EC BT Wireless Handheld Linear Imager Barcode Scanner. User s Manual
|
|
- Annabella Flowers
- 5 years ago
- Views:
Transcription
1 EC BT-8500 Wireless Handheld Linear Imager Barcode Scanner User s Manual
2 Table of Contents 1. Introduction Safety & Caution FCC Warning General Description Product Description Illustration Installation Unpacking Mounting Setup Bluetooth Communication Pairing Setup SPP Master Mode Setup SPP Slave Mode Setup HID Slave Mode Sleep Mode Batch Mode Out of Range Scanner Mode Configuring Preface Changing Scanner Settings with Programming Codes Programming Flow Chart Programming Menu General Process Set Cradle Interface RS232 mode parameters Keyboard Wedge Mode Parameters Output Characters Code Type UPC/EAN/JAN Parameters Code 39 Parameters Code 128 Parameters Interleaved 2 of 5 Parameters Industrial 2 of 5 Parameters Matrix 2 of 5 Parameters CODABAR Parameters Code 93 Parameters Code 11 Parameters MSI/plessey Code Parameters Telepen Parameters GS1 Databar Parameters GS1 Databar Limited Parameters GS1 Databar Expanded Parameters Miscellaneous Parameters Bar Code ID preambles and postambles Insertion Character deletion Appendices...65 A. Decimal Value Table...65 B ASCII Table...66
3 C Function Key Table...71 D. Decimal Value Table...72 E. Technical Specifications...73 F. Indicator LED Status...74 G. Electrical Characteristics...75 H. Scan Map...76 A. How to communicate with Bluetooth dongle 77
4 1. Introduction Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type area imaging barcode scanner which is designed specifically for retailer, entertainment coupons, medical environment, shipping industry and etc. That adds on more user friendly functions and has replaceable cable that makes it more easily to be operated by the customers. This high performance gun-type scanner provides the customer with the most cost effective solution in the market. It is perfectly suitable and definitely the best choice for you. 1.1 Safety & Caution 1) Please read the following safety statement carefully. 2) Please preserve this user manual for reference sometime. 3) Before cleaning the device, the users must cut off all AC power. Do not use liquid or spray type of detersive to clean the device. Please use dampish cotton cloth to clean the device. 4) The outlet must set nearby the device for connecting power easily. 5) Keep the device dry to avoid short circuit. 6) During installation you must fix the equipment at solid table to avoid damage caused by falling. 7) Before inserting power please ensure the voltage is healthy to the equipment. 8) For safety please tie wire well and don t put anything on the wire. 9) If you don t use this equipment for long time, please cut off the power to avoid damage from surge power. 10) Don t spray any liquid on this scanner because it may cause a fire or short circuit. 1
5 11) Please do not disassemble the equipment. For safety only the qualified serviceman can disassemble the equipment. 12) If there are the following situations please contact with the qualified serviceman to check this equipment. (a) The damage of wire or pin of power supply. (b) Some Liquid infiltrate into the equipment. (c) The equipment has been exposed to wet environment. (d) The equipment can t work well. (e) The equipment has any obvious damage, making the device working abnormally. 13) Don t storage the device at the temperature lower than -20 C (-4 F) or higher than +70 C (158 F) to avoid any damage. 1.2 FCC Warning This equipment complies with the requirements in Part 15 of FCC. Any operation must comply with the conditions below: 1) The equipment will not cause any severe interference. 2) The equipment can avoid any interference from environment. Statement: This product is classified as B class product. In environment this product may cause some interference. In this situation the user may do something to avoid interference. 2
6 2. General Description 2.1 Product Description BT-8500 is a high performance wireless linear imager barcode scanner supporting linear and area imager barcode scanning. This device is very easy to configure by this manual, you can set up by scanning all necessary programming codes one time that meet applications, the settings are directly saved permanently, and all settings can be disabled after scan reset factory default. 2.2 Illustration BT-8500 Series 3
7 3. Installation 3.1 Unpacking 1) Take the device and accessories out of the box. 2) Remove the packing material. 3) Check the standard shipment packing list to make sure you have received all of the items ordered. Wireless Linear Imager Scanner Bluetooth Cradle or Charger (optional) Power Adaptor (if applied) Communication Cable Skip resistant pad Iron panel of cradle and screw Product Compact Disc 4) Visually inspect the device and accessories for any evidence of physical damage. 5) If anything is missing or appears to be damaged, immediately contact your dealer. ATTENTION: Store the packing material and boxes: It should be used whenever the device is transported for servicing. 3.2 Mounting Once you have unpacked all components, you can start installing the device as below steps: BT-8500 Scanner 1) The Scanner must be charged for a minimum of 8 hours before the scanner can be placed in full operation for the first time. 2) The cradle will indicate in red light when the scanner is being charged. 3) Once the battery is fully charged, the green LED of scanner will be on. The green light will be off when the scanner leaving from cradle. When the battery is over charged, the red and green LED will be flashing. 4) If the battery power capacity is too low, the 4
