CM1-AD08V 0~5V, 1~5V, -10~10V, 0~10V An input signal is converted to a digital value from 0 to or from 8000 to 8000.
|
|
- Meghan Washington
- 5 years ago
- Views:
Transcription
1
2 1260 CIMON-PLC CM1-AD08V 0~5V, 1~5V, -10~10V, 0~10V An input signal is converted to a digital value from 0 to or from 8000 to Average or sampling is the method used to process input signal. As the resolution for digital value is selected as 1/16000, high-resolution digital values will be gotten. The number of the modules used for one base is not limited. Contents : General Idea Wiring Specifications Internal I/O Table Features of I/O Conversion Buffer Memory General Idea Digital Value - D
3 XP / CP Series(CM1) 1261 The value shown as number such as 0, 1, 2 and 3, and varied non-continuously is called digital value. ON signal and OFF signal are shown as the digital value of 0 and 1. BCD values and binary values are also digital values. To operate with digital values, analog values cannot be inputted directly to a CPU module. Therefore, analog values are to be converted to digital values like Picture 1.4, and to be inputted to a CPU. To output analog values, it is necessary to convert the digital values in a CPU to analog values Specifications General Specification Technical Specification Dimensions
4 1262 CIMON-PLC General Specification Item Operating Temperature Storage Temperature Operating Humidity Storage Humidity Vibration Specification -10 ~ 65 o C -25 ~ 80 o C 5 ~ 95%RH, Not condensed. 5 ~ 95%RH, Not condensed. In case of intermittent vibration Frequency Acceleration Amplitude Sweep 10 f< 57Hz mm 10 times in each 57 f < 150 Hz 9.8m/s2 {1G} - direction (X,Y,Z) In case of continuous vibration Frequency Acceleration Amplitude Sweep 10 f < 57Hz mm 10 times in each 57 f < 150 Hz 4.9m/s2 {1G} - direction (X,Y,Z) Shock - Max. Shock Acc.: 147 m/s2 {15G} Noise Environment Altitude - Time : 11 (3 times in X, Y, Z) - Pulse Wave : Half sine wave pulse Square wave impulse noise Electrostatic discharge Radiated electro-magnetic field Fast Transient Bust Noise ±1500V Voltage: 4 kv(contact discharge) 27 ~ 500 MHz. 10 V/m Item No corrosive gas and no dust. 2,000m or less Pollution Less than 2 Cooling Technical Specification Natural Air cooling Power Modul e Digital I/O (24V or more) Voltage 2KV 1KV 0.25KV Model Item CM1-AD04VI CM1-AD08V CM1-AD08I No. of Analog Input Points Analog Input 4 points 8 points 8 points 0 ~ 20mA 4 ~ 20mA 0 ~ +5V 1 ~ +5V 0 ~ +10V -10V ~ +10V Digital Output 0~16000(-8000~8000) 0 ~ +5V 1 ~ +5V 0 ~ +10V -10V ~ +10V Digital I/O(Less than 24V) Analog I/O Comm. interface 0 ~ 20mA 4 ~ 20mA
5 XP / CP Series(CM1) 1263 Maximum Resolution Input Range of Analog Input Max. Resolution Digital Output Voltage 0 ~ +5V 0.25mV 0 ~ ~ +5V mV ~ ~ +10V 0.625mV -10V ~ +10V 1.25mV Precision Current 0 ~ 20mA ±0.3%(Full Scale) 1.25mA Conversion Rate 5mS/1ch Absolute Maximum Input Voltage : ±12V Current : ±25mA ±12V ±25mA Type of Insulation Between input terminal and PLC : Photo Coupler Insulation Between Channels : No Insulation Occupied Points 16 points Contact Terminal 18-point Terminal Block Internal +5V Current +15V (ma) 0V Dimensions Unit : mm
6 1264 CIMON-PLC Features of I/O Conversion Features of I/O conversion mean the gradient of the straight line connecting offset values and gain values when the analog signals (Voltage or current) from the outside of a PLC are converted to digital values. An offset value is the analog input value(voltage or current) corresponding to the digital output value of 0(-8000) and a gain value is the analog input value(voltage or Current) corresponding to the digital output value of 16000(8000). Contents : Feature of Voltage Input (AD04VI) Feature of Voltage Input (AD08I) Feature of Voltage Input (AD08V) AD04VI No. Range of Analog Input Offset Gain Digital Output Value Max. Resolution 1 1 ~ 5V 1V 5V 0 ~ (-8000~8000) 0.25mV 2 0 ~ 5V 0V 5V mV 3 0 ~ 10V 0V 10V 0.625mV
7 XP / CP Series(CM1) ~ 10V -10V 10V 1.25mV In case that the analog inputs corresponding to the digital output values out of the range come, the maximum and the minimum of the digital output values are fixed as 192 and 16191(-8192 & 8191) AD08I No. Range of Analog Input Offset Gain Digital Output Value Max. Resolution 1 0 ~ 20mA 0mA 20mA 1.25mA 0 ~ 16000(-8000~8000) 2 4 ~ 20mA 4mA 20mA 1mA In case that the analog inputs corresponding to the digital output values out of the range come, the maximum and the minimum of the digital output values are fixed as 192 and 16191(-8192 & 8191).
8 1266 CIMON-PLC AD08V No. Range of Analog Input Offset Gain Digital Output Value Max. Resolution 1 1 ~ 5V 1V 5V 0 ~ 16000(-8000~8000) 0.25mV 2 0 ~ 5V 0V 5V mV 3 0 ~ 10V 0V 10V 0.625mV 4-10 ~ 10V -10V 10V 1.25mV In case that the analog inputs corresponding to the digital output values out of the range come, the maximum and the minimum of the digital output values are fixed as 192 and 16191(-8192 & 8191) Wiring Safety Precautions : Use separate cables for AC and outside input signals of an A/D converter module to keep from the serge
9 XP / CP Series(CM1) 1267 or the induced noise occurring from the AC. Select a wire, considering ambient temperature and allowable current. AWG22(0.3 ) or more is recommended as the thickness of the wire. Keep the wire out of heat-generating device, toxic substance and oil. They may cause breakdown or malfunction. Make sure polarity before inputting analog value to a terminal block. The wiring together with high-voltage line or power line may cause malfunction or breakdown. Contents : AD04VI AD08V AD08I AD04VI Measured values are inputted to all the channels grouped as Terminal 1-2-3, 5-6-7, and
10 1268 CIMON-PLC [ In case of voltage input ] + Terminal - Terminal Ch 1 Terminal 1 Terminal 3 Ch 2 Terminal 5 Terminal 7 Ch 3 Terminal 9 Terminal 11 Ch 4 Terminal 13 Terminal 15 [ In case of current input ] +Terminal - Terminal Action Ch 1 Terminal 2 Terminal 3 Connect 1-2 Ch 2 Terminal 6 Terminal 7 Connect 5-6 Ch 3 Terminal 10 Terminal 11 Connect 9-10 Ch 4 Terminal 14 Terminal 15 Connect V and -15V are used for AD04VI, AD08I and AD08V. POWER module is to be CM1-SPB or CM1-SPC.
