Manual. HoTT Hornet 250 Tricopter No No C No CAM. Copyright Graupner/SJ GmbH

Size: px

Start display at page:

Download "Manual. HoTT Hornet 250 Tricopter No No C No CAM. Copyright Graupner/SJ GmbH"

Clarissa Stevenson
5 years ago
Views:

1 EN Manual HoTT Hornet 250 Tricopter No No C No CAM Copyright Graupner/SJ GmbH

3 Index Introduction... 4 Service Centre... 4 Intended use... 5 Package content... 5 Symbols explication... 6 Safety notes... 6 Installation... 9 Construction of the front arms... 9 Construction of the back arm... 9 Assembling the main chassis Installing the upper chassis plate Assembly of the head Installing the head Installing the FPV transmitter with the camera BEC on the upper chassis plate Installing the controller and the BEC Installing the receiver Installing the arms on the main chassis plate Schematic diagram Soldering the XT-60 connector Commissioning version CAM Commissioning version or C Receiver s binding Necessary pre-settings on the transmitter Initialization of the gyro in the receiver Installing the propellers First flight Using camera / transmitter version CAM LED function head Technical Data Replacement parts Firmware update receiver Declaration of conformity Notes on environmental protection Care and maintenance Warranty certificate / 28

4 Introduction Thank you very much for purchasing the Graupner HoTT Hornet. This Tricopter is extremely versatile. This manual is valid for all tricopters listed on the cover sheet. Read this manual carefully to achieve the best results with your HoTT Hornet and first of all to safely control your models. If you experience any trouble during operation, take the instructions to help or ask your dealer or Graupner Service Centre. Due to technical changes, the information may be changed in this manual without prior notice. Be always updated by checking periodically on our website, to be always uptodate with the products and firmwares. This product complies with national and European legal requirements. To maintain this condition and to ensure safe operation, you must read and follow this user manual and the safety notes before using the product! NOTE This manual is part of that product. It contains important information concerning operation and handling. Keep these instructions for future reference and give it to third person in case you gave the product. Service Centre Graupner Central Service Graupner/SJ GmbH Henriettenstraße 96 D Kirchheim/Teck Graupner USA 3941 Park Dr Suite El Dorado Hills, CA Servicehotline (+49) (0)7021/ Monday - Thursday: 9:15 am - 4:00 pm Friday: 9:15 am - 1:00 pm service@graupner.de Website: Phone: service@openhobby.com Graupner in Internet For the service centers outside Germany please refer to our web site 4 / 28

5 Intended use The HoTT Hornet is a remote controlled tricopter. Other components are required, depending on the version, to be able to use the HoTT Hornet. Punctual technical information about the components can be found in the Technical data section. The HoTT Hornet is designed exclusively to be used as a battery-powered, radio controlled model, any other use is not allowed. For any improper use no warranty or liability is accepted. Read through this entire manual before you attempt to assemble or use or use the HoTT Hornet. Graupner/SJ constantly works on the development of all products; we reserve the right to change the item, its technology and equipment. Target group HoTT Hornet is not a toy. It is not suitable for children under 14 years. For questions about radio-controlled models, please contact an experienced RC model expert or a RC model club. Package content Version C CAM Chassis C C C 2x MOTOR - S7049 S7049 1x MOTOR - S7050 S7050 3x ESC - S S Camera Camera BEC - - S OSD cable VM with SBEC - S8446 S8446 Propeller - 2x X3 2x X3 2x X3L 2x X3 2x X3 2x X3L Servo Receiver - - S1019 FPV module - - S8460 LED & module - - RGB LED Velcro cable tie R R Velcro and fleece tape - 20X X20 2EA pieces Set small parts / screws Camera cable( JR Y cable) Camera cable ( JR to ZHR 3P) / 28

6 Symbols explication! Always observe the information indicated by this warning sign. Particularly those which are additionally marked with the CAU- TION or WARNING. The signal word WARNING indicates the potential for serious injury, the signal word CAUTION indicates possibility of lighter injuries. The signal word Note indicates potential malfunctions. Attention indicates potential damages to objects. Thread lock This symbol shows that thread lock must be used. Pay attention to the hazard notices on the package. Soldering instructions this symbol shows that it is necessary to solder some parts. Shrink tube instruction This symbol shows that it is necessary to isolate with shrink tube. Safety notes WARNING! This safety notes are intended to protect you and other people. They are also used for safe handling the product. Therefore please read this section very carefully before using the product! Do not carelessly leave the packaging material lying around, since it might become a dangerous toy for children. Persons, including children, with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, or not capable to assemble and use safely the HoTT Hornet must not use the HoTT Hornet without supervision or instruction by a responsible person. Operation and use of radio-controlled models needs to be learned! If you have never operated a model of this type before, start carefully and make yourself familiar with the model's reactions to the remote control commands. Proceed responsibly. 6 / 28