8 scanner will indicate with red LED and beeper warning. BT-8500 Cradle 1) Connect the supplied communication cable at the bottom side of the scanner and you will hear a click when the connection is made. 2) Turn off the host system. 3) Connect the other side of the communication cable to the right connector of your host system. 4) Plug the external power supply into the power jack on the bottom of the cradle. 5) Plug the power supply into the AC outlet. 6) Turn on your host system. 7) To setup Bluetooth communication between the scanner and cradle. (see chapter 4) 5
9 Cable Installation Connect cable and adaptor to Cradle. The other end of cable will be connected with host device. Lock the iron panel of Cradle by screwdriver. Skip resistant pad position 6
10 4. Setup Bluetooth Communication Before the operation, Bluetooth communication must be setup between the scanner and cradle. 4.1 Pairing Each scanner has to be linked or paired to a cradle by scanning the unique Bluetooth MAC address code located on the bottom of cradle. The pairing between scanner and cradle is one to one that is one scanner can be paired to a cradle only. 4.2 Setup SPP Master Mode Please follow the steps to setup the communication between the scanner and cradle. 1) The scanner must scan SPP Master Mode barcode to set the scanner in master mode. 2) Scan the Bluetooth MAC address code located on the bottom of the cradle. 3) When the Bluetooth MAC address code was successfully scanned, scanner will sound 3 beeps with Green led. 4) Wait approximately five seconds for completing the connection process with up-tone. 5) If successful, blue LED of scanner will slow flash and the cradle will be continued on. 7
11 ATTENTION: It is important to know that the scanner will only communicate with the cradle with the unique Bluetooth MAC address. Other scanner cannot pair with that cradle until the original connection is broken. If the cradle pairs with another scanner, the cradle will disconnect with the first scanner and then re-connect with another scanner. 4.3 Setup SPP Slave Mode Please follow the below steps to setup the communication between the scanner and Bluetooth application device. 1) The BT-8500 scanner must scan SPP Slave Mode barcode, to set the BT-8500 scanner in slave mode. 2) When control the Bluetooth device to search the scanner, enter pin code (default 00:00:00) to setup comport. 3) When BT-8500 scanner is successful connected, the scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup. 4.4 Setup HID Slave Mode To setup the communication between the BT-8500 scanner and Bluetooth HID profile application device, follow the steps. 1) The BT-8500 scanner must scan HID Slave Mode barcode to set the BT-8500 scanner in HID slave mode. 2) When control the Bluetooth device to search the scanner, enter pin code to setup pairing. You can scan number barcode on Appendix A, Decimal Value Table number 0~9, to setup. 3) When BT-8500 scanner is successful connected, scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup. 8
12 4.5 Sleep Mode The BT-8500 scanner enters sleep mode to save battery energy, when the BT-8500 scanner is used for 1 minute or 10 minutes. During sleep mode all the functions and connection will be halted. After press the trigger button the scanner will wake up and reconnect the communication with the cradle or Bluetooth device. 4.6 Batch Mode This batch mode is enabled when you have scanned Batch Mode On. The scanned data is stored in the memory of the BT-8500 instead of being transmitted. You can delete the last scanned barcode data by scanning Delete Last Data barcode. This function is disabled when you scan Batch Mode Off. When scan barcode Batch Data Output, the stored scanned data will be immediately transmitted to the host. When scan barcode Batch Data Clear, all stored scanned data will be erased from memory. The capacity of this memory depends on the scanned data. The memory size is approximately 30,000 sets of EAN13 barcode type. 4.7 Out of Range When Out of Range function is enabled, and the scanner is working at out of transmission range, the scanned data will be stored to out-of-range memory. Memory size is approximately 25,000 sets of EAN13 barcode type. The all stored data will be transmitted to device when the link is reconnected, and the all data stored in out-of-range memory will be cleared. 9
13 4.8 Scanner Mode <SPP Master Mode> SPP Slave Mode HID Slave Mode BT Parameter Set Default 10