11 XP / CP Series(CM1) AD08I Terminal 17 and Terminal 18 are not used. + Terminal - Terminal Ch 1 Terminal 1 Terminal 2 Ch 2 Terminal 3 Terminal 4 Ch 3 Terminal 5 Terminal 6 Ch 4 Terminal 7 Terminal 8 Ch 5 Terminal 9 Terminal 10 Ch 5 Terminal 11 Terminal 12 Ch 7 Terminal 13 Terminal 14 Ch 8 Terminal 15 Terminal 16
12 1270 CIMON-PLC AD08V Terminal 17 and Terminal 18 are not used. + Terminal - Terminal Ch 1 Terminal 1 Terminal 2 Ch 2 Terminal 3 Terminal 4 Ch 3 Terminal 5 Terminal 6 Ch 4 Terminal 7 Terminal 8 Ch 5 Terminal 9 Terminal 10 Ch 6 Terminal 11 Terminal 12 Ch 7 Terminal 13 Terminal 14 Ch 8 Terminal 15 Terminal Internal I/O Table Direction of Signal(CPU?A/D Module) Direction of Signal(CPU?A/D Module) Input Name of Signal Output Name of Signal X00 A/D module ready Y00 Not use X01 Flag indicating A/D-converted Y01 X02 Flag indicating operation condition set up Y02 Requesting to set up operation condition X03 Flag indicating the channel switched Y03 Requesting to switch an channel X04 Flag indicating offset or gain calibration mode Y04 Requesting to calibrate offset or gain X05 Not use Y05 Assigning offset or gain calibration mode X06 Y06 Not use X07 X08 X09 X0A X0B Y07 Y08 Y09 Y0A Y0B
13 XP / CP Series(CM1) 1271 X0C Y0C X0D Y0D X0E Y0E Requesting to reset max. value/min. value X0F Flag indicating an error in A/D module Y0F Requesting to clear the error The numbers of I/O signals is for the case an A/D module is mounted on Slot 0 of a local base. Contents : Input Signals Output Signals Input Signals Devic e NO. X00 X01 X02 Signal Name A/D module ready Flag indicating A/D-converted Flag indicating operation condition set up Description 1) If the power is inputted to a CPU or a CPU is reset, A/D conversion will be ready. At this time, this signal is set and A/D conversion is processed. 2) When this signal is off, A/D conversion is not processed. In the following case, A/D module ready will be reset. During Offset/Gain calibration mode If all the enabled channels convert, this signal will be set. 1) This is used as the interlock condition to set/reset request to set up operation condition(y02) when enabling/disabling to A/D-convert is switched. 2) When this signal(x02) is reset, A/D conversion is not processed. In the following case, flag indicating operation condition set up will be reset. When module ready is reset. When requesting to set up operation condition is set. X03 Flag indicating the channel 1) This is used as the interlock condition to set/reset request to switch a channel (Y03) when the channel for calibrating offset and gain is switched.
14 1272 CIMON-PLC switched 2) Refer to Chapter 7 for offset/gain calibration. X04 Flag indicating Offset or Gain calibration mode 1) This is used as the interlock condition to set/reset requesting to calibrate offset/gain(y04) when registering value after an offset/a gain are calibrated. 2) Refer to Chapter 7 for offset/gain calibration. X0F Flag indicating an error in A/D module 1) If an error occurs in writing to buffer memory, this flag will be set. 2) To clear error code, request to clear the error(y0f) is be set Output Signals Devi cen O. Y02 Signal Name Requesting to set up operation condition Description 1) This is set when the contents of enabling/disabling to A/D-convert, assigning average process, the average time and the average number of times when average process is assigned are available.
15 XP / CP Series(CM1) 1273 Y03 Y04 Y05 Y0E Y0F Requesting to switch an channel Requesting to calibrate offset or gain Assigning offset or gain mode Requesting to reset maximum value and minimum value Requesting to clear an error 2) Refer to X02(Flag indicating operation condition set up) for set/reset timing. 1) This is set when switching the channel for offset/gain calibration. 2) Refer to X03(Flag indicating channel switched) for set/reset timing 1) This is set when the calibrated values of offsets/gains are registered to A/D module. 2) Refer to X04(Flag indicating offset/gain calibration mode) for set/reset timing. 1) This is set when assigning offset/gain calibration mode. 2) When it is reset, normal mode(a/d Conversion mode. 3) If offsets/gains are set up, this is to be reset. 1) If the request to reset maximum value and minimum value is set, the maximum value and minimum value stored in buffer memory will be cleared. 2) After this is set, this is to be reset. 1) This is set to clear the error. 2) Refer to X0F(Flag indicating an error in A/D module) for set/reset timing Buffer Memory Address Description Address Description Hexa Deci Hexa Deci 0H 0 Enabling/disabling to A/D-convert setup 1H 1 Average time & average number of times of CH1 2H 2 Average time & average number of times of CH2 3H 3 Average time & average number of times of CH3 4H 4 Average time & average number of times of CH4 5H 5 Average time & average number of times of CH5 6H 6 Average time & average number of times of CH6 7H 7 Average time & average number of times of CH7 8H 8 Average time & average number of times of CH8 R/W 17H 23 Channel to calibrate gain R/W R/W 18H 24 Setting up digital output 1 R/W R/W 19H 25 Setting up digital output 2 R/W R/W 1AH 26 Not use R/W 1BH 27 R/W 1CH 28 R/W 1DH 29 R/W 1EH 30 Max. value of CH1 R R/W 1FH 31 Min. value of CH1 R 9H 9 Assigning averaging process R/W 20H 32 Max. value of CH2 R AH 10 Flag indicating A/D-converted R 21H 33 Min. value of CH2 R BH 11 Digital output value of CH1 R 22H 34 Max. value of CH3 R CH 12 Digital output value of CH2 R 23H 35 Min. value of CH3 R DH 13 Digital output value of CH3 R 24H 36 Max. value of CH4 R
