User Manual IDM-1104HN-35XGA1E(XGA) 10.4 TFT Liquid Crystal Display Module

Transcription

1 User Manual IDM-4HN-35XGAE(XGA).4 TFT Liquid Crystal Display Module

2 Copyright The documentation and the software included with this product are copyrighted 26 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details. If you think you have a defective product, follow these steps. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available. 3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. Part No. 264 Edition Printed in Taiwan February 26 IDM-4 User Manual ii

3 Technical Support and Assistance. Visit the Advantech website at http//support.advantech.com where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application software, etc.) A complete description of the problem The exact wording of any error messages Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. Note! Notes provide optional additional information. Document Feedback To assist us in making improvements to this manual, we would welcome comments and constructive criticism. Please send all such - in writing to support@advantech.com Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 8pcs LCD modules / Box Box dimensions 465 (L) X 362 (W) X 34 (H) mm Weight approximately 8.3Kg (8 modules per box) iii IDM-4 User Manual

4 Safety Instructions. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord.. All cautions and warnings on the equipment should be noted.. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 2. Never pour any liquid into an opening. This may cause fire or electrical shock. 3. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 4. If one of the following situations arises, get the equipment checked by service personnel The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. 5. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -2 C (-4 F) OR ABOVE 6 C (4 F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. 6. CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. The sound pressure level at the operator's position according to IEC is no more than 7 db (A). DISCLAIMER This set of instructions is given according to IEC 74-. Advantech disclaims all responsibility for the accuracy of any statements contained herein. IDM-4 User Manual iv

5 Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components. PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS. Do not apply rough force such as bending or twisting to the module during assembly. 2. It is recommended to assemble or to install a module into the user s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. 3. Do not apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight. 4. Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. 5. Do not plug in or pull out the I/F connector while the module is in operation. 6. Do not disassemble the module. 7. Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. 8. Moisture can easily penetrate into LCD module and may cause the damage during operation. 9. High temperature or humidity may deteriorate the performance of LCD module. Please store LCD modules in the specified storage conditions.. When ambient temperature is lower than ºC, the display quality might be reduced. For example, the response time will become slow, and the starting voltage of backlight will be higher than that of room temperature.. Do not keep same pattern in a long period of time. It may cause image sticking on LCD. SAFETY PRECAUTIONS. The startup voltage of a Backlight is approximately Volts. It may cause an electrical shock while assembling with the inverter. Do not disassemble the module or insert anything into the Backlight unit. 2. If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. 3. After the module s end of life, it is not harmful in case of normal operation and storage. v IDM-4 User Manual

6 IDM-4 User Manual vi

7 Contents Chapter General Description.... Overview Features Application General Specifications Mechanical Specifications Dimensions... 3 Chapter 2 Absolute Maximum Ratings Absolute Ratings Of Environment Electrical Absolute Ratings TFT LCD Module LED Converter... 7 Chapter 3 Electrical Characteristics TFT LCD Module LED Converter... 2 Chapter 4 Block Diagram TFT LCD Module... 4 Chapter 5 Interface Pin Assignment TFT LCD Module Backlight Unit (Converter Connector Pin) Color Data Input Assignment... 7 Chapter 6 Interface Timing Input Signal Timing Specifications Power ON/OFF Sequence The Input Data Format Scanning Direction Chapter 7 Optical Characteristics Test Conditions Optical Specifications Chapter 8 Reliability Test Criteria Reliability Test Criteria Chapter 9 Packaging...33 vii IDM-4 User Manual