7 Inform yourself before flying your model on which maximum altitude you can fly in the uncontrolled airspace over the starting position and do not exceed it. First, always perform a range and function test on the ground (to do so, hold your model tight), before you use your model. Repeat the test with running motor and with short throttle bursts. Before you start using the remote control model, you have to check the further relevant laws and regulations. These laws you must obey in every case. Pay attention to the possibly different laws of the countries. The insurance is mandatory for all kinds of model operation. If you already have one, so please inform yourself if the operation of the respective model is covered by your insurance. If this is not the case, conclude a special liability insurance policy for models. We recommend to provide the HoTT Hornet with a label, where are indicated the name, address, tel. n., and Insurance N. So that the copter can be clearly assigned in the event of a crash. Due to safety and licensing reasons (CE), any unauthorized reconstruction and/or modification of the product is prohibited. Only use the components and spare parts that we recommend. Always use matching, original Graupner plug-in connections of the same design and material. Make sure that all of the plug-in connections are tight. When disconnecting the plug-in connections, do not pull the cables. Protect the Copter from dust, dirt, moisture and other foreign parts. It must be protected from vibration as well as excessive heat or cold. The models may only be operated remotely in normal outside temperatures such as from -10 C to +55 C. Only operate all your HoTT components using the current software version. If you have questions which cannot be answered by the operating manual, please contact us (contact information see page 3) or another expert in the field. 7 / 28

8 WARNING! Safety notes during the use Also while programming, make sure that a connected electric motor cannot accidentally start. Injury risk by the turning propellers! Always remove the propellers when programming. Program always the motors stop switch on the transmitter. (See transmitter manual) Avoid shock and pressure. Check the HoTT Hornet regularly for damages to the housings and cables, specially after a crash of the model. Damaged or wet electronic components, even if re-dried, should no longer be used! Never touch the turning propellers, this can cause serious injury. The propellers must be mounted securely, thrown parts can cause serious injury. Keep long hair, loose clothing such as scarves, loose shirts or similar well away from the danger zone of the revolving propeller, they may be withdrawn by the propeller, flying debris can cause serious injury. Observe the safety notes of the required components. Note: After you perceive your model, check if all components are inside the package and eventual damages. Remove the battery from the model when transporting or when not in use. During transport protect the model and the transmitter from damages. The fron arms of the copter can be folded for transport. P Care: Clean the Copter, the battery and the charger only with the suitable cleaners. Good is a spirit-free cloth. Never use chemical cleaners, solvents, petrol, alcohol or similar. 8 / 28

9 Installation Note This assembling manual is valid for the version C and so as a guide for disassembling the CAM version in case of repair. Required accessories Allen key 1 and 1,5 mm Phillips screwdriver 1,5 mm Construction of the front arms Front arms, left / right 2x skids, front 1x Motor S7049, right arm 1x Motor S7050, left arm 4x Screws M3x8 4x Screws M3x14 Construction of the back arm Rear arm Nut M3 1 9 / 28

10 2 Rear skid 1x Screw M3x8 Lower motor holder 1x Ball bearing 1x collar ball bearing 3 Servo Upper motor holder 4 10 / 28

11 5 Servo holder 1x Screw M3x24 2x Screws M2x15 6 1x Motor S7049 2x Screws M3x5 11 / 28

12 Assembling the main chassis Lower left lateral part Lower right lateral part Main chassis plate 8x Screws M3x8 2x Spacer tubes Installing the upper chassis plate Upper left lateral part Upper right lateral part Upper chassis plate 4x Screws M3x8 4x Nuts M3 12 / 28

13 Assembly of the head Eye, left Eye, right 4x M1,7x4 1 2x Antenna tubes, curved 2 3 LED Glue pads 4x screws 1,5x4 13 / 28

