STROBOSCOPE LIGHT EFFECT KIT
|
|
- Aubrey Young
- 5 years ago
- Views:
Transcription
1 STROBOSCOPE LIGHT EFFECT KIT Easy to build stroboscope for general applications Flash frequency: 5 to 15 flashes per second Power supply: 110VAC Power consumption: 13W max. PCB dimensions: 50 x 75mm modifications reserved K5300 H5300U-ED1
2 Velleman Kit nv Legen Heirweg 33 B9890 Gavere BELGIUM
3 STROBOSCOPE Today, you can see a lot of these quick flashing lights above the dance floor, giving the impression that everybody is dancing, making brusque movements. Those lamps are called stroboscopes. In fact, a stroboscope is just a flashbulb with an adequate power supply and a trigger circuit of which the frequency, in most cases, is adjustable. The frequency of this stroboscope is adjustable between 5 and 15 Hz. Some applications: Photo amateurs: making snapshots Film amateurs: lightning imitations for films Choreography Lighting in discotheques Slow motions Shop-window lighting Technical data: Power supply: 110 VAC Absorbed current: 13W max. Flash frequency: 5 to 15 Hz Dimensions: 50 x 75 mm ( 2 x 3 inch )
4 Construction: WARNING: ALL COMPONENTS ARE CONTINUOUSLY CONNECTED TO THE MAINS. DO NOT TOUCH THEM UNDER ANY CIRCUMSTANCES. IT IS ABSOLUTELY NECESSARY FOR YOU AND ANY FUTURE USER TO MAKE SURE NOBODY CAN REACH THE PARTS. BOX THE UNIT IN INSULATED HOUSING ONLY SOLDERING INSTRUCTIONS: Use a small soldering iron of 40W max. Use thin (1mm) solder tin. Careless soldering always causes problems. Heat the component lead and apply soldering tin, make sure that the solder has a shiny look. Cut the component lead, do not cut in the soldering tin. This is how a good soldering looks like
5 Mount R1 to R3, 100K 1/4W resistors. These are all the same resistors with the color code brown, black, yellow. Mount the diac D1, the diac looks like a diode but has no polarity. Mount the diodes D2 and D3, 1N4007 type diodes. Check for the polarity (the cathode is indicated by a strip on the p.c.b. and on the diode) Mount R4 the high power 330ohm/5W resistor. Pay attention. Do not mount this resistor flush to the p.c.b. Leave a 2mm (1/10") clearance.
6 Mount C1, a 0.1uF/400V capacitor. This type of capacitor has no polarity. Mount C2, a 10µF electrolytic capacitor: Check for the polarity! Mount the two pole MAINS screw connector at position J1 Mount the trigger coil L1
7 Mount C3 and C4 two 22uF/ 350V electrolytic capacitors. Check for the polarity. Mount RV1, a 470K linear potentiometer. Mount this potentiometer with its shaft turned to the outside of the print. Mount the triac TR1. Depending on the type, look at the picture for correct mounting.
8 At last, mount the strobe tube where marked TUBE. CHECK FOR THE POLARITY. The connection marked with a red strip or dot has to correspond to the + of the print. Depending on the way the kit will be incorporated in a housing, mount the tube horizontally or vertically, see the pictures. Remark: Bend the leads carefully before mounting the tube horizontally. Vertical mount Horizontal mount
9 Usage: Connect the 110VAC power supply to the points marked MAINS The flash frequency may be adjusted, between 5 and 15 flashes per second, by means of RV1. A location on the print is made to add a reflector just behind the strobe tube. It is highly recommended to put the unit in a well insulated housing to avoid touching the components because of the very high voltages. In fact, voltages up to 3kV run through the flash tube and the circuit is directly coupled to the mains. It is really unhealthy to touch these voltages!!! WARNING: ALL COMPONENTS ARE CONTINUOUSLY CONNECTED TO THE MAINS. DO NOT TOUCH THEM UNDER ANY CIRCUMSTANCES.