8 9. Packing Method IDM-4 User Manual viii

9 Chapter General Description

10 . Overview IDM-4HN-35XGAE(XGA) is made by Innolux G4X-L3 which is a.4" TFT Liquid Crystal Display module with LED backlight unit and 3-pin-and-ch LVDS interface. This product supports 24 x 768 XGA format and can display true 6.2M colors (6-bits colors with FRC). The converter module for LED backlight is built-in..2 Features Excellent brightness (35 nits) Ultra high contrast ratio () Fast response time (T on +T off average 25 ms) High color saturation NTSC 57% XGA (24 x 768 pixels) resolution DE (Data Enable) only mode LVDS (Low Voltage Differential Signaling) interface Ultra wide viewing angle 76(H)/ 76(V) (CR>) Super MVA technology 8 degree rotation display option Color reproduction (Nature color) Wide operation and storage temperature range.3 Application TFT LCD monitor for Industrial applications Slim design display for portable applications Digitizer Applicable Design.4 General Specifications Item Specification Unit Note Active Area 2.4 (H) x 57.8 (V) (.4 diagonal) mm () Bezel Opening Area 25.4 (H) x 6.8 (V) mm Driver Element a-si TFT active matrix - - Pixel Number 24 x R.G.B. x 768 pixel - Pixel Pitch (Sub Pixel).685 (H) x.255 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 6.2 M color - Display Operation Mode Transmissive mode / Normally black - - Surface Treatment Anti Glare - - Total power consumption (typ) 5. W typ Note! Please refer to the attached drawings for more information of front and back outline dimensions. IDM-4 User Manual 2

11 .5 Mechanical Specifications Item Min. Typ. Max. Unit Note Horizontal (H) mm () Module Size Vertical (V) mm Depth (D) mm - Weight g - Note!.6 Dimensions ±.5 (Max) Please refer to the attached drawings for more information of front and back outline dimensions Ø2.8 User Hole ± ±.2 (Opening Area) Active Area (2.432 x ) XC C 75.8 ± ±.2 (Opening Area) Chapter General Description Active Area Center IDM-4 User Manual

12 IDM-4 User Manual 4

13 Chapter 2 2Absolute Maximum Ratings

14 2. Absolute Ratings Of Environment Value Item Symbol Min. Max. Unit Operating Ambient Temperature T OP ºC Storage Temperature T ST ºC Note Note!. Temperature and relative humidity range is shown in the figure below. 9 %RH Max. (Ta 4 ºC). Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). No condensation Relative Humidity (%RH) Operating Range 4 2 Storage Range Temperature (ºC) 2.2 Electrical Absolute Ratings 2.2. TFT LCD Module Value Item Symbol Unit Note Min. Max. Power Supply Voltage VCC V () IDM-4 User Manual 6

15 2.2.2 LED Converter Item Symbol Value Min. Max. Unit Note Converter Voltage V i V (), (2) Enable Voltage EN V Backlight Adjust ADJ V Note! Note2! Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Specified values are for LED light bar (Refer to 3.2 for further information). Chapter 2 Absolute Maximum Ratings 7 IDM-4 User Manual

16 IDM-4 User Manual 8

17 Chapter 3 3Electrical Characteristics

18 3. TFT LCD Module Ta = 25 ± 2 ºC Value Parameter Symbol Min. Typ. Max. Unit Note Power Supply Voltage VCC V () Rush Current IRUSH A (2) Power Supply Current Black ma White ma - (3) Power Consumption PL W LVDS differential input voltage VID - 6 mv - LVDS common input voltage VICM V - Note! Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note2! Specified values are for LED light ba (Refer to 3.2 for further information). +3.3V Q 2SK475 FUSE C3 Vcc (LCD Module Input) R uf 47K (High to Low) (Control Signal) SW R2 Q2 2SK47 +2V K VR 47K C2 C.uF uf IDM-4 User Manual

19 GND VCC rising time is 47us.Vcc.9Vcc 47μs +3.3V Note! The specified power supply current is under the conditions at V cc = 3.3 V, T a = 25 ± 2 ºC, f v = 6Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern Chapter 3 Electrical Characteristics Active Area Active Area c. Vertical Stripe Pattern R G B R G B B R G B R G B R B R G B R G B R R G B R G B Active Area IDM-4 User Manual

