Adaptabel AC Single Stroke Bells
|
|
- Georgiana Osborne
- 6 years ago
- Views:
Transcription
1 Adaptabel AC Single Stroke Bells PLC Compatible 332 Series > Completely assembled, all hardware supplied > Universal Adaptaplate mounts directly on surface or electrical box > Shockproof die cast housing > Dustproof AGENCY APPROVALS > UL 464 Listed > FM Listed SPECIFICATIONS > Rated 400 hours at 50% duty cycle > Self-compensating solenoid plunger Adaptabel single stroke bells produce an individual, clearly defined note. When current is applied, the striker hits the gong once and stops. Coded, intermittent current may be used to cause the striker to hit the gong, pause and hit again for any given period. Ideal for use with momentary initiating contacts. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. See accessories on page Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. See Accessories on page 5-10 for available options. > Corrosion resistant heat flowed epoxy finish 5-2
2 TECHNICAL INFORMATION 4 1/2" (114 mm) 4" Bell 2 13/32" (61 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 3 11/16" (94 mm) 10 1/2" (267 mm) 7 1/8" (181 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 332-4G5 24V AC 50/60 Hz / N5 120V AC 50/60 Hz G5 24V AC 50/60 Hz / N5** 120V AC 50/60 Hz R5 240V AC 50/60 Hz G5 24V AC 50/60 Hz / N5** 120V AC 50/60 Hz *Gong Size in inches denoted by suffix in catalog number. ** Diode Polarized models avaiable. Order 332D-6N5 or 332D-10N5. Add "-R" for red. SIGNAL INPUT LOAD CHARACTERISTICS Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 332-4N5 120V AC 60 Hz / N5 120V AC 60 Hz / N5 120V AC 60 Hz /4.5 This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-3
3 Adaptabel AC Single Stroke Bells Explosionproof, NEMA Type 4 332EX Series > 6" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location AC single stroke bells produce a distinctive, loud, and clear individual note that is free of mechanical clatter. When current is applied, the striker hits the gong once and stops. Current may be coded to cause the striker to hit the gong intermittently. Ideal for use with momentary initiating contacts. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Used for coded signal applications such as paging. Also specified for timing, scheduling, and general alarm applications in: Refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-12
4 TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) Peak db at Cat No. Volts Current* 1m / 10 ft. Gong Size 332EX-6G5 24V AC 50/60 Hz 3.40A 92 / 86 6" (152 mm) 332EX-6N5 120V AC 50/60 Hz 0.43A 332EX-6R5 240V AC 50/60 Hz 0.20A 332EX-10G5 24V AC 50/60 Hz 3.40A 100 / 94 10" (254 mm) 332EX-10N5 120V AC 50/60 Hz 0.43A 332EX-10R5 240V AC 50/60 Hz 0.20A *Single pulse duration - 8 to 16 milliseconds 5-13
5 Adaptabel DC Single Stroke Bells PLC Compatible 333 Series > Universal Adaptaplate mounts directly on surface or electrical box > Indoor AGENCY APPROVALS > UL 464 Listed DC single stroke bells produce an individual, clearly defined note. When current is applied, the striker hits the gong once and stops. Coded, intermittent current may be used to cause the striker to hit the gong, pause and hit again for any given period. Ideal for use with momentary initating contacts. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. See AdaptaBel Accessories on page
6 TECHNICAL INFORMATION 4" (102 mm) 4" Bell 2 15/32" (63 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 2 29/32" (74 mm) 10" (254 mm) 6" (152 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 333-4G / E G / P G / P *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 333-4G1 24V DC / G1 24V DC / G1 24V DC / **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-5
7 Adaptabel AC Vibrating Bells PLC Compatible 340 Series > Universal Adaptaplate mounts directly on surface or electrical box > Weatherproof by adding appropriate back box > Completely assembled, all hardware supplied > Shockproof die cast housing > Dustproof AGENCY APPROVALS > UL 464 Listed > FM Listed > CSFM Certified SPECIFICATIONS AC vibrating bells produce a long continuous ringing sound. The striker continues to strike the gong in rapid-fire action as long as current is applied. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. May be weatherproofed with the addition of a weatherproof box. See AdaptaBel Accessories on page 5-10 for available options. > Self-compensating solenoid plunger > Rated 400 hours at 50% duty cycle > Corrosion resistant heat flowed epoxy finish 5-6
8 TECHNICAL INFORMATION 4" Bell 4 1/2" (114 mm) 2 13/32" (61 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 7 1/8" (181 mm) 3 11/16" (94 mm) 10 1/2" (267 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 340-4E / FM G N R E / FM G N R G / N R *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 340-4N5 120V AC 60 Hz / N5 120V AC 60 Hz / N5 120V AC 60 Hz /4 **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-7
9 Adaptabel DC Single Stroke Bells Explosionproof, NEMA Type 4 333EX Series > 6" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location DC single stroke bells produce a distinctive, loud, and clear individual note that is free of mechanical clatter. When current is applied, the striker hits the gong once and stops. Current may be coded to cause the striker to hit the gong intermittently. Ideal for use with momentary initiating contacts. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Used for coded signal applications such as paging. Also specified for timing, scheduling, and general alarm applications in refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-14
10 TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) Peak db at Cat No. Volts Current* 1m / 10 ft. Gong Size 333EX-6G1 24V DC 3.50A 92 / 86 6" (152 mm) 333EX-6P1 125V DC 0.52A 333EX-10G1 24V DC 3.50A 100 / 94 10" (254 mm) *Single pulse duration - 8 to 16 milliseconds 5-15
11 AdaptaBuzzer TM AC and DC Models > Vibrating Armature > Universal Adaptaplate mounts directly on surface or electrical box > Plug-in convenience > Corrosion resistant heat flowed epoxy finish AGENCY APPROVALS > 340A Series UL 464 Listed > 340A Series FM Approved 340A & 343A Series Edwards vibrating AdaptaBuzzers are the finest, heavy duty buzzers available. The AC models are volume adjustable. Universal Adaptaplate mounts directly on any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box. Buzzer plugs into receptacle on mounting plate. For flush mounting accessories see page Used for timing, scheduling, and paging applications. Use wherever a relatively low decibel signal of a different tone is required. 2 1/4" (57mm) 5 1/16" (128mm) 5-28 DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. 340A-G5 24V 50/60 Hz 0.250A / A-N5 120V 50/60 Hz 0.050A A-R5 240V 50/60 Hz 0.025A A-E1 12V DC / A-G1 24V DC A-M1 75V DC A-P1 125V DC