14 5. Configuring 5.1 Preface How to configure this device: The Barcode Programming Feature gives the possibility to change the scanner settings with programming codes. 5.2 Changing Scanner Settings with Programming Codes The scanner can be configured by scanning all necessary programming codes that meet applications. To change the scanner settings please follow the sequence below: 1. Power up the scanner. 2. Open the scanner programming mode by scanning 3. Start Configuration. 4. Change scanner setting by scanning any of the programming codes that meet applications. 5. Close the scanner programming mode by scanning 6. End Configuration. 7. Save configuration by scanning Save Parameters. For example: To change the baud rate to 38400, scan the following codes successively: Start Configuration Baud Rate End configuration Save Parameters After read a valid programming code, the scanner will give three high beeps and the green LED will light on. By scanning Set All Default, the setting will go back 11
15 to the factory default. 5.3 Programming Flow Chart 12
16 6. Programming Menu Scan Set all Default bar code 6.1 General Process 1 Power up the scanner 2 Scan the Start of Configuration bar code 3 Scan the bar code for the desired feature. You can scan all features before scanning End of Configuration. 4 Scan End of Configuration bar code 5 Scan Save Parameters bar code Abort Configuration Terminate current programming status Recall Replace the current parameters by the parameters saved last time 13
17 6.1.3 Version information Scanner Firmware Version Cradle Firmware Version Scanner MAC Address Cradle MAC Address 6.2 Set Cradle Interface Interface Keyboard Interface RS232 Interface <HID USB Interface> USB Virtual Comport Scanner Mode <SPP Master Mode> SPP Slave Mode 14
18 HID Slave Mode BT Parameter Set Default Batch Mode *** Batch Mode ( *** means Quick Setting Label. The function can be executed directly by scanning barcode instead of doing the general programming process.) <Out of Range Enable> Out of Range Disable Batch Mode ON <Batch Mode OFF> *** Batch Data Read *** Batch Data Clear ***Delete Last Data Sleep Mode Sleep Mode <OFF> Set Scanner to enter Sleep Mode in 1 min Set scanner to enter Sleep Mode in 10 min 15
19 6.3.5 Reading Mode Default setting is shown with <> in Description. Good Read <OFF> Trigger ON/OFF Continuous/Trigger OFF Continuous/Auto Power ON Flash Flash/Auto Power ON Testing Good Read Led Control Good read Led <ON> Good read Led OFF Beeper option <High> 16
20 Medium Low Off Reading Level Bar Equals High <Bar Equals Low> Accuracy / Redundant Scan <Original> - Require 1 good decode for a good scan 1 Redundant Scan - Require 2 consecutive decodes of the same bar code data for a good scan 2 Redundant Scan - Require 3 consecutive decodes of the same bar code data for a good scan 3 Redundant Scan - Require 4 consecutive decodes of the same bar code data for a 17
21 good scan Sensitivity of Continuous Reading This Feature is working under Reading Mode > Continuous modes <Fast> Slow Reverse Output Characters Example: Enable <Disable> 6.3 RS232 mode parameters Baud Rate
22 9600 <19200> Data / Stop Bits The number of data bits transmitted for each character 7 Data Bits < 8 Data Bits > < 1 Stop Bits > 2 Stop Bits Parity A Parity bit is an extra data bit used to help catch data transmission errors. <None> Even Select to set the parity bit either a 1 or 0 to ensure an even number of bits are 1 s 19
23 Odd Select to set the parity bit either a 1 or 0 to ensure an odd number of bits are 1 s Mark Select to set the parity bit always 1. Space Select to set the parity bit always Handshaking RTS/CTS ON Output a Request to Send (RTS) signal and wait for a Clear to Send (CTS) signal before transmitting data RTS/CTS <OFF> ACK/NAK After transmitting data, wait for host to send an ACK or a NAK response. If ACK is received, then complete the data transmission. If NAK is received, re-send the last set of data and wait for ACK/NAK again. ACK/NAK <OFF> XON/XOFF After transmitting data, wait for host to send an XON or a XOFF response. If XON is 20
24 received, then complete the data transmission. If XOFF is received, stop the transmission. XON/XOFF <OFF> 6.4 Keyboard Wedge Mode Parameters Terminal Type <IBM PC/AT,PS/2> - Includes IBM PS/2 and compatible models 50, 55, 60, 80 IBM PC/XT PS/2 25, 30 IBM 5550 IBM 102 Key IBM 122 Key (1) IBM 122 Key (2) NEC 9800 Apple Desktop Bus(ADB) 21
25 6.5.2 Country/Language <US English> UK English Italian Spanish French German Swedish Switzerland Hungarian Japanese Belgium Portuguese 22
26 Denmark Netherlands Turkey Upper/Lower Case <No Change> Enable Lower Case Transmit all data as lower case Enable Upper Case Transmit all data as upper case Interscan Code Delay <No Delay> 5 msec 10 msec 25 msec 50 msec 23
27 100 msec 200 msec 300 msec 6.5 Output Characters Select Terminator <CR+LF> The scanner transmits a carriage return and a line feed after each scan CR Suffix The scanner transmits a carriage return after each scan LF Suffix The scanner transmits a line feed after each scan Space Tab Alt Disable Alt 24
28 STX-ETX RS232 only 6.6 Code Type Barcode Selections If Enable is selected for all bar codes types, then the scanner could read all types of bar code. If Disable is selected for a certain bar code type, then the scanner could not read the particular bar code. The symbol of <> means default settings. All Bar Codes ON UPC-A <ON> UPC-A OFF UPC-E <ON> UPC-E OFF EAN-13 / JAN-13 <ON> EAN-13 / JAN-13 OFF EAN-8 / JAN-8 <ON> 25
29 EAN-8 / JAN-8 OFF CODE 39 <ON> CODE 39 OFF Standard Code 39 <ON> Full ASCII Code 39 ON Code 32 / Italian Pharmacy ON Code32 / Italian Pharmacy <OFF> Code 128 <ON> Code 128 OFF Interleaved 2 of 5 <ON> Interleaved 2 of 5 OFF CODABAR/NW7 <ON> CODABAR/NW7 OFF 26