10
11 We guarantee the good operation of this kit when correctly assembled and used. In case of trouble you can send the kit to the dealer for repair. The repair is for free when the trouble is caused by production fault. We are not responsible for damage of any kind caused by the failure of a kit. Velleman Kit nv Legen Heirweg 33 B9890 Gavere BELGIUM
12
H2633IP-1 RELAY CARD K2633
H2633IP-1 RELAY CARD K2633 Control up to 4 high-power circuits from a low-power drive circuit. Features & Specifications The connection of a few relays to the outputs of an electronic circuit might be
More informationTotal solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 123 Difficulty level: beginner 1 2 3 4 5 advanced AUDIO ANALYZER K8098 ra audio gea Give your. look high-tech ILLUSTRATED ASSEMBLY MANUAL H8098IP-1 Features & Specifications Features
More informationTotal solder points: 117 Difficulty level: beginner advanced. RGB Controller K8088 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 117 Difficulty level: beginner 1 2 3 4 5 advanced RGB Controller K8088 Control incandescent bulbs, LEDs, common anode led strips, etc... ILLUSTRATED ASSEMBLY MANUAL H8088IP-1 Features
More informationRGB LED ADD-ON FOR K VERTEX 3D PRINTER
K8403 USER MANUAL RGB LED ADD-ON FOR K8400 - VERTEX 3D PRINTER WWW.VELLEMANPROJECTS.EU Table of contents What s in the box 3 What s on the PCB 3 PCB assembly 4 Attaching the LED strips 6 Installing the
More informationTube Cricket Build Guide
Tube Cricket Build Guide The Tube Cricket is a small-wattage amp that puts out about 1 watt of audio power. With a 12AU7 tube-preamp and a JRC386 power amp, the Tube Cricket gives you great tone in a compact
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationBill of Materials: Super Simple Water Level Control PART NO
Super Simple Water Level Control PART NO. 2169109 Design a simple water controller in which electrodes are required to sense high and low water levels in a tank. Whenever the water level falls below the
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More informationMONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 2.2 Build Instructions
More informationLINK-RAY TM MODULATORS FOR CONSTANT- VOLTAGE. LinkRay Modulators 12 V / 24 V Constant-voltage Applications MODULATORS
MUSIUM RESTAURANT SOUVENIR SHOP EXIT LinkRay Modulators 12 V / 24 V Constant-voltage Applications LINK-RAY TM MODULATORS FOR CONSTANT- VOLTAGE LINK-RAY TM MODULATORS FOR CONSTANT-VOLTAGE APPLICATIONS 186755
More informationNixie Clock Type Frank 3
Assembly Instructions And User Guide Nixie Clock Type Frank 3 Software version: 7R PCB Version: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 3 is a compact design with all
More informationMAIN PCB (The small one) OPEN MAIN BOARD BAG A
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationVU-1 VU Meter Kit Volume Unit Meter
VU-1 VU Meter Kit Volume Unit Meter Simplicity Counts, Detail Matters. No part of this document may be reproduced, either mechanically or electronically, posted online on the Internet, in whole or in part,
More informationNixie Clock Type Frank 2 Z570M
Assembly Instructions And User Guide Nixie Clock Type Frank 2 Z570M Software version: 7R PCB Revision: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 2 is a compact design with
More informationADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT
ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT BUILD INSTRUCTIONS Before you start take a look at the Printed Circuit Board (PCB). The components go in the side with the writing on
More informationTKEY-K16. Touch CW automatic electronic keyer. (No moving parts no contacts) Assembly manual. Last review: March 15, 2018
TKEY-K16 Touch CW automatic electronic keyer (No moving parts no contacts) Assembly manual Last review: March 15, 2018 Commands and use manual of the K16 and Updates and news: www.ea3gcy.com Thanks for
More informationIntroduction 1. Green status LED, controlled by output signal ST
Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away
More informationIntroduction 1. Digital inputs D6 and D7. Battery connects here (red wire to +V, black wire to 0V )
Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away
More informationMulti-Key v2.4 Multi-Function Amplifier Keying Interface
Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe
More informationMal-2 assembly guide v1.0
Mal-2 assembly guide v.0 SONIC POTIONS Schematic and BOM The BOM can be found on Google Docs Prepare the PCB Separate the PCBs using some pliers. PCB We start with the lower PCB and assemble it beginning
More informationAssembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017)
Assembly Instructions And User Guide Nixie FunKlock - 1 - Issue Number Date REVISION HISTORY 4 1 February 2017 New diode for D2 3 27 December 2013 C7 / C8 error page 15 2 7 November 2013 Errors corrected
More informationIntroduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6
Introduction 1 Welcome to the GENIE microcontroller system! The activity kit allows you to experiment with a wide variety of inputs and outputs... so why not try reading sensors, controlling lights or
More informationDEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide
DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide SPECIFICATIONS Noise Figure: < 0.8 db Gain: > 15 db Frequency Range: 3400-3500 MHz Input Voltage: 7-16 VDC Description: The 9ULNACK
More informationGUIDE TO ASSEMBLY OF ERICA SYNTHS DELAY MODULE
If you are reading this, most probably, you are about to build Erica Synths DIY DELAY module. The module is 4mm deep, skiff friendly, has solid mechanical construction and doesn t require wiring. Erica
More informationTip: Faller Mittelstadt Apartments with Controlled LED Lighting Date: , Addition
Hi All, I have had the 130926 Mittelstadt apartments shown below on my layout for a long time and thought it was about time to add LED lighting to the buildings. With my success at upgrading the Faller
More informationN3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012
N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking
More informationBuilding the BX24-AHT
Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with
More informationNixie Tube Clock Type Marsden
Assembly Instructions And User Guide Nixie Tube Clock Type Marsden Software version: RTC-1.3 PCB Revision: 16 Aug 10-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Marsden is a compact design
More informationBuild A Video Switcher
Build A Video Switcher VIDEOSISTEMAS serviciotecnico@videosistemas.com www.videosistemas.com Reprinted with permission from Electronics Now Magazine September 1997 issue Copyright Gernsback Publications,
More informationIn-Line or 75 Ohm In-Line
or 5 Ohm 1dB Adjustable Gain 800/1900 Smart Technology Contents: Quick Install Overview.... 2 Installation Diagram.... Understanding the Lights... 9 Warnings and Recommendations....11 Appearance of device
More informationN3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB
N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB Kit Components Item Qty Designator Part Color/Marking PCB 1 LCD Display 1 LCD 1602 Volt Regulator 1 U1 78L05, Black TO-92 Prescaler
More informationSN-Class Nixie Clock Kits
Assembly Instructions And User Guide SN-Class Nixie Clock Kits - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 20 November 2017 New document - 2 - 1. INTRODUCTION 1.1 About the How can the
More informationKingbright. L-7104YD-12V T-1 (3mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE
T-1 (3mm) Solid State Lamp DESCRIPTIONS The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode Electrostatic discharge and power surge
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationCOLOUR CHANGING USB LAMP KIT
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE SEE AMAZING LIGHTING EFFECTS WITH THIS COLOUR CHANGING USB LAMP KIT Version 2.1 Index of Sheets TEACHING
More informationThese are the illustrated step-by-step guidelines for upgrading your Quad 34 with the Dada Electronics upgrade-kit.
Quad 34 DIY illustrated guidelines version 2.12 These are the illustrated step-by-step guidelines for upgrading your Quad 34 with the Dada Electronics upgrade-kit. The Quad 34 is a very good preamplifier,
More information3B SCIENTIFIC PHYSICS
B SCIENTIFIC PHYSICS Triode S 11 Instruction sheet 1/15 ALF 1 5 7 1 Guide pin Connection pins Cathode plate Heater filament 5 Grid Anode 7 -mm plug for connecting anode 1. Safety instructions Hot cathode
More informationVU Meter Buffer DIY Kit
VU Meter Buffer DIY Kit Warning This document is distributed for educational purposes only. This equipment operates at potentially lethal voltages. Only trained, qualified personnel should operate, maintain,
More informationColor Organ Triple Deluxe II.
http://wwwinstructablescom/id/color-organ-triple-deluxe-ii/ Food Living Outside Play Technology Workshop Color Organ Triple Deluxe II by ledartist on January 13, 2013 Table of Contents Color Organ Triple
More informationMAKE AN RGB CONTROL KNOB.