12 Adaptabel AC Vibrating Bells Explosionproof, NEMA Type 4 340EX Series > 6", 8" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location AC vibrating bells produce a distinctive, loud, and clear ringing sound that is free of mechanical clatter. The striker continues to strike the gong in rapid-fire action as long as current is applied. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Specified for timing, scheduling, paging, and general alarm applications in refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-16
13 TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C C 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 8" 5 1/16" 5 1/4" 1 5/8" (203mm) (129mm) (133mm) (41mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) RMS db at Cat No. Volts Current 1m / 10 ft. Gong Size 340EX-6G5 24V AC 50/60 Hz 0.210A 90/84 6" (152mm) 340EX-6N5 120V AC 50/60 Hz 0.041A 340EX-6R5 240V AC 50/60 Hz 0.021A 340EX-8N5 120V AC 50/60 Hz 0.041A 95/89 8" (203mm) 340EX-10G5 24V AC 50/60 Hz 0.210A 94/88 10" (254mm) 340EX-10N5 120V AC 50/60 Hz 0.041A 340EX-10R5 240V AC 50/60 Hz 0.021A 5-17
14 General Purpose Bells Solid Brass Shell 432 Series Compact single-stroke bell sounding a crisp, clean tone. For low cost, light duty installations in factories, institutions, offices, and OEMs. Uses include: doorbells, extension signals, warning bells, and audible annunciation. Ideal for end of cycle timing, signaling, and paging. > Low cost > 2 1/2" Solid Brass Shell > Low current drain permits long wire runs 1 1/4" (32mm) 2 1/2" (64mm) 1 1/2" (38mm) DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft 432-G5 24V AC / N5 120V AC /
15 Adaptabel DC Vibrating Bells PLC Compatible 435 Series > Universal Adaptaplate mounts directly on surface or electrical box > Weatherproof by adding 449 back box > 4", 6" 8" and 10" gong sizes AGENCY APPROVALS > UL 464 Listed DC vibrating bells produce a long continuous ringing sound. The striker continues to strike the gong in rapid-fire action as long as current is applied. Universal Adaptaplate mounts directly on surface or fits any single gang box, 3 1/4" (83mm), 3 1/2" (89mm), or 4" (102mm) octogon box, or any plaster cover with mounting holes on 2 3/4" (70mm) centers. 6" and 10" bells also mount on 4" (102mm) square boxes. The DC vibrating bell can be used in outdoor applications when mounted on Cat. No. 449 weatherproof back box. See AdaptaBel accessories on page Specified for timing, scheduling, and general alarm applications. 5-8
16 TECHNICAL INFORMATION 6" Bell 4" Bell 2 29/32" 2 15/32" (74 mm) (63mm) 4" (102mm) 6" (152 mm) 10" Bell 4 13/16" (122 mm) 8" Bell 3 11/32" (85mm) 10" (254 mm) 8" (203mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 435-4C / E / G / J / P / C / E / G / J / K / P / S / C / E / G / P / E / G / P / S / *Gong Size denoted by suffix in catalog number. *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 435-4G1 24V DC / G1 24V DC / G1 24V DC / **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs. 5-9
17 Adaptabel DC Vibrating Bells Explosionproof, NEMA Type 4 435EX Series > 6", 8" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof > Diode Polarized Models available for use in electrically supervised circuits AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III Hazardous location DC vibrating bells produce a distinctive, loud, and clear ringing sound that is free of mechanical clatter. The striker continues to strike the gong in rapid-fire action as long as current is applied. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Specified for timing, scheduling, paging, and general alarm applications in: Refineries, gasoline storage and dispensing areas, Petrochemical manufacturers, Spray paint areas, Aircraft hangers, Grain dust areas in granaries and flour mills, and Industrial firms using flammable liquids. > NEMA Type 4 SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-18
18 TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 7/16" (37mm) 1 1/4" (32mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 8" 5 1/16" 5 1/4" 1 5/8" (203mm) (129mm) (133mm) (41mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) 6" ± 1/8" (152mm ± 3mm) Mounting Brackets RMS db at Cat No. Volts Current 1m / 10 ft. Gong Size 435EX-6C EX-6E EX-6G /83 6" (152mm) 435EX-6K EX-6P EX-6S EX-8G EX-8K /86 8" (203mm) 435EX-8P EX-8S EX-10E EX-10G /89 10" (254mm) 435EX-10P DEX-6G /83 6" (152mm) 435DEX-8G /86 8" (203mm) 435DEX-10G /89 10" (254mm) + Diode polarized for use in electrically supervised circuits. CSFM Listed 5-19
19 General Purpose Miniature Bells AC and DC Models 13 Series > 1", 2" and 3" sizes > Long Life > Dust proof covers > Adjustable volume Compact size and pleasant sound make these bells desirable for use in offices, apartment houses, intercom and telephone signaling, machinery and other OEM uses. Suitable for AC powered security systems with battery standby. > Grounded frame > External binding posts > Chrome plate finish D B C A DC Coil db at Dimension Cat No. Size Volts Amps VA Res (ohms) 1 m / 10 ft. A B C D 13-1AB 1" 5-10 DC (25 mm) 6-12 AC / /4" 3/4" 3 1/8" 1 3/4" 13-1G1 24 DC (32mm) (19mm) (79mm) (44mm) 13-1G5 24 AC AB 2" 5-10 DC (51 mm) 6-12 AC / /4" 1 1/16" 3 29/32" 2 1/32" 13-2G1 24 DC (44mm) (27mm) (99mm) (52mm) 13-2G5 24 AC AB 3" 5-10 DC (76 mm) 6-12 AC / 67 3" 1 9/16" 5 7/8" 3 1/2" 13-3G1 24 DC (76mm) (40mm) (149mm) (89mm) 13-3G5 24 AC
20 General Purpose Bells AC and DC Models 55 Series Economy single magnet bell. Exposed striker, vibrating bell comes with an enclosed grounded terminal and case. For low cost, light duty installations in factories, institutions, offices, and OEMs. Used as doorbells, extension signals, warning bells, and audible annunciators. Especially suitable for AC powered security systems with battery backup. > 4" and 6" gong sizes > AC and DC Models > Low Voltage > Gray finish > Low current drain permits long wire runs B C A DC Coil db at Dimension Cat No. Size Volts Amps VA Res (ohms) 1m / 10 ft. A B C 55-4AM 4" 6V DC 0.85A " 2 1/8" 7 3/8" (102mm) 8V AC 1.10A / 68 (102mm) (54mm) (187mm) 55-4G5 24V AC 0.20A AM 6" 6V DC 0.80A " 2 5/8" 10 5/8" (152mm) 8V AC 1.00A / 74 (44mm) (27mm) (99mm) 55-6G5 24V AC 0.20A
21 General Purpose Bells AC and DC Models > 3", 4" and 6" gong sizes > Low current drain permits long wire runs > Supplied with weatherproof gasket for outdoor applications > Corrosion resistant gray finish 156G Series Self-contained underdome monitor bell. Weatherproof, insulated, and grounded vibrating bell with concealed plunger. Mounts on 3 3/4" (95mm) bolt circle. For low cost, light duty installations in factories, institutions, offices, and OEMs. Uses include doorbells, extension signals, warning bells and annunciation. Suitable for AC systems with battery backup. B A db at Dimension Cat No. Size Volts Amps 1m / 10 ft. A B 156G-3AM 3" 6-8V DC 8-10V AC G-3AX (76 mm) 12-18V DC " 1 7/8" 156G-3G1 24V DC / 72 (76mm) (48mm) 156G-3G5 24V AC G-4AM 4" 6-8V DC 8-10V AC " 1 7/8" 156G-4G1 (102 mm) 24V DC / 76 (102mm) (48mm) 156G-4G5 24V AC G-6AM 6-8V DC 8-10V AC G-6AW 6" 20-24V DC / 80 6" 2 5/16" 156G-6G1 (152 mm) 24V DC 0.15 (152mm) (59mm) 156G-6G5 24V AC