30 Industrial 2 of 5 ON Industrial 2 of 5 <OFF> Matrix 2 of 5 ON Matrix 2 of 5 <OFF> CODE 93 ON CODE 93 <OFF> CODE 11 ON MSI/PLESSEY ON MSI/PLESSEY <OFF> Telepen ON Telepen <OFF> China Postage ON China Postage <OFF> 27
31 GS1 DataBar ON GS1 DataBar <OFF> GS1 DataBar Expanded ON GS1 DataBar Expanded <OFF> GS1 DataBar Limited ON GS1 DataBar Limited <OFF> 6.7 UPC/EAN/JAN Parameters Reading Type UPC-A=EAN-13 ON Add 0 before UPC-A to make it 13 digits. <UPC-A = EAN-13> <OFF> ISBN Enable ISBN <Disable> ISSN Enable 28
32 ISSN <Disable> Decode with Supplement <Auto discriminate supplement> Supplemental Setup <Not Transmit> 2 Digit Supplemental 5 Digit Supplemental 2 & 5 Digit Supplemental Check Digit Transmission UPC-A Check Digit Transmission <ON> UPC-A Check Digit Transmission OFF UPC-E Check Digit Transmission <ON> UPC-E Check Digit Transmission OFF 29
33 EAN-8 Check Digit Transmission <ON> EAN-8 Check Digit Transmission OFF EAN-13 Check Digit Transmission <ON> EAN-13 Check Digit Transmission OFF ISSN Check Digit Transmission <ON> ISSN Check Digit Transmission OFF 6.8 Code 39 Parameters Type of Code <Standard Code 39> Full ASCII Code Check Digit Transmission <Do not Calculate Check Digit> Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 30
34 6.9.3 Output Start/Stop Character Enable <Disable> Decode Asterisk Enable <Disable> Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths. <Variable> 31
35 Fixed Length 1 st Set 1 st Set Begin Decimal Value See Appendix A 1 st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.9 Code 128 Parameters Check Digit Transmission Do Not Calculate Check Digit 32
36 Calculate Check Digit and Transmit <Calculate Check Digit and Not Transmit> Append FNC2 ON <OFF> Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths <Variable> Fixed Length 1 st Set 1st Set Begin Decimal Value 33 See Appendix A
37 1st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.10 Interleaved 2 of 5 Parameters Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 34
38 Set Up Number of Character <Even> Odd Brazilian Banking Code Enable <Disable> Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths <Variable> 35
39 Fixed Length 1 st Set 1 st Set Begin Decimal Value See Appendix A 1 st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 36
40 6.11 Industrial 2 of 5 Parameters Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit Set Up Code Length To set the fixed length: (2 sets Available) 1. 1Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths <Variable> Fixed Length 1 st Set 1st Set Begin Decimal Value See Appendix A 37
41 1st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.12 Matrix 2 of 5 Parameters Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit 38
42 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths <Variable> Fixed Length 1 st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed length 2 nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete 39
43 Minimum length Minimum Length begin Decimal Value Minimum Length Complete 6.13 CODABAR Parameters Set Up Start/Stop Characters upon Transmission ON <OFF> Transmission Type of Start/Stop A/B/C/D <Start> A/B/C/D <Stop> A Start A Stop B Start 41
44 B Stop C Start C Stop D Start D Stop Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths <Variable> Fixed Length 1 st Set 1 st Set Begin Decimal Value 42 See Appendix A
45 1 st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.14 Code 93 Parameters Check Digit Transmission Calculate Check Digit Disable <Calculate Check 2 Digit and Not Transmit> 43
46 Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths. <Variable> Fixed Length 1st Set 1 st Set Begin Decimal Value See Appendix A 1 st Set Complete Fixed length 2 nd Set 2 nd Set Begin Decimal Value See Appendix A 2nd Set Complete 44
47 Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.15 Code 11 Parameters Check Digit Transmission <Do Not Calculate Check Digit> Calculate Check 1 Digit and Transmit Calculate Check 1 Digit and Not Transmit Calculate Check 2 Digit and Transmit Calculate Check 2 Digit and Not Transmit Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 45
48 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths. <Variable> Fixed Length 1st Set 1st Set Begin Decimal Value See Appendix A 1st Set Complete Fixed length 2 nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 46
49 6.16 MSI/plessey Code Parameters Check digit transmission <Do Not Calculate Check Digit> Calculate Check Digit and Transmit Calculate Check Digit and Not Transmit Set Up Code Length To set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths. <Variable> Fixed Length 1 st Set 1 st Set Begin Decimal Value See Appendix A 47
50 1 st Set Complete 48
51 Fixed length 2 nd Set 2nd Set Begin Decimal Value See Appendix A 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.17 Telepen Parameters Type of Code Telepen ASCII <ON> Telepen Numeric Check Digit Transmission Do Not Calculate Check Digit Calculate Check Digit and Transmit 49
52 <Calculate Check Digit and Not Transmit> Set Up Code Length o set the fixed length: (2 sets Available) 1. Scan the Begin programming code of the desired set 2. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the length to be read. 3. Scan the Complete programming code of the desired set. Repeat the steps 1 3 to set additional lengths. <Variable> Fixed Length 1st Set 1 st Set Begin Decimal Value See Appendix A 1 st Set Complete Fixed length 2nd Set 2 nd Set Begin Decimal Value See Appendix A 50
