Solutions Solutions for a modern by information Nestor Cables society

Transcription

1 Solutions Solutions for a modern by information Nestor Cables society 1

2 From cable manufacturer to solution provider During past years Nestor Cables has changed from a traditional cable manufacturer into a modern solution provider - nowadays we aim to deliver complete solution packages to meet our customers needs. Our solutions have been developed with decades of experience in cable technologies and in close cooperation with our customers. In this brochure we introduce some of our solutions: Fibre to the Antenna, Fibre to the Home, Fibre Optic Cables in Windmill Farms, Mobile Optical Cable Units, Nestor Cables Security System N-Sec and Microduct cabling solution. Contents To learn more about our products and company, or to read news and announcements about our recent projects and presence in industry events, please visit our website. FTTA - Fibre to the Antenna 3 FTTH - Fibre to the Home 7 Fibre Optic Cables in Windmill Farms 19 Mobile Optical Cable Units 22 Nestor Cables Security System N-Sec 27 Microduct Cabling Solution 31 2 Our factory in Oulu was taken into use in 2008 and it is one of the most modern cable factories in its size group in Europe.

3 FTTA - Fibre to the Antenna Nestor Cables new FTTA - Fibre to the Antenna Solution with no need for junction box is based on: connectorized main feeder cable watertight IP-LC connectors separate jumper cables to RRU s The main feeder cable has alternatively 6, 12 or 24 fibres and the length can be specified by the customer from 20 to 150 m. The jumper cables with two singlemode fibres are supplied from one end with IP-LC connectors that will be connected with IP-LC adapters to the connectors of the main feeder cable. The other ends of the jumper cables are supplied with the connectors that are compatible with the interfaces of RRU s like LC Duplex or FULL AXS connectors. The standard length of the jumper cables is 3 m but other lengths are also available. 3

4 FTTA main feeder cable The type of the main feeder cable is non-metallic indoor/ outdoor cable FYORMU made by Nestor Cables Ltd. The construction of the cable is central tube type consisting one plastic tube containing 6, 12 or 24 primary coated fibres that are loosely inside the tube. The central tube construction gives very high crush strength. The sufficient tensile strength is achieved with the glass yarn armouring between the central tube and the cable sheath. The main feeder cable with 12 fibres, length 30 m 4 The properties of FYORMU: Diameter 7,4 mm Weight 45 kg/km Minimum bending radius During 150 mm installation Installed 75 mm Max. tension 1000 N Crush strength 2000 N Temperature range Installation C Operation C Termination of the cable The main feeder cable is supplied with connectorized tails. The upper end of the cable is terminated to short duplex fibre tails with IP-LC connectors. The lower end of the cable is supplied with single fibre tails with LC/ UPC connectors. These tails are reinforced with aramide yarns and the outer diameter of these tails is 2,0 mm. The lengths of these tails are stepped with pairs and the maximum length of these tails can be specified by the customer from 1 m to 3 m. All these tails are protected with a flexible protection tube that can be used also as a pulling end.

5 IP-LC connector IP-LC connector is designed to exceed the requirements of ODVA. The connectors meet IP 68 environmental sealing ratings and are the ideal choice for low cost/easy to use solutions in any harsh environment applications. IP-LC connector is designed according to the IEC interface standard which allows mating to any similar mechanical locking systems. Connection between the main feeder cable and the jumper cable (Above) IP-LC connector (Senko); (below) Fixed IP-LC connector adapter at the end of the pigtail of the riser cable (Senko) FTTA jumper cable Flexible jumper cables have two single-mode fibres that are terminated from the other end with IP-LC connectors and from the other end with the connectors that are compatible with the connectors of RRU units like LC Duplex or FULL AXS connectors. The standard length of the jumper cables is 3 m but the lengths can be specified by the customer. FTTA jumper cable with IP-LC and LC Duplex connectors 5