20 3.2 LED Converter Ta = 25 ± 2 ºC Value Parameter Symbol Unit Note Min. Typ. Max. Converter Power Supply Voltage V i V (Duty %) Converter Power Supply Current I i A LED Power Consumption P LED W EN Control Level Backlight on Backlight off V V PWM Control Level PWM High Level V PWM Low Level V PWM Control Duty Ratio 2 % PWM Control Frequency f PWM 9 2 2k Hz (2) LED Life Time L L 3, Hrs Vi = 2V (Duty Vi = 2V (Duty %) Note! LED current is measured by utilizing a high frequency current meter as shown below Note2! At 9 ~KHz PWM control frequency, duty ratio range is restricted from 2% to %. K ~2KHz PWM control frequency, minimum duty on-time 2 us. Note3! The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 C and I LED = 2mADC (LED forward current) until the brightness becomes 5% of its original value. Operating LED under high temperature environment will reduce life time and lead to color shift. Input Power Pi Output Power Po Power Supply Vi, Ii GND Converter Vo, Io LED Backlight Unit IDM-4 User Manual 2

21 Chapter 4 4Block Diagram

22 4. TFT LCD Module RX(+/-) RX(+/-) RX2(+/-) RX3(+/-) RXCLK(+/-) VCC SEL 6/8 RPFI GND (JAE,FI-XB3SRL-HF) INPUT CONNECTOR TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE SCAN DRIVER IC TFT LCD PANEL (24x3x768) DATA DRIVER IC Vi CONVERTER CONNECTOR (Connector, 928-,.mm, WTB, pin, Aces) Converter LED BACKLIGHT UNIT IDM-4 User Manual 4

23 Chapter 5 5Interface Pin Assignment

24 5. TFT LCD Module CN Connector Pin Assignment Pin No. Symbol Description Note VCC - Power supply +3.3V - 2 VCC Power supply +3.3V - 3 VCC VCC Power supply +3.3V - 4 GND Ground - 5 GND Ground - 6 GND Ground - 7 RPFI Reverse Panel Function (Display Rotation) 8 NC No Connection 9 NC No Connection NC No Connection SEL6/8 LVDS 6/8 bit select function control, Low or NC -> 8 bit Input Mode ( 2 ) High -> 6bit Input Mode 2 GND Ground - 3 NC No Connection - 4 GND Ground - 5 RX- Negative transmission data of pixel - 6 RX+ Positive transmission data of pixel - 7 GND Ground - 8 RX- Negative transmission data of pixel - 9 RX+ Positive transmission data of pixel - 2 GND Ground - 2 RX2- Negative transmission data of pixel 2-22 RX2+ Positive transmission data of pixel 2-23 GND Ground - 24 RXCLK- Negative of clock - 25 RXCLK+ Positive of clock - 26 GND Ground - 27 RX3- Negative transmission data of pixel 3-28 RX3+ Positive transmission data of pixel 3-29 GND Ground - 3 NC No Connection ( 2 ) ( 2 ) Note! Connector Part No. JAE, FI-XB3SRL-HF or compatible connector Note2! Low stands for V. High stands for 3.3V. NC stands for No Connected IDM-4 User Manual 6

25 7 IDM-4 User Manual Chapter 5 Interface Pin Assignment 5.2 Backlight Unit (Converter Connector Pin) 5.3 Color Data Input Assignment The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Pin Symbol Description Remark Vi Converter input voltage 2V 2 Vi Converter input voltage 2V 3 Vi Converter input voltage 2V 4 Vi Converter input voltage 2V 5 VGND Converter ground Ground 6 VGND Converter ground Ground 7 VGND Converter ground Ground 8 VGND Converter ground Ground 9 EN Enable pin 3.3V ADJ Backlight Adjust PWM Dimming Color Data Signal Red Green Blue R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253 ) Red(254 ) Red(255 ) Gray Scale Of Green Green() / Dark Green() Green(2) Green(2 53) Green(2 54) Green(2 55)

