PHABLABS 4.0 Gobo Batman/Slide projector
|
|
- Garry Watson
- 5 years ago
- Views:
Transcription
1 PHABLABS 4.0 Gobo Batman/Slide projector Title of the workshop: The Gobo Batman/Slide projector Target audience: 14 /16? Time planning: Part 1 (15 min), part 2 (15 min), part 3 (5 min). Estimated cost: 9.06
2 Step 1 Title: Gobo workshop The working of optical system based on lenses is explained during this workshop. Two lenses are used to make a slide projector. The first lens is to make the divergent light coming from the led into parallel light (collimation). This done to make sure the slide gets enough light evenly distributed over the slide. Figure 1 shows the lens system that is used in the Gobo slide projector. Figure 1: Optical system of the Gobo slide projector As you can see in Figure 2 the first lens should be place with the flat side towards the LED to make the divergent light parallel. The second lens should be placed with the flat side towards the slide to make the enlargement of the image possible. Figure 2: Ray of light going thought a plano-convex lens (left); Picture of the lee and the holders used in the project (right)
3 Step 2: Part list Listed below are the parts that are used to make the Gobo projector. In figure 5 the electrical and photonic components are displayed. Construct the electronical and photonic components first before you begin with the construction of the Gobo projector. Photonics parts For the optical part, we will only use a spherical plano-convex lens with the following specifications. Name Diameter Effective diameter Focal length Dioptre Form Lens 34.5 mm 30.0 mm mm +4.4 Spherical Figure 3: Picture of the spherical lens in use Electronic parts: We would need a bright source of light, an electronic control, a switch and a battery: 11 volts LED DC-to-DC converter (3 to 30V) USB cable Electric cables USB power bank
4 Figure 4: Electric components needed (USB power bank, DC-DC converter and LED) Other parts: To make the collimator and the frame, we will need: PVC tube wooden plates. Step 3: Building some blocks Collimator A collimator is needed to collimate the light that is coming from the LED. In Figure 3 there are two rings displayed; take some glue and attach these two circles to each other. Take the PVC tube and place aluminium tape of the inside of the tube, with the help of a pencil. Take the PVC tube and a hammer to take the tube inside of the circle. a b c d Figure 5: a, b, c, d
5 LED First ensemble the electronical and electrical parts before you start with the Construction of the Gobo projector. Take the DC-to-DC converter and solid the red wire to Vin+ and a black wire on Vin-,do this also the Vout+ and Vout-.. Solid the red wire to the plus of the LED and the black to the minus of the LED when you have ensemble the DC-to-DC converter.
6 Step 3: Assembly of the Gobo Step 0: The Gobo projector is divided into three parts and will be construct in three parts. The figure below shows the final product with each part indicated. Figure 6: the 3 different parts to make the Gobo Step 1: print the Gobo projector with the laser printer and lay them out as shown in picture 1. The construction of the Gobo projector is guided by a code. This code can be found on each component, Figure 7 show the available codes. The projector is divided in three sections.
7 Figure 7: the coding system used during the Construction of the Gobo projector. A) shows the pentagram code, b) shows the circle code and c show the triangle. Step 2: The first part of the Gobo projector will be constructed out of the circle components. Sort out all the component with the circle and put them together, as shown in figure 8.
8 Figure 8: overview of the part for the First part of construction. Step 3: In Figure 10 you can see the four plates, take three plates two without print and one with print. Place the plates as shown in figure 11a and 11b. Place the final plate to make an open box as shown in figure 5 Place the lens on the top of the box the finish the first part of the Gobo projector. If all the steps are followed correctly the first of the Gobo looks like
9 Figure 9 : The Construction of the First part, a) top view, b) side view Figure 10: the First part with the top part attached (left) the finished part (right) Part 2
10 Step 4: The first part of the Gobo projector is finished, to start with the second part sort out all the components with a triangle engraved on them. The small components on the left top side are going to be used to hold a slide. Figure 11: the part needed for the second part step 5: Take the two plates with the holes in them and the small components to hold the slide. Place them as shown in the Figure 15. Take the only Blanco plate and place it as shown in Figure 16 and Figure 17.