14 4x M1,7x4 4 LED module Glue pads 5 3x M2x / 28

15 Installing the head 4x Screws M2x4 Installing the FPV transmitter with the camera BEC on the upper chassis plate 3x Cable ties 3x Glue pads 15 / 28

16 Installing the controller and the BEC 3x Controllers 1x VM with SBEC 4x Glue pads 4x Cable ties Installing the receiver 1x Receiver 1x Glue pad 2x Antenna tubes 16 / 28

17 Installing the arms on the main chassis plate 4x Screws M3x30 2x Screws M3x8 4x Nuts M3 17 / 28

18 Schematic diagram 1 Motor right 2 ESC right / channel Camera BEC 4 Camera 5 Transmitter 6 Receiver 7 VM+SBEC / Telemetry 8 ESC back / channel 3 9 Motor back 10 Servo / channel 4 11 Motor left ESC left / channel 1 13 SXM module / channel LED boards Soldering the XT-60 connector XT-60 connector 2x Shrink tubes Warning! Risk of injury by rotating propellers in case the motors start. Install the propellers only after the following programming. 18 / 28

19 Commissioning version CAM To start fling you need the following items: Transmitter HoTT (MX-12 / MZ-12 or higher) LiPo battery 3S, Graupner LiPo battery V-MAXX 50 C 3/1500 mah, No D35 Video goggles or LCD monitor Receiver The transmitter is already completely set for HoTT Hornet. To program some parameters, refer to the manual included with the receiver. Battery installation Fix the battery with the included velcro tape and the fleece pad into the battery case. Place the battery so that the tricopter s center of gravity is in the middle of the frame. Commissioning version or C These versions can be completed with different assembly parts, pay attention to the use of the different parts in the manual. We recommend the parts listed in the spare parts list because they are specifically made for the tricopter. Check the direction of rotation of the motors (see drawing on page 21). It is possible to change the direction of rotation by reversing 2 motor connection cables. Receiver s binding If you wish to bind the receiver to a new model memory, this is the procedure: Switch the transmitter s RF section off in the Basic model settings menu (see transmitter manual) Switch on the receiver and put it in binding mode, by pressing and holding the binding button (green and red LED on the receiver are flashing) Initiate binding in the transmitter s Basic model settings menu. If the red LED of the receiver goes out within about 10 seconds and the green LED is illuminated, the binding process has been completed successfully. Your transmitter/receiver combination is now ready for operation. If the red LED is still lit, the "binding failed. In this case, repeat the whole procedure. 19 / 28

20 Necessary pre-settings on the transmitter In the transmitter it must be selected a free model memory, the model type must be surface model and the channel 1 direction must be set so that in motor off position the power indicator must show -100%. The flight mode must be set on channel 5. Then program a 2 way switch for channel 5 to control the flight mode: Attitude mode: Channel 5 = -100% to +50%. The stick movement influences the HoTT Hornet reaction on Roll and Nick. It allows a maximal angle of about 50 at 100% of stick movement. Mode suggested for beginners. The stick movements acts directly proportionally to Roll and Nick. Rate mode: Channel 5 = more than +50%. The stick movement influences the rate without angle limit. Aerobatic mode that allows rolls and loopings. Do not forget to set the failsafe up! We suggest to set the fail-safe on channel 5 and channel 1 at -100%, so that in fail safe it is active the attitude mode. Program the motor stop switch! Program always the motors stop switch on the transmitter. (See transmitter manual) This prevents accidental starting of motors, thus reducing the risk of injury. Initialization of the gyro in the receiver Once the HoTT Hornet has been switched on, the gyro immediately becomes active but still needs to be initialized. To initialize the gyro, keep your HoTT Hornet still when you switch it on. The calibration process can only be performed when the receiver is absolutely still. After 3 seconds in still position you will hear beeps emitted by all motors. These "wiggles" signal that initialization has been successful and that calibration is complete. Always wait until the calibration process has finished before starting to fly the model. Safety function - motors-off The motors will not start until the calibration is successfully completed. Auto-flip function version CAM The auto-flip function allows you to flip your copter in a very easy way. It is essential that you control in Attitude mode (function not allowed in Rate mode). The auto-flip function is controlled by a switch assigned to channel 6. (see manual S1019) Activate the switch and within 5 sec move the nick or roll stick to more than 50% of its course, then the copter makes autonomously a flip in the selected direction. After the flip it is possible to have some little position movements (<10 ) 20 / 28