22 General Purpose Dixie Bell TM Fully Enclosed > Low voltage > AC and DC operation > Attractive snap-on covers > Enclosed binding posts > Corrosion resistant metallic finish 720 Series Low cost, non adjustable bell which may be operated off of a 590 transformer or DC power. Universal economy bell widely used in homes, apartment houses, plants, OEMs. Especially suitable for AC powered security systems with battery standby. For office installation, see Cat. No. 13 Series Bells on page 5-22 or Cat. No. 15 and 115 Series Buzzers on pages 5-34 and For combination bell and buzzer see Cat. No. 730 Dixie Buzabel TM on page " (76mm) 1" (25mm) 5 1/4" (133mm) DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft V AC 1.20A / V DC 5-26
23 Nubel General Purpose Bells AC and DC Models 740 & 744 Series Low cost, non adjustable bell which may be operated off of a 590 transformer or DC power. Universal economy bell widely used in homes, apartment houses, plants, OEMs. Especially suitable for AC powered systems with battery standby. For office installation, see Cat. No. 13 Series Bells on page 5-22 or Cat. No. 15 and 115 Series Buzzers on pages 5-34 and For combination bell and buzzer see Cat. No. 730 Dixie Buzabel TM on page > AC and DC Models > Low Voltage > Exposed gong > Attractive snap-on covers > Enclosed binding posts > Corrosion resistant metallic finish B C A DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C V AC / /2" 1 1/4" 5 3/4" 3-6V DC (64 mm) (32 mm) (146 mm) V AC / 78 4" 1 3/4" 6 7/8" 3-6V DC (102mm) (44mm) (175mm) 5-27
24 Dixie Buzzer TM & Dixie Buzabel TM Low voltage > Low voltage > Attractive snap on covers > Fully enclosed > Satin aluminum finish > Cat. No enclosed binding posts > Cat. No enclosed terminals 725 & 730 Series The Cat. No. 725 is a low cost, fully insulated, non adjustable buzzer. The Cat. No. 730 is a low cost, non adjustable combination bell and buzzer with grounded frame. May be operated using AC power supplied by a 590 transformer or from DC power. See Transformer Catalog Page Universal economy buzzer or bell and buzzer combination widely used in homes, apartment houses, plants, and OEMs. A 1" (25mm) B 5-36 DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft A B 725 6V AC 1.20A / /4" 2 3/4" (45mm) (69mm) 730 6V AC 0.7A / 82 3" 5 1/4" 3-6V DC 1.4A 8 3 (76mm) (133mm) 6-8V AC 60 Hz 1.4A 8 3
25 Miniature Lungen TM Buzzer AC and DC Models 15 Series > Adjustable volume > Chrome cover; zinc plated base Compact, dependable buzzer designed for long life and trouble-free installations. For installation in commercial buildings, offices, and OEM applications. B C D A 5-34 DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D 15-0AJ 5-8V DC V AC / /8" 1 15/32" 1/2" 1 13/32" 15-0G1 24V DC (41mm) (37mm) (13mm) (36mm) 15-0G5 24V AC AB 5-10V DC V AC /8" 1 13/16" 19/32" 1 53/64" 15-1E1 12V DC / 68 (54mm) (46mm) (15mm) (46mm) 15-1G1 24V DC G5 24V AC AB 5-10V DC V AC / /8" 2 3/8" 15/16" 2 3/32" 15-2G1 24V DC (66mm) (60mm) (24mm) (53mm) 15-2G5 24V AC AB 5-10V DC V AC " 2 1/2" 7/8" 2 3/8" 15-3E1 12V DC / 74.5 (76mm) (64mm) (22mm) (60mm) 15-3G1 24V DC G5 24V AC
26 Miniature Lungen TM Buzzer AC Operation 115 Series Compact, dependable buzzer designed for long life and trouble-free installations. For installation in commercial buildings, offices, and OEM applications. > Adjustable volume > Chrome cover > Zinc plated base > Contact-less B C D A DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D 115-1AC 8V AC / /32" 1 9/32" 5/8" 1 25/32" 115-1G5 24V AC (55mm) (32mm) (16m) (45mm) 115-2AC 8V AC / /8" 1 11/16" 25/32" 2 3/32" 115-2G5 24V AC (66mm) (43mm) (20mm) (53mm) 115-4AC 8V AC / /16" 2 3/16" 1 1/8" 2 27/32" 115-4G5 24V AC (87mm) (55mm) (28mm) (72mm) 5-35
27 Midi Vibrating Horns Compact size 118 & 123A Series Edwards 118 Series DC and 123A Series AC Midi Vibrating Horns are designed primarily for security systems and for signaling devices on an OEM basis. Supplied with mounting bracket and simply attaches to mounting surface using #8-32 screw. Used for security systems, office machines, low-voltage trouble alarms, home appliances, data monitoring systems, computers, and timing devices. > Low power drain > Compact size > Shock resistant > Easy surface mount installation SPECIFICATIONS > Temperature range: -40 to 180 F (-40 to 82 C) > Weight: 3 oz (85g) 3/16" (5mm) 2 1/32" (51mm) 1 3/4" (45mm) A 6" (152mm) 2 wires on AC DC Coil db at Width Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. (A dimension) 118-E1 12V DC 0.07A / /64" 118-G1 24V DC 0.03A (30mm) 123A-E5 12V AC 60 Hz 0.4A / /16" 123A-G5 24V AC 60 Hz 0.2A (30mm) 123A-N5 120V AC 60 Hz 0.04A
28 Strap Mounted Buzzer Low power drain > High voltage Cat. No > Adjustable volume > Zinc-plated finish > Low power drain permits long wire runs > 1064 has terminal connectors > 1065 has flying leads 1064 & 1065 Series Flush mounted, heavy duty buzzer designed for standard outlet box installation. The 1064 Series are provided with terminals for wiring connections. The 1065 Series are provided with flying leads for wiring connections Installs in standard outlet boxes using any standard wall plate. Low cost, quality buzzer widely used in homes, apartment houses, plants, and OEMs. AGENCY APPROVALS > UL 464 Listed 1" (25mm) 3 3/4" (95mm) 2 3/8" (60mm) 3 3/16" (81mm) 1 3/8" (35mm) Cat. No Shown DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft G5 24V AC 50/60 Hz 0.25A / N5 120V AC 50/60 Hz 0.05A R5 240V AC 50/60 Hz 0.025A G5 24V AC 50/60 Hz 0.25A / N5 120V AC 50/60 Hz 0.05A R5 240V AC 50/60 Hz 0.025A
29 High Voltage Buzzer Low power drain 1066 Series Designed for standard outlet box installation. Provided with leads for wiring connections. Low cost, quality buzzer widely used in homes, apartment houses, plants, and OEMs. > High voltage > Adjustable volume > Zinc-plated finish > Low power drain permits long wire runs AGENCY APPROVALS > UL Recognized 1 1/4" (32mm) 13/16" (21mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft G5 24V AC 50/60 Hz 0.25A / N5 120V AC 50/60 Hz 0.05A R5 240V AC 50/60 Hz 0.025A
30 Flush-Call Strap Mounted Signals Low voltage 660 Series The Edwards 660 Series are compact, strap-mounted buzzers and bells designed for flush mounting in standard electrical boxes. > Low voltage > Easy flush mounting Designed for installation in standard outlet boxes. Requires a 590 transformer (page 11-2) and push button. Transformer and pushbutton may be mounted in same 3 gang outlet box with a minimum depth of 1 3/4" (44 mm) using a Cat. No. 593 transformer mounting plate (page 11-4). Used for residential and commercial door signals and interoffice communications and signaling. 660/ Typical Wiring Diagram 1 3/4" (44mm) A 590 Transformer 8/10V AC 115V AC 3 5/8" (92mm) DC Coil db at Cat No. Name Voltage Current* VA Res. (ohms) 1m / 10 ft. Depth (A) 660 Ringcall TM Bell 8-10V AC 1.5A / /8" (35 mm) 661 Buzacall TM Buzzer 8-10V AC 1.3A / 80 7/8" (22 mm) 662 Tucall TM Bell/Buzzer 8-10V AC 1.5A / /8" (35 mm) *Current ratings at 10V AC. 5-39