11 a b c Figure 12: The slide holder system (a), first plate attached to the slide holder system (b) and second slide holder attached to the previous plates (c)
12 Step 6: Take the handle that you have constructed before and place the handle as shown in Figure 18. Take the first lens and place it in front of the slide holders with the flat side towards the lens. Take the final plate with the ruler engraved and insert it on the only place that is left. Figure 18 shows the last step to finish the last part. Figure 13: the lens is place in the second part of the Gobo construction Step 6: The last part of the Gobo projector is the handle. Take the remaining parts and place them as shown in Figure 19. Figure 14: Steps for the construction of the Gobo handle
13 End product Congratulation you have now a final Gobo projector that allow you to use your grand-pa slide or make your own design to project your sign as Batman does Figure 15: Final Gobo Projector
14 PHABLABS 4.0 is a European project where two major trends are combined into one powerful and ambitious innovation pathway for digitization of European industry: On the one hand the growing awareness of photonics as an important innovation driver and a key enabling technology towards a better society, and on the other hand the exploding network of vibrant Fab Labs where next-generation practical skills-based learning using KETs is core but where photonics is currently lacking. This workshop was set up by the Department of Imaging Physics at TU Delft in close collaboration with Science Centre Delft.
USER MANUAL FOR THE PANEL VIEWER
Ing. J. de Wijs. Populierstraat 44, 4131 AR Vianen, the Netherlands Tel/Fax. +31 (0)347-372242 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com Design and production of stereoscopic instruments. Bank:
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual REV
REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationBionic Elephant Trunk. Assembly Instructions
Bionic Elephant Trunk Assembly Instructions Equipment and Supplies Required items from the Bionics Kit and/or Materials Pack: 1. Tail fin (small) assembled 2 see Start Here for tail fin assembly instructions
More informationWaterVue TV Installation & User Manual
WaterVue TV Installation & User Manual 19 Waterproof TV Dimensions of TV Front screen 486mm x 340mm x 3mm Mounting Plate 467mm x 324mm x 48mm 24 Waterproof TV Dimensions of TV Front screen 576mm x 395mm
More informationSpecifications. Mechanical Information. Mass (grams) Dimensions (mm) 15 x 75 Housing. Anodised Aluminium Isolated Body
Beta TX Datasheet Beta-TX The Beta-TX is a complete self contained laser diode system which can operate in both CW and modulation modes. The Beta- TX features high speed modulation with a bandwidth of
More informationMP Maker Pro Mk.1. Quick Start Guide
MP Maker Pro Mk.1 P/N 33013 Quick Start Guide ONLINE SUPPORT Monoprice is pleased to provide free online support. For order related issues, contact the Customer Service department through the Live Chat
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationCable System Installation Guide
Overview Cable System Installation Guide 5/19/2008 Our recommended approach for the installation of your Circle Graphics Cable Systems on the panels in your market is to install the fixed hardware (namely
More informationObtained from Omarshauntedtrail.com
http://www.cindybob.com/halloween/ledlighting/ledspotlights/ Introduction In our 2005 haunt providing 120V AC power to the various lights and props requiring it became a fairly large problem. Extension
More informationLED Panel Light. Specialists. in High Efficiency Lighting DLC 4.0
LED Panel Light Specialists in High Efficiency Lighting DLC 4.0 E485145 E485145 Dimmable Optional Same cost for dimmable or non dimmable lamps, as same design products can help to reduce product categories
More informationFIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
More informationM2-Measurement Report
Fraunhofer Institute for Laser Technology ILT Steinbachstraße 15 52074 Aachen Tel. 0241 8906 0 www.ilt.fraunhofer.de Aachen, July 29 th 2016 201901 DIVERSE OE 131 Industriekleinprojekte Authors: Dr. rer.