MAKE AN RGB CONTROL KNOB. This is a knob based colour changing controller that uses a custom programmed microcontroller to pack a lot of features into a small affordable kit. The module can drive up to
More informationNixie Clock Kit V1.08 Assembly and Operation
Nixie Clock Kit V1.08 Assembly and Operation Hardware Revision 14.05.2005 Software Version 6.0 Revision 19.04.2006 This document is copyrighted. No parts of this documentation may be used commercially.
More informationELECTRONIC GAME KIT ESSENTIAL INFORMATION. Version 2.0 BUILD YOUR OWN MEMORY & REACTIONS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS BUILD YOUR OWN MEMORY & REACTIONS ELECTRONIC GAME KIT Version 2.0 Build Instructions Before
More informationType Contact form Model PCB SPDT G6E-134P-ST-US G6E-134PL-ST-US. Type Contact form Model
Low Signal Relay G6E Subminiature 7.87 H x.1 W x 16 L mm (0.31 H x 0.3 W x 0.63 L in). High sensitivity with pick-up coil power of 8 mw. Surge withstand meets FCC Part 68 rule and Telcordia 2.5 kv Specifications.
More informationAzatrax Model Railroad Track Signal Control - Single Track
Installation Guide Azatrax Model Railroad Track Signal Control - Single Track TS2 What it is: The TS2 operates one or two trackside block signals (one in each direction) on one track to simulate the block
More informationFixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationUser's Guide. Digital Stroboscope Tachometer. Model and Model
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 User's Guide Visit us at www.testequipmentdepot.com Back to the Extech 461830 Product Page Digital Stroboscope Tachometer
More informationPOINTS POSITION INDICATOR PPI4
POINTS POSITION INDICATOR PPI4 Monitors the brief positive operating voltage across points motors when they are switched Lights a corresponding led on a control panel to show the last operation of each
More informationSQM40/41 Actuators for air and gas dampers
SQM40/41 Actuators for air and gas dampers Description SQM40/41 actuators are used for the positioning of flow control valves, butterfly valves, dampers or any application requiring rotary motion. The
More informationWhile the parts are already inventoried at the factory, please verify the inventory check as you go:
Thank you for purchasing the kit for building the WJ9J DTMF controller. After building, you should read the document on operation (WJ9JDTMFControllerV5.pdf) in order to use. This is also in the link in
More informationMain PCB (The small one)
Thanks for choosing our kits! This manual is written taking with the problems that we usually find in our workshops in mind. Also the order is meant to make assembly as easy as possible. Some steps are
More information24 Volt RGB/RGA Super Flat LED Rope Part Numbers: SFR-RGB-W, SFR-RGB-B, SFR-RGA-W, SFR-RGA-B
11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com 24 Volt RGB/RGA Super Flat LED Rope Part Numbers: SFR-RGB-W, SFR-RGB-B, SFR-RGA-W, SFR-RGA-B
More informationChristmas LED Snowflake Project
Christmas LED Snowflake Project Version 1.1 (01/12/2008) The snowflake is a follow-on from my Christmas star project from a few years ago. This year I decided to make a display using only white LEDs, shaped
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationNixie Clock Type Quattro'
Assembly Instructions And User Guide Nixie Clock Type Quattro' - 1 - Issue Number Date REVISION HISTORY 2 8 Sept 2012 Errors corrected 1 27 July 2012 New document Reason for Issue - 2 - 1.1 Nixie Quattro
More informationUser Manual. Digital Stroboscope Tachometer. Model and Model
User Manual Digital Stroboscope Tachometer Model 461830 and Model 461831 Introduction Congratulations on your purchase of the Extech Digital Stroboscope Tachometer. This device measures the speed of moving
More informationTR-Plus T/R Switch Assembly and Operation Manual. Introduction
TR-Plus T/R Switch Assembly and Operation Manual Revised: 7 February 2015 2015 Tucson Amateur Packet Radio Corporation Introduction The TAPR TR-Plus is a transmit/receive ( T/R ) switch that connects a
