LNB Conversion Instructions for TracVision C3/R5/R4

Transcription

1 LNB Conversion Instructions for TracVision C3/R5/R4 These instructions explain how to change between a circular (North American-type) LNB and a linear (European-type) LNB in a TracVision C3/R5/R4 system. Installation Steps Changing from Linear to Circular 1. Change the LNB Check for Flash Wizard Updates Flash Both Antenna Boards Install New Satellites...4 Changing from Circular to Linear 1. Check for Flash Wizard Updates Flash Both Antenna Boards Install New Satellites Determine the Proper Skew Angle Change the LNB Set the Skew Angle...10 Tools Required This procedure requires the following tools: 9/64" allen wrench 7/16" open-end wrench Phillips-head screwdriver PC with the latest version of the KVH Flash Update Wizard installed NOTE: The Flash Update Wizard is available to KVHauthorized dealers through the KVH Partner Portal. Technical Support If you need technical assistance, please contact KVH Technical Support: N. America, S. America, Australia: Phone: techs@kvh.com Europe, Middle East, Asia: Phone: support@kvh.dk KVH, TracVision, and the unique light-colored dome with contrasting baseplate are registered trademarks of KVH Industries, Inc. All other trademarks are property of their respective companies. The information in this document is subject to change without notice. No company shall be liable for errors contained herein KVH Industries, Inc., All rights reserved Rev. B 1

2 Changing from a Linear LNB to a Circular LNB The following steps explain how to change from a linear (European-type) LNB to a circular (North American-type) LNB. If you need to change from a circular LNB to a linear LNB, refer to Changing from a Circular LNB to a Linear LNB on page 6. Step 1 - Change the LNB CAUTION For your own safety, be sure to disconnect power from all wired components before performing this procedure. Figure 1 Radome Screws/LNB Types Radome Screw and Washer (x8) Baseplate a. Disconnect power from the TracVision system and any connected receivers and/or multiswitch. 2 b. Remove the eight screws and washers securing the radome (see Figure 1). Then remove the radome and set it aside in a safe place. c. Using a 7/16" open-end wrench, disconnect the RF cable from the RF connector on the LNB (see Figure 2). d. Using a 9/64" allen wrench, remove the two LNB bracket screws and washers securing the LNB (see Figure 2). e. Carefully expand the LNB bracket just wide enough to lift the LNB from the LNB bracket. Remove the LNB. f. Place the circular LNB into the LNB bracket, and orient it as shown in Figure 3. Ensure the LNB is mounted parallel to the baseplate. g. Insert the new allen screws and washers supplied in the kitpack into the LNB bracket. NOTE: Be sure to use the allen screws supplied in the kitpack to secure the LNB. The circular LNB requires shorter allen screws. Circular LNB Figure 2 LNB RF Connector/Bracket Screws RF Connector Linear LNB Screws and Washers Figure 3 Circular LNB Orientation (Top View) LNB LNB SKEW Screw (x2)

3 h. Adjust the LNB to maintain a 3/16" gap between the LNB flange and the LNB bracket (see Figure 4). i. Hand-tighten both LNB bracket screws. Be sure to alternate the tightening of the screws to maintain a balanced grip on the LNB. j. Using a 9/64" allen wrench, tighten the two LNB bracket screws securing the LNB in the following manner: tighten one screw one full turn, then tighten the second screw one full turn; repeat until the LNB no longer rotates freely. k. Tighten the two LNB bracket screws an additional 1/4 turn. l. Reconnect the RF cable you disconnected in Step 1c on page 2 to the top RF connector on the new LNB (see Figure 5). m. Cut the center tie-wrap located on the reflector arm to release the second RF cable. Then connect the cable to the bottom RF connector on the LNB (see Figure 5). n. Reinstall the radome. Then reconnect power to the TracVision system. Step 2 - Check for Flash Wizard Updates You need to check for flash file updates to ensure you have the most current software available (see Figure 6). Follow the Flash Update Wizard s onscreen instructions to check for updates. This procedure requires a PC with the latest version of the KVH Flash Update Wizard installed and an Internet connection. Figure 4 3/16" Gap Between LNB Flange and Bracket Figure 5 LNB Connectors and RF Cables RF Cable Center Tie-wrap Figure 6 Check for Updates Option LNB Flange 3/16" Gap Top RF Connector NOTE: Refer to the Flash Update Wizard s Help file for details on checking for updates. Step 3 - Flash Both Antenna Boards Connect a PC to your TracVision system, as described in the Flash Update Wizard s Help file. Then follow the Flash Update Wizard s onscreen instructions to flash the antenna s main and RF boards. NOTE: Refer to the Flash Update Wizard s Help file for details on flashing the antenna. 3