6 The connection of the main feeder cable to active equipment in the base station The type of the main feeder cable is non-metallic indoor/outdoor cable FYORMU made by Nestor Cables Ltd. The construction of the cable is central tube type consisting one plastic tube containing 6, 12 or 24 primary coated fibres that are loosely inside the tube. The central tube construction gives very high crush strength. The sufficient tensile strength is achieved with the glass yarn armouring between the central tube and the cable sheath. Patch panel NC-232 LC-D, height 1U The connectors of the lower end of the main feeder cable are directly mounted to active equipment 6

7 FTTH - Fibre to the Home Building Fibre to the Home (FTTH) networks deviates from the general construction of trunk line fibre optic cable routes. Differences are caused by large amounts of fibre, many branchings, and bringing fibre optic cables all the way to homes. Technically viable, long-term and cost-effective solutions in network materials, cables and installation accessories are constantly being sought when building FTTH networks. In our solutions, we use familiar trunk line materials as a starting point. With the advantage of our long-term experience, we have developed cable and accessory solutions specifically designed for Fibre to the Home networks. Since the number of subscribers may grow rapidly from a few dozen to even thousands, it is important to plan the construction and material solutions for networks and material solutions so that the networks can be maintained and expanded in a controlled manner over the years. Products needed for FTTH networks are for example: Cables for different FTTH layers Installation accessories Connection products 7

8 Fibre optic cables Different parts of FTTH network need different kinds of cables. Nestor Cables product range contains suitable cables for these FTTH layers: feeder cables, distribution cables and drop cables. secondary distributor drop cables access node feeder cable(s) primary distributor distribution cables distribution cables secondary distributor drop cables drop cables secondary distributor Fibre optic cables Fibre connections are becoming continuously more common and contain almost unlimited possibilities for Internet, speech and TV services within the same subscriber line. Services in health and well-being, safety, remote work, education and entertainment, high-definition TV and express messaging fibre optics represent the only solution which can reliably meet the needs of households in the future. 8 subscribers Nestor Cables comprehensive range of optical fibre cables offers dependable solutions for various installation conditions and to meet special requirements. Examples of our fibre optic cable range are listed on the right side page and are divided by installation methods.

9 FYOVD2PMU FZOVDMU-SD FZOMSU-SD FYOHBMUK FTMS Direct buried cables FYOVD2PMU (6, 12, 24, 48 and 96 fibres) FZOMVDMU-SD (24, 48, 96 and 192 fibres) FZOVDMU-SD (288, 384 and 432 fibres) Direct buried and duct cables FZVD2PMU Flex (24, 48, 96, 192 and 288 fibres) FZ4RMU Flex (fibres 24, 48, 96 and 192) Duct cables FYO2RMU (6, 12, 24, 48 and 96 fibres) FZOHBMU-SD (standard 24, 48, 96 and 192 fibres, max. 432 fibres) Microduct cables FYORMU Micro (4, 6 and 12 fibres) FZOMU-SD Micro (12, 24, 48, 72 and 96 fibres) Buried drop cables FYO2PMU Mini (4, 6 and 12 fibres) FYO2RMU 3,5 kn (4, 6 and 12 fibres) Aerial cables FYOHBMUK (6, 12, 24, 48 and 96 fibres) Non-metallic aerial cables - ADSS FYORMU (4, 6 and 12 fibres) FZORMU-SD (24, 48, 72 and 96 fibres) Indoor/outdoor cables FZOMSU-SD (6, 12, 24, 48, 96 and 192 fibres) FZ2RMSU Flex (12, 24, 48, 96 and 192 fibres) Indoor cables FTMS (4 and 12 fibres) FY2RMS/ FY2RMS Flex (12 or 24 fibres/ 24, 36, 48, 60, 72, 96 or 144 fibres) 9

10 Installation accessories In addition to cables for FTTH applications, Nestor Cables product range includes variety of installation accessories for FTTH networks. Product range contain ODF solutions, joint closures and splice cabinets and termination solutions. ODF and active equipment joint closure or splice cabinet joint closure or splice cabinet building distributor equipment room primary distributor secondary distributor subscriber 10