21 Installing the propellers Warning! Risk of injury by rotating propellers in case the motors start. Always unplug the XT-60 connector to the LiPo battery before working on the propellers. Install the propellers as shown in the picture below. Pay attention to install the proper propeller to each motor. The propeller rotation sense is written on the propeller (R/L)! The image represents the copter seen from the top. 1 2 Tri L 3 R+L= Servo direction Servo 4= Yaw Pos x3 R C-Prop yellow Pos x3 L C-Prop yellow Pos x3 L C-Prop red First flight First flight in Attitude mode! Switch the transmitter on and plug the battery to prepare the HoTT Hornet to fly. Unfold the arms completely and make sure they are in the correct position. Choose a free area for your first flight. Select first always the Attitude mode because so the copter is easier to control. Take firstly confidence with the flight attitude of the HoTT Hornet. Proceed carefully and responsibly. The included Voltage module with SBEC offers you the possibility to set up to three different voltage alarms in steps of 0,1 V. Thus read the manual of the module and of your HoTT transmitter. 21 / 28

22 Using camera / transmitter version CAM Camera and transmitter are assembled and connected. Scan the transmitter's frequency in your suitable optional video goggle or video monitor. The video signal transmission begins as soon as the battery is connected. The channel of the transmitter is factory set to channel 01. If you want to change the transmitting channel of the transmitter, proceed as follows: Set the micro-switch bar on the transmitter circuit board according to the included manual for the desired channel. Video transmitter technical data No. S8460 Operating voltage DC (V): 7-22,2 (3S LiPo) Width [mm]: 24 Height [mm]: 12 Length [mm]: 35 Frequency GHz: 5,8 Channels: 22 Output mw: 25 Weight [g]: 12 LED function head Version CAM In the head of the HoTT Hornet there is a LED illumination of the eyes. The color of the LEDs can be changed through a specifically programmed control on the channel 6 of the transmitter. Read the manual included with the Switch module SXM No Version In the head of the HoTT Hornet there is a LED illumination of the eyes. Connect the SXM module to a free channel of the receiver. Program a control for this channel on your transmitter. Then you can switch the colors of the LEDs. (see SXM module manual) 22 / 28

23 Technical Data ULTRA KV Brushless Motor (clockwise and counter-clockwise) Turns/Volt KV Diameter - 28mm Input voltage - 2-4S LiPo Shaft diameter - 5mm (clockwise and counter-clockwise) Speed controller Ultra Control 20A Race Input voltage - 2-4S LiPo Dimensions - 22x12x5 mm Weight - 7 grams Maximal current - 20A without BEC Voltage module+sbec Operational voltage - 7,4 to 22,2 V BEC voltage - 4,5 to 8V Dimensions - 35x17x7 mm Weight - 8 grams Receiver GR-18C Operating temperature: C Antennas: 2 x wires 145 mm Total weight approx.: 14 g Frequency: MHz Range approx.: 4000 m Dimensions ca.: 46 x 21 x 14 mm Modulation: 2.4 GHz FHSS Current consumption: 70 ma Operating voltage: (2,5) 3,6... 8,4 V x3 R+L propellers Ø/Pitch: 15/7,5 cm Weight ca.: 4.0 g Ø/pitch: 6/3 " Color: red or yellow Chassis Axle distance: 25 cm Chassis height: 9 cm Folding arms Weight:395 g 23 / 28

24 Replacement parts 1x Hornet head 1x LED eye left/right 1x Landing frame 1x Copter arm front left 1x Copter arm front right 1x Copter arm rear 1x Main chassis plate 1x Upper chassis plate 1x Upper left lateral part 1x Upper right lateral part 1x Lower left lateral part 1x Lower right lateral part 4x Upper motor mount 6x Lower motor mount 8x Set aluminum spacers 5x Set screws/small parts 2x S7049 MOTOR 1 1x S7050 MOTOR 2 3x S ESC 1x #4 Camera 1x S Camera BEC 1x OSD cable 1x S8446 VM with SBEC 2x X3R red Propeller 2x X3L yellow 2x X3L yellow 1x Servo 1x S1019 Receiver GR-18C 1x S8460 FPV module 1x 3971.RGB Illumination set RGB 1x R Velcro cable tie 2x 20X20 Velcro and fleece tape 1x LED illumination rear 24 / 28

Firmware update receiver Updates to the receiver s firmware are made via the telemetry socket using a PC running Windows XP, Vista or 7. You will also need a USB interface, order No. 7168.