4 Step 4 - Install New Satellites Now you need set up the system to track satellites compatible with the new LNB. This procedure varies according to your selected service configuration. Figure 7 Service Keys A B NOTE: If the TracVision system is equipped with service keys (see Figure 7), follow the steps in the Service Key Instructions to set up the TracVision system; if the TracVision system is equipped with an HDTV Control Panel or a Multi-Sat Control Panel (see Figure 8), follow the steps in the HDTV Control Panel/Multi-Sat Control Panel s User s Guide to set up the TracVision system. Option A - DIRECTV Ku-band HDTV a. If you need to track the DIRECTV 101, 110, and 119 satellites for Ku-band DIRECTV HDTV service, type the following Satinstall command then press Enter. SATINSTALL,TRISAT,DSS Figure 8 Multi-Sat Control Panel (MCP)/ HDTV Control Panel Figure 9 DISH 1000 Satellite Coverage Map b. Type ZAP then press Enter. c. The antenna will restart. = DISH 61 Satellite Recommended 4 Option B - DISH 1000 DISH 1000 setup varies by region. Refer to the map in Figure 9 to determine the appropriate DISH 1000 satellite installation for your region. a. Type the appropriate Satinstall command for your DISH 1000 setup, then press Enter. To track the DISH 110, 119 and 129 satellites: SATINSTALL,TRISAT,DISH To track the DISH 110, 119 and 61 satellites: SATINSTALL,TRISAT,DISH61 b. Type ZAP then press Enter to restart the antenna.

5 Option C - Alternate Satellites Although most installations do not require choosing different satellites than those listed in Option A - DIRECTV Ku-band HDTV or Option B - DISH 1000 on page 4, you can set up your TracVision system to track a pair of alternate satellites. Follow the steps below to configure the system to track satellites from the circular satellite library. a. Choose your desired satellites from the circular satellite library (see Figure 10). b. Type the following command then press Enter. Be sure to use your selected satellite s Install Names. An example is provided in Figure 11. SATINSTALL,<SAT_A_NAME>, <SAT_B_NAME> NOTE: Select the satellite you want to track first as SAT_A. Once the procedure is complete, the TracVision system will begin tracking that satellite. Figure 10 Circular Satellite Library Satellite DIRECTV 72 W DIRECTV 101 W DIRECTV 110 W DIRECTV 119 W DISH Network 61 W DISH Network 110 W DISH Network 119 W DISH Network 129 W ExpresssVu 82 W ExpressVu 91 W None Install Name DSS_72 DSS_101 DSS_110 DSS_119 ECHO_61 ECHO_110 ECHO_119 ECHO_129 EXPRESSVU EXPRESSTV None c. Type ZAP then press Enter to restart the antenna. The procedure is complete! Your TracVision system is now equipped with a circular (North American-type) LNB. Figure 11 Example of Circular Satellite Installation Installing DIRECTV 101 and DIRECTV 119 HALT SATINSTALL,DSS_101,DSS_119 ZAP 5

6 Changing from a Circular LNB to a Linear LNB The following steps explain how to change from a circular (North American-type) LNB to a linear (European-type) LNB. If you need to change from a linear LNB to a circular LNB, refer to Changing from a Linear LNB to a Circular LNB on page 2. Step 1 - Check for Flash Wizard Updates You need to check for flash file updates to ensure you have the most current software available (see Figure 12). Follow the Flash Update Wizard s onscreen instructions to check for updates. This procedure requires a PC with the latest version of the KVH Flash Update Wizard installed and an Internet connection. NOTE: Refer to the Flash Update Wizard s Help file for details on checking for updates. Step 2 - Flash Both Antenna Boards Connect a PC to your TracVision system, as described in the Flash Update Wizard s Help file. Then follow the Flash Update Wizard s onscreen instructions to flash the antenna s main and RF boards. NOTE: Refer to the Flash Update Wizard s Help file for details on flashing the antenna. Step 3 - Install New Satellites Follow the steps below to configure the system to track satellites from the linear satellite library. NOTE: If the TracVision system is equipped with service keys (see Figure 7 on page 4), be sure to remove the keys before proceeding; if the TracVision system is equipped with an Multi-Sat Control Panel (see Figure 8 on page 4), follow the steps in the Multi- Sat Control Panel s User s Guide to set up the TracVision system. a. Choose your desired satellites from the linear satellite library (see Figure 13). Figure 12 Check for Updates Option Figure 13 Linear Satellite Library Satellite Arabsat 26 E Astra 1 19 E Astra 2N 28 E Astra 2S 28 W Eutelsat W3A Hispasat 30 W Hotbird 13 E HotbirdWB 13 E Nilesat 101 PAS9 58 W Sirius 5 E Thor 8 W Turksat 1C 42 E None Install Name ARABSAT ASTRA1 ASTRA2N ASTRA2S EUTEL_W3A HISPASAT HOTBIRD HOTBIRDWB NILESAT PAS_9 SIRIUS THOR TURKSAT1C None 6