31 AdaptaBuzzer TM Weatherproof DC & AC Models B-8698 & B-8699 Series Edwards B-8698 & B-8699 AdaptaBuzzers are the finest, heavy duty buzzers available. Sound is produced by the hammer action of a vibrating armature against the cover and starts and stops instantly with current impulse. The cover is secured to the unit's cast box by a cast aluminum threaded ring and sealed with a neoprene gasket. Two mounting lugs are provided for wall mounting. A 1/2" (13mm) tapped conduit entrance is provided on one side for field wiring. Wiring connections are made in the base and the cover assembly plugs into a receptacle in the base. Ideal for use in areas where a louder signal would be distracting. Often used for timing, scheduling, paging, and general alarm applications. Typical indoor and weatherproof installations include construction sites, shipping docks, and paper mills. > Heavy gauge steel cover > Die cast aluminum housing > Vibrating armature > Gray finish AGENCY APPROVALS > B-8699 Series UL 464 Listed > NEMA Type 3R Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-8698-E1 12V DC /89 B-8698-G1 24V DC db min. B-8698-P1 125V DC B-8698-S1 240V DC B-8699-G5 24V AC 60 Hz /89 B-8699-N5 120V AC 60 Hz db min. 5-29
32 AdaptaBuzzer TM Explosionproof > Cast aluminum housing and cover > Corrosion resistant heat flowed powder epoxy finish AGENCY APPROVALS > UL 1203 Listed B-KM-8140 & B-8141 The Edwards B-KM-8140 & B-8141 series AdaptaBuzzers are quality, heavy duty AC & DC buzzers designed for use in hazardous locations. The sound is produced by the hammer action of a vibrating armature against the cover. The buzzers are provided with two mounting lugs for wall mounting. A 1/2" (13mm) tapped conduit entrance is provided on one side for field wiring. Wiring connections are made in the base of the unit and the cover assembly plugs into a receptacle in the base. For use in hazardous location areas where a distinctive, lower db buzzer signal is required for timing, scheduling, paging, and general alarm applications. Typical installations include petroleum plants, gas plants, grain elevators, flour and paper mills, textile plants, and tankers. Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) 5-30 DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-KM-8140-G5 24V AC 60 Hz / 89 B-KM-8140-N5 120V AC 60 Hz db min. B-KM-8140-R5 240V AC 60 Hz B-8141-G1 24V DC / 89
33 Mineguard TM Mine Buzzers MSHA Certified B-8140-M & B-8141-M The Edwards B-8140-M & B-8141-M Mineguard series are quality, heavy duty buzzers suitable for use on permissible mining equipment. They are available in AC and DC voltages. The sound is produced by the hammer action of a vibrating armature against the cast aluminum cover. A one piece cast aluminum cover provides an effective explosion-proof seal; the seal is secured by a hex screw in the cover. For power connections, the unit features an installed 33" (84mm) power cord and conduit hose constructed of flame retardant neoprene. The buzzer is provided with two mounting lugs for wall mounting. For use in all mining applications. Designed to withstand the constant vibration associated with mining equipment such as loaders, carriers, and conveyors. > Heavy duty cast aluminum housing and cover > Corrosion resistant heat flowed powder epoxy finish AGENCY APPROVALS > MSHA Certified No. X/P > Conforms with MSHA 30 CFR, Part 18 for methane and air mixtures Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-8140-M-G5 24V AC 60 Hz B-8140-M-N5 120V AC 60 Hz / 89 B-8140-M-R5 240V AC 60 Hz B-8141-M-G1 24V DC / 89 B-8141-M-S1 250V DC
34 Lumatone Electronic Signals Audio or Audio/Visual E100 Series > Low cost and size > Solid state, long life > High impact polystyrene case > Pulsating audio or audio/visual models available > Terminal connections SPECIFICATIONS > Operating temperature range: -32 to 131 F (-0 to 55 C) > Frequency: 2.8 khz Edwards Lumatone signals are designed to demand attention in quiet and moderate noise areas. The signal s output can be varied by controlling the applied voltage. The signal s low power consumption makes them suitable for battery operated equipment and allows them to be turned on and off by integrated circuits, SCRs and transistors. Simply unscrew front housing and insert threaded portion through a 1 5/32" (29mm) panel hole. Screw front housing back on. Signal can accommodate panel thickness up to 3/16" (5mm). Used for security systems, computers, appliances and industrial, process control, communication and restaurant equipment. DECIBELS VS. VOLTAGE FOR LUMATONE AUDIO SIGNALS Typical at Normal Temperature "* (44mm) 1.31" (33mm) db at 1 foot " (37mm) 1.64" (42mm) Volts DC *Does not include panel thickness Max. Operating Pulsating LED Cat No. Description Voltage Current VA Rate Intensity E102A Steady audio 12V DC 10 ma 0.12 N/A N/A 24V DC 18 ma 0.44 N/A E103A Pulsating audio 12V DC 10 ma N/A 24V DC 18 ma E104A Steady visual/audio 12V DC 16 ma 0.20 N/A 1.3 mcd 24V DC 30 ma 0.75 N/A E105AE Pulsating visual/audio 12V DC 16 ma mcd 24V DC 30 ma
Modular Lube Lubrication Systems System Controls
Model 84501 Program Timer Solid State Designed to control the lubrication cycle frequency of air-operated single-stroke pumps. Timer turns pump on/off at programmed intervals via a 3-way or 4-way air solenoid
More informationXML LED X M L L E D. Explosionproof Linear LED Lighting
LED Class I, Division 1, Groups C & D Class I, Division 2, Groups C & D Class II, Division 1, Groups E, F & G Class III Simultaneous Presence UL 844 Hazardous Locations IEC Ex d Zone 1 Equivalent UL 924
More informationDry Type Transformers. Section 10. BuyLog Catalog 10-1
For more information on these products, order publications listed in Section 27. Find What You Need Faster - Page headings and table format make product selection easier. Easy Cross Reference - Frame size
More information5530M and 5530MHV Adaptatone Installation Sheet
5530M and 5530MHV Adaptatone Installation Sheet NOTE: Any kind of service or maintenance performed while unit is energized will void the warranty. 1. Mount Adaptatone as shown in Figure 2. a. Flat Surface
More informationDistributed Design Series
D10SUB 10-INCH FEATURES Powerful, high-impact bass response Internal passive low-pass crossover Spring loaded Drop-Stop installation assistant tabs support the back can on the included rails and C-ring
More informationEXPlora. Introduction
Introduction EXPlora The EXPlora range is most suited to manufacturers of ancillary electrical equipment such as motors, pumps, lighting equipment, process and control gear for use in factories and plant
More information3.5. Control Relays and Timers. Contents. 9575H Series 3000 Type AA, AC and DC. General Purpose Relays Type AA
.5 9575H Series 000 Relay Contents 9575H Series 000 Type AA, AC and DC Product Selection....................... Accessories............................ Technical Data and Specifications........... Dimensions............................