53 2nd Set Complete Minimum length Minimum Length begin Decimal Value See Appendix A Minimum Length Complete 6.18 GS1 Databar Parameters Check Digit Transmission <Calculate Check Digit and Transmit> Calculate Check Digit and Not Transmit Application ID <Transmit Application ID> Add 01 before GS1 Databar. Don t Transmit Application ID Symbology ID Transmit Symbology ID Add ]e0 before GS1 Databar. 51
54 <Don t Transmit Symbology ID> 6.19 GS1 Databar Limited Parameters Check Digit Transmission <Calculate Check Digit and Transmit> Calculate Check Digit and Not Transmit Application ID <Transmit Application ID> Add 01 before GS1 Databar Limited. Don t Transmit Application ID Symbology ID Transmit Symbology ID Add ]e0 before GS1 Databar Limited. <Don t Transmit Symbology ID> 52
55 6.20 GS1 Databar Expanded Parameters Symbology ID Transmit Symbology ID Add ]e0 before GS1 Databar Expanded. <Don t Transmit Symbology ID> 53
56 7. Miscellaneous Parameters 7.1 Bar Code ID Default Barcode ID With this function on, a leading character will be added to the output string while scanning code; user may refer to the following table to know what kind of barcode is being scanned. Code Type ID Code Type ID UPC-A A UPC-E B EAN-8 C EAN-13 D Code 39 E Code 128 F Interleaved 2 of 5 G Industrial 2 of 5 H Matrix 2 of 5 I Codabar J Code 93 K Code 11 L China Postage M MSI/Plessey N Telepen T GS1 DataBar U GS1 DataBar V GS1 DataBar W Lim. Exp. Bar Code ID ON Bar Code ID <OFF> 54
57 Default Return from User Define to Default User Define Code ID To set the code ID 1. Scan the symbologies programming code. 2. Go to the ASCII Tables in Appendix B, Scan programming codes that represents the desired ID. Note: User defines code ID will override default value. Program will not check the conflict. It is poss ble to have more than two symbologies which have the same code ID. UPC-A UPC-E EAN-13/JAN-13 EAN-8/JAN-8 CODE 39 CODE 128 CODABAR 55
58 Interleaved 2 of 5 Industrial 2 of 5 Matrix 2 of 5 CODE 93 CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar GS1 DataBar Expanded GS1 DataBar Limited 7.2 preambles and postambles Insertion Setup Insertion To set the insertion of the output characters; 1. Scan the programming code of the desired set. 56
59 2. Scan the programming code of the desired symbology 3. Go to the Decimal Value in Appendix A, scan programming codes that represents the desired position to be inserted (1= the first digit, 99 the last digit). 4. Scan the Complete programming code of Character Position to be inserted. 5. Go to the ASCII Tables in Appendix C, Scan programming codes that represents the desired characters to be inserted. 6. Scan the Complete programming code of Characters to be inserted. Repeat the steps 1 6 to set additional insertion. Example: Insert $ as Preamble for Code UPC-A. Start configuration 1 st Set Code UPC-A 1st digit Complete $ 57
60 Complete End of Configuration bar code Save Parameters bar code Insertion set number 1 st Set 2 nd Set 3 rd Set 4 th Set 5 th Set 6 th Set Symbologies Selection UPC-A UPC-E EAN-13/JAN-13 58
61 EAN-8/JAN-8 CODE 39 CODE 128 Codabar/NW7 Interleaved 2 of 5 Industrial 2 of 5 Matrix 2 of 5 CODE 93 CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar 59
62 GS1 DataBar Expanded GS1 DataBar limited All Codes None Character Position to be inserted Decimal Value See Appendix A Complete Characters to be Inserted ASCII Table See Appendix B and C Complete 7.3 Character deletion To setup the deletion of output characters: 1. Scan the programming code of the desired set. 2. Scan the programming code of the desired symbology. 60
63 3. Go to the decimal Value tables in Appendix A, scan programming codes that represents the desired position to be deleted. 4. Scan the Complete programming code of Character Position to be Deleted. 5. Go to the Decimal Value Tables in Appendix A, scan programming codes that represents the number of characters to be deleted. 6. Scan the Complete programming code of Number of Characters to be deleted. Repeat the steps 1 6 to set additional deletion. Example: Delete first 3 codes for Code EAN-13. Start Configuration 1 st Set Code EAN-13 1st digit delete from the 1 st digit Complete 3 delete 3 characters 61
64 Complete End of Configuration bar code Save Parameters bar code 62
65 7.3.1 Deletion Set Number 1 st Set 2 nd Set 3 rd Set 4 th Set 5 th Set 6 th Set Code Type to be Delete UPC-A UPC-E EAN-13/JAN-13 EAN-8/JAN-8 CODE 39 CODE
66 CODABAR/NW7 Interleaved 2 of 5 Industrial 2 of 5 Matrix 2 of 5 CODE 93 CODE 11 China Postage MSI/PLESSEY Telepen GS1 DataBar GS1 DataBar Expanded GS1 DataBar Limited All Codes 64
67 None Character Position to be Delete Decimal Value See Appendix A Complete Number of Characters to be Deleted Decimal Value See Appendix A Complete 7.4 Appendices A. Decimal Value Table 65
68 B ASCII Table NULL RS ETX STX ACK ENQ HT BS FF VT SI SO DC2 DC1 NAK DC4 CAN ETB ESC SUB GS SYN SOH EM 66
69 BEL US LF SPACE CR DLE! DC3 # % 0 $ 1 & 2 ( 3 ' 4 ) * 7 67
70 , 8 Comma. 9 period - B minus / C ; D : E < F Less than > G Greater than = H? I Letter J A K L T 68