16 1274 CIMON-PLC EH 14 Digital output value of CH4 R 25H 37 Min. value of CH4 R FH 15 Digital output value of CH5 R 26H 38 Max. value of CH5 R 10H 16 Digital output value of CH6 R 27H 39 Min. value of CH5 R 11H 17 Digital output value of CH7 R 28H 40 Max. value of CH6 R 12H 18 Digital output value of CH8 R 29H 41 Min. value of CH6 R 13H 19 Error code R 2AH 42 Max. value of CH7 R 14H 20 Set range(ch1 ~ CH4) R/W 2BH 43 Min. value of CH7 R 15H 21 Set range(ch5 ~ CH8) R/W 2CH 44 Max. value of CH8 R 16H 22 Channel to calibrate offset R/W 2DH 45 Min. value of CH8 R Each data is word type. Buffer memory from CH.5 to CH.8 cannot be used for 4-channel module. R/W indicates whether reading/writing from a PLC is enabled. (R : Reading is enabled. / W : Writing is enabled.) Enabling / Disabling to A/D Convert (Address "0") Buffer Memory Address "0" This is used to set up whether enabling or disabling to A/D-convert by the channels. To make it available to set up enabling/disabling to A/D-convert, requesting to set up operation condition (Y02) is to be set and reset. Default value is set up as disabling A/D conversion. As a set value is stored in EEPROM, the A/D module is operated as previously set value even though the power is on and off. The data from b4 to b15 of AD04VI and the data from b8 to b15 of AD08I and ADO8V are fixed as "0". Example : In case that the channels for A/D conversion are 2,4,6,8, 00AAH(170) is to be written to Buffer Memory Address "0" and requesting to set up operation condition (Y02) is to be set and reset.
17 XP / CP Series(CM1) Average Time / Average Number of Times (Address "1-8") Buffer Memory Address "1 ~ 8" These are used to set up the average time and the average number of times for an assigned channel. To make the setup available, requesting to set up operation condition (Y02) is to be set and reset. The ranges available to set up are as follows. ( Average process by number of times: 4 ~ times / Average process by time: 20 ~ 5000ms ) Default value is fixed as "0". As a set value is stored in EEPROM, the A/D module is operated as previously set value even though the power is on and off Assigning Average Process (Address "9") Buffer Memory Address "9" Use the CICON to select sampling process or average process, and to write a set value to Buffer Memory "9" To make the setup available, requesting to set up operation condition (Y02) is to be set and reset. In case that average process is selected, use the CICON to select average time or number of times. Default value is set up as the sampling process and averaging number of times for all channels. As a set value is stored in EEPROM, the A/D module is operated as previously set value even though the power is on and off. Assigning the channels for average process 1 : Average Process 0 : Sampling Process Assigning time and number of times 1 : Averaging Time 0 : Averaging Number of Times
18 1276 CIMON-PLC Example : In case that Channel 1 and 5 are assigned to averaging number of times, Channel 2 and 7 to averaging time and the rest to the sampling process, requesting to set up operation condition(y02) is set and reset after 5342H(21314) is stored in Buffer Memory Address "9" A/D Converted (Address "10") Buffer Memory Address "10" If an assigned channel is A/D-converted first, the memory for A/D-converted will be set. And, flag indicating A/D-converted (X02) will be set if all channels are A/D-converted first If requesting to set up operation condition (Y03) is on, the memory will be reset. And if a corresponding channel is A/D-converted, the memory will be set. In case of 4-channel module, the data from b4 to b7(ch5 ~ CH8) are disregarded. 1 : A/D Converted / 0 : A/D Converting or not use The data from b4 of AD04VI and the data from b8 to b15 of AD08I and AD08V are fixed as "0". Example : When Channel 1,2 and 6 are enabled to A/D-convert and all the channels A/D-convert, 0023H(35) is stored in Buffer Memory Address?0?as follows.
19 XP / CP Series(CM1) Digital OutPut Value (Address "11-18") Buffer Memory Address "11 ~ 18" A/D-converted digital output values are stored in buffer memory addresses from 11 to 18 by channels. Digital output values are indicated in signed 16-bit binary value. The range of output values is from 0(-8000) to 16000(8000). In case that values are out of the range, they are outputted in the range from 192 to or 8192 to Error Codes (Address "19") Buffer Memory Address "19" The error codes detected from an A/D module are stored in these addresses. is from 1 to 4 for AD04VI and from 1 to 8 for AD08I and AD08V(The number means the channel.).?is from 1 to 3. If an error occurs, it will be kept till it is cleared or the power is off. If an error is not cleared after it occurs, an newly occurring error will be disregarded. (To clear an error, use the CICON to set or reset the YOF (Requesting to clear error).) [ Error codes are decimal figure.] Error code Description 1 The case that the range of input setup is wrong The case that current is set up in AD08V or voltage is set up in AD08I 2 The case that average process time is out of range 3 The case that number of average process times is out of range 4 The case that an offset value is greater than a gain value 49 The case that offset channels and gain channels are calibrated at the same time 10 Error in system (A/S required)
20 1278 CIMON-PLC Range of Input Setup (Address "20, 21") Buffer Memory Address "20","21" These are used to set up the range of inputs by channels for an A/D converter module. To make the setup available, requesting to set up operation condition(y02) is to be set and reset. The set values of the channels from 1 to 4 are stored in Buffer Memory Address "20" and the set values of the channels from 5 to 8 are stored in Buffer Memory Address "21". In case of 4-channel module, Buffer Memory Address "21" is disregarded. The range of the default values for AD04VI, AD08I is from 4 to 20(mA) and the range for AD08V is from 1 to 5V. As a set value is stored in EEPROM, the A/D module is operated as previously set value even though the power is on and off. Buffer Memory Address "20" Buffer Memory Address "21" b15 ~ 12 b11 ~ b8 b7 ~ b4 b3 ~ b0 CH 4 CH 3 CH 2 CH 1 CH 8 CH 7 CH 6 CH 5 The set values are as follows. Range of Input Set Value 4 ~ 20(mA) 0 0 ~ 20(mA) 1 1 ~ 5(V) 2 0 ~`5(V) 3-10 ~ 10(V) 4 0 ~ 10(V) Offset/Gain Calibration Mode (Address "22, 23") Buffer Memory Address "22", "23" These are used to assign the channel of which offset/gain are calibrated. The channel to calibrate an offset is assigned to Buffer Memory Address "22" and the channel to calibrate an gain is assigned to Buffer Memory Address "23". It is available to set up two channels at the same time. But, an offset and a gain is to be calibrated each. (One of Buffer Memory Address "22" and "23" should be set up as "0".) If both are set up at the same time, an error(error code "49") occurs in offset/gain calibration mode. In case of a 4-channel module, the data from b4 to b7(for channels from 5 to 8) are disregarded.