11 Products for equipment rooms In FTTH applications following products are needed in equipment rooms: ODF frames and modules with accessories Indoor splice cabinets Patch cords and jumper cables Splitter modules for PON networks Fibre trays ODF system NC-1000 ODF system NC-1000 is modular and high capacity cross-connection system for large cross-connections and for FTTH applications. Dimension 600x300x2000 and 600x300x2200 mm Capacity for up to 2016 fibres All splices will be done outside of the frame NC-1000 patch panels: Pre-assembled NC-1000 patch panels with SC/APC and LC/APC connectors with indoor/ outdoor cable FZOMSU-SD Mini ((length m, fibre quantity 48) Space for storing and handling patch cords Storage for patch cords and a gateway to other ODF frames ODF system NC-2200 ODF system NC-2200 is similar modular and high capacity cross-connection system for large cross-connections and for FTTH applications but based on 19 mechanics. Dimension 900x300x2200 Capacity for up to 3840 fibres Pre-assembled NC-232 patch panels with SC/APC and LC/ APC connectors and with indoor/outdoor cable FZOMSU-SD Mini (length m, fibre quantity 48 or 96) Space for storing and handling patch cords ODF system NC-1000 and ODF system NC

12 NC-2000 connection system Connection cabinet NC-2000 Designed specially for FTTX applications Based on 19 mechanics Gives possibility to place fibre terminations and active equipment to the same cabinet Dimensions W800 x S600 xh2000 mm and W800 x S800 xh2000 mm Supplied with accessories for handling big number of fibres in terminations and in connections The ventilation of the air inside of the cabinets is taken care with the holed doors in both sides of the cabinets Products NC-2000 connection cabinets Pre-assembled NC-232 patch panels NC-2000 splice tray holders with splice trays Accessories for guiding patch cords Cable guides Guiding hooks Guiding panels Storage shelf 12

13 Splice cabinets for indoor use Indoor splice cabinet NC-115 Space for 24 splices Supplied with an adapter plate for 12 SC-D adapters Indoor splice cabinet NC-300 For wall installations Space for 4 splice trays (192 splices) Splice cabinet NC-330 Capacity for 960 splices Can be stacked over each other Splice cabinets NC-1000 Capacity for 3456 splices 13

14 Splicing products for outdoor use NC-400 Universal joint closure (Pre-assembled kits for 48, 96, 192 and for 288 fibres) Universal joint closure for FO networks Capacity for 288 fibres Delivered as a pre-assebled kit for 48, 96, 192 and for 288 fibres One oval and six Ø 23 mm cable inlets Joint closures, NC-400 product family Can be installed directly to the ground, manhole, handhole, street cabinet and to the pole Material acid-proof stainless steel For fibre quantities pcs Products: NC-412 Drop cable closure 1 cable inlet for 2 or 3 drop cable Capacity for 12 fibre splices NC F and NC F Joint closures for FTTX networks (alternative version v.2 for trunk networks) Basic versions have inlets for 2 trunk cables and for 4/7 inlets for drop cables In version 2 part of the inlets for drop cables have been replaced with bigger inlets for trunk cables 14 NC-412 drop cable closure and NC F joint closure v.2

15 Integrated splice cabinet NC-360 NC-350 Splice cabinets for outdoor use, NC-300 product family For fibre quantities pcs Can be supplied with patch panels and splitter modules Products: NC-300 Splice cabinet for up to 192 fibres Dimension W300 x H400 x D132 mm Installation inside of another cabinet NC-320 Splice cabinet for up to 480 fibres Dimensions W360 x H648 x D194 mm Installation inside of another cabinet NC-352 Integrated scross-connection cabinet including cross-connection cabinet NC-350 and a street cabinet with a base Dimensions W850 x H2200 x D360 mm NC-360 Integrated splice cabinet including splice cabinet NC-320 and a street cabinet with a base Dimensions W850 x H2200 x D360 mm Cross-connection cabinets for outdoor use, NC-300 product family Products: NC-315 For 480 splices and space for up to 48 SC or 96 LC connectors Slim NC-YJT patch panels for 12 or 24 fibres Dimension W490 x H670 x D270 mm Is installed inside of another cabinet NC-350 Integrated splice cabinet including a splice module for 48 fibres and a street cabinet with a fixed base Dimensions W400 x D210 x H700 mm NC-350 Based on 19 mechanics Gives 12 U space for patch panels, splice modules and splitter modules Dimensions W740 x H980 x D275 mm 15