More informationGENESIS Indoor Air Conditioners
Product Overview : Indoor Air Conditioners M28 Model M52 460 Volt 3-Phase Model M17 Model 68 68 Product Overview : The specifier s choice for cooling industrial process controls Indoor Air Conditioners
More informationDry Type Transformers Section 10
For more information on these products, order publications listed in Section 27. Find What You Need Faster - Page headings and table format make product selection easier. Easy Cross Reference - Frame size
More informationSQM40/41 Actuators for air and gas dampers
SQM40/41 Actuators for air and gas dampers Description SQM40/41 actuators are used for the positioning of flow control valves, butterfly valves, dampers or any application requiring rotary motion. The
More informationENCAPSULATED TRANSFORMERS FOR HARSH LOCATIONS
SECTION ENCAPSULATED TRANSFORMERS FOR HARSH LOCATIONS 600 Volt Class, Encapsulated Single Phase and Three Phase Description and Applications... 8 Copper NEMA R Features... 8 Copper Single Phase Selection
More informationContactors. Agency approvals. UL 508 Guide No. NLDX2, File # E CE/Semko Certified EN :1991 IEC DP 30 C 3P - 1 /B
Contactors Applications Type DP provide high performance with flexibility and reliability, designed to match numerous applications including: Motors Power supplies Food service equipment Compressors Business
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM 6031 SINGLE MODE FIBER OPTIC VIDEO TRANSMISSION EQUIPMENT
1995 Metric CSJ 0508-01-258 SPECIAL SPECIFICATION ITEM 6031 SINGLE MODE FIBER OPTIC VIDEO TRANSMISSION EQUIPMENT 1.0 Description This Item shall govern for the furnishing and installation of color Single
More informationThree Phase - General Purpose. THREE PHASE: 3 kva - 9 kva Epoxy Encapsulated Series 76 ISO-Shield
26 THREE PHASE: 3-9 Epoxy Encapsulated Series 76 ISO-Shield Features UL Listed, File E3210. CSA Certified, File LR 560. Electrostatic shield between primary and secondary windings provides cleaner output
More informationMagnecraft General Purpose Relays 750R Series DPDT and 3DPT, 10 A
and 3DPT, 10 A UL Listed when used with proper Magnecraft s The 750R series octal base, plug-in relays offer clear or full-feature covers with multiple mounting options and accessories. 750R 750R Full-Feature
More informationAgency approvals UL 508 Guide No. NLDX2, File # E CE/Semko Certified EN :1991 IEC DP 30 C 3P - 1 /B
11 Applications Type DP provide high performance with flexibility and reliability, designed to match numerous applications including: Motors Power supplies Food service equipment Compressors Business machines
More informationHN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
More informationAbsolute Encoders Multiturn
The Sendix 5863 and 5883 multiturn encoders with SSI or BiSS-C interface and optical sensor technology can achieve a resolution of max. 29 bits. A through hollow shaft up to 4 mm and a blind hollow shaft
More informationAC1036. Definite Purpose Contactors
Definite Purpose Contactors Definite purpose contactors Definite purpose Contactors Applications Type DP contactors provide high performance with flexibility and reliability, designed to match numerous
More informationCast Aluminum Circuit Breaker Interlocked Receptacle (Cutaway View)
30A 400A (30 200A Load Breaking), Maximum 600VAC/250VDC Receptacles, Inlets, Plugs, Connectors, Interlocked Receptacles, Explosion-Proof Interlocked Receptacles Cast Aluminum Circuit Breaker Interlocked
More informationMILLITARY SPECIFICATION SHEET
INCH-POUND MILLITARY SPECIFICATION SHEET 10 November 2000 SUPERSEDING MIL-R-6106/14B 10 March 1989 RELAY, ELECTRIC, PERMANENT DRIVE, 50 AMP, SPDT (DB) DOUBLE MAKE DOUBLE BREAK AUXILIARY CONTACTS (5 AMP),
More informationWeekly Time Switch. Rated time Time setting range Time division 24 hrs x 7 days 00:00 to 23:59 1min
Weekly Time Switch Easy Programming with Large LCD Display and Interactive Functions Programming for 24 hrs x 7 days using just five switches. Sixteen program steps available. Power supply freely selectable
More informationGENESIS Indoor Air Conditioners
PH FX ( Product Overview : Indoor Air Conditioners M28 Model M52 460 Volt 3-Phase Model M17 Model 74 74 Product Overview : The specifier s choice for cooling industrial process controls Indoor Air Conditioners
More informationSPECIAL SPECIFICATION 6911 Fiber Optic Video Data Transmission Equipment
2004 Specifications CSJ 3256-02-079 & 3256-03-082 SPECIAL SPECIFICATION 6911 Fiber Optic Video Data Transmission Equipment 1. Description. Furnish and install Fiber Optic Video Data Transmission Equipment
More informationSPECIAL SPECIFICATION 1987 Single Mode Fiber Optic Video Transmission Equipment
1993 Specifications CSJ 0027-12-086, etc. SPECIAL SPECIFICATION 1987 Single Mode Fiber Optic Video Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation of color
More informationSeries CDP2 Definite Purpose Contactors
Series 2 Definite Purpose High performance economical contactors for commercial applications up to 90 Sprecher + Schuh s Definite Purpose contactors are ideal for commercial applications including air
More informationWLB SERIES HID Lighting for Hose Down Applications
WLB SERIES W LB HID Lighting for Hose Down Applications Class II, Division 2, Groups F & G Class III UL 844 Hazardous Locations UL 1598 Wet Locations NEMA 4X NSF Certified Food Equipment CUL Heavy Hose
More informationFlexible Cord. Inside this section
2 Strain Relief Cord Connectors provide a liquid tight and strain relief termination for flexible type neoprene, vinyl, or PVC control cord and cable, and are now offered in steel, aluminum, and nylon.
