz AM Performance Criterion Requirement: A Temperature: 2 o C Humidity: 55 % Test Date(s): Mode of Operation: On mode Test Method: The test was performed in accordance with EN Test Setup: distance = m Computer EUT Amplifier Absorbers Signal Generator This report shall not be reproduced unless with prior written approval from.

14 Date: Page 1 of 17 Severity Levels for Radiated Immunity: Level Field Strength [V/m] Results of On mode: Pass Please refer to the following table for individual results. Frequency Face Polarity Level Dwell Time Sweep rate Individual Results (MHz) (V/m) (s) (%) Pass Failed o Horizontal 90 o Horizontal 180 o Horizontal 270 o Horizontal o Vertical o Vertical o Vertical 270 o Vertical Remarks: The dwell time at each frequency is according to the standard being applied and the basic standard Calculated measurement uncertainty: 1.74dB This report shall not be reproduced unless with prior written approval from.

15 Date: Page 14 of 17 Appendix A List of Measurement Equipment Radiated Emission EQP NO. DESCRIPTION MANUFACTURER MODEL NO. SERIAL NO. LAST CAL EMD022 EMI Test Receiver ROHDE & SCHWARZ ESCS EMD061 Biconilog Antenna ETS.LINDGREN 142C EMD084 MULTI-DVICE CONTROLLER ETS.LINDGREN N/A EMD088 Video Contol Unit ETS.LINDGREN Y2195A N/A EMD09 Monitor ViewSonic VA906 Q8X N/A EMD102 Intelligent Frequency Ainuo lnstrument Co., Ltd AN97005SS N/A EMD105 FACT- EMC Chamber ETS.LINDGREN FACT- 80 N/A EMD-S01 RE Test software ROHDE & SCHWARZ ESxS-K1 V2.10 N/A Electro Static Discharge EQP NO. DESCRIPTION MANUFACTURER MODEL NO. SERIAL NO. LAST CAL EMD007 HIGH VOLTAGE OUTPUT ±0KV MAX EMD04 Dehumidifier Kawasima electrical appliance Co.,Ltd EMD100 Thermohygrograph SATO KEIRYOKI MFG.CO.,LTD. EMD109 BAROGRAPH SATO KEIRYOKI MFG.CO.,LTD. KIKUSUI KES4021 LG Radiated Field Immunity DH-820H N/A N/A NSII-BQ EQP NO. DESCRIPTION MANUFACTURER MODEL NO. SERIAL NO. LAST CAL EMD111 Power meter ROHDE & SCHWARZ NRVD EMD17 Signal Generator ROHDE & SCHWARZ SMB100A K DF EMD060 Biconilog Antenna ETS.LINDGREN 142C EMD06 Power Amplifier BONN ELEKTRONIK BLWA B /0D EMD064 Power Amplifier BONN ELEKTRONIK BLWA /100D A EMD-S07 RI Test software ROHDE & SCHWARZ EMC2 V N/A Remark: N/A Not Applicable This report shall not be reproduced unless with prior written approval from.

16 Date: Page 15 of 17 Appendix B Photographs of EUT Front View of The Product Rear View of The Product This report shall not be reproduced unless with prior written approval from.

17 Date: Page 16 of 17 Photographs of EUT Radiated Emissions Test Set Up Electro Static Discharge Test Set Up This report shall not be reproduced unless with prior written approval from.

18 Date: Page 17 of 17 Photographs of EUT Radiated Immunity Test Set Up *****End of Test Report***** This report shall not be reproduced unless with prior written approval from.

19 Conditions of Issuance of Test Reports 1. All samples and goods are accepted by The Hong Kong Standards & Testing Centre Limited (the Company ) solely for testing and reporting in accordance with the following terms and conditions. The Company provides its services on the basis that such terms and conditions constitute express agreement between the Company and any person, firm or company requesting its services (the Clients ). 2. Any report issued by the Company as a result of this application for testing service (the Report ) shall be issued in confidence to the Clients and the Report will be strictly treated as such by the Company. It may not be reproduced either in its entirety or in part and it may not be used for advertising or other unauthorized purposes without the written consent of the Company. The Clients to whom the Report is issued may, however, show or send it, or a certified copy thereof prepared by the Company to his customer, supplier or other persons directly concerned. The Company will not, without the consent of the Clients, enter into any discussion or correspondence with any third party concerning the contents of the Report, unless required by the relevant governmental authorities, laws or court orders.. The Company shall not be called or be liable to be called to give evidence or testimony on the Report in a court of law without its prior written consent, unless required by the relevant governmental authorities, laws or court orders. 4. The Report refers only to the sample tested and does not apply to the bulk, unless the sampling has been carried out by the Company and is stated as such in the Report. 5. In the event of the improper use the report as determined by the Company, the Company reserves the right to withdraw it, and to adopt any other additional remedies which may be appropriate. 6. Sample submitted for testing are accepted on the understanding that the Report issued cannot form the basis of, or be the instrument for, any legal action against the Company. 7. The Company will not be liable for or accept responsibility for any loss or damage howsoever arising from the use of information contained in any of its Reports or in any communication whatsoever about its said tests or investigations. 8. Clients wishing to use the Report in court proceedings or arbitration shall inform the Company to that effect prior to submitting the sample for testing. 9. Subject to the variable length of retention time for test data and report stored hereinto as to otherwise specifically required by individual accreditation authorities, the Company will only keep the supporting test data and information of this test report for a period of three years. The data and information will be disposed of after the aforementioned retention period has elapsed. Under no circumstances shall we provide any data and information which has been disposed of after the retention period. Under no circumstances shall we be liable for damages of any kind, including (but not limited to) compensatory damages, lost profits, lost data, or any form of special, incidental, indirect, consequential or punitive damages of any kind, whether based on breach of contract of warranty, tort (including negligence), product liability or otherwise, even if we are informed in advance of the possibility of such damages. 10. Issuance records of the Report are available on the internet at Further enquiry of validity or verification of the Reports should be addressed to the Company.