More informationAristoMig U320w 208/230/400/460/475/500 V 3~ 50/60 Hz With cooling unit and central connection
Spare parts list Edition 060727 Valid for serial no. 310 -xxx -xxx, 445 -xxx -xxx, 620 -xxx -xxx The AristoMig 450 power source is renamed: New name Old name Mig 4500i AristoMig 450 Mig U4500i AristoMig
More informationSquareLED - Aura Bar & Matrix Beam Light 100
SquareLED - Aura Bar & Matrix Beam Light 100 1. SAFETY INSTRUCTIONS Please read these instructions carefully they include the important information about the installation usage and maintenance of this
More information120cm (4x36 Watt) incl. Splitter Instruction Manual
120cm incl. Splitter Instruction Manual Table of contents 1 Description of Device and Functions... 3 1.1 Safety Instructions... 4 2 Preparation and Installation... 5 2.1 Mounting... 5 2.2 Secure the...
More informationVK-P10SE WARRANTY REGISTRATION FORM
VK-P10SE WARRANTY REGISTRATION FORM Unit Serial Number: Customer Name: Address: Date of Purchase: Purchased From: Dealer Name: Address: IMPORTANT NOTE: In order to receive the full five-year product warranty,
More informationDIGITAL STROBOSCOPE OPERATION MANUAL. Model : DT-2239A
DIGITAL STROBOSCOPE Model : DT-2239A Your purchase of this DIGITAL STROBOSCOPE marks a step forward for you into the field of precision measurement. Although this STROBOSCOPE is a complex and delicate
More informationLED MODULES READYLINE DL
LED MODULES READYLINE DL BUILT-IN MODULE LED-MODULE READYLINE DOWNLIGHT DL WU-M-538 / WU-M-539 / WU-M-540 Typical Applications Downlights Replacement for CFL DIRECT MAINS CONNECTION REDUCED FLICKER HIGH
More informationHow to make Retractable Door Mirrors Automatic Open/Close for Volvo V
How to make Retractable Door Mirrors Automatic Open/Close for Volvo V70-2001 VER. 1.3 (electronic changed, C3 moved) 1. Why we did it? Because we did not want to spend 200 Euro for a product on the marked,
More informationRIPPLE TANK - projection, with strobe & kit
RIPPLE TANK - projection, with strobe & kit DESCRIPTION: Cat: SW3440-001 projection type with stroboscope, rippler & kit. The images created by IEC Ripple Tank Projection type are viewed from the side
More informationLEVEL ADJUST POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 1200-75 Amplifier August 2012, Rev. A LEVEL ADJUST POWER MODEL 1200 AMPLIFIER CROSS TECHNOLOGIES, INC. Data, drawings, and other material contained herein are proprietary to Cross
More informationRSH27 Nixie Tube Socket with LED
Contents: 1. Applications of the socket 2. Solder instructions of the socket 3. Drawing of the assembled socket 4. Section drawing of the socket with IN-8 tube 5. Drawing and technical data of the tube
More informationLight Emitting Diodes (LEDs)
Light Emitting Diodes (LEDs) Example: Circuit symbol: Function LEDs emit light when an electric current passes through them. Connecting and soldering LEDs must be connected the correct way round, the diagram
More informationLED Spot 300W. Please read this user manual before your operation
LED Spot 300W Please read this user manual before your operation 1. Introduction 2. General Guideline 3. Safety Instructions 4. Cleaning and Maintenance 5. Technical Parameters 6. DMX Channels 7. Remark
More informationLED Interior Lighting Sets Instruction Manual (380mm)
LED Interior Lighting Sets Instruction Manual 50703 (380mm) Manual version 1.0 December 2010 General Features The ESU LED Interior lighting set 50703 uses the most contemporary technique to supply its
More informationELECTRONIC GAME KIT TEACHING RESOURCES. Version 2.0 BUILD YOUR OWN MEMORY & REACTIONS
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE BUILD YOUR OWN MEMORY & REACTIONS ELECTRONIC GAME KIT Version 2.0 Index of Sheets TEACHING RESOURCES
More informationGA A26497 SOLID-STATE HIGH-VOLTAGE CROWBAR UTILIZING SERIES-CONNECTED THYRISTORS
GA A26497 SOLID-STATE HIGH-VOLTAGE CROWBAR by J.F. Tooker, P. Huynh, and R.W. Street JUNE 2009 DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government.