7 b. Type the following command then press Enter. Be sure to use your selected satellites Install Names. SATINSTALL,<SAT_A_NAME>, <SAT_B_NAME> Figure 14 European Position Grid NOTE: Select the satellite you want to track first as SAT_A. Once the procedure is complete, the TracVision system will begin tracking that satellite c. Type ZAP then press Enter to restart the antenna. Step 4 - Determine the Proper Skew Angle Use one of the following options to determine the skew angle for your location and selected satellites. Once you have obtained the skew angle, proceed to Change the LNB on page 8. Option A - Contact your service provider Your service provider can provide you with the correct skew angle for you selected satellite. Option B - Calculate the skew angle using a PC You can use a PC to determine the skew angle for any satellite in the linear satellite library. This procedure requires a PC with the latest version of the KVH Flash Update Wizard installed. TIP: The Flash Update Wizard is available to KVH - authorized dealers through the KVH Partner Portal. a. Using GPS or the map and table in Figure 14, determine your latitude and longitude. b. Type HALT then press Enter. c. Type DEBUGON then press Enter Grid # Latitude Longitude N 67 N 67 N 65 N 63 N 63 N 63 N 57 N 57 N 57 N 55 N 53 N 53 N 50 N 47 N 47 N 43 N 43 N 43 N 43 N 36 N 36 N 36 N 36 N 45 E 40 E 3 3 7

8 d. Using the table below, type the following command to enter your latitude and longitude. GPS,XX,D,YYY,F Figure 15 Radome Screws/LNB Types Radome Variable Value XX latitude (0-90) Screw and Washer (x8) D (Enter N or S) N (North) S (South) YYY longitude (0-180) W (West) F (Enter W or E) E (East) Baseplate e. Type SKEWANGLE then press Enter to display the skew angle for your location and satellites. Step 5 - Change the LNB CAUTION Circular LNB Linear LNB For your own safety, be sure to disconnect power from all wired components before performing this procedure. a. Disconnect power from the TracVision system and any connected receivers and/or multiswitch. b. Remove the eight screws securing the radome (see Figure 15). Then remove the radome and set it aside in a safe place. c. Using a 7/16" open-end wrench, disconnect the RF cable from the bottom RF connector on the LNB. d. Using a supplied tie-wrap, secure the disconnected RF cable to the reflector arm, as shown in Figure 16. Ensure that there are no sharp bends in the cable. e. Disconnect the RF cable from the top RF connector on the LNB (see Figure 16). Figure 16 LNB Connectors and RF Cables RF Cable Center Tie-wrap Top RF Connector 8

9 f. Attach the supplied skew arrow label to the LNB bracket as shown in Figure 17. Be sure to center the label between the allen screws. g. Using a 9/64" allen wrench, remove the two LNB bracket screws and washers securing the LNB (see Figure 17). h. Carefully expand the LNB bracket just wide enough to lift the LNB from the LNB bracket. Remove the LNB. i. Note the location of the linear LNB components in Figure 18. You will need to reposition the LNB relative to these components. j. Place the linear LNB into the LNB bracket. Orient the LNB as shown in Figure 19. Insert the new washers and allen screws supplied in the kitpack into the LNB bracket, then handtighten both LNB bracket screws. Be sure to alternate the tightening of the screws to maintain a balanced grip on the LNB. NOTE: Be sure to use the allen screws supplied in the kitpack to secure the linear LNB. The linear LNB requires longer allen screws. k. Verify that the LNB bracket screws are aligned with the adapter sleeve screw bevels and that the tie-wrap is positioned outside the LNB bracket (see Figure 18 and Figure 19). Figure 17 Skew Arrow Label Screws and Washers Figure 18 Linear LNB Components Adapter Sleeve LNB Tie-wrap Figure 19 LNB Orientation (Top View) SKEW SKEW Screw Bevel Screws Tie-wrap 9

10 Step 6 - Set the Skew Angle Follow the steps below adjust the skew angle for proper satellite reception. Figure 20 Skew Arrow Alignment -20 Skew a. Rotate the LNB to align the skew arrow with the skew angle you determined in Determine the Proper Skew Angle on page 7 (see Figure 20). b. Using a 9/64" allen wrench, tighten the LNB bracket screws securing the LNB in the following manner: tighten one screw one full turn, then tighten the second screw one full turn; repeat until the LNB no longer rotates freely. Negative Skews SKEW Positive Skews c. Turn the screws one additional 1/4 turn. d. Reinstall the radome using the eight screws and washers you removed in Step 5b. on page 8. e. Restore power to the TracVision system. The procedure is complete! Your TracVision system is now equipped with a linear (Europeantype) LNB. 10