16 Termination products Termination boxes for wall installations Termination box NC-125 For drop cable with metallic elements For 4 fibres Termination box NC-127 For non-metallic drop cable For 4 fibres Termination box NC-110 Universal termination box For 24 fibres The termination of the drop cable in the countryside Outdoor termination box NC-140 Tightness IP 54 Dimensions W125 x H175 x D 75 mm Can be supplied with an adapter plate for 2 SC or LC-D adapters Pre-terminated FTTH outlet NC-105 Is supplied with a small, non-metallic, flexible, flame-retardant and zero-halogen indoor/outdoor cable The cable has two G.657.A1 fibres The cable is pre-terminated top the outlet with SC/UPC. SC/APC, LC/UPC or with LC/APC connectors Standard length 30 m (Above) Termination box NC-125; (below) Outdoor termination box NC-140 and pre-terminated FTTH outlet NC

17 (Above) Patch panel NC-200; (below) Pre-assembled patch panel NC-232 as a pigtail cable kit for 96 fibres Patch panels for 19 racks and cabinets Patch panel NC-200 For up to 48 fibres Size: 430 (19 ) x 230 x 44 (1 U) mm Supplied with a gliding inner part that works as a splice tray Patch panel NC-232 For up to 48 fibres Size: 430 (19 ) x 140 x 44 (1 U) mm Supplied with guiding hooks and a removable protection plate for patch cords Pre-assembled patch panel NC-200 Pigtail kit NC-200 Supplied with pre-assembled pigtails and adapters Available for fibre quantities 12, 24 and 48 pcs Connector alternatives SC/UPC, SC/APC, LC/UPC and LC/APC Pigtail cable kit NC-200 Supplied with pre-assembled pigtail cable The cable is for indoor and outdoor use with 24 or 48 fibres Standard cable lenghts are 5, 15, 25 and 50 m but customized cable lengths are also available Pre-assembled patch panel NC-232 Pigtail kit NC-232 Supplied with pre-assembled pigtails and adapters Available for fibre quantities 12, 24 and 48 pcs Connector alternatives SC/UPC, SC/APC, LC/UPC and LC/APC Pigtail cable kit NC-232 Supplied with pre-assembled pigtail cable The cable is for indoor and outdoor use with 24 or 48 fibres Standard cable lenghts are 5, 15, 25 and 50 m but customized cable lengths are also available 17

18 Connection products Patch cords and jumper cables for equipment rooms Cables are available with the fibre quantities 1, 2, 4, 12 and 24 pcs Alternative connector types are SC/UPC, SC/APC and LC/UPC The lengths of the simplex and duplex patch cords are 2, 3, 5 and 10 m Jumper cables with 2, 4, 12 and 24 fibres are delivered as customized lenghts from 5 to 200 m Couplers and splitters FBT couplers Types 1x2 and 1x3 Available with or without connectors Can be mounted to different type of mechanics PLC splitters Types 1x2, 1x4, 1x8, 1x16, 1x32, 1x64, 2x16 and 2x32 1x64 Available with or without connectors Can be mounted to different type of mechanics Splitter modules NC-1000 and NC-2000 Available in versions 1x16, 1x32, 2x16, 2x32 and 1x64 Connector types SC/APC and LC/APC 18