More informationMonday 20 May 2013 Afternoon
Monday 2 May 213 Afternoon AS GCE PHYSICS B (ADVANCING PHYSICS) G491/1 Physics in Action *G4122613* Candidates answer on the Question Paper. OCR supplied materials: Data, Formulae and Relationships Booklet
More informationGETTING STARTED... 2 ENVIRONMENT SCAN... 2
Sputnik User Manual GETTING STARTED... 2 SPUTNIK OVERVIEW... 2 ENVIRONMENT SCAN... 2 SETTING UP SPUTNIK... 2 CONDUCTING AN ENVIRONMENT SCAN... 3 ENVIRONMENT SCAN RESULTS... 3 1 GETTING STARTED Sputnik
More informationMOD028 GLOCKENSPIEL TECHNO-MUSIC-OLOGY
MOD028 GLOCKENSPIEL TECHNO-MUSIC-OLOGY MOD028 - Techno-music-ology Kit Contents Motor Controller PCBs 14 220R (red red brown gold) resistors 2 330R (orange orange brown gold) resistors 16 1N4001 diodes
More informationInkscape/Laser Cutter Fab Lab Project (100 Points) PART 1 25 points, PART 2 25 points, PART 3 25 points, Part 4 25 points YOU CAN WORK WITH A PARTNER
Inkscape/Laser Cutter Fab Lab Project (100 Points) PART 1 25 points, PART 2 25 points, PART 3 25 points, Part 4 25 points OBJECTIVE: Design a smart device (phone or tablet) tabletop holder in Inkscape
More informationMAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION
MAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION Part Number: D99821002 Rev 212 MAY 2017 REGISTERED TO ISO 9001:2008 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301
More informationDisplay Systems. Viewing Images Rochester Institute of Technology
Display Systems Viewing Images 1999 Rochester Institute of Technology In This Section... We will explore how display systems work. Cathode Ray Tube Television Computer Monitor Flat Panel Display Liquid
More information5.2.3 Fibre Optic Rod 1 PARTNERS: Purpose: To replicate how light behaves in fibre optic cables by using a laser light and a solid acrylic rod.
5.2.3 Fibre Optic Rod 1 NAME: DATE: PARTNERS: Purpose: Materials: To replicate how light behaves in fibre optic cables by using a laser light and a solid acrylic rod. 1. Acrylic rod 2. Laser pointer 3.
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More informationThe Haply Development Kit
The Haply Development Kit Introduction The Haply development kit is a robust and adaptable open-source hardware development platform for haptic applications. Designed to be accessible to novices and experts
More informationENGINEERING COMMITTEE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 31 2016 Test Method for Measuring Diameter Over Core Title Table of Contents Page Number Table of Contents 2
More informationPowerBook G4 Aluminum 12" GHz LCD panel upgrade
PowerBook G4 Aluminum 12" 1-1.5 GHz LCD panel upgrade Upgrade a 1400x1050 LCD panel. Written By: martin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The original LCD 1024x768 resolution
More informationSetup Guide. Read me BefoRe unpacking!
Setup Guide Read me BefoRe unpacking! Package Contents In The Replicator package The Replicator SD card (in The Replicator SD card slot) In the Accessory Box found within The Replicator frame Single or
More informationSpatial Response of Photon Detectors used in the Focusing DIRC prototype
Spatial Response of Photon Detectors used in the Focusing DIRC prototype C. Field, T. Hadig, David W.G.S. Leith, G. Mazaheri, B. Ratcliff, J. Schwiening, J. Uher, J. Va vra SLAC 11/26/04 Presented by J.