26 IDM-4 User Manual 8 Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253 ) Blue(254 ) Blue(255 ) Note! Low Level Voltage, High Level Voltage

27 Chapter 6 6Interface Timing

28 6. Input Signal Timing Specifications The input signal timing specifications are shown as in the following table and timing diagram. Signal Item Symb ol Min. Typ. Max. Unit Note DCLK Frequency Fc MHZ Vertical Active Display Term Horizontal Active Display Term Total Tv Th Tv=Tvd+T vb Display Tvd Th - Blank Tvb Th - Total Th Tc Th=Thd+T hb Display Thd Tc - Blank Thb Tc - Note! Since this assembly is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally. Note2! Frame rate is 6Hz INPUT SIGNAL TIMING DIAGRAM Tv Tvd Tvb DE Th DCLK DE Tc Thb Thd DATA Valid display data IDM-4 User Manual 2

29 6.2 Power ON/OFF Sequence To prevent a latch-up or DC operation of LCD assembly, the power on/off sequence should be as in the diagram below..vcc VCC LVDS Vi.9VCC.9Vi.Vi BL ON/OFF PWM DIMMING T T2 T5 T8 VALID T9 T6 9% % T3 9% % 9% % T7.9VCC.VCC T4.9Vi.Vi Chapter 6 Interface Timing Power ON/OFF sequence Note! Please avoid floating state of interface signal at invalid period. Note2! When the interface signal is invalid, be sure to pull down the power supply of LCD VCC to V. Note3! The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Parameter Value Min Typ Max Units T.5 - ms T2-5 ms T3-5 ms T ms T ms T ms T7 5-3 ms T8 - - ms T9 - - ms 2 IDM-4 User Manual

30 6.3 The Input Data Format Note! R/G/B data 7 MSB, R/G/B data LSB Note2! Please follow PSWG Signal Nme Description Remark R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G Red Data7(MSB) Red Data6 Red Data5 Red Data4 Red Data3 Red Data2 Red Data Red Data(LSB) Green Data7(MSB) Green Data6 Green Data5 Green Data4 Green Data3 Green Data2 Green Data Green Data(LSB) Red-pixel Data Each red pixel data consists of these 8 bits pixel data. Green-pixel Data Each green pixel data consists of these 8 bits pixel data. IDM-4 User Manual 22

31 B7 B6 B5 B4 B3 B2 B B RXCLKIN+ RXCLKIN- DE VS HS Note3! Blue Data7(MSB) Blue Data6 Blue Data5 Blue Data4 Blue Data3 Blue Data2 Blue Data Blue Data(LSB) LVDS Clock Input Display Enable Vertical Sync Horizontal Sync 6.4 Scanning Direction Blue-pixel Data Each blue pixel data consists of these 8 bits pixel data. Output signals from any system shall be low or Hi-Z state when VCC is off Chapter 6 Interface Timing The following figures show the image see from the front view. The arrow indicates the direction of scan. RPFI = Low/floating; normal display (default) RPFI = high display with 8degree rotation 23 IDM-4 User Manual

32 IDM-4 User Manual 24

33 Chapter 7 7Optical Characteristics

34 7. Test Conditions Item Symbol Value Unit Ambient Temperature Ta 25±2 oc Ambient Humidity Ha 5± %RH Supply Voltage Vcc 5 V According to typical value in "3. ELECTRICAL CHARACTERIS- Input Signal TICS" Converter Current I L 2±mA ma 7.2 Optical Specifications The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7. and stable environment shown in Note (6). Item Symbol Condition Min. Typ. Max. Unit Note Contrast Ratio CR 7 - (2) TR ms Response Time (3) TF - 6 ms Center Luminance of White LC cd/m 2 (4) White Variation δw (7) Cross Talk CT % (5) θ x =, θ Y = Rx.6 - Red Viewing angle at Ry normal direction Gx.34 - Green Gy Typ..564 Typ. - Chromaticity (6) Bx Blue By.87 - Viewing Angle White Horizontal Vertical Wx.33 - Wy θ x θ x CR θ Y θ Y Deg. () IDM-4 User Manual 26