More informationPendant Light Fitting IEC Series 6470/2
> Available light sources high-pressure sodium lamps (HSE) metal halide lamps (HIE) halogen lamps (QT) > Versatile mounting methods > Enclosure made of saltwater-resistant aluminium www.stahl.de 11435E
More informationSPECIAL SPECIFICATION 1291 Fiber Optic Video Data Transmission Equipment
1993 Specifications CSJ 0500-01-117 SPECIAL SPECIFICATION 1291 Fiber Optic Video Data Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic Video
More informationLinear flow controls VFC Linear flow controls with actuator IFC
Linear flow controls VFC Linear flow controls with actuator Product brochure GB 3 Edition 01.16 Linear relationship between adjustment angle and flow rate Large control ratio of 25:1 Actuators IC 20 or
More informationDMP 335 DMP 335. Industrial Pressure Transmitter. Welded, Dry Stainless Steel Sensor. Pressure Transmitter. Industrial
DMP 5 Industrial Pressure Transmitter Welded, Dry Stainless Steel Sensor accuracy according to IEC 60770: 0.5 % FSO Industrial Pressure Transmitter Nominal pressure from 0... 6 bar up to 0... 600 bar Output
More informationType Contact form Model PCB SPDT G6E-134P-ST-US G6E-134PL-ST-US. Type Contact form Model
Low Signal Relay G6E Subminiature 7.87 H x.1 W x 16 L mm (0.31 H x 0.3 W x 0.63 L in). High sensitivity with pick-up coil power of 8 mw. Surge withstand meets FCC Part 68 rule and Telcordia 2.5 kv Specifications.
More informationGOYEN PILOT VALVE ENCLOSURES FOR HAZARDOUS LOCATIONS CLEAN AIR SOLUTIONS PRODUCT LEAFLET
PILOT VALVE ENCLOSURES FOR HAZARDOUS LOCATIONS CLEAN AIR SOLUTIONS 3-6VFD COMBINATION FLAME AND DUST IGNITION PROOF ENCLOSURES Goyen pilot valve enclosures for hazardous locations are available in a combination
More information20 mm Beam Pitch General Purpose Area Sensor. Distance between parts shelf and sensor can be shortened (Enables miniaturization of equipment)
OTHER SUNX PRODUCTS SERIES 0 mm Beam Pitch General Purpose Area Sensor Diagnosis Self-diagnosis Test input Interference prevention Wide sensing area of 7 m,60 mm with 0 mm beam pitch Refer to p.9l for
More informationMASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz
Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO
More informationIndyGo Facility Upgrades Project 35671EE
SECTION 260553 IDENTIFICATION FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Identification for raceways. 2. Identification of power and control cables. 3. Identification for
More informationSeries CDP2 Definite Purpose Contactors
Series CDP2 Definite Purpose Contactors High performance economical contactors for commercial applications up to 90 Sprecher + Schuh s Definite Purpose contactors are ideal for commercial applications
More informationNo-Hub Couplings Drainage Drains Cleanout Plugs Cover Plates
Flexible Couplings Transitions all types of DWV plastic, copper, steel, cast iron and clay pipe. 300 series stainless steel clamps Flexibility - Sleeve is manufactured of molded natural and synthetic rubber
More informationQuick-disconnect cables. Adjustable mounting brackets
MiniSafe File No. LR90200 Operation MiniSafe 1.0 inch (25.4 mm) resolution 100 foot (30.5 m) range Individual Beam Indicator lights covered by U.S. and international patents Compact size 2.25 x 1.8 inches
More informationSPECIAL SPECIFICATION 6735 Video Optical Transceiver
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6735 Video Optical Transceiver 1. Description. This Item governs the furnishing and installation of Video optical transceiver (VOTR) in field location(s)
More informationGOODMAN BENTLEY STEREOPHONIC STETHOSCOPE OPERATING INSTRUCTIONS
GOODMAN BENTLEY STEREOPHONIC STETHOSCOPE OPERATING INSTRUCTIONS Individually handcrafted to the highest specifications by Goodman Bentley (Spec/Ops) Design & Security Company. Providers of covert Technical
More informationTNC Connectors. RF Coax Connectors. Product Facts
Product Facts Hex Crimp and Connectors 50 and 75 ohm commercial versions available Provides excellent performance at frequencies up to 7 GHz ow cost commercial type available type is smaller and lighter
More informationCOMPONENTS & COMPONENTS & ACCESSORIES
COMPONENTS & Accessories 135-145 135 COMPONENTS & ACCESSORIES REMOTE CONTROL 137-138 SOAP DISPENSERS 138 MIXING VALVES 139 SOLENOID KEY 140 REMOTE CONTROLS PERFECT TIME CONTROL ASSEMBLY 140 COVER PLATE
More informationAutomatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
More informationWFH SERIES Fluorescent High-Bay Lighting for Hazardous Locations
WFH SERIES W FH Fluorescent High-Bay Lighting for Hazardous Locations Class I, Division 2, Groups A, B, C, & D Class II, Division 2, Groups F & G Class III UL Listed for Wet & Hazardous Locations CUL Listed
More informationMagnecraft Power Relays
Description DPST-NO, 30 A; DPDT, 30 A (NO) / 3 A (NC) Description The series power relays offer a small package size and features Class F insulation for a maximum coil temperature of 55 C (3 F). These
More informationSlot-type Photomicrosensor with connector or pre-wired models (Non-modulated) *1. configuration. Dark-ON/Light-ON
Slot-type Photomicrosensor with connector or pre-wired models (Non-modulated) * EE-SX/6 Photomicrosensor with 0- to 00-mA direct switching capacity for built-in application. Series includes models that
More informationSoft starter, 66 A, V AC, Us= 24 V DC, with control unit, Frame size N. Function Soft starter for three-phase loads, with control unit
DATASHEET - S811+N66N3S Delivery program Soft starter, 66 A, 200-600 V AC, Us= 24 V DC, with control unit, Frame size N Part no. S811+N66N3S Catalog No. 168978 Eaton Catalog No. S811PLUSN66N3S EL-Nummer
More informationGATES AMPLIFIERS. Plug -in. Audio. Solid- Statesman Series HARRIS INTERTYPE CORPORATION. Six Premium Quality Transistorized Products
Six Premium Quality Transistorized Products 6300 Series Solid- Statesman Audio HARRIS INTERTYPE CORPORATION GATES AMPLIFIERS THE GATES M -6337 TELEVISION AUDIO CON- TROL CONSOLE marks a significant advance
More informationHigh performance circuit breakers
Series High performance Description The high performance MCB offers a compact solution to circuit protection. The devices are DIN rail mounted. The is available with application-specific trip characteristics
More informationEXLUX ECOLUX C-LUX 6480 Series
EXLUX ECOLUX C-LUX 6480 Series 6000 6008 6400 6408 6600 6608 6500 6480 Explosion Protected Fluorescent Luminaires for Hazardous and Corrosive Applications Features: Electronic Ballasts For Fluorescent
More informationSCALE & WEIGHT DISPLAYS
The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters
More informationInstallation Guide VL-MV10. Model No.