More informationRGB 5050 PixelControl LED Super Flat Rope Part Numbers: PSFR-RGB-W-20
11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com RGB 5050 PixelControl LED Super Flat Rope Part Numbers: PSFR-RGB-W-20 PixelControl LED Super
More informationLEVEL ADJUST POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 1200-07 Amplifier September 2010 Rev A MONITOR J1 LEVEL ADJUST POWER MODEL 1200 AMPLIER CROSS TECHNOLOGIES, INC. Data, drawings, and other material contained herein are proprietary
More informationUser Manual Digital Stroboscope
Page 15/04/14 V1.0 Table Of Contents 1. Features 3 2. Specifications 3 & 4 2-1 General Specification 3 & 4 2-2 Flash Tube Specification 4 3. Front Panel Description 5 3-1 Flash Tube 5 3-2 Display 5
More informationUser Manual MODEL: KKW700V. Non-Touch True Display LCD Monitor. Installation Guide. 7 True Display LCD Monitor (VGA Interface)
Non-Touch True Display LCD Monitor User Manual Installation Guide 7 True Display LCD Monitor (VGA Interface) MODEL: KKW700V i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com
More informationWP36BHD T-1 (3mm) Blinking LED Lamp
T-1 (3mm) Blinking LED Lamp DESCRIPTIONS The Bright Red source color devices are made with Gallium Phosphide Red Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is
More informationMini LED Pin Spot Light Model: PLS00571
Mini LED Pin Spot Light Model: PLS00571 1 Please read these instructions carefully before use and retain for future reference. IMPORTANT SAFETY INFORMATION When using electrical appliances basic safety
More informationInstrukcja montażu. FLEX LED Neon Instalacja
FLEX LED Neon Instalacja Instrukcja montażu Polned Sp. z o.o. ul. Falencka 7 PL05-090 Janki Tel. +48 22 4903434 +48 22 4903243 www.polned.pl info@polned.pl. Product Checking: 1) Unpack and carefully examine
More informationMODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec.
MODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec. 2017) INTRODUCTION: Small open frame video monitors were made
More informationUser guide. Stand alone Multiswitches SMC Cascadable Multiswitches SMU Amplifiers. Multiswitches
User guide SM Stand alone Multiswitches SMC Cascadable Multiswitches SMU Amplifiers Multiswitches Index General safety instructions... 4 Product installation... 5 1. SM Stand alone Multiswitches... 6 2.