More informationA dedicated data acquisition system for ion velocity measurements of laser produced plasmas
A dedicated data acquisition system for ion velocity measurements of laser produced plasmas N Sreedhar, S Nigam, Y B S R Prasad, V K Senecha & C P Navathe Laser Plasma Division, Centre for Advanced Technology,
More informationOperating instructions Retro-reflective sensor. OJ50xx laser / / 2010
Operating instructions Retro-reflective sensor OJ50xx laser 70481 / 00 05 / 010 Contents 1 Preliminary note3 1.1 Symbols used 3 Safety instructions 3 4 Installation 4 4.1 Installation of the supplied mounting
More informationProduct information. Front-door station series with video for surface-mount
Product information Front-door station series with video for surface-mount series VPES series VPDS 2 05/2006 Table of contents Scope of delivery...3 Safety notices...3 General notes on the cabling in TCS
More informationTeltron Delection Tube D
Teltron Delection Tube D 1011119 Overview The electron-beam deflection tube is intended for investigating the deflection of electron beams in electrical and magnetic fields. It can be used to estimate
More informationAdapter Selection. Entry Size (Continued) Table E. Multiplication. factors for wire bundles. with Equal Size Wires. This table provides multiplication
Table E. Multiplication Factors for Wire Bundles with Equal Size Wires This table provides multiplication factors for wire bundles of to 6 wires. To determine the approximate diameter of a wire bundle
More informationManual placement system MPL3100. for BGA, CSP and Fine-Pitch components
Manual placement system MPL3100 for BGA, CSP and Fine-Pitch components Part No: MPL3100BA1.0e Issue Date: 02/2001 You have opted for an ESSEMTEC MPL3100 pick and place system. We thank you for this decision
More informationOSTAR -Lighting. OSTAR -Lighting / OS LED M / SS 25/01/2006 Page: 1
/ OS LED M / SS 25/01/2006 Page: 1 Overview slides: Possible applications Customer benefits Product features Technical data Driver recommendations Application example OSTAR platform roadmap / OS LED M
More informationREAD THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
06.18.18 BEFORE YOU BEGIN Determine your light bar mounting method. Are you using pre-existing sockets to mount? If so, Retrofit Connectors are included. If not, be sure to purchase our Speed Spring Brackets
More informationReference Manual. Notes 9/16 Series H
Reference Manual Notes 9/16 Series 173.01H Copyright notice The information in this document is subject to change without prior notice and does not represent a commitment on the part of Q-MATIC AB. All
More informationapple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple
More informationVisit for complete specifications on every Senior Industries product.
Switches Switch models include: slide, toggle, rocker, pushbutton, tactile, power rocker, dip and dip pushbutton. Switches are available in a variety of styles including upright, right angle, pc mount,
More informationCold Shrink Straight Joint
Cold Shrink Straight Joint 3M QS2000E 22 kv Single Core Straight Joint Instruction Sheet All dimensions shown are in mm unless otherwise stated Kits contains components for one single core cable -2-2*
More informationCambridge International Examinations Cambridge International General Certificate of Secondary Education
Cambridge International Examinations Cambridge International General Certificate of Secondary Education *3304382220* COMPUTER SCIENCE 0478/12 Paper 1 Theory May/June 2016 1 hour 45 minutes Candidates answer
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual. ver 3.0.