19 Fibre Optic Cables in Windmill Farms Windmill farms are built nowadays all around the world for getting more and more pure energy. Today s windmills are very efficient, and windmill farms can also consist of tens or even more than 100 windmills. The use of separate windmill efficiently and safely requires reliable control systems, alternatively radio links or fibre optic cables. Both alternatives have their own benefits but fibre optic cables are used often because of their excellent features like being immune against all kinds of disturbances. Nestor Cables has delivered fibre optic cables and accessories to many windmill farms in Finland. Based on these experiences Nestor Cables has developed an own cabling concept for windmill farms consisting of all the materials for fibre optic cablings both for small and large windmill farms. Since the control systems are just a small part in these kind of large projects, the cabling concept includes as few products as possible. The main products are as follows: Fibre optic cables Splice cabinets Termination boxes to windmills Patch panels and connection cabinets to power station 19

20 Fibre optic cables Fibre optic cables are generally installed to the same canal and to the road bank as power cables. Thus the cables shall be non-metallic and also rugged enough to be installed directly into the ground. For that purpose Nestor Cables has two cable types: one with 4 12 optical fibres and the other with fibres. 20 Non-metallic buried cables FYO2RMU 3,5 kn and FZ4RMU Flex 3,5 kn Splice cabinet NC-360A with the inner cabinet Splice cabinets The simplest way in cablings is to install optical cables directly from the power station to each windmill but quite often, and especially in large windmill farms, the cabling is ensured with two cables to each windmills. These two cables can be taken directly to windmills but very often these cables are terminated to splice cabinet outside the windmills and two alternative cables goes from the splice cabinet to the windmill.

21 Termination boxes to windmills The termination boxes have to be tight because the humidity level inside the windmills can be very high and additionally the boxes need to have enough capacity for terminating up to 24 fibres. Nestor Cables new NC-135A termination box meets all these requirements. (Left side) Termination box for windmills NC-135A and a preassembled patch panel NC-232; (right side) Connection cabinet NC-2000 Patch panels and connection cabinets to power station In power stations fibre optic cables are typically terminated to normal 19 patch panels, mounted to connection cabinets with active equipment. For this purpose Nestor has developed own products: connection cabinet NC-2000 and pre-assembled patch panels NC-232 with 12, 24 or 48 fibres. The construction of the NC-2000 cabinet includes e.g. clear pathways for incoming cables to patch panels and enough space with guides for controlling even a big number of patch cords. Nestor s patch panel is easy to install and it can be mounted directly on top of each other. For protecting patch cords the panel has cable guides with a removable protection plate. 21

22 Mobile Optical Cable Units Several military applications utilize tactical fibre optic cables to create temporary mobile cable networks. Nestor Cables has offered mobile optical cable unit solutions for military purposes already for years but now these solutions have been modified to suit civilian everyday events and are available to all our customers. Different kind of public events often demand temporary fibre optic cable connections. Such events could be for example sports events, exhibitions and music festivals. Also crisis situations can create a sudden need for quickly installed telecommunication networks. These solutions have proved their stability and functionality in harsh military conditions. Solutions mainly consist of the following products: Connectorized cable units Special reels Carrying frames Reeling and unreeling equipment Connection boxes 22

23 Special cables for mobile optical cable units Tactical cable FTMRMU 2 x SM/MM FTMRMU was originally developed as a tactical cable for military applications. It includes two singlemode or multimode fibres. Outer diameter 4,6 mm Weight 17 kg/km Max. tension during installation 700 N Max. crush strength with 100 mm plate 1500 N Operating temperature C Indoor/outdoor cable FTRMSU 2/4 x SM FTRMSU is a special cable that has been developed from the tactical fibre optic cable. It includes 2 or 4 singlemode fibres (G.657.A1). Outer diameter 4,6 mm Weight 17 kg/km Max. tension during installation 500 N Max. crush strength with 100 mm plate 1500 N Operating temperature C Reels 1-hand reel Dimensions: W410 x H450 x D240 mm Weight (without cable): 3,4 kg Material: Powder painted aluminium Max. cable length 300 m Small reel Dimensions: Ø 370 mm x 430 mm Weight (without cable): 2,9 kg Material: Powder painted stainless steel Max. cable length 800 m Small reel Indoor/outdoor cable FTRMSU 4 x SM Big reel Dimensions: Ø 560 mm x 670 mm Weight (without cable): 23,5 kg Material: Powder painted stainless steel Max. cable length 3000 m 23