More informationNutube.US. 6P1 Evaluation Board. User Manual
Nutube.US 6P1 Evaluation Board User Manual Introduction The 6P1 Evaluation Board (EVB) is a vehicle for testing and evaluating the Korg Nutube 6P1 dual triode in audio circuits. This product is designed
More informationOWNER S MANUAL MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701
OWNER S MANUAL PW MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701 ANY CHANGES OR MODIFICATIONS IN CONSTRUCTION OF THIS UNIT DEVICE WHICH IS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIACE COULD VOID
More informationParts Checklist - Please note there is no resistor R3. Diodes, LED and transistors are polarized see construction stages
Xtal Check Kit build Read me first! -------- UPDATED GUIDE------ September 12, 2018--------- The following steps are designed to get your Xtal check kit built and operational. This is a good beginner s
More informationMonochrome Video Monitors
Instructions for Use Monochrome Video Monitors En F D E NL I LTC 2009 LTC 2012 LTC 2017 Philips Communication & Security Systems GB F D E NL I Instructions for Use...1.1 Mode d emploi...2.1 Bedienungsanleitung...3.1
More informationXTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors
XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only
More information"shell" digital storage oscilloscope (Beta)
"shell" digital storage oscilloscope (Beta) 1. Main board: solder the element as the picture shows: 2. 1) Check the main board is normal or not Supply 9V power supply through the connector J7 (Note: The
More informationInstructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16)
Satellite multiswitch Instructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16) EMP-CENTAURI is a registered trademark Dear Customer, Thank you for buying the EMP-Centauri
More information7 SEGMENT LED DISPLAY KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of
More informationVersaCap Lighting System
VersaCap Lighting System Installation Instructions For Single Universe Lighting Systems Manual Version: V1.1 DFX 465 Taunton Avenue, Suite 108, West Berlin, NJ 08091 800-555-5280 www.dfxsoundvision.com
More informationNixie Clock Kit IN-12B color LED backlit Operation Manual Nixie Clock Kit IN-12B V6.0 ( All Right Reserved 2015 )
Nixie Clock Kit IN-B color LED backlit Operation Manual Nixie Clock Kit IN-B V. ( All Right Reserved ) - - Operation Manual IN-B Nixie Clock Power for your Nixie Clock The clock does not include a wall
More informationDIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX
DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX 2015 FRS & MSXpró. Translation by FRS and Supersoniqs. Table of Contents Introduction... 3 Materials needed... 3 Audio volume boost...
More informationDL-1A. RF dummy load - 50Ω 20W. Assembly manual. Last update: May 1, Thank you for constructing the DL-1A dummy load kit
DL-1A RF dummy load - 50Ω 20W Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thank you for constructing the DL-1A dummy load kit Have fun assembling it
More informationService Manual for D9100 Series Digital-Control Color Monitor
Service Manual for D9100 Series Digital-Control Color Monitor Wells-Gardner Electronics 9500 W. 55 th Street Suite A McCook, Illinois 60525-3605 (708) 290-2100 069X3015-100 Revision: B / E01025 Date: 8-24-00
More informationAS09..S 3-pole Contactors - Spring Terminals
4 kw 5 hp AS09..S 3-pole Contactors - Spring AC Operated Description - 3-pole contactors with spring terminals, - N.C. or N.O. built-in auxiliary contact, - Rail-mounted, no tools required, - Additional
More informationEmergency lighting units EM powerled
E 15 W CE CPS ED Driver for AC and DC power supplies Product description ED Driver for mains operation with integrated Simple CORRIDOR FUCTIO (CF) For use in central battery systems For luminaire installation
More informationLVDT. Inductive Position Transducer - Hydraulic Series. SM-HYD Hydraulic Series. Key-Features:
HM 1808 LVDT Inductive Position Transducer - Hydraulic Series SM-HYD Hydraulic Series Key-Features: Content: - Screw flange M18x1,5 / M30x1,5 or plug-in flange Ø18 - Pressure up to 400 bar - Measurement
More informationZ-D-IN. RS485 Modbus Module 5 Digital Inputs
S SENECA Z-PC Line EN Installation Manual Contents: - General Specifications - Technical Specifications - Installation Rules - Electrical connections - Modbus connection rules - DIP-switches Settings -
More informationOPERATING INSTRUCTIONS FOR SYLVANIA. Type I08 Cathode-Ray Oscilloscope. Sylvania Electric Products Inc. Industrial Apparatus. Emporium, Pennsylvania
OPERATING INSTRUCTIONS FOR SYLVANIA Type I08 Cathode-Ray Oscilloscope Sylvania Electric Products Inc. Industrial Apparatus Plant Emporium, Pennsylvania OPERATING INSTRUCTIONS FOR Sylvania Type 08 Cathode-Ray
More informationLab 7: Soldering - Traffic Light Controller ReadMeFirst
Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two-way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been
More information