ver 3.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationOPTICAL POWER METER WITH SMART DETECTOR HEAD
OPTICAL POWER METER WITH SMART DETECTOR HEAD Features Fast response (over 1000 readouts/s) Wavelengths: 440 to 900 nm for visible (VIS) and 800 to 1700 nm for infrared (IR) NIST traceable Built-in attenuator
More informationHigh intensity led illuminator ILED42A FEATURES: DESCRIPTION: ELECTRICAL CHARACTERISTICS:
High intensity led illuminator May 2010 Rev 0.3 ILED42A FEATURES: High luminous flux Low cost Fully protected Wide input voltage range Available with different led colours and lenses DESCRIPTION: The IDP
More informationF7000NV ROBOT VISION OPERATING MANUAL
Rev. C Feb 2012 F7000NV ROBOT VISION OPERATING MANUAL Rev. C Feb 2012 This page has intentionally been left blank. Contents Contents Chapter 1. Getting Started... 5 1. Preface... 5 2. Manuals... 5 3. Setting
More informationDissolve Control Programming : Projector/Dissolve Control Hook-Up
Product Information Title: Operating Equipment: Dissolve Control Programming Projector/Dissolve Control Hook-up Sync Track Hook-up Converting Tapes to Digital Sync Signals Recording Signals 80 Vs 140 Slide
More informationAzatrax Model Railroad Track Signal Control - Single Track
Installation Guide Azatrax Model Railroad Track Signal Control - Single Track TS2 What it is: The TS2 operates one or two trackside block signals (one in each direction) on one track to simulate the block
More informationMedium Box for Cable Termination
FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling
More informationLensed Fibers & Tapered Ends Description:
Lensed Fibers & Tapered Ends Description: LaseOptics Corporation ( LaseOptics ) has been producing next generation optical lensed fibers. LaseOptics Lensed Optical Fibers technology is proprietary integrated
More informationepos & Security Essentials Trade ONLY ONLY Trade Catalogue Call us Now on Visit Our Website
epos & Security Essentials Trade Catalogue Trade ONLY ONLY Call us Now on 024 7668 8590 Visit Our Website www.tronicextreme.co.uk 2 Item No. 10595 Item No. 10596 TP-101 All in One Touch Screen epos System
More informationQuick set up guide. Leaders in learning technology
Quick set up guide Leaders in learning technology Quick set up guide for Genee Vision 2100 visualiser Quick guide contents Now that you have received your visualiser you will want to get started straight
More informationUSER MANUEL. SNIPE 2 Ref R13
USER MANUEL SNIPE 2 Ref. 0141317R13 Contents 1. General Information 1-1. Introduction 1-2. Proper use and operation 1-3. Safety notes......... 2 3 3 2. Contents 2-1. Accessory included 2-2. Name of parts......
More informationFIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays
FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and
More informationUser manual for: Digital 3D viewer for panel mount Model D50-x
de Wijs apparatenbouw Vleugelboot 68, 3991CL, Houten the Netherlands Tel. +31 (0)30-6364928 Fax. +31 (0)30-6361723 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com User manual for: Digital 3D viewer
More informationHome Cinema LCD Projector with 4K Enhancement and HDR
Home Cinema 4000 3LCD Projector with 4K Enhancement and HDR Contact Us 800.463.7766 Mon-Fri 6am-8pm, Sat 7am-4pm PT The elite 4Ke home theater projector that brings color to life. The Home Cinema 4000
More information3. Electronics and MMU2 unit assembly
Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 34 Step 1 Tools necessary for this chapter Please prepare tools for this chapter: 2.5mm Allen key for M3 screws 2mm Allen key for nut alignment
More informationDissolved Oxygen Transmitter
3 YEAR SENSOR WARRANTY 5.4 We reserve the right to continuously improve our products and make any change in the stated specifications and dimensions without prior notice. General MJK Oxix s are designed
More informationJACK Digital HDTV Over-the-Air Antenna
JACK Digital HDTV Over-the-Air Antenna w/built-in SureLock Digital TV Signal Meter TM OA8200-White OA8201-Black SPECIFICATIONS Dimensions: 11.25 H x 16 W x 12.5 L Powered Amplifier +12 volt / 100 ma working