24 Connectors Exbanded-beam connector Pro Beam Jr. (J2SP) Tightness IP 67 With the help of the lenses this connector is not so sensitive against dust as a normal ferrule connector Insertion loss 1,5 db Connection directly against each other IP-LC connector Tightness IP 67 Includes one LC Duplex connector Bayonet type locking SC/UPC and SC/APC connector For connections to active equipment The fibres are protected with aramid re-inforced protection tubes between the cable sheath and connectors LC Duplex connector (LC-D) For connections to active equipment Suits directly to tactical cable and to 2F FTRMSU special cable IP-LC adapters IP-LC connector IP-LC In-Line Adapter for cable connections Supplied with a tight protection cab. IP-LC Bulkhead Adapter for connection boxes and patch panels Inside the boxes normal pigtails and patchcords can be mounted to this adapter. Adapter is supplied with a nut, sealing ring and a tight protection cab for the cable side. 24 IP-LC In-Line Adapter IP-LC Bulkhead Adapter

25 2F patch cords Products: J2SP J2SP SM FTMRMU J2SP LC-D SM FTMRMU IP-LC IP-LC, SM FTMRMU IP-LC LC-D, SM FTMRMU LC-D LC-DSM FTMRMU The lengths of patch cords are 2, 5 and 10 m. Customized lengths available. Patchcord Mobile optical cable units Products: J2SP J2SP 2xSM FTMRMU Lengths 200 m, 400 m, 800 m, 3000 m IP-LC IP-LC 2xSM FTMRMU Lengths 100 m, 200 m, 300 m LC-D LC-D 2xSM FTMRMU Lengths 100 m, 200 m, 300 m Customized lengths available. SC/UPC SC/UPC 4xSM FTMRMU Lengths 100 m, 200 m, 300 m SC/APC SC/APC4xSM FTMRMU Lengths 100 m, 200 m, 300 m LC/UPC LC/UPC 4xSM FTMRMU Lenghts 100 m, 200 m, 300 m LC/APC LC/APC 4xSM FTMRMU Lengths 100 m, 200 m, 300 m Customized lengths available. The connectorized cable ends are protected with flexible protection tubes that can be used also as pulling heads. Connection boxes with IP- LC connectors Connection box NC-140 IP-LC in use NC-135A IP-LC Size 300 x 300 x 132 mm Tightness IP 67 3 cable inlets For splicing up to 24 fibres Places for eight IP-LC connector adapters NC-140 IP-LC Size 175 x 125 x 75 mm Tightness IP 67 3 cable inlets For splicing up to 6 fibres Places for three IP-LC connector adapters 25

26 Accessories for reels Reeling and unreeling equipment for big reels Nestor Cables reeling and unreeling equipment can be mounted on different types of vehicles. It operates with gasoline E95/95E10 and E98. Equipment is supplied with a control panel and an adjustable rod for guiding the cable. Other accessories Cleaning kit for fibre optic connectors 26 Carrying frame for small reels Carrying frame makes transporting reels easier by foot for example in forests. There are also a cable stand and a crank available for small reels. Launch fibre package for OTDR measurements

27 Nestor Cables Security System N-Sec Demand for smart systems to secure buildings, valuable items and strategic targets, and more importantly to protect people has risen in recent years. N-Sec by Nestor Cables is a versatile and reliable security system which can be tailored to suit each customer s needs and requirements. This proven system is based on Nestor Cables fibre optic technology and FOSS TM intelligent hardware and software by Multitec Finland. 27

