B65 LED Emergency lighting units with LEDs

Transcription

1 65 LED Page Standard: /33/34/40 ddressable LVS: 1. Description Installation Operation onnection ddressing an LVS luminaire with the configuration tool Photometric data Maintenance ompliance and approvals ccessories DESRIPTION IP 65 - IK 07 emergency luminaires with LEDs lass II: 0 at. No. Flux/ standby STD/ LVS Mode M cons. NM cons. Type of battery Im/1 hr STD M/NM 4 2 Nid Im/1 hr STD M/NM 4 2 Nid Im/1 hr STD M/NM 4 2 Nid Im/3 hrs STD M/NM NiMH Im/1 hr LVS M/NM 4 2 Nid Im/1 hr LVS M/NM Nid Im/1 hr LVS M/NM NiMH Im/3 hrs LVS M/NM NiMH Delivery Dimensions DESRIPTION (ONTINUED) 280 Weight of product in packaging: 700 grammes Volume of product in packaging: 2.3 dm Technical characteristics 230 V± - 50/60 Hz power supply Fitted with large capacity automatic connection terminals (2 x 2.5 mm 2 ) lass II: 0 Operating temperature: 0 to +40. Remote control for setting to rest state during intentional mains power breaks. Remote control input terminals protected against errors of connection. Terminal used to switch the maintained part of the light on and off in M/ NM units. omplies with standards: EN warded the ENE EN and ENOR quality mark Product for surface mounting on walls or ceilings. 1/9

2 10 max 65 LED 1. DESRIPTION (ONTINUED) 2. INSTLLTION (ONTINUED) Materials Fixing 200 mm Min Ø 16/20/25 mm 7 max Diffuser: self-extinguishing opal polycarbonate s Reflector: self-extinguishing white polycarbonate s Electronic board attery Terminal support plate: polypropylene self-extinguishing s Removable base: polypropylene self-extinguishing s ll plastic parts weighing more than 50 g are marked with their material type so that the materials can be recycled at the end of the life of the product. 2. INSTLLTION Opening the unit Wiring able entry REMOTE ONTROL - onnection terminals: no polarity with the Legrand remote control at. No /01. Terminal capacity: 2 x 2.5 mm 2. If wiring with flexible wires able entry able entry 12 mm 2/9

3 65 LED 2. INSTLLTION (ONTINUED) 3. OPERTION (ONTINUED) Wiring in maintained mode Lighting switch L N 230 V Wiring in non-maintained mode L N 230 V Lighting main L N 1.5/2.5 mm mm 12 L Lighting main 3.3 Setting to rest state via the remote control at. No /01 fter the normal lighting is switched off intentionally: Pressing the button sets the unit to rest state to prevent the battery discharging. Normal lighting switched back on: The luminaire automatically returns to standby in the initial operating mode (M/NM). 3.4 Testing standard luminaires Standard luminaires can be tested by a normal power break: - switch-on is verified correctly when the emergency LEDs are on - standby power is verified correctly when the emergency LEDs stay on throughout the rated standby power time (1 or 3 hours). 3.5 Testing LVS luminaires LVS luminaires incorporate two operating modes: Self-test mode and addressable mode. Self-test mode LVS luminaires are factory-configured in Self-test mode, and can therefore be used in this mode without requiring any change of setting. ddressable mode This luminaire can also be used on an addressable system. For this it must be addressed using the infrared configuration tool at. No in accordance with the procedure described in section 6. It then becomes possible to control it remotely using the control interface at. No (for more detailed information, see the addressable luminaires installation manual supplied with at. No ). 3. OPERTION 3.1 Switch-on/standby state Maintained The emergency LEDs come on (flux -100 lumens) if terminal L' is powered Luminaire green status LED on Non-maintained The emergency LEDs are off Luminaire green status LED on 3.2 Mains supply break/emergency operation Maintained The emergency LEDs come on at rated flux Luminaire green status LED goes off Non-maintained The emergency LEDs come on at rated flux Luminaire green status LED goes off utomatic checking of the luminaire status (Self-test system) This luminaire automatically checks its operating status. This operating mode is only available for LVS luminaires. Once a week: Switches to emergency state for 15 seconds and tests switching to emergency operation and the light sources. Once every three months: Switches to emergency operation for the rated standby power time (1 hr; 3 hrs) and tests the battery standby power Result of the automatic checks LEDs Green Yellow Luminaire OK (steady or flashing) attery fault (steady) Other fault(s) (rapid flashing) The time of the tests is set at the time the luminaire is first switched on. The day of the test is chosen randomly in order to ensure that a minimum number of luminaires is tested at the same time. The time at which all the luminaires are tested can be changed to the required time by simultaneously pressing the and buttons on the remote control Stopping a test in progress If a standby power test hinders operation, it can be stopped immediately. Press the OFF button on the remote control unit at. No or on the control interface at. No The test is stopped and postponed until the following day. 3/9

