TVS-2-VX. High Level Hopping Code Scrambler for Vertex Radios VPU-15-VX. Voice Inversion Scrambler with Kryptic Signaling for Vertex Radios

Transcription

1 TVS--VX High Level Hopping Code Scrambler for Vertex Radios VPU--VX Voice Inversion Scrambler with Kryptic Signaling for Vertex Radios Manual Revision: 0--0 Covers Software Revisions: TVS--VX:.9 & Higher VPU--VX:.9 & Higher Covers Hardware Revisions: F & Higher This manual & product supports the following Vertex radios: Portables: VX-0, VX-0, VX-0, VX-0-VX-0, VX-00, VX-00, VX-0, VX-900, VX-90 Mobiles: VX-00, VX-00, VX-000, VX-00, VX-00, VX-00, VX-00, VX-00, VX-000

2 SPECIFICATIONS Operating Voltage Operating Current Operating Temperature Frequency Response Input Impedance Carrier Suppression. VDC ma C Hz > k db < Peak Voice Encryption Specifications TVS-: Encryption Sequences TVS-: Random Number Generator TVS-: Sequence Length (est.) +0 Trillion bits billion years VPU-: Inversion Codes Available INSTALLATION OVERVIEW. Test the radio for functionality.. Program the scrambler per the Product Programming Section of this manual.. Install the scrambler into the radio per the Hardware Installation Section of this manual.. Program the radio per the Radio Programming Section of this manual. *** Midian is not responsible for any damage/loss resulting from the use of Midian s products. TVS- Series: GENERAL INFORMATION The TVS- series is a high-level hopping code scrambler. The TVS- uses hopping type rolling code encryption for higher security rather than sweeping code type and offers user-programmable hop rates and is down gradable to voice inversion. The scrambler is capable of features such as ANI, ENI, OTAR, Deadbeat Disable, Spy, and more when using Midian s Kryptic Signaling format with the CAD-00/DDU-00/TRC-00. For more information on the TVS- please read the TVS- Technical Reference Manual. Note: The TVS--VX by Midian is the same module as the FVP- sold by Vertex Standard (Yaesu). VPU- Series: The VPU- series is an entry level voice inversion scrambler with Midian s Kryptic Signaling. The scrambler is capable of features such as ANI, ENI, OTAR, Deadbeat Disable, Spy, and more when using Midian s Kryptic Signaling format with the CAD-00/DDU-00/TRC-00.

3 PRODUCT PROGRAMMING Midian s TVS--VX and VPU--VX are programmed via Midian s KL- programming interface and the MPS software. Please reference the KL- manual for setup instructions of the software and hardware. From the product selection screen on the MPS software, select the TVS--VX or VPU--VX from the list and click OK. Set the parameters of the scrambler software to fit the application. If any clarifications on a feature are required, move the mouse cursor over the feature name until the question mark appears and right click, a definition of the feature will be shown. After entering the parameters, save the file by going to File - Save As. Enter the file name in the File Name block and click Save. Saving the file will allow for quick and easy reprogramming of units. Programming: Plug the board onto the KL- and connect the green clip lead to the Program In hole. Push the power button on the KL- and click Program Unit in the MPS software. The LED on the KL- will faintly flash if programmed successfully. Reading: Plug the board onto the KL-, connect the green clip lead to the Program In hole, and connect the yellow clip lead to the Program Out hole. Push the power button on the KL- and click Read Unit in the MPS software. NOTE: When the scrambler is read, the security codes will be read out as zeroes. If another scrambler is then cloned with this information, the scramblers will be incompatible because they have different security codes. Program Out Program In