Installation Guide Model Name Model No. Main Monitor Station VL-MV0 R Main monitor station is described as "main monitor" in this guide. R In this guide, the suffix of each model number (e.g., the "EX"
More informationUltra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.mm Mated Height U.FL Series Up to 6GHz Transmission Speed Mated Height Comparison (With E.FL series) 1.9(2.0Max) U.FL-LP(V)-00 2.(2.5Max)
More informationDMP 335. Industrial Pressure Transmitter. Welded, Dry Stainless Steel Sensor. accuracy according to IEC 60770: 0.5 % FSO.
DMP 5 Industrial Pressure Transmitter Welded, Dry Stainless Steel Sensor accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 6 bar up to 0... 600 bar Output signals -wire: 4... 0 ma -wire:
More informationLighting: Fluorescent Lighting FD Series: Cylindrical Fluorescent Lighting Fixtures, Standard and Emergency Battery Back-Up Flameproof
ighting: Fluorescent ighting FD Series: Cylindrical Fluorescent ighting Fixtures, Standard and Emergency Battery Back-Up Flameproof 2 x 58 W Compliance Data: ATEX IECEx: ATEX IECEx CE Ex d IIB Ex d IIC
More informationLinear flow control with actuator IFC
Linear flow control with actuator Product brochure GB 3 Edition 01.14 Linear relationship between adjustment angle and flow rate Large control ratio of 25:1 EC type-tested and certified Actuators IC 20
More informationALLEN BRADLEY TIMING RELAY
ALLEN BRADLEY TIMING RELAY Configuration Details Product: 700-HS12BA1 Description: 700-HS General Purpose Square Base Timing Relay, On Delay Timer, 1.0 to 180 seconds, DPDT, 120V AC 50/60Hz CONTROL RELAY
More informationWeekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N
Weekly Timer 1/4 DIN Size Timer Features Prompted Programming and Large LCD Display 24 hours x 7 days programming using just 5 switches 16 program steps and cycle operation Two independent 15 A control
More informationFeatures. Specifications. Finish. Notes
Spec-00732 BPH FX ( McLean Electronics Cooling Sealed Enclosure Cooling McLean Electronics Cooling: Sealed Enclosure Cooling SPECTRACOOL Narrow Indoor/Outdoor N43 11000 BTU/Hr. 3223 Watt N36 / BTU/Hr.
More informationType Contact form Model Ag (Au clad) Standard DPDT G6A-274P-ST-US Low-sensitivity DPDT G6A-274P-ST40-US
Low Signal Relay G6A Fullly Sealed Relay with High Impulse Withstand High sensitivity can be driven by digital circuits. Low-profile design allows use in 12.70 mm PC board rack. Surge withstand meets FCC
More informationT-Series Indoor/Outdoor Air Conditioners. Keeps its cool during peak heat loads and hot weather. Product Overview. T-Series A/C
: Product Overview Keeps its cool during peak heat loads and hot weather A/C Indoor/Outdoor Air Conditioners Chapter Contents PRODUCT OVERVIEW T15 Model 800 BTU...43 Indoor/Outdoor Air Conditioners...42
More informationPulse Counters, electromechanical
Mini Counters W 5 / AW 5 5-digit miniature pulse counter, adding with manual reset Power consumption min. 30 mw Suitable for battery and electronic switching operations Long operating life (50 Mio. pulses)
More informationIllustrated Feature. Options
Applications Enclosed and gasketed fixtures for use where vapors, moisture, dirt or corrosive atmospheres are encountered. For use in hazardous locations defined by the NEC as Class I, Division 2. Groups
More informationSeries CT7N Bimetallic Overload Relays
Series CT7N imetallic Overload Relays Choose CT7N overloads in DC applications and when monitoring Variable Frequency Drives Sprecher + Schuh has always paid particular attention to the subject of motor
More informationInductive sensor. 2-wire, analog output BI8-M18-LI-EXI
ATEX category II 1 G, Ex-zone 0 ATEX category II 2 D, Ex-zone 21 Threaded barrel, M18 x 1 Chrome-plated brass 2-wire, 14 30 VDC Analog output 4 20 ma Cable connection Wiring diagram Type code Ident no.
More informationNessie Coils for VDH and VDHT valves
Data Sheet Nessie Coils for VDH and VDHT valves Introduction The coils for the Danfoss High-Pressure Systems valves are high-performance and reliable coils based on more than 50 years manufacturing of
More informationImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL
SPECIFICATIONS MODEL NUMBER: XRT910-0-0-GB-XX XRT911-0-0-GB-XX XTT911-0-0-NN-XX IMPROX TRT ImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL Working Environment XRT910-0-0-GB-XX... (Aluminium Extruded
More informationLC1D150B7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 150 A - 24 V AC 50/60 Hz coil
Product data sheet Characteristics LC1D150B7 TeSys D contactor - 3P(3 NO) - AC-3 -
More informationOPTEVA 828 LOBBY ATM FRONT LOAD PLAN VIEW FRONT ELEVATION SIDE ELEVATION
L0 CALL -800--600 OPTEVA 88 LOBBY ATM FRONT LOAD WITH 0mm ( 6") CEN III AND CEN IV SAFE CONSULT WITH DIEBOLD INSTALLATION/SERVICE BRANCH FOR ADDITIONAL DETAILS AND INFORMATION. PLEASE SEE PLANNING AND
More informationE6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm
Low-cost Encoder with Diameter of 50 mm CSM DS_E An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. High-precision detection of automatic machine timing.