More information3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes
FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Parts in the box Single monitor Dual monitor M2 M8 M/Flex + (package contents will depend on configuration ordered) Tools required for installation 6.0 mm Hex Key
More informationSN-Class Nixie Clock Kits
Assembly Instructions And User Guide SN-Class Nixie Clock Kits - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 20 November 2017 New document - 2 - 1. INTRODUCTION 1.1 About the How can the
More informationeasydelta BUILD MANUAL easydelta 3D printer design & documentation by Achatz Industries Haefland 8A 6441 PA Brunssum The Netherlands
easydelta BUILD MANUAL easydelta 3D printer design & documentation by Achatz Industries Haefland 8A 6441 PA Brunssum The Netherlands BUILD MANUAL Welcome to the 1. Edition Build Manual for your easydelta
More informationCANNON STANDARD page 1 of 18. Cm5 MOTOR CONNECTOR
CANNON STANDARD page 1 of 18 1 General Information... 2 1.1 Scope... 2 2 Ordering Code... 3 2.1 Housing / Motor Side... 3 2.2 Cable Side... 3 3 Explosion Drawing... 3.1 Explosion Complete Assembly... 3.2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BEFORE INSTALLING OR ADJUSTING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY. PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE FIBER OPTIC SWING-OUT PATCH PANEL INSTRUCTION
More informationPRODUCT GUIDE CEL5500 LIGHT ENGINE. World Leader in DLP Light Exploration. A TyRex Technology Family Company
A TyRex Technology Family Company CEL5500 LIGHT ENGINE PRODUCT GUIDE World Leader in DLP Light Exploration Digital Light Innovations (512) 617-4700 dlinnovations.com CEL5500 Light Engine The CEL5500 Compact
More informationElectronic Equipment Manual For 101, 102, 301 & 302 Azrieli Theatre For further information, please visit our website at:
Electronic Equipment Manual For 101, 102, 301 & 302 Azrieli Theatre For further information, please visit our website at: http://www.carleton.ca/ims/ 2 TABLE OF CONTENTS: Topic Page # Logging onto the
More informationINSTALLATION INSTRUCTION PEM1423ENG ENGLISH
INSTALLATION INSTRUCTION PEM1423ENG 2013-03 ENGLISH COLD SHRINK JOINT CJ11.242 FOR SINGLE CORE CABLES WITH Cu WIRE SHIELD Uo/U = 12.7/22 kv, Um = 24 kv 2/10 CJ11.242 PEM1423ENG 2013-03 GENERAL INFORMATION
More informationInstruction Manual. from software version 1.0 (instruction version 1.3) Internet:
Instruction Manual from software version 1.0 (instruction version 1.3) email: service@glp.de Internet: http://www.glp.de GLP German Light Production (V1.3) 1 Table of contents 1 Description of Device...
More informationSeth h N eu N mann 1
Seth Neumann sneumann@pacbell.net 1 Why Control Panels? Panels work well where you have a group of related indicators and controls close together Panels may not be the right answer for all fascia controls:
More informationGrowmaster Assembly Instructions
Growmaster ssembly Instructions Item No. Part Sect. Ref. Size mm Quantity Item No. Part Sect. Ref. Size mm Quantity 1001 15 M6 x 12 86x 97x 108x 1067 6 295 16 M6 9 10 113x 1301 7 30 9x 1 13x 5 7 3.5 x
More information2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table
FIST-GCO2-F INSTALLATION INSTRUCTION GCO2-FC GCO2-FD Content 1 Introduction 2 General 2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table 3 Installation
More informationPlexBright LED Optogenetic Stimulation System
PlexBright LED Optogenetic Stimulation System Introduction Laser-based light sources were the first to make inroads in in vivo optogenetic experimentation, due to their capability of delivering high levels
More informationThe Two Assemblies. Standard Assembly For signs up to 11" wide. Pull flexible lens directly outward with Sucton Cup Tool for lens removal
System Overview The Two Assemblies The Arris system is comprised of two unique assemblies, each designed to provide maximum cost effectiveness and design flexibility for specific types of signs. With both