71 M U N V O W Letter O P X Q Y R Z S [ ] \ ^ _ ` Underscore a h b i c j 69
72 d k e l f m g n o u p v q w r x s y t z { Vertical slash } ~ DEL 70
73 C Function Key Table F1 F7 F2 F8 F3 F9 F4 F10 F5 F11 F6 F12 Insert Delete Home End Page Page Down Up Up Left Down 71
74 D. Decimal Value Table Enter 72
75 E. Technical Specifications a) Physical Characteristics Weight BT Scanner Cradle Accessory KBW Cable RS232 Cable USB Cable AC Adaptor Material Connector Cable Length Dimension Scanner Cradle Approx. 210g Approx. 105g Approx. 75g Approx. 123g Approx.67g Approx.125g ABS Plastic RJ 45C 10Pins 5Ft. (150mm) 193x90x72mm 206x101x49mm b) Performance Scanner Characteristics Light Source Visible Red Light 650nm ± 10nm Scan Rate Smart detect up to maximum 500 scans/second ±10% Sensor Linear CCD Sensor Processor Type ARM Cortex - M3, 32- bit Operating Freq. 8 MHz Depth of Field Up to 500mm@20mil, PCS90%, Code39 Print Contrast 45% Ratio Resolution 4mil(0.1mm)@PCS90% Scan Angle Forward & Backward(Pitch) ±10 ~65 (±5 ) Left & Right(Skew) ±60 (±5 ) Interface KBW, RS- 232, USB (HID SG- 300BT Cradle KBW), Virtual Comport Ambient Light 10,000 Lux Max. 73
76 c) Bluetooth Characteristics Bluetooth Module Bluetooth V2.0 Standard Frequency Band 2.402GHz ~ 2.480GHz Modulation Method GFSK for 1Mbps RF Output Power Under 20dBm (Class 1) Bluetooth Distance Range Class1 ; 100M line of sight Data Storage on BT Disconnect 30,000 scans for EAN13 F. Indicator LED Status a) Cradle Light Signal Status Green Red Blue 1 blink continuous on off good read and transmitted power on power off 2 blink BT disconnect continuous on BT connected b) Scanner Light Signal Status Green good read and transmitted 1 blink and 1 beep good read and save on memory (BT disconnect) continue on red blink 2 times and 2 long beeps battery charged full memory full Red Blue down- tone red blink 1 time and beep per 20 seconds red blink 4 times and bi- bi- bi- bi per 10 seconds 2 short blink and 2 short beeps continue on blue light 2 second and Down tone blue blink 2 times per 74 enter sleep mode battery low warning battery very low power alarm good read but transmit fail in charging BT disconnect on connecting
77 second blue blink per second BT connected Red Blue blue light 2 second and up- tone 1 blink at the same time and 2 beeps BT connecting succeed setting ok G. Electrical Characteristics a) Scanner Power Battery Li- ion 3.7V / 1100 ma. Charge Time 3.5 hours Reads per Charge 10,000 Times Power Consumption PowerOn 190mA Standby 50mA Operation 150mA Sleep 6mA Cradle Input Voltage 5 2 A / Input AC V Power Consumption PowerOn 95mA StandBy 55mA Operation 70mA b) Environmental Operating Temp 0 C to 50 C Storage Temp C to 70 C Relative Humidity 0 to 95% non- condensing Ambient Light 100,000 Lux (direct sunlight) c) Regulatory of Compliance FCC, CE, RoHs 75
78 H. Scan Map How to communicate with Smartphone 1) Make the device discoverable. (Page 8 4.3,4.4) 2) See the documentation that came with the device. 3) Go to Settings > Bluetooth and turn Bluetooth on. 4) Select the barcode scanner device and, if prompted, enter the passkey or PIN. See the instructions (page 69) about the passkey or PIN that came with the device. 76
79 A. How to communicate with Bluetooth dongle 1) Switch the Scanner SPP HID mode or SPP Slave mode. (Page 8 4.3,4.4) 2) Active the BT dongles software to search the Bluetooth device. 3) Select the barcode scanner device to pairing; When pairing, it will request key in the (PINCODE), Please refer to page 69 for Help. 4) After pairing completed, connection can be carried out. 5) Scanner SPP Slave mode, after a successful connection, BT Dongle software will provided virtual comport, if need to check the data output, Please activate the Hyper Terminal program, and setup the RS232 parameter(com port number and baud rate) then you can see the data output. 6) Scanner SPP HID mode after the connection successful, only need to activate the general editing software (For example: notepad, word. etc) then you can see the data output. ATTENTION: Compat ble to Bluetooth V2.1+EDR, V2.0+EDR, V1.2,V1.1 or backward version Class1 and Class 2 dongles, The transmission distance is depends on the environmental conditions and the dongle as a Class 1 or Class 2 may be. Due to Champtek s continuing product improvement programs, specifications and features are subject to change without notice. 77
VEGA Linear Imager V-1010/V-1010BT Handheld Bar code Scanner
U s e r s M a n u a l VEGA Linear Imager V-1010/V-1010BT Handheld Bar code Scanner EMEA SCANTECH-ID BV Nijverheidsweg Noord 60-34 3812 PM Amersfoort The Netherlands Tel:+31-33-4698400 Fax:+31-33-4650615
More informationVersaScan III. Barcode Scanner Quick Start Manual. ID TECH Walker Street Cypress, CA (714)
VersaScan III TM Barcode Scanner Quick Start Manual ID TECH 10721 Walker Street Cypress, CA 90630 (714) 761-6368 www.idtechproducts.com 80105505-001 RevA FCC WARNING STATEMENT This equipment has been tested
More informationIG820 Series Area Image Barcode Scanner SPECIFICATION. Model No. : IG820 Gun-type Area Image Barcode Scanner
IG820 Series Area Image Barcode Scanner 01 SPECIFICATION Customer : Customer s Model No. : Model No. : IG820 Gun-type Area Image Barcode Scanner Date : Sample Serial No. : Spec. ersion & Revision Date:
More informationLeitor Youjie ZL2200.