21 XP / CP Series(CM1) Digital Output Setup Mode (Address "24, 25") Buffer Memory Address "24, 25" This is used to decide whether the range of digital output value is -192 ~ 16191, ~ 8191, 0 ~ 16000, ~ To make this setup available, requesting to set up operation condition (Y02) is to be set and reset. If the corresponding bit of each channel is 0, the range of values is from 192 to If it is 1, the range of values is from to Default value is set up as 0(-192~16191). As a set value is stored in EEPROM, the A/D module is operated as previously set value even though the power is on and off. Address 24 Address 25 Digital Output ~ ~ ~ ~ 8000
22
USER S MANUAL. FX2N-8AD Analog input block
USER S MANUAL FX2N-8AD Analog input block FX2N-8AD Analog input block Foreword This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation
More informationUser s Manual. LG Industrial Systems G3F AT4A. LG Programmable Logic Controller
User s Manual LG Programmable Logic Controller G3F AT4A GLOFA G4F AT3A LG Industrial Systems CONTENTS Chapter 1. INTRODUCTION 1.1 Features 1-1 Chapter 2. SYSTEM CONFIGURATION 2.1 Example of System Configuration
More informationMELSEC-L Digital-Analog Converter Module User's Manual -L60DA4 -L60DAVL8 -L60DAIL8
MELSEC-L Digital-Analog Converter Module User's Manual -L60DA4 -L60DAVL8 -L60DAIL8 SAFETY PRECAUTIONS (Read these precautions before using this product.) Before using this product, please read this manual
More informationDisplacement sensor control unit UQ1 series. User s manual
Displacement sensor control unit UQ1 series User s manual Introduction Thank you for purchasing the displacement sensor I/F unit UQ1 series. Before using this product, please con rm this product is what
More informationSAFETY PRECAUTIONS. (Read these precautions before using this product.)
SAFETY PRECAUTIONS (Read these precautions before using this product.) Before using this product, please read this manual and the relevant manuals carefully and pay full attention to safety to handle the
More informationDATA SHEET. The Advantys model STBDAI5260 Digital Input Module provides 2 isolated discrete input points that operate on a 115 VAC power source.
Advantys STB Advantys STB Input Module DATA SHEET Description The Advantys model STBDAI5260 Digital Input Module provides 2 isolated discrete input points that operate on a 115 VAC power source. Features
More informationLX3V-4AD User manual Website: Technical Support: Skype: Phone: QQ Group: Technical forum:
User manual Website: http://www.we-con.com.cn/en Technical Support: support@we-con.com.cn Skype: fcwkkj Phone: 86-591-87868869 QQ Group: 465230233 Technical forum: http://wecon.freeforums.net/ 1. Introduction
More informationAdvantys STB DATA SHEET. Advantys STB Output Module. Description. Features
Advantys STB Advantys STB Output Module DATA SHEET Description The Advantys model STBDAO5260 Digital Output Module provides 2 isolated discrete output points that operate on a 115 VAC power source. The
More informationSelf--powered Time Counter
Self--powered Time Counter Subminiature Time Counters With Enhanced Appearance and Features Large display with 8.6 mm (0.338 in) height Available with backlit LCD PNP/NPN DC voltage available Sevendigits,timerange0to
More informationINTRODUCTION TERMINAL LAYOUTS FX2N-4AD SPECIAL FUNCTION BLOCK USER S GUIDE
FX2N-4AD SPECIAL FUNCTION BLOCK USER S GUIDE JY992D6520B This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N-4AD and should
More informationANALOG I/O MODULES AD268 / DA264 / TC218 USER S MANUAL
UM-TS02 -E026 PROGRAMMABLE CONTROLLER PROSEC T2-series ANALOG I/O MODULES AD268 / DA264 / TC218 USER S MANUAL TOSHIBA CORPORATION Important Information Misuse of this equipment can result in property damage
More informationScanning Laser Range Finder Smart-URG mini UST-10LX (UUST003) Specification
Date: 2014.6.12 Scanning Laser Range Finder Smart-URG mini UST-10LX (UUST003) Specification RoHS Symbol Amended Reason Pages Date Amended by Ref.No Approved by Checked by Drawn by Designed by Title UST-10LX
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) This product is no longer carried in our catalog. AFG 2020 Characteristics Features Ordering Information Characteristics
More informationSlot-type Photomicrosensor with connector or pre-wired models (Non-modulated) *1. configuration. Dark-ON/Light-ON
Slot-type Photomicrosensor with connector or pre-wired models (Non-modulated) * EE-SX/6 Photomicrosensor with 0- to 00-mA direct switching capacity for built-in application. Series includes models that
More informationAnalogue Inputs Resolution Assignment
Analogue Inputs Resolution Assignment a) Describe the relationship between the number of bits used in an analogue signal and the resolution available. b) A system has a level sensor which measures the
More informationLCD MODULE SPECIFICATION
TECHNOLOGY CO., LTD. LCD MODULE SPECIFICATION Model : MI0220IT-1 Revision Engineering Date Our Reference DOCUMENT REVISION HISTORY DOCUMENT REVISION DATE DESCRIPTION FROM TO A 2008.03.10 First Release.