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More informationService Call: Fiber Optic Installation and Repair
Service Call: Fiber Optic Installation and Repair Tools Required: Tools available from www.bohlinger.biz Cable: Terex P/N 453830 Stripper Block: P/N 65-020-01 Termination Block: P/N 65-020-02 Utility Knife
More informationScreens; media that use additive primaries
Image display Display is the final stage in the image processing pipeline: Continuous scenes are acquired and digitally processed. The display process essentially converts the discrete image back to continuous
More informationInstructions for Use: Video Inspection Scope with Display
Instructions for Use: Video Inspection Scope with Display Brand Name of Product Video Inspection Scope Generic Name of Product Video Inspection Scope Product Code Number(s) FIS-004 Intended Use For visually
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationPROCEEDINGS OF SPIE. Volumetric, dashboard-mounted augmented display
PROCEEDINGS OF SPIE SPIEDigitalLibrary.org/conference-proceedings-of-spie Volumetric, dashboard-mounted augmented display David Kessler, Christopher Grabowski David Kessler, Christopher Grabowski, "Volumetric,
More informationSONOSAX SX-PR OPERATOR'S MANUAL
SONOSAX SX-PR OPERATOR'S MANUAL Manual copyright 1989 - Gary J. Louie Sonosax is a trademark of Jacques Sax Edition 2.1 OVERVIEW The Sonosax SX-PR series portable stereo audio mixers are designed for jobs
More informationAC335A. VGA-Video Ultimate Plus BLACK BOX Back Panel View. Remote Control. Side View MOUSE DC IN OVERLAY
AC335A BLACK BOX 724-746-5500 VGA-Video Ultimate Plus Position OVERLAY MIX POWER FREEZE ZOOM NTSC/PAL SIZE GENLOCK POWER DC IN MOUSE MIC IN AUDIO OUT VGA IN/OUT (MAC) Remote Control Back Panel View RGB
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
More informationParts of dicing machines for scribing or scoring semiconductor wafers , , , , ,
US-Rev3 26 March 1997 With respect to any product described in or for Attachment B to the Annex to the Ministerial Declaration on Trade in Information Technology Products (WT/MIN(96)/16), to the extent
More informationGAP SUPER C ANTENNA. Installation and Assembly Instructions. GAP Antenna Products, Inc. 99 North Willow St Fellsmere, FL (561)
GAP SUPER C ANTENNA Installation and Assembly Instructions GAP Antenna Products, Inc 99 North Willow St Fellsmere, FL 32948 (561) 571-9922 WEBSITE http://www.gapantenna.com SAFETY NOTICE WARNING POWER
More informationOwner s Manual PRE1. v1.2. Triode Class A Line Preamplifier
Owner s Manual PRE1 Triode Class A Line Preamplifier www.lab12.gr v1.2 Table of Contents It is yours Features Installation & Placement Front Panel Rear Panel Remote Control Main connections For the safety
More informationRocket Kit #1. Illuminated Display Model. Zifnu Electronics LLC.
Rocket Kit #1 Illuminated Display Model Congratulations on your purchase of the Zifnu Rocket Kit #1, an open-source RGB LED illuminated static display model that is intended to provide some insight into
More informationConference Speaker Timing System. Operating Instruction Manual
Conference Speaker Timing System Operating Instruction Manual December 2006 Table of Contents Overview... 2 The Master Station... 2 The Slave Station... 2 Warning Lights... 3 Radio-Controlled Clock...
More informationSTAR-07 RGB MULTI-COLOR INDUSTRIAL PATTERN PROJECTION
STAR-07 RGB MULTI-COLOR INDUSTRIAL PATTERN PROJECTION STAR-07 RGB is a high performance DLP projector based upon the Texas Instruments micromirror technology and designed to serve in demanding industrial
More informationINPUT OUTPUT GAIN DELAY. Hue Candela Strobe Controller. Hue Candela s STROBE CONTROLLER. Front Panel Actual Size 7 ¼ By 4 ¾ POWER. msec SEC 10 1.
Hue Candela s STROBE CONTROLLER INPUT OUTPUT ON TIME POWER NO B C A GAIN X LOCK Y OUT Z Hue Candela Strobe Controller 4 5 6 7..... 8. 3. 9. 2 10.. 1 11. STEP m.. 0 10 1. 10 10 1.0 10 zero DELAY. 03. 02.