28 N-Sec by Nestor Cables is... Suitable for varying conditions Cable can stand wide temperature range of -45 to +100 C FOSS unit is rated from -40 to +50 C (Installation into man holes is necessary in hot conditions) Insensitive to the high-voltage field, magnetic field and radio field Insensitive to different weather conditions: lightning, hard rain, mist Suitable to be used together with explosives and gases Invisible non-metallic optical sensor cables Solutions for indoor and outdoor uses Sensitivity can be adjusted to the needed level Doesn t react to small animals Fence cable doesn t react to persons or vehicles if there isn t physical contact. Quick and easy to install and implement Direct buried installations are possible Installation can be fixed or temporary Customizable Different cable types for different purposes Cables which are used as sensors can be hidden or visible. Cable lengths and controlled targets can vary Additional equipment (Cameras, lights, sound and movement detectors) can be attached to the system 28 Examples of solutions Buried N-Sec solution Hidden and very precise system utilizing buried cables which are installed directly below the tiles. N-Sec Road sensor optical cables Solution based on optical non-metallic cables which are buried cm below the surface. Sensor cable can make several paths under the road or pathway. Special cushion can be used to avoid disturbances. N-Sec Fence sensor optical cables Solution based on sensor optical cablesis ideal to secure fences and walls: system prevents for example climbing over barriers to break into secured area. N-Sec sensor optical cables for indoor use Sensor optical cables can be used for protection of single targets or entire rooms. Cables are installed under flooring or under single covers. Temporary installations are possible.

29 Main components of the system N-Sec Sensor Cable Sensor cable is always an optical cable 0,9 mm cable for specific indoor installations 4 mm cable for fences 12 mm cable for buried solutions where the soil is static Cables can be designed according to target s requirements Non-metallic sensor cables are suitable for demanding conditions like explosive storages Can not be found by metal detectors when buried. Sensor cable is connected to FOSS unit FOSS Unit by Multitec Finland Small robust system, which acts as an intelligent part of the system sends and receives light FOSS is connected to PC and all settings can be controlled and adjusted easily by user FOSS TM unit is operated by dedicated software Senses even minor changes in the fibers Level of the accuracy can be adjusted Sends alarm message forward The unit has good references and it is made and developed by Multitec Finland N-Sec Connection and Energy Supply Cable FOSS unit needs energy and at the same time collected data must be sent to the remote control center (to the computer). All this is secured with fiber optic copper hybrid cable. One cable is used for both essential tasks Connection and energy supply cable can be used for cameras too Supply cable is robust direct buried cable designed for this system N-Sec Remote Control Center Several sensor cables/foss units are connected via supply cables to the control center. Center is equipped with power supply and FOSS units are fed from control center using supply cable. All information goes through the center. Control center is monitoring base of different areas. Alarms are received to the control center Alarms can be forwarded from the control centers. 29

30 N-Sec Auxiliary Equipment Additionally FOSS units need protection from environment different kind of buried man holes and protection closures are available. Active components send information between FOSS and computer. All needed components are available. Direct buried stainless steel cable joint closures are available. Optional components Cameras Lights / spot lights Sound and movement sensors N-Sec is expandable system and options can be added beforehand 30

31 Microduct Cabling Solution Installing telecommunication and access network cabling in metropolitan and suburban areas can be demanding. In this kind of areas space is limited and cabling should be done underground or on existing infrastructure. These limitations can be overcome by Microduct Cabling Solution of Nestor Cables. Microcabling system is built directly to the ground or on duct routes. Access and metropolitan network infrastructure is widely built by laying duct systems underground (aerial duct solutions are also available) which then can be utilized to answer various customer needs. Microcabling system allows flexible expansion of the network. After microducts are installed, microduct cables can be easily blown in microducts whether building a new network or expanding existing network. By using microduct technology CAPEX and OPEX can be significantly reduced. Microduct cabling solution consists of: Fibre optic cables NesDuct microducts Connection accessories 31

32 Why microduct cabling solution? High fiber density of low weight microduct cables combined with ease of handling these cables, increased jetting speeds and improved duct and space utilization result in reduced costs. Microduct cabling solution offers versatility because wide variety of cables, ducts and accessories in different sizes and styles can be configurated in endless ways in nearly all possible cabling scenarios. Solution is perfect for growing and changing cities and neighborhoods: during the installation you don t need to know how the cable network should look like years ahead because microduct network can be altered easily afterwards. In our past projects microduct cabling solution has been proven to be a great success. Microduct Cabling Solution by Nestor Cables has been tested in several projects all around the world. Recently Nestor Cables has supplied microduct cables, ducts and accessories to various projects in Russia and Europe. Our products have been widely used in changing conditions (from warm summers to freezing winters) in Northern Finland for years, so we can assure that our products can withstand even extreme climate and conditions. 32 Photographs show installation of microduct cables in our recent projects.