More informationTime-Lag Relays. User s Handbook (General Model)
Time-Lag Relays User s Handbook (General Model) 651.601.387 Rev: V39 Date: 09/2016 Electrotécnica Arteche Smart Grid, S.L. This document, including texts, photos, graphics and any other content, is protected
More information20 mm Beam Pitch General Purpose Area Sensor. Distance between parts shelf and sensor can be shortened (Enables miniaturization of equipment)
OTHER SUNX PRODUCTS SERIES 0 mm Beam Pitch General Purpose Area Sensor Diagnosis Self-diagnosis Test input Interference prevention Wide sensing area of 7 m,60 mm with 0 mm beam pitch Refer to p.9l for
More informationWECON LX3V-2PT2DA BD Board
WECON LX3V-2PT2DA BD Board Website: http://wwwwe-concomcn/en Technical Support: liux@we-concomcn Skype: fcwkkj Phone: 86-591-87868869 Technical forum: http://weconfreeforumsnet/ Ⅰ Mounting instruction
More informationE6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm
Low-cost Encoder with Diameter of 50 mm CSM DS_E An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. High-precision detection of automatic machine timing.
More informationType Contact form Model Ag (Au clad) Standard DPDT G6A-274P-ST-US Low-sensitivity DPDT G6A-274P-ST40-US
Low Signal Relay G6A Fullly Sealed Relay with High Impulse Withstand High sensitivity can be driven by digital circuits. Low-profile design allows use in 12.70 mm PC board rack. Surge withstand meets FCC
More informationR1MS-GH3 BEFORE USE... POINTS OF CAUTION INSTRUCTION MANUAL THERMOCOUPLE & DC INPUT MODULE MODEL. (8 points; isolated)
INSTRUCTION MANUAL THERMOCOUPLE & INPUT MODULE (8 points; isolated) MODEL BEFORE USE... Thank you for choosing M-System. Before use, please check contents of the package you received as outlined below.
More informationOcean Sensor Systems, Inc. Wave Staff, OSSI F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff
Ocean Sensor Systems, Inc. Wave Staff, OSSI-010-002F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff General Description The OSSI-010-002E Wave Staff is a water level sensor that
More information1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times
Color Mark Color Mark Feature Outstanding color matching accuracy - RGB light emitting diodes and 12-bit resolution - 2 detection modes (color only / color + intensity) - -step sensitivity adjustment for
More informationAgilent Agilent 86120B, 86120C, 86122A Multi-Wavelength Meters Data Sheet
Agilent Agilent 86120B, 86120C, 86122A Multi-Wavelength Meters Data Sheet Agilent multi-wavelength meters are Michelson interferometer-based instruments that measure wavelength and optical power of laser
More informationIPC-DT/H20X(PC)T IPC-DT/M20V(PC)T, IPC-DT/L20S(PC)T, IPC-DT/H20X(PC)T. Option. Features. Ver.1.10
Panel-Mount with Analog RGB FLAT PANEL DISPLAY IPC-DT/M20V(PC)T 10.-inch TFT color LCD (60 x80 dots ) IPC-DT/L20S(PC)T 12.1-inch TFT color LCD (800 x600 dots ) IPC-DT/H20X(PC)T 1-inch TFT color LCD (102
More informationCylindrical Photoelectric Sensor CY-100 SERIES
Cylindrical Photoelectric Sensor CY-00 SERIES Listing (2 m cable length type only) Features Wide product range Shape: Standard type Side view type Connector: 2 m cable length type M2 plug-in connector
More informationLONWORKS Fibre Optic Converter
LONWORKS Fiber Optic Converter LRW-102 and LRW-102/PP LONWORKS to fibre optic link, multidrop and redundant ring applications The LRW-102 is a fibre optic modem designed for multidrop and redundant ring
More informationAgilent 86120B, 86120C, 86122A Multi-Wavelength Meters Technical Specifications
Agilent 86120B, 86120C, 86122A Multi-Wavelength Meters Technical Specifications March 2006 Agilent multi-wavelength meters are Michelson interferometer-based instruments that measure wavelength and optical
More informationGT1030-LBD(W) / GT1030-LBD(W)2 GT1020-LBD(W) / GT1020-LBD(W)2 / GT1020-LBL(W)
GRAPHIC OPERATION TERMINAL GT1030-LBD(W) / GT1030-LBD(W)2 GT1020-LBD(W) / GT1020-LBD(W)2 / GT1020-LBL(W) N E W GT1030-LBD GT1030-LBD2 N E W GT1030-LBDW GT1030-LBDW2 N E W GT1020-LBDW GT1020-LBDW2 GT1020-LBLW
More informationWECON LX3V-2TC2DA BD Board
WECON LX3V-2TC2DA BD Board Website: http://wwwwe-concomcn/en Technical Support: liux@we-concomcn Skype: fcwkkj Phone: 86-591-87868869 Tech Group Num: 465230233 Technical forum: http://weconfreeforumsnet/
More information02/11/2015
DIN Rail Mount 17.5 mm MUS/MUSF 80 AC/DC Part number 84872141 Control relays monitoring their own power supply - MUS : Over/undervoltage control Selectable latching (memory) function - MUSF : Over/undervoltage
More informationType Contact form Model PCB SPDT G6E-134P-ST-US G6E-134PL-ST-US. Type Contact form Model
Low Signal Relay G6E Subminiature 7.87 H x.1 W x 16 L mm (0.31 H x 0.3 W x 0.63 L in). High sensitivity with pick-up coil power of 8 mw. Surge withstand meets FCC Part 68 rule and Telcordia 2.5 kv Specifications.