More informationConnecting cables NEBS, for sensors
Connecting cables NEBS, for sensors Connecting cables NEBS, for sensors Product range overview Function Version Type code Connection technology (Electrical connection 2) Connecting cable Cable characteristic
More informationLED Flexible strip. Specification UCS1903 LED STRIP. Product Name HTD-1903XX-X. Product Number V1.0. Version Number. Page
LED Flexible strip Specification Product Name Product Number Version Number Page UCS1903 LED STRIP HTD-1903XX-X V1.0 9 Product description UCS1903 LED Strip use the FPCB ( flexible printed circuit board)
More informationGB-ER series. Direct connection to LH70/71 series
GB-ER series Direct connection to LH70/71 series 21/12/2007 Product comparison GB-A series Cable length : 3m, 5m, 10m Waterproof connector CH01 Multi-gap head PM output Up/Down output GB-ER series Cable
More informationCambridge International Examinations Cambridge International General Certificate of Secondary Education
www.xtremepapers.com Cambridge International Examinations Cambridge International General Certificate of Secondary Education *5619870491* COMPUTER SCIENCE 0478/11 Paper 1 Theory May/June 2015 1 hour 45
More informationSJOF-BS604B. Fiber Optic Splice Closure User Manual Rev.1
Fiber Optic Splice Closure 1. Introduction 1.1 General SAMJIN s SJOF-BS604B protects fiber optic splicing point in various installation conditions such as aerial, manholes, ducts, wall and direct buried
More informationusing the Scott A Speakman, Ph.D Center for Materials Science and Engineering at MIT
X-Ray Reflectivity using the PANalytical X Pert Pro MPD Scott A Speakman, Ph.D Center for Materials Science and Engineering at MIT http://prism.mit.edu/xray Modified for configuration used at University
More informationQuick Start Guide Long Range Wireless 5x2 HDMI Matrix PRO Receiver
Quick Start Guide Long Range Wireless 5x2 HDMI Matrix PRO Receiver GWHDRX01 PART NO. Q1286-a www.iogear.com Package Contents 1 x Long Range Wireless 5x2 HDMI Matrix PRO Receiver 1 x Remote Control 1 x
More informationNon Magnetic Connectors
Non Magnetic Connectors Johnson Components builds coaxial connectors using innovative materials and design to provide Mil Spec Performance at a commercial price. Now we offer our Non Magnetic Connectors
More informationimac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement
imac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement The CCFL back lights are replaceable. I have pulled mine apart and documented my method. '''NOTE''' This is not for the feint hearted!
More informationINSTALLATION GUIDE DYNAMIC TRIM CONTROL SYSTEM SERIES S
INSTALLATION GUIDE DYNAMIC TRIM CONTROL SYSTEM SERIES S Drill bits TOOLS Power drill Ø Ø Ø Ø Ø 2.5 mm (3/32 ) 3 mm (1/8 ) 3.5 mm (9/64 ) 4 mm (5/32 ) 5 mm (3/16 ) Sealant Hole saw Screw bits Ø 76 mm (3
More informationBill of Materials: Magic Color PART NO
Magic Color PART NO. 2193838 Magic color is a guessing game. With this game you can surprise your friends and leave them with amazement, how the game guesses what they have in their minds. Only two selections
More informationDIAS power supply and DIC 221 fibre optic cable coupling module
POWER SUPPLY AND FIBRE OPTIC COUPLING MODULE DIC 221 DIAS power supply and DIC 221 fibre optic cable coupling module for the power supply of DIAS function modules, 2 x fibre optic cable connections (DIAS
More informationFurcation of a Central Tube Ribbon, Gel-Free, Non-Armored, 96- to 192-Fiber Cable into an OSE-UD
Furcation of a Central Tube Ribbon, Gel-Free, Non-Armored, 96- to 192-Fiber Cable into an OSE-UD P/N 004-277-AEN Issue 1 related literature Search www.corning.com/opcomm. Click on Resources. 1. Initial
More information