More informationIn-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide
In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The
More informationInductive sensor NI3-EG08K-Y1-H1341
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationElectronic MICROSTAT-T Temperature controller with digital indication for use with resistance thermometers and thermocouples Series 8650
M. K. JUCHHEIM GmbH & Co Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 E-mail: mail@jumo.net Internet: www.jumo.de
More informationInductive sensor BI1.5-EG08K-Y1
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 at HFT0 SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1
More informationPower and Cable Management Products Doorbells Digital Tester
Products Doorbells Digital Tester 13 Amp railing Sockets 13 Amp 1 ang Extension eads 13 Amp 2 ang Extension eads 13 Amp 4 ang Extension eads 13 Amp 6 & ang Extension eads 13 Amp 3 ang Switched Extension
More informationTender Report for Supply and installation of LAN in *Biomedical Imaging and Bioinformatics Lab*
Tender Report for Supply and installation of LAN in *Biomedical Imaging and Bioinformatics Lab* General Scope of Work: Supply and installation of Computer Laboratory setup in MIU Location of Installation:
More informationTeSys contactors. Model d. Type of contactor LC1- LC1- LC1- LC1- LC1-D115 & D09 D18 D25 D38 D40 D50 D95 LC1-D150 DT20 & DT25 DT32 & DT40
Characteristics Type of contactor LC- LC- LC- LC- LC-D & D09 D8 D2 D38 D40 D0 D9 LC-D0 DT20 & DT2 DT32 & DT40 Environment Rated insulation voltage (Ui) Conforming to IEC 947-4-, overvoltage category III,
More informationNon Magnetic Connectors
Non Magnetic Connectors Johnson Components builds coaxial connectors using innovative materials and design to provide Mil Spec Performance at a commercial price. Now we offer our Non Magnetic Connectors
More informationVDI structed cabling system and warning devices. Flashing and rotating lights. Industrial bells (P. 324) (P. 325) VDI structured cabling system
VDI structured cabling system P. 322 LCS patch panels and units Bells, sirens, buzzers and warning lights P. 324 Electromechanical sirens P. 325 Flashing and rotating lights VDI structed cabling system
More informationQuick-disconnect cables. Adjustable mounting brackets
MiniSafe File No. LR90200 Description A MiniSafe consists of an identical length transmitter and receiver, combined with an STI Universal or DuoSafe Controller and appropriate interconnecting cables. The
More informationPBC series. RoHS. Ready. IEC-Type Contactors & Accessories 9-80 Amp AC-3, Amp AC-1 AC Coils. P&B PBC Series IEC Type Contactors & Accessories
PBC series IEC-Type Contactors & Accessories 9-80 Amp AC-3, 25-125 Amp AC-1 AC Coils File E38802 (PBC) RoHS Ready Users should thoroughly review the technical data before selecting a product part number.
More informationSmall Circular Connector. JN1/JN2 Series. Dust Cap
COMPONENTS PRODUCT INFORMATION RoHS Compliant NEW Small Circular Connector JN1/JN2 Series Angle Plug CONNECTOR MB-0054-8 October 2009 [JN1] [JN2] [JN1] [JN2] Straight Plug Cable Connecting Individual Plug
More informationCylindrical Photoelectric Sensor CY-100 SERIES
Cylindrical Photoelectric Sensor CY-00 SERIES Listing (2 m cable length type only) Features Wide product range Shape: Standard type Side view type Connector: 2 m cable length type M2 plug-in connector
More informationMagnecraft General Purpose Relays 782 Power Series SPDT 20 A; DPDT 15 A
72 Power Series SPDT 20 A; DPDT 15 A UL listed when used with proper Magnecraft sockets The 72 Plug-in Power relays offer clear or full-feature covers with multiple mounting options and accessories. Feature
More informationPERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY (SERIES SMA (CABLED) - PLUG, PIN CONTACT, CLASS 2)
INCH-POUND MIL-PRF-39012/55G 6 February 2008 SUPERSEDING MIL-PRF-39012/55G 6 January 2006 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY (SERIES SMA (CABLED) -
More informationEXLUX ECOLUX 6480 Series
EXLUX ECOLUX 6480 Series L I G H T I N G 6000 6008 6400 6408 6600 6608 6480 Explosion Protected Fluorescent Luminaires for Hazardous and Corrosive Applications Features: Electronic Ballasts For Fluorescent
More informationModel DT-311J. And DT-311J-230V(AC) DIGITAL STROBOSCOPE INSTRUCTION MANUAL
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com Model DT-311J And DT-311J-230V(AC) DIGITAL STROBOSCOPE INSTRUCTION MANUAL 1. GENERAL The DT-311J DIGITAL
More informationLC1D150G7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 150 A V AC coil
Product data sheet Characteristics LC1D150G7 TeSys D contactor - 3P(3 NO) - AC-3 -
More informationR87B. Box Fan. Comprehensive Lineup of Single, Double, and Triple Axial Fans with Easy One-step Mounting. Ordering Information. Model Number Structure
Box Fan R87B CSM_R87B_DS_E_4_2 Comprehensive Lineup of Single, Double, and Triple Axial Fans with Easy One-step Mounting Mounts in a square cutout and conceals the hole-cut to simplify installation work.
More informationSERIES BNC 50, COAXIAL MINIATURE CONNECTORS
SERIES BNC 50, COAXIAL MINIATURE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER BNC is still one of the most popular connector series, featuring a two stud bayonet coupling mechanism, which is particularly
More information1993 Specifications CSJ , etc. SPECIAL SPECIFICATION ITEM CCTV Central Equipment
1993 Specifications CSJ 0922-33-042, etc. SPECIAL SPECIFICATION ITEM 8549 CCTV Central Equipment 1. Description. This Item shall govern for the furnishing and installation of closed circuit television
More informationHazard Gard EVLL Series Explosionproof LED Luminaires Class I, Division 1 factory-sealed LED luminaire for general illumination
Engineering Hazard Gard EVLL Series Explosionproof LED Luminaires Class I, Division factory-sealed LED luminaire for general illumination High-performance, high-brightness Hazard Gard EVLL LED Luminaire
More informationMPCE Monitoring, Machine Test Signal. Guard Mode, Remote Reset. Eact Channel Select and Floating Blanking. Adjustable mounting brackets
MicroSafe MCF4700 C US File No. LR90200 MicroSafe Flexible MCF4700-12, MCF4700-20, MCF4700-30 12 mm, 20 mm and 30 mm resolution versions Compact segmented light curtain 1.02 inch (26 mm) x 1.1 inch (28
More informationBy CHANNEL VISION. Flush Mount Amplifier A0350
Spkrs Local In IR In 24VDC A0350 10 The A0350 can be used with Channel Vision s CAT5 audio hubs to provide a powerful 50Watts per channel in the listening zone. Alternatively, the A0350 can be added to
More informationSPECIAL SPECIFICATION 2344 TMC Support Equipment
2004 Specifications CSJ 0912-00-488 SPECIAL SPECIFICATION 2344 TMC Support Equipment 1. Description. Furnish Traffic Management Center (TMC) support equipment in the City of Missouri City TMC location
More informationMAP110 AC-DC Series Data Sheet
Description Single-Output Model Selection VOLTAGE RANGE OUTPUT CURRENT OUTPUT CURRENT REGULATION REGULATION %p-p (NOTE 1) ACCURACY MAP110-1005 5V 4.95V to 5.50 16A 2 0.2% 1% 1% 5.09V to 5.11V MAP110-1012
More informationLC3D115M7 TeSys D - star delta starter - 3 x 3P (3 NO) A V AC coil
Characteristics TeSys D - star delta starter - 3 x 3P (3 NO) - 115 A - 220 V AC coil Main Range Product name Product or component type Device short name Contactor application Utilisation category Device
More informationXR47-24 Models 24 W/ F (43 W/ C)
CLIMAGUARD AIR-TO-AIR INDOOR XR20 Models 4 W/ F (7 W/ C) XR29-08 Models 8 W/ F (14 W/ C) XR29-18 Models 18 W/ F (32 W/ C) XR47-24 Models 24 W/ F (43 W/ C) XR47-35 Models 35 W/ F (63 W/ C) XR60-55 XR60-84
More information