4 230 V 50 Hz 15 m 65 LED 3. OPERTION (ONTINUED) Special cases When the luminaire has been switched off for more than 3 days, the tests are no longer carried out. The test cycle will resume after the luminaire is switched back on and the batteries have been recharged. The tests planned for the day the luminaire is switched back on are automatically postponed for 24 hours. 4. ONNETION (ONTINUED) 4.2 onnecting the remote control Remote control for setting to rest state at. No ONNETION 4.1 onnecting the mains power to the self-contained luminaires The branch can be joined in the electric cabinet, on the switch or in a junction box. The power supply to the luminaires is subject to the same rules as the luminaires (normal wiring). Lighting main Reinforced emergency light Remote control Lighting The polarity of the remote control need not be followed on LVS luminaires if a Legrand remote control at. No or is used. If another remote control is used, the polarity must be followed when wiring, and the switch-on or switch-off command must be maintained for at least 2 seconds. Normal lighting switch Luminaires with LEDs Luminaires with LEDs 4/9

5 65 LED 4. ONNETION (ONTINUED) 4.3 onnection for an addressable installation for LVS luminaires (at. Nos. only) Installation with general setting to rest state V mains supply Max. length of a line of luminaires: 700 m. bove this length, place a repeater in series with the following luminaires (4 repeaters max. cascaded) ontrol interface at. No Repeater at. No luminaires and 2500 m of cable (1.5 mm 2 max.) directly connected to the control interface. bove this use a repeater 1023 luminaires max. Repeater at. No Installation with partial setting to rest state 1 to 250 luminaires ommon areas: corridors, stairways, etc. Floor V mains supply 1 to 250 luminaires 10 circuit breaker ontrol interface Floor 1 1, 2: ontrol units for setting the establishment partly to rest mode. These control units have no effect on the other parts of the installation. ommon areas: entrance to the building, etc. 5/9

6 65 LED 5. DDRESSING N LVS LUMINIRE WITH THE ONFIGURTION TOOL T. NO DDRESSING N LVS LUMINIRE WITH THE ONFIGURTION TOOL T. NO Programming the address with the configuration tool loaded using the interface configuration software Turn on the configuration tool by pressing OK for 2 seconds. ET1 (000/011) ET2 (000/021) RD (000/012) ET1 (000/025) Zones dresses Test adressage Langue Select the Zones line in the main menu Indicates the number of luminaires in the zone and how many are addressed: here there are 11 luminaires in this zone and 0 addressed. ZONES ET1-001 ET2-002 RD -003 ET1-004 Explanation of the buttons: Used to give the switch position for switched luminaires. The luminaire must be powered up. Used to address the luminaire by standing under it with the configuration tool (the luminaire emergency LEDs come on for 2 seconds). The luminaire must not already have an address. Used to delete addressing in a luminaire with this address. ddress 0000 is used to delete addressing regardless of the unit address (the emergency LEDs come on twice for 2 seconds). This step is essential when changing the luminaire address. Used to test the addressed luminaire (the luminaire emergency LEDs come on for 2 seconds to signal that the luminaire contains the unit address and the standby LEDs go off to signal that the luminaire does not have the right address). The luminaire has registered the address, so its emergency LEDs come on for 2 seconds. Select the zone in which you wish to address the luminaires. Max. distance between remote control and luminaire of 0.1 to 2 m. 6/9