More informationCC-Link IE Field Network Analog-Digital Converter Module User's Manual -NZ2GF2BN-60AD4 -NZ2EX2B-60AD4
CC-Link IE Field Network Analog-Digital Converter Module User's Manual -NZ2GF2BN-60AD4 -NZ2EX2B-60AD4 SAFETY PRECAUTIONS (Read these precautions before using this product.) Before using this product,
More informationC200H-AD002/DA002 Analog I/O Units Operation Guide
C200H-AD002/DA002 Analog I/O Units Operation Guide Revised September 1995 Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes
More informationVoltage inputs: High and low signal voltages (count, reset, short, counter No. selection, I/O inhibit) No-contact outputs: RUN, forecast
Multi-maintenance Counter/Timer (DIN 72 x 72) CSM DS_E_4_1 Nine Built-in Counters/Timers to Measure Equipment Operating Cycles and Times and Forecast Maintenance Timing Provides up to nine counters or
More informationData Pattern Generator
Data Pattern Generator DG2040 * DG2030 * DG2020A * P3410/P3420 Characteristics DG2040. Features Specs Ordering Information Pricing Information Print Data Sheet (61kB) Request a Quote Output Data Data Rate
More informationK3NX Process Meter OPERATION MANUAL
Cat.No. N90 E1 1 K3NX Process Meter OPERATION MANUAL K3NX Process Meter Operation Manual Produced January 1998 Notice: OMRON products are manufactured for use according to proper procedures by a qualified
More informationProduct Data Sheet 4656 EZ
The engineer's choice 4656 EZ INDEX 1 General... 3 2 Mechanics... 3 2.1 GENERAL... 3 2.2 CONNECTIONS... 4 3 Operating Data... 5 3.1 ELECTRICAL OPERATING DATA... 5 3.2 OPERATING DATA - ELECTRICAL INTERFACE
More informationAPPROVED BY CUSTOMER
WE ARE PLEASED IN SENDDING YOU HEREWITH OUR SPECIFICATION AND DRAWING FOR YOUR APPROVAL. PLEASE RETURN TO US ONE COPY OF FOR APPOVAL WITH YOUR APPROVED SIGNATURES. YOUR MODULE NO.: OUR MODULE NO.: K430WQC-V3-FF
More informationRK-2 ENVIRONMENTAL DATA CONTACTLESS MAGNETOSTRICTIVE LINEAR POSITION TRANSDUCER WITH FLANGED HEAD. Main characteristics
RK-2 CONTACTLESS MAGNETOSTRICTIVE LINEAR POSITION TRANSDUCER WITH FLANGED HEAD (ANALOG OR START/STOP OUTPUT) Main characteristics Absolute transducer Strokes from 50 to 4000mm (RK-2- -N/E/S) Digital output
More informationFibre Optic Modem ODW-622
Fibre Optic Modem ODW-622 RS-232 to fibre optic link, redundant ring or multidrop applications The ODW-622 can be used to create either redundant ring or multidrop solutions for devices with RS-232 interfaces.
More informationVoltage inputs: High and low signal voltages (count, reset, short, counter No. selection, I/O inhibit) No-contact outputs: RUN, forecast
Multi-maintenance Counter/Timer (DIN 72 x 72) CSM DS_E_5_4 Nine Built-in Counters/Timers to Measure Equipment Operating Cycles and Times and Forecast Maintenance Timing Provides up to nine counters or
More informationSelf-powered Totalizer
Self-powered Totalizer New H7E Compact Economical Totalizer with High Visibility Available with Backlit LCD Display Large display with 8.6-mm character height. Includes new models with backlight for improved
More informationAgilent 86120B, 86120C, 86122B Multi-Wavelength Meters. Data Sheet
Agilent 86120B, 86120C, 86122B Multi-Wavelength Meters Data Sheet Agilent multi-wavelength meters are Michelson interferometer-based instruments that measure wavelength and optical power of laser light
More informationAF-300 E11 Adjustable Frequency Drive
AF-300 E11 Adjustable Frequency Drive The AF-300 E11 adjustable frequency drive is GE s new generation of micro drives. GE recognized your need for a high-performance, full-featured compact drive and designed
More informationMultifunction Digital Timer
Multifunction Digital Timer 72 x72 mm Timer with Easy-to-use Functions Nine output modes accommodate a wide variety of applications. All parameters set by scroll-through menus accessed from the front panel.
More informationFrequency. Range. HP 83751A/B: 2 GHz to 20 GHz HP 83752A/B: 10 MHz to 20 GHz. Standard 10 MHz timebase: f10 ppm
Frequency Range HP 83751A/B: 2 GHz to 20 GHz HP 83752A/B: 10 MHz to 20 GHz Timebase Stability Standard 10 MHz timebase: f10 ppm High stability timebase (Option le5): Accuracy = Calibration &Aging rate
More informationOrdering Information. Self -P owered Count Totalizer H7EC. Subminiature Total Counters With Improved Appearance and Features
R Self -P owered Count Totalizer Subminiature Total Counters With Improved Appearance and Features H Large display with 8.6 mm (0.338 in) height H Available with backlit LCD H PNP/NPN DC voltage input
More informationSafety Light Curtains GuardShield
Description The Allen-Bradley Guardmaster safety light curtain is an economical, fully featured, Type 4 safety light curtain in a uniquely styled housing. safety light curtains are general purpose presence
More informationFX-4AD-TC SPECIAL FUNCTION BLOCK USER'S GUIDE
FX-4AD-TC SPECIAL FUNCTION BLOCK USER'S GUIDE JY992D55901A This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX-4AD-TC special
More informationFibre optic router for TP/FT-10 LRW-112PP
Fibre optic router for TP/FT-10 LRW-112PP Lo n Wo r k s to fibre optic link, point-to-point applications The LRW-112PP router offers an easy way to extend the distance between LONWORKS 78 kbit/s TP/FT
More informationAS09..S 3-pole Contactors - Spring Terminals
4 kw 5 hp AS09..S 3-pole Contactors - Spring AC Operated Description - 3-pole contactors with spring terminals, - N.C. or N.O. built-in auxiliary contact, - Rail-mounted, no tools required, - Additional
More informationOrdering Information. Absolute 60-mm-dia. Rotary Encoder E6F-A. High Accuracy and Durability for Automatic Equipment.