25 Firmware update receiver Updates to the receiver s firmware are made via the telemetry socket using a PC running Windows XP, Vista or 7. You will also need a USB interface, order No , and adapter lead, order No A or 7168.S, which are available separately. The programs and files required can be found in the Download area for the corresponding products at Connect the adapter lead to the USB interface No The connectors are reverse polarity protected: note the small chamfers on the sides. Never use force the connectors should engage easily. Connect the adapter lead to the receiver's telemetry socket. The connectors are reverse polarity protected: note the small chamfers on the sides. Never use force the connectors should engage easily. Starting the "Slowflyer/Gyro receiver update" We recommend accessing the "Slowflyer/Gyro receiver update" program from the "Firmware_Up-grade_grStudio" program. Click on the "Receiver Downloader" item under "Link" in the left function menu. (Alternatively, select the "Micro Receiver Upgrade" under "Menu"). It is also possible to start the associated application program directly. By double-clicking on the file micro_gyro_swloader. exe. You will find this.exe file in the "Graupner_ PC Software" folder of the "HoTT_Software VX" package. A program window will now appear in which you should first set the "correct" COM port for the USB interface No in the selection window. If you are not sure which port to use, check the COM port in the "Select Port" window in the "Menu" of the "Firmware_Up-grade_ grstudio" and note down the COM port number for the "Silicon Labs CP210x USB to UART Bridge" entry in this case "COM03". (If you select the wrong port, you will be alerted to this when you read out the receiver data). 25 / 28

Click on "File" to load the corresponding firmware file named "MicroStabi7X_V_XX.bin" from the hard disc ("XX" stands for the version number). When the file has loaded, click on start.

26 Click on "File" to load the corresponding firmware file named "MicroStabi7X_V_XX.bin" from the hard disc ("XX" stands for the version number). When the file has loaded, click on start connect the receiver and switch it on. The progress bar shows that the transfer is running normally. The receiver LED lights up red and green during this process and flashes red and green alternately once the transfer is complete. Please refer to the detailed update instructions for the item in question in the Download area at Declaration of conformity HoTT Hornet Graupner/SJ declares that the product is conform to EU norms. EN 62479:2010 EN :2006+A11:2009+A1:2010+A12:2011+A2:2013 EN V1.9.2; EN V1.6.1 EN V1.6.1; EN V1.4.1 EN V1.9.1 The Declarations of conformity of the single components are included in the manuals of the related components. 26 / 28

27 Notes on environmental protection Disposal notes This symbol on the product, user manual or packaging indicates that this product must not be disposed of with other household waste at the end of its life. It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. The materials are recyclable as marked. By recycling, material reusing or other forms of scrap usage you are making an important contribution to environmental protection. Batteries and accumulators must be removed from the device and disposed of at an appropriate collection point. Please inquire if necessary from the local authority for the appropriate disposal site. Care and maintenance P Notes on care The product does not need any maintenance, it works so as it is without any special care. In your own interests protect it from dust, dirt and moisture. Warranty certificate The Graupner, Henriettenstrassee 96, Kirchheim/Teck grants from the date of purchase of this product for a period of 24 months. The warranty applies only to the material or operational defects already existing when you purchased the item. Damage due to misuse, wear, overloading, incorrect accessories or improper handling are excluded from the guarantee. The legal rights and claims are not affected by this guarantee. Please check exactly defects before a claim or send the product, because we have to ask you to pay shipping costs if the item is free from defects. The present construction or user manual is for informational purposes only and may be changed without prior notice. The current version can be found on the Internet at on the relevant product page. In addition, the company Graupner has no responsibility or liability for any errors or inaccuracies that may appear in construction or operation manuals. No liability can be accepted for printing errors. 27 / 28

Manual. HoTT Hornet 250 Tricopter with mz-12 transmitter No RTF. Copyright Graupner/SJ GmbH

Manual. HoTT Hornet 250 Tricopter with mz-12 transmitter No RTF. Copyright Graupner/SJ GmbH EN Manual HoTT Hornet 250 Tricopter with mz-12 transmitter No. 16540.RTF Copyright Graupner/SJ GmbH Index Introduction... 4 Service Centre... 4 Intended use... 5 Package content... 5 Symbols explication...