7 65 LED 5. DDRESSING N LVS LUMINIRE WITH THE ONFIGURTION TOOL T. NO Programming a known address with the configuration tool For example address Zones dresses Test adressage Langue DRESSES 5. DDRESSING N LVS LUMINIRE WITH THE ONFIGURTION TOOL T. NO Testing a particular address ZONES ET1-001 ET2-002 RD -003 ET1-004 DRESSES DRESSES If the address in the luminaire is the address being tested, its emergency LEDs come on for 2 seconds. If the luminaire has another address or no address, the luminaire switches off its LED indicator. 5.4 Testing whether the luminaire is addressed DRESSES Explanation of the buttons: Used to address the luminaire by standing under it with the configuration tool (the luminaire emergency LEDs come on for 2 seconds). The luminaire must not already have an address. Zones dresses Test adressage Langue Used to delete addressing in the luminaire with this address. ddress 0000 is used to delete addressing regardless of the unit address (the emergency LEDs come on twice for 2 seconds). This step is essential when changing the luminaire address. Used to test the addressed luminaire (the luminaire emergency LEDs come on for 2 seconds to signal that the luminaire contains the unit address and the standby LEDs go off to signal that the luminaire does not have the right address). Max. distance between remote control and luminaire of 0.1 to 2 m. The luminaire has registered the address, so its emergency LEDs come on for 2 seconds. Max. distance between remote control and luminaire of 0.1 to 2 m. The luminaire has an address, so its emergency LEDs come on for 2 seconds. The luminaire does not have an address, so it switches off its LED indicator. 7/9

8 65 LED 5. DDRESSING LUMINIRE WITH THE ONFIGURTION TOOL T. NO (ONTINUED) 7. MINTENNE (ONTINUED) 5.5 Deleting the address of a unit ZONES ET1-001 ET2-002 RD -003 ET Replacing the batteries The batteries must be replaced when the self-contained luminaire no longer works for its rated operating time. aution: this product must be switched off before dismantling. I 0 OFF The operation is registered, the standby LEDs remain on and the emergency LEDs come on twice. Max. distance between remote control and luminaire of 0.1 to 2 m. 6. PHOTOMETRI DT The photometric data for all these luminaires are available in the Legrand Dialux plug-in which can be obtained from the Legrand website. 7. MINTENNE 7.1 Spare parts Luminaire at. No. attery Spare battery at. No V 1.5 h Nid / V 1.5 h Nid / V 1.5 h Nid / / V 2 h NiMH ON N: The LEDs cannot be replaced Legrand distribution partners take back used luminaires and batteries. When the batteries have been changed, replace the maintenance label, marking on it the date on which the luminaire is returned to service. I 0 8/9

9 LED 8. OMPLINE ND PPROVLS EN : European standard Luminaires: specific rules. Luminaires for emergency lighting EN : European standard Luminaires EN 50172: European standard Emergency escape lighting systems EN 1838: European standard Lighting applications Emergency lighting Products certified to the ENOR N quality mark Electromagnetic effects: EM Emission - EN (disturbance voltages) - EN (measurement of harmonics) class - EN (radiated interference) class Immunity - EN (electrostatic discharges) criterion 4 kv (contact) - EN (radiated fields) criterion 10 V/m - EN (fast transients/bursts) criterion 4 kv on network and 1 kv by coupling - EN (lightning impulses) criterion - EN (conducted disturbances) criterion - EN (magnetic fields) criterion - EN (voltage dips and short interruptions) 9. ESSORIES Self-adhesive legend plates - onforming to standard EN ISO 7010: Other suggested solutions: EXIT UITGNG SLID SLID DE EMERGENI IRTEER SORTID SORTIE SĺD NO EXIT SIN SLID /9