Leitor Youjie ZL2200 Youjie ZL2200 é um leitor laser de feixe único de baixo custo e com ótimo desempenho. Um scanner de código de barras nível de entrada que visa a melhor relação custo benefício, sendo
More informationNT-9600 Wireless Barcode Scanner. Introduction
Guangzhou Netum Electronic Technology Co., Ltd TEL: +86 20 82679969*816 FAX: +86 20 82684887 E-mail: scottchiu@gzxlscan.com Address: Unit137, the Pacific Industry Area, Xintang Town, Zengcheng District,
More informationLZ400RF Laser User Manual B78 Base User Manual and Setup Menu
LZ400RF Laser User Manual B78 Base User Manual and Setup Menu Worth Data Inc. December 2007 The LZ400-RF and the B78 Base Station have been tested and found to comply with the limits for a Class A digital
More informationAEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE
AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE Thank you for purchasing a TSI AeroTrak Model 9110 Portable Airborne Particle Counter (particle counter). This guide will help you
More informationAllen-Bradley D. User Manual. Hand-Held Decoded Bar Code Scanners. (Cat. No HDG-4)
Allen-Bradley Hand-Held Decoded Bar Code Scanners User Manual (Cat. No. 2755-HDG-4) Allen-Bradley D Important User Information The illustrations, charts, sample programs and layout examples shown in this
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in
More informationCommander 384. w w w. p r o l i g h t. c o. u k U S E R M A N U A L
Commander 384 w w w. p r o l i g h t. c o. u k U S E R M A N U A L 1, Before you begin 1.1: Safety warnings...2 3 1.2: What is included...4 1.3: Unpacking instructions...4 2, Introduction 2.1: Features...4
More informationKramer Electronics, Ltd. USER MANUAL. Model: 900xl. Power Amplifier
Kramer Electronics, Ltd. USER MANUAL Model: 900xl Power Amplifier Introduction Contents 1 Introduction 1 2 Getting Started 1 2.1 Recycling Kramer Products 1 3 Overview 2 4 Your 900xl Power Amplifier 3
More informationProduct model and standard
Preface Thank you for purchasing the Ikan Blitz 400 HD Wireless Video System. This system features uncompressed high definition video with zero delay. Before using the product, please read this user s
More informationUser Manual. HDBaseT Wallplate Transmitter over Cat6/6A. Front View Panduit Dr, Tinley Park, IL (708)
User Manual HDBaseT Wallplate Transmitter over Cat6/6A Front View 18900 Panduit Dr, Tinley Park, IL 60487 (708) 532-1800 Back View TABLE OF CONTENTS Introduction 2 Features 3 Package Contents 3 Technical
More information-TECH DIGITAL. Explore The High DefinitionWorld. Website: Hot Line: [US] USER MANUAL
-TECH DIGITAL Explore The High DefinitionWorld Website: www.jtechdigital.com Hot Line: 1-888-610-2818[US] USER MANUAL J-Tech Digital ProAV H.264 Encoder/Decoder Many to Many HDMI Extender RoHS 1 Operating
More informationPLL1920M LED LCD Monitor
PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6
More informationTABLE OF CONTENTS. Instructions:
TABLE OF CONTENTS Instructions: 1 Overview 1 2 Main technical parameters 1 3 Display and keyboard 2 3.1 Display Window 2 3.2 Indicator 4 4. Operation 4 4.1 Power 4 4.2 Zero 4 Modified 4 4.3 Modified 4
More information2nd Edition. Quick Start Guide. getawair.com
2nd Edition Quick Start Guide getawair.com Stay Healthy Awair tracks toxins and chemicals in your air and gives you personalized recommendations to help you stay safe and healthy. Sensors Fine Dust (PM2.5)
More information17 19 PROFESSIONAL LCD COLOUR MONITOR ART
17 19 PROFESSIONAL LCD COLOUR MONITOR ART. 41657-41659 Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelit.eu e-mail:export.department@comelit.it WARNING: TO REDUCE THE RISK OF FIRE
More informationUser Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor
Touch Display LCD Monitor User Manual Installation Guide 15 Resistive Touch LCD Monitor MODEL: KK1500-TR i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com User
More informationIRISPen Air 7. Quick User Guide. (ios - ipad)
IRISPen Air 7 Quick User Guide (ios - ipad) This Quick User Guide helps you get started with the IRISPen TM Air 7. Please read this guide before operating this scanner and its software. All information
More informationDDW36C Advanced Wireless Gateway - Safety and Installation Product Insert. Federal Communications Commission (FCC) Interference Statement
DDW36C Advanced Wireless Gateway - Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits
More informationDell Wyse 5030 PCoIP Zero Client
Dell Wyse 5030 PCoIP Zero Client User Guide Regulatory Model: PxN Regulatory Type: PxN001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your
More informationChapter 3 Digital Data
Chapter 3 Digital Data So far, chapters 1 and 2 have dealt with audio and video signals, respectively. Both of these have dealt with analog waveforms. In this chapter, we will discuss digital signals in