33 Microduct cables High quality microduct cables tailored to fit your needs Space can be saved when using microcabling system. E.g. when installing microducts in existing duct system more capacity can be installed. Nestor Cables has the experience and technology to develop and manufacture microduct cables with excellent quality. Examples of our microduct cables are FZOMU-SD Micro with fibres and FYORMU Micro with 2-12 fibres. There is also remarkably smaller version of FYORMU Micro with only 2,5 mm diameter and 5 kg/km weight. FZORMU-SD 96 fibre Outer diameter 10,7 mm FZOMU-SD Micro 96 fibres Outer diameter 6,5 mm Microduct cables with flexible construction? FZOMU-SD Micro and FYORMU Micro FZOMU-SD Flex Micro is a flexible optical cable with fibres for microduct installation by blowing. Flexible construction is a new innovation in optical fibre cable technology. Benefits of the construction are flexibilty and high packing density of fibres. Nestor Cables is one of the rare cable manufacturers producing cables with this kind of construction. 33

34 Microducts for microduct cabling solution Durable ducts from a trusted supplier Ducts protect cables in ground during and after installation. Nestor Cables microduct solution includes a wide variety of NesDuct microducts to suit our customer s varied needs. Our ducts are durable and able to protect fragile fibres inside ducts from moisture, traffic and other disturbances. To offer a comprehensive variety of microducts Nestor Cables partners with carefully chosen trusted duct manufacturers. Like ourselves our partners are ISO 9001 certified and their processes are regularly audited by outside parties. NesDuct bundle NesDuct with a single microduct Nestor Cables offers mainly direct buried and direct install ducts: Direct buried installation: These ducts have impressive crush and impact resistance and therefore can be buried into the ground without other protection. Direct installation with added protection: Some ducts have thin walls and therefore they are intended for installation to places with additional mechanical protection. However these are only the most popular installation methods: to learn more about other methods, please contact us and we will assist you in finding the perfect solution. Single microducts and NesDuct bundles Nestor Cables selection of microducts consists of NesDucts with a single microduct and NesDuct bundles. Both of these include microducts for direct buried and direct installation. 34 Micro ducts are made of high quality HDPE. Nestor Cables selection of microducts has all varieties of ducts needed to create a FTTH (Fibre to The Home) or FTTX networks. Both of these are available in several sizes.

35 Accessories for microduct cabling solution Accessories to connect and secure microducts Installation and protection of a versatile microduct communications network demand ways to connect different kinds of microducts securely. Besides cables and microducts Nestor Cables also offers a selection of handy accessories to build these connections. Straight connector For jointing two microducts End stop connector For securing unused end of a microduct Gas block connector For blocking gas or moisture Reducer connector For jointing two microducts with different diameters Divisible seal Water and gas tight seal for open duct end with cable Pictures on this page only illustrate use of these accessories; actual products will differ from illustrations. 35

36 Nestor Cables product range includes almost 1000 items: optical fibre cables, copper telecommunication cables, process control and automation cables for industries, fibre optic accessories, mobile optical cable units, FTTH solutions, FTTA solutions & fibre optic cabling concept for windmill farms. To learn more about our products and company, or to read news and announcements about our recent projects and presence at industry events, please visit our website. Factory: Visiting address: Mittarikuja 5, FI Oulu, Finland Postal Address: P.O. Box 276, FI Oulu, Finland Tel Fax Office: Visiting and postal address: Äyritie 12 C, FI Vantaa, Finland Tel Fax