Absolute 60-mm-dia. Rotary Encoder A High Accuracy and Durability for Automatic Equipment Stronger shaft and greater durability (120 N in the radial direction and 50 N in the thrust direction) than previous
More informationØ50mm Shaft Multi-Turn Absolute Type
Ø50mm Shaft Multi-Turn Absolute Type Diameter Ø50mm Shaft Type Multi-Turn Absolute otary Encoder Features Total 23-bit resolution (8388608-division) of 10-bit single-turn (1024-division) and 13-bit multi-turn
More informationTeSys contactors. Model d. Type of contactor LC1- LC1- LC1- LC1- LC1-D115 & D09 D18 D25 D38 D40 D50 D95 LC1-D150 DT20 & DT25 DT32 & DT40
Characteristics Type of contactor LC- LC- LC- LC- LC-D & D09 D8 D2 D38 D40 D0 D9 LC-D0 DT20 & DT2 DT32 & DT40 Environment Rated insulation voltage (Ui) Conforming to IEC 947-4-, overvoltage category III,
More informationAssembly. Front view. LEDs. Parametrization interface. Power Bus
otation Speed Monitor Features Assembly 1-channel signal conditioner 2 V DC supply Input for 2- or -wire sensors Input frequency 10 mhz... 50 khz elay contact output Start-up override and restart inhibit
More informationSINAMICS G130. dv/dt filter plus Voltage Peak Limiter. Operating Instructions 03/2013 SINAMICS
SINAMICS G130 Operating Instructions 03/2013 SINAMICS s dv/dt filter plus Voltage Peak Limiter Safety information 1 General 2 SINAMICS SINAMICS G130 Operating Instructions Mechanical installation 3 Electrical
More information7 SegmneDisplay Unit With High Bright Characters (D1SC-N : W32 H57mm, D1SA Series: W11 H22mm)
SC-N/SA Series 7 Segment Display Unit 7 SegmneDisplay Unit With High Bright Characters (SC-N : W32 H57mm, SA Series: W H22mm) Features Selectable decimal (0 to 9) or hexadecimal (0 to 9, A to F) indication
More informationHPX-T Series. Auto-tuning Fiber Optic Photoelectric Control. Specifications CLICK FEATURES AMPLIFIER UNIT ORDER GUIDE. No.
6 HPX-T Series Au-tuning Fiber Optic Phoelectric Control Specifications FEATURES Built-in Au-tuning Aumatically Adjusts Scanning Characteristics. Adjustment Steps, Results and Scanning Conditions Digitally
More informationMELSEC System Q. QJ71PB92D PROFIBUS/DP Interface Module. Programmable Logic Controllers. User's Manual MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC
MITSUBISHI ELECTRIC MELSEC System Q Programmable Logic Controllers User's Manual QJ71PB92D PROFIBUS/DP Interface Module Art. no.: 136267 10 04 2004 SH (NA) 08012 Version C MITSUBISHI ELECTRIC INDUSTRIAL
More informationEVENT INPUT/OUTPUT MODULE [PUME]
PUM Series Multi-loop module type Temperature controller DATA SHEET EVENT INPUT/OUTPUT MODULE [] is a digital input/output module used as an auxiliary input/output of control modules. Each module, 30mm
More informationWeekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N
Weekly Timer 1/4 DIN Size Timer Features Prompted Programming and Large LCD Display 24 hours x 7 days programming using just 5 switches 16 program steps and cycle operation Two independent 15 A control
More informationRF Semiconductor Test AXRF RF Port Upgrade Kits
RF Semiconductor Test AXRF RF Port Upgrade Kits 2017 Datasheet The most important thing we build is trust Overview AXRF RF Port Upgrade Kits are designed to improve and extend the capability of an existing
More informationpotentiostat/galvanostat
potentiostat/galvanostat Rev. 12-2012 potentiostat/galvanostat A battery-powered, handheld instrument which allows the application of most of the relevant voltammetric and amperometric techniques. The
More informationINTRODUCTION TERMINAL LAYOUTS FX2N-4AD-TC SPECIAL FUNCTION BLOCK USER S GUIDE
FX2N-4AD-TC SPECIAL FUNCTION BLOCK USER S GUIDE JY992D65501A This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N-4AD-TC
More informationLX3V-2PT-BD User manual
User manual Website: http://www.we-con.com.cn/en Technical Support: support@we-con.com.cn Skype: fcwkkj Phone: 86-591-87868869 QQ: 1043098682 Technical forum: http://wecon.freeforums.net/ 1. Mounting instruction
More informationSelf-powered Totalizer New H7E
Self-powered Totalizer New H7E CSM_H7E_-N_DS_E_7_1 Compact Economical Totalizer with High Visibility Available with Backlit LCD Display Large display with 8.6-mm character height. Includes new models with
More informationLONWORKS Fibre Optic Router
LONWORKS Fiber Optic Router LRW-112 and LRW-112/PP LONWORKS to fibre optic link, multidrop and redundant ring applications The LRW-112 router offers an easy way to extend the distance between LONWORKS
More informationRack mounted telephone- and leased line modem for industrial applications
Rack mounted telephone- and leased line modem for industrial applications TR-6 Rack modem for industrial PSTNand /-wire leased line applications The TR-6 is an analogue V. 9 -rack PSTN modem as well as
More informationAbsolute Rotary Encoder E6CP
Absolute Rotary Encoder Absolute Rotary Encoders with Gray Code Output Gray code output decreases output errors Lightweight plastic housing Used with Omron s H8PS Cam Positioner, this encoder detects the
More informationModel Number Structure
Cycle Control Units CSM DS_E_7_1 Refer to Safety Precautions for All Power Controllers. Used in Combination with the to Enable High-precision Temperature Control Use cycle control to achieve power control
More informationWECON LX3V-2PT-BD Module
WECON Module Website: http://www.we-con.com.cn/en Technical Support: liux@we-con.com.cn Skype: fcwkkj or Jason.chen842 Phone: 86-591-87868869 QQ Group: 465230233 Technical forum: http://wecon.freeforums.net/
More informationPSI-MOS-RS232/FO 850 E Serial to Fiber Converter
PSI-MOS-RS232/FO 850 E Serial to Fiber Converter perle.com/products/serial-fiber-converters/psi-mos-rs232-fo850e-rs232-to-fiber.shtml Connect RS232 devices to fiber optic cable Extend serial data up to
More informationSAFETY PRECAUTIONS (Read these precautions before using.)