4 HARDWARE INSTALLATION Be certain to follow standard anti-static procedures when handling any of Midian s products. VX-0: Remove the battery, exposing the option board cover and remove the cover. Plug the scrambler onto the options connector. Replace the option board cover and battery. The scrambler requires this radio have firmware version.0 or higher. VX-0 & VX-0: Remove the battery, exposing the option board cover and remove the cover. Remove the dummy board from the radio and replace with the scrambler. Replace the option board cover and battery. The scrambler requires this radio have firmware version.0 or higher. VX-0 & VX-0: Remove the battery, exposing the option board cover and remove the cover. Plug the scrambler onto the Options Connector. Replace the option board cover and battery. The scrambler has been tested in firmware version VX-00 & VX-900: Remove the battery, exposing the option board cover and remove the cover. Remove the dummy board from the radio and replace with the scrambler. Replace the option board cover and battery. The scrambler requires this radio have firmware version. or higher. VX-00: Remove the battery, exposing the option board cover and remove the cover. Remove the dummy board from the radio and replace with the scrambler. Replace the option board cover and battery. The scrambler requires this radio have firmware version. or higher. VX-0/90: Remove the battery, exposing the option board cover and remove the cover. Plug the scrambler onto the options connector. Replace the option board cover and battery. The scrambler requires this radio have firmware version.9 or higher. VX-00/VX-00: Remove the cover of the radio exposing the options connector. Plug the scrambler onto the Options Connector. Replace the cover of the radio. The scrambler has been tested in firmware version.00. Note: Some versions of this radio may have a large diode (D00) installed under the options connector that can cause a short on the unit. If this diode is present protect the option board using electrical or kapton tape. VX-00/VX-00: Remove the cover of the radio exposing the options connector. Plug the scrambler onto the Options Connector. Replace the cover of the radio. The scrambler has been tested in firmware version.. VX-00/VX-00: Remove the cover of the radio exposing the options connector. Plug the scrambler onto the Options Connector. Replace the cover of the radio. The scrambler has been tested in firmware version VX-000, VX-00 & VX-000: Remove the cover of the radio exposing the options connector. Plug the FIF-A (from Vertex) onto the options connector per Vertex s instructions. Then plug the scrambler onto the FIF-A. Replace the cover of the radio. The scrambler requires firmware version.0 or higher in the VX-000. The VX- 00 has been tested with firmware version 0. The VX-000 has been tested with firmware version.0. NOTE: The scrambler should be ordered for the specific radio model. However, if you need to change radio models please see the tables at the end of this manual (before the layout drawings) for necessary component changes.

5 RADIO PROGRAMMING VX-0: For the VX-0 radio programming software CE- v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. The Option Unit should be read as FVP-. Under the Common heading select Key Function to set which key will control scramble on/off. Set the mode select button to Option Switch or Option Switch. VX-0 & VX-0: For the VX-0 & VX-0 radio programming software CE- v.00 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. Set the Option Board to Encryption (Hi Level). Under the Common heading select Key Function to set which key will control scramble on/off. Set the Side or Side Key to ACC. Press or Press & Hold may be used. The assigned button will then control scramble on/off and/or code select. On full keypad versions the A, B, C, or D button may be used. In the main screen, in the ENCR column, every channel must have the flag checked. NOTE: This does not provide encryption on a per channel basis. On this screen, the SQ column must have a figure greater than 0. VX-0 & VX-0: For the VX-0 & VX-0 radio programming software CE- v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. The Option Unit should be read as FVP-. Under the Common heading select Key Function to set which key will control scramble on/off. Set the mode select button to Option Switch. VX-00 & VX-900: For the VX-00 & VX-900 radio programming software CE-9 v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Miscellaneous. Set the Encryption Type to Hi Level. This will also change the Encryption Device setting under Common > Option to Yes. Under the Common heading select Key Function to set which key will control scramble on/off. Set the TOP SEL Key (top orange button), SIDE SEL Key (top side button), or the A, B, C, or D (keypad models only) button to ACC. The assigned button will then control scramble on/off and/or code select. In the main screen, in the ENCR column, every channel must have the flag checked. NOTE: This does not provide encryption on a per channel basis.

6 VX-00: For the VX-00 radio programming software CE- v.0 or higher (DOS) or v.0 (Windows) must be used. Read the radio with the option board installed. Select Common from the menu and then Miscellaneous. Set the Encryption Type to Hi Level. This will also change the Encryption Device setting under Common > Option to Yes. Under the Common heading select Key Function to set which key will control scramble on/off. Set the SEL Key (top orange button), SEL Key (top gray button), or the A, B, C, or D (keypad models only) button to ACC. The assigned button will then control scramble on/off and/or code select. In the main screen, in the ENCR column, every channel must have the flag checked. NOTE: This does not provide encryption on a per channel basis. VX-0 & VX-90: For the VX-0/90 radio programming software CE-9 v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. The Option Unit should be read as FVP-. Under the Common heading select Key Function to set which key will control scramble on/off. Set the mode select button to Option SW or Option SW. Option SW is momentary and Option SW is latched. VX-00 & VX-00: For the VX-00 & VX-00 radio programming software CE- v.0 or higher must be used. Read the radio with the option board installed. Key Function to set which key will control scramble on/off. Set the P-P Short Press button to Option SW. VX-00 & VX-00: For the VX-00 & VX-00 radio programming software CE-9 v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. The Option Unit should be read as FVP-. Under the Common heading select Key Function to set which key will control scramble on/off. Set the P-P or A button to Option Switch.

7 VX-00 & VX-00: For the VX-00 & VX-00 radio programming software CE- v.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. The Option Unit should be read as FVP-. Under the Common heading select Key Function to set which key will control scramble on/off. Set the P-P or A button to Option Switch. VX-000, VX-00 & VX-000: For the VX-000 radio programming software CE- v.0..0 or higher or CE-9 v..0.0 or higher must be used. For the VX-00/VX-000 radio programming software CE-9 v..0.0 or higher must be used. Read the radio with the option board installed. Select Common from the menu and then Option. Set the Option Unit to FVP- (Hi Level Encr). This will also change the Encryption Type setting under Common > Miscellaneous to Hi Level. Under the Common heading select Key Function to set which key will control scramble on/off. Set the PF- PF (long or short) button to Hi-Level Enc SW. If the short press is selected only scramble on/off is available. If the long press is selected scramble on/off and code select are available. In the main screen, in the ENCR column, every channel must have the flag checked. NOTE: This does not provide encryption on a per channel basis.