35 Note! Note2! X- = 9º 6 o clock y- = 9º Definition of Viewing Angle (θx, θy) Viewing angles are measured by BM5A x- y- Normal x = y = º x y x 2 o clock direction y+ = 9º y- x+ Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7). y+ X+ = 9º Chapter 7 Optical Characteristics Note3! Definition of Response Time (T R, T F ) % 9% Gray Level 255 Gray Level 255 Optical Response % Gray Level % T F T R Time 27 IDM-4 User Manual

36 Note4! Definition of Luminance of White (L C ) Measure the luminance of gray level 255 at center point and 5 points L C = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note5! Definition of Cross Talk (CT) CT = Y B Y A / Y A (%) Where Y A = Luminance of measured location without gray level pattern (cd/ m 2 ) Y B = Luminance of measured location with gray level pattern (cd/m 2 ) (, ) Active Area Y A, U (D/2,W/8) (, ) Active Area Y B, U (D/2,W/8) (D/4,W/4) Y A, L (D/8,W/2) Y A, D (D/2,7W/8) Gray 28 Y A, R (7D/8,W/2) Y B, L (D/8,W/2) Y B, D (D/2,7W/8) Gray Gray 28 Y B, R (7D/8,W/2) (3D/4,3W/4) (D,W) (D,W) Note6! Measurement Setup The LCD assembly should be stabilized at given temperature for 3 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 3 minutes in a windless room. LCD Module LCD Panel USB2 CS-T Center of the Screen 5 mm Light Shield Room (Ambient Luminance < 2 lux) IDM-4 User Manual 28

37 Note7! Vertical Line W Definition of White Variation (ᴽW) Measure the luminance of gray level 255 at 5 points ᴽW = Maximum [L (), L (2), L (3), L (4), L (5)] / Minimum [L (), L (2), L (3), L (4), L (5)] W/4 W/2 3W/4 Horizontal Line D D/4 D/2 3D/4 3 5 Active Area 2 4 X Test Point X= to 5 Chapter 7 Optical Characteristics 29 IDM-4 User Manual

38 IDM-4 User Manual 3

39 Chapter 8 8Reliability Test Criteria

40 8. Reliability Test Criteria Test Item Test Condition Note High Temperature Storage Test 7ºC, 24 hours Low Temperature Storage Test -2ºC, 24 hours Thermal Shock Storage Test -2ºC,.5hour 7,.5hour; cycles, hour/cycle High Temperature Operation Test 7ºC, 24 hours () (2) Low Temperature Operation Test -2ºC, 24 hours High Temperature & High Humidity Operation Test 6ºC, 9%RH, 24hours Shock (Non-Operating) 2G, 2ms, half sine wave, time for ± X, ± Y, ± Z. (3) Vibration (Non-Operating).5G, ~ 3 Hz, min/cycle, 3 cycles each X, Y, Z (3) Note! There should be no condensation on the surface of panel during test. Note2! Temperature of panel display surface area should be 7 ºC Max. Note3! During testing vibration and shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. IDM-4 User Manual 32

41 Chapter 9 9Packaging

42 9. Packing Method () Carton Packing suffered no failure in the following reliability tests. Test Item Test Conditions Note Vibration Dropping Test ISTA STANDARD Random, Frequency Range 2 2 Hz Top & Bottom 3 minutes (+Z), min (-Z), Right & Left minutes (X) Back & Forth minutes (Y) Angle, 3 Edge, 6 Face, 6 cm Non Operation Non Operation IDM-4 User Manual 34

43 35 IDM-4 User Manual Chapter 9 Packaging

44 Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. Advantech Co., Ltd. 26