SAFETY PRECAUTIONS (Read these precautions before using.) When using Mitsubishi equipment, thoroughly read this manual and the associated manuals introduced in this manual. Also pay careful attention to
More informationProduct Data Sheet 4656 ZW
The engineer's choice 4656 ZW INDEX 1 General... 3 2 Mechanics... 3 2.1 GENERAL... 3 2.2 CONNECTIONS... 4 3 Operating Data... 5 3.1 ELECTRICAL OPERATING DATA... 5 3.2 OPERATING DATA - ELECTRICAL INTERFACE
More informationR&S RT-Zxx High-Bandwidth Probes Specifications
R&S RT-Zxx High-Bandwidth Probes Specifications Test & Measurement Data Sheet 14.00 CONTENTS Definitions... 3 Probe/oscilloscope chart... 4 R&S RT-ZZ80 transmission line probe... 5 R&S RT-ZS10/-ZS10E/-ZS20/-ZS30
More informationODW-621. RS-232 Point-to-point applications
Re-timing Data rate up to 250 kbit/s 9-position D-sub connector Redundant power supply inputs Status interface for fault indication Fibre link fault indication (Red) Design for harsh environments 40 to
More informationTOSHIBA Industrial Magnetron E3328
TOSHIBA E3328 is a fixed frequency continuous wave magnetron intended for use in the industrial microwave heating applications. The average output power is 3kW in the frequency range from 2450 to 2470
More informationR&S RT-Zxx High-Voltage and Current Probes Specifications
R&S RT-Zxx High-Voltage and Current Probes Specifications Test & Measurement Data Sheet 14.00 CONTENTS Definitions... 3 Probe/oscilloscope chart... 4 R&S RT-ZH10/-ZH11 high-voltage probes... 5 R&S RT-ZD01
More informationFibre Optic Modem ODW-611
Fibre Optic Modem ODW-611 PROFIBUS DP to fibre optic link, point-to-point applications The ODW-611 is a fibre optic modem designed for point-to-point fibre optic connections between PROFI- BUS DP networks.
More informationOcean Sensor Systems, Inc. Wave Staff III, OSSI With 0-5V & RS232 Output and A Self Grounding Coaxial Staff
Ocean Sensor Systems, Inc. Wave Staff III, OSSI-010-008 With 0-5V & RS232 Output and A Self Grounding Coaxial Staff General Description The OSSI-010-008 Wave Staff III is a water level sensor that combines
More informationSet for simple I/O communication via PROFIBUS-DP in IP20 TI-BL20-DPV1-S-8
Type code Ident no. 1545077 Number of channels 8 Dimensions (W x L x H) 110.3 x 128.9 x 74.4 mm A special software (function module) for integration in PLC systems is not required. Cable max. 50 m between
More informationSeries CT7N Bimetallic Overload Relays
Series CT7N imetallic Overload Relays Choose CT7N overloads in DC applications and when monitoring Variable Frequency Drives Sprecher + Schuh has always paid particular attention to the subject of motor
More informationLW10-T600. P10 Led Wall Display
P10 Led Wall Display PANEL Led Type 3in1 Panel Size (W*H*D) (mm) 960x960x160 Pixel Pitch 10mm Module Size (W*H) (mm) 320x160 Pixel Configuration SMD 3535 Product Weight (Kg/m2) 42 PCB Layer 2 layer Material
More information3M Sensored Termination (15 kv) QX-T15I-vi1-E
3M Sensored Termination () QX-T15I-vi1-E Data Sheet May 2016 Kit Contents: Each kit contains sufficient quantities of the following materials to make three single-phase terminations. 31" (REF) One piece
More informationProduct Data Sheet 8506 VW-691
The engineer's choice 8506 VW-691 INDEX 1 General... 3 2 Mechanics... 3 2.1 GENERAL... 3 2.2 CONNECTIONS... 4 3 Operating Data... 5 3.1 ELECTRICAL OPERATING DATA... 5 3.2 OPERATING DATA - ELECTRICAL INTERFACE
More informationFX-2DA SPECIAL FUNCTION BLOCK USER'S GUIDE
FX-2DA SPECIAL FUNCTION BLOCK USER'S GUIDE JY992D52801C This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX-2DA special
More informationDisplacement Measuring System for Cylinder Series OSP-P
-SENSOFLEX Displacement for Cylinder Series OSP-P Overview...112 Technical Data SFI-plus...113 Dimensions SFI-plus...114 Order Information...115 111 Sensoflex - Sensoflex Displacement measuring system
More informationGeneral Specifications
General Specifications WG41F11C Compact O Frame GS 14M04B10-20E-Z1 [Style: S1] Overview The WG41F11C Compact O frame is a space-saving frame designed for coating lines of battery electrode sheets. This
More informationCM-398DI. CV/SV to DVI-I Converter. Operation Manual CM-398DI
CM-398DI CV/SV to DVI-I Converter Operation Manual CM-398DI Safety Precautions Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power
More informationLC3D180AV7 TeSys D - star delta starter - 3 x 3P (3 NO) - 18 A V AC coil
Characteristics TeSys D - star delta starter - 3 x 3P (3 NO) - 18 A - 400 V AC coil Main Range Product name Product or component type Device short name Contactor application Utilisation category Device
More informationScopeMeter 190 Series Specifications
Seite 1 von 7 ScopeMeter 190 Series Specifications Product Home Features Specifications Models, Options & Accessories Oscilloscope Mode Meter Mode Recorder Mode General Specifications Oscilloscope Mode
More informationType Contact form Model
Low Signal Relay G6A High sensitivity can be driven by digital circuits. Low-profile design allows use in.70 mm (0.50 in) PC board rack. Surge withstand meets FCC Part 68 regulation. Units can be mounted
More informationIndoor Linear 80W Driver SI-C215280N2KR
Product Data Sheet Rev.00 2017. 2. 9 1# LED Driver Indoor Linear 80W Driver SI-C215280N2KR Constant Current LED Driver Features & Benefits Output Current Range: 1550mA Output Voltage Range: MAX 51 Vdc
More informationAI-1204Z-PCI. Features. 10MSPS, 12-bit Analog Input Board for PCI AI-1204Z-PCI 1. Ver.1.04
10MSPS, 12-bit Analog Board for PCI AI-1204Z-PCI * Specifications, color and design of the products are subject to change without notice. This product is a PCI bus-compliant interface board that expands
More informationOperating Instructions
Operating Instructions HAEFELY TEST AG KIT Measurement Software Version 1.0 KIT / En Date Version Responsable Changes / Reasons February 2015 1.0 Initial version WARNING Introduction i Before operating
More informationGeneral Specifications
General Specifications Models, TAS50 s Models, KMS50 Cables GENERAL This General Specification (GS) sheet describes MIL connector cables and MIL connector terminal blocks enabling connections to field
More informationPRO-3GSDIHDMI. 3G-SDI Extender with HDMI Scaler OPERATION MANUAL
PRO-3GSDIHDMI 3G-SDI Extender with HDMI Scaler OPERATION MANUAL Safety Precautions Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the
More informationPRO-SDIVGA. SDI Extender with PC/HD Scaler & Audio OPERATION MANUAL
PRO-SDIVGA SDI Extender with PC/HD Scaler & Audio OPERATION MANUAL Safety Precautions Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting
More information