8 OPERATION Mode Select: Press the radio key that was assigned in the radio programming. A tone followed by a higher tone indicates the unit was toggled into scramble mode. A tone followed by a lower tone indicates the unit was toggled into clear mode. Code Select: When the unit is programmed with multiple security keys, pressing and holding the mode button can access different keys. A number of tones will be emitted as the unit changes from one code to another. TECHNICAL NOTES Radio Compatibility: Midian has taken the utmost care to ensure the option board integrates into the radio with minimal impact to the features of the radio. However, some features may not be available in the radio when an option board is used. RMK-000: Go-Ahead beeps are not supported in this radio. NOTE: The scrambler should be ordered for the specific radio model. However, if you need to change radio models you will need to complete the component changes on the following list. TVS--VX & VPU--VX REVISION C & D Radio C C C9 C0 C R R R R R R R9 VX K 0 K K K K 0 K 00 K VX-0/0 0 M 0 K K K K 0 K 0 K VX-0/ K 0 K K K K 00 K 0 K VX-00/00 VX-00/900/ 0 M 0 K K K K 00 K K 00/00/000/ 00 VX-00 0 M 0 K K K K 00 K 0 K VX-0/ K K K K K 0 K 0 K VX-00/ M 0 K K K K 0 K 0 K VX K 0 K K K K 0 K 0 K MIDIAN ELECTRONICS, INC. 0 East nd Street Tucson, Arizona USA Toll-Free: -00-MIDIANS Main: sales@midians.com Web: MIDIAN CONTACT INFORMATION

9 D D C C B B A A CP CJS DML 0-0- F- of MIDIAN ELECTRONICS, INC. DATE: DESIGN: DWN BY: REV: APPR COPYRIGHT REV SHEET PROJECT NUMBER DOCUMENT NAME SCHEMATIC 0 TVS--VX/VPU--VX 00K R 00K R 00K R 00K R.V OSC TCMP VDD VPP SS B D OSC B0 B 9 A A A A A A A A0 C C 0 C C0 C C C 9 C B B B RES B 0 TCAP IRQ B SCK MOSI 0 MISO 9 RDI TDO NC NC NC 9 NC 0 MC0C U SD D.V.V.u C CS SCLK SI SO NC NC CAT9C U.u C.V PAD PTT_IN PAD PTT_OUT PAD MODE_IN PAD COR_IN 0p C * RJ - + LM U: - + LM U: LM U:.00u C 9p C.M R.K R.00u C TP V+ V+ OUT OUT MAX09-S U9 0p C 00K R.V.V A A X0 X0 X X X X HC0 U: B 0 B 0 Y Y Y0 Y0 Y Y HC0 U: C 9 C 9 Z Z Z0 Z0 Z Z E\ E\ VEE VEE HC0 U:.u C9 K R.V 9p C.M R TP 0K R BSS Q 00K R 0K% R 0K% R9 00p C0 K R0 OSC OSC A A0 9 A 0 MCLR VDD VDD VSS VSS B B B B 9 B 0 B B0 B A A F U.V K R.K R.00u C.00u C K R K R.M R.00u C TP SHDN V+ CLK IN OUT COM OS V- MAX U.u C 9p C TP.V 0p C TP p C p C 9p C 0p C 0p C.K R0.0u C.V 0K R.00u C0 0p C9 * C TP TP p C p C. MHz. Y.M R PAD PROG_IN PAD PROG_OUT SJ 0K R.V.V.V UB *.u C * C.u C * UK CUT LINES ON PCB ONLY WHEN USING KEYPAD (SOURCE).00u C.0u C9.00u C 0K R K R K R K R 00K R9 P:0 NOT USED P: PTT IN P:9 +VB[NU] P: NOT USED P: NOT USED P: NOT USED P: MODE IN P: AUDIO SWITCH P: COR IN P: NOT USED P: NOT USED P: NOT USED P: RX OUT P: PTT OUT P: RX IN P: ENABLE P: TX OUT P:9 NOT USED P: TX IN P:0 NOT USED P:0 P: P:9 P: P: P: P: P: P: P: P: P: P: P: P: P: P: P:9 P: +.V[SW] P:0 GUIDE HOLE P: GUIDE HOLE P: VS VS OUT OUT TRG TRG THS THS MIC U - + LMV U: - + LMV U: LMV U: - + LMV U: LMV U:

10 - This page intentionally left blank -

11

12