More informationUser Manual MODEL: KKF1500-PCAP. True FLAT P-CAP LCD Monitor. Installation Guide. 15 True FLAT P-CAP Touch LCD Monitor
True FLAT P-CAP LCD Monitor User Manual Installation Guide 15 True FLAT P-CAP Touch LCD Monitor MODEL: KKF1500-PCAP i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com
More informationVNS2200 Amplifier & Controller Installation Guide
VNS2200 Amplifier & Controller Installation Guide VNS2200 Amplifier & Controller Installation 1. Determine the installation location for the VNS2200 device. Consider the following when determining the
More informationUser manual. Long Range Wireless HDMI/SDI HD Video Transmission Suite
User manual Long Range Wireless HDMI/SDI HD Video Transmission Suite Preface Thanks for purchasing our Long Range Wireless HDMI/SDI HD Video Transmission Suite. Before using this product, read this user
More informationDCP100 Digital Control Programmer Specifications
DCP100 Digital Control Programmer Specifications EN01-6028 October 1996 Overview The DCP100 is a microprocessor based 1 /4 DIN programmer/controller for process variable versus time control of temperature,
More informationMONOPRICE. Blackbird 4K HDBaseT Extender Kit. User's Manual P/N 21792
MONOPRICE Blackbird 4K HDBaseT Extender Kit P/N 21792 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings
More informationPLL2210MW LED Monitor
PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationReflecta Super 8 Scanner. User Manual
Reflecta Super 8 Scanner User Manual 1 FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part
More informationDisplays Open Frame Monitor Model Number: AND-TFT-150Bxx
Displays 15.0 Open Frame Monitor Model Number: AND-TFT-150Bxx The AND-TFT-150Bxx 15.0 Open Frame Monitor series are rugged, high performance Industrial LCD Monitors, designed for commercial and industrial
More informationRemote Control. degraded, causing unreliable operation. The recommended effective distance for remote operation is about 16 feet (5 meters).
Media Streaming Sound Bar RTS736W User Manual Remote Control using the remote control Point the remote control at the REMOTE SENSOR located on the unit (see Front Panel illustration for precise location).
More informationBY-HPE11KTA. Operating Instructions. Coaxial - LAN Converter with PoE function. Indoor Use Only. Model No. Attached Installation Guide
Operating Instructions Coaxial - LAN Converter with PoE function Model No. Indoor Use Only BY-HPE11KTA Attached Installation Guide Before attempting to connect or operate this product, please read these
More information6.4 Chassis Monitor Model Number: LCM0642xx. SPEC No.: SAS Version: 0.0 Issue Date: April 16, Introduction:
6.4 Chassis Monitor Model Number: LCM0642xx This product is RoHS compliant SPEC No.: SAS-0908003 Version: 0.0 Issue Date: April 16, 2010 1. Introduction: 1.1 About the Product The LCM0642xx 6.4 Chassis
More informationTFT-LCD TV USER MANUAL W102T READ CAREFULLY BEFORE OPERATION W102T
TFT-LCD TV W102T USER MANUAL READ CAREFULLY BEFORE OPERATION W102T IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. This symbol indicates dangerous voltage inside the product
More informationStart Up or Shut Down Hunting Function. Using the Receiver. If there is a short circuit in the cable, it will display as follows:
If there is a short circuit in the cable, it will display as follows: Push key (No) to exit calibration function. Push key (Yes) to repeat measurement process. 11 Note: The calibration will recover the
More informationFLAT DISPLAY TECHNOLOGY
15.0 Open Frame Monitor Model Number: LOF1506xx This product is RoHS compliant SPEC No.: SAS-1008002 Version: 0.0 Issue Date: September 6, 2010 1. Introduction: 1.1 About the Product The LOF1506xx 15.0
More informationBe sure to run the vehicle engine while using this unit to avoid battery exhaustion.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNE; Please Read all of these instructions regarding
More informationOperator s Manual. Ultegra. Health Scale. Fairbanks Scales by Fairbanks Scales Inc. All rights reserved. Revision 5 06/07
Operator s Manual Ultegra Health Scale Fairbanks Scales 2007 by Fairbanks Scales Inc. All rights reserved 50735 Revision 5 06/07 Amendment Record Ultegra Health Scale 50735 Manufactured by Fairbanks Scales
More informationQuick Operation Guide of LTN7700/7600 Series NVR
Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable
More information28 4K LED monitor. User Manual M284K
28 4K LED monitor User Manual M284K CONTENTS Safety Information... 2 What s included..... 4 Getting Started....... 8 Troubleshooting.... 14 Specification.... 15 2 of 15 SAFETY INFORMATION Read these instructions
More informationKramer Electronics, Ltd. USER MANUAL. Model: FC Analog Video to SDI Converter
Kramer Electronics, Ltd. USER MANUAL Model: FC-7501 Analog Video to SDI Converter Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your Analog Video to SDI Converter 3 5 Using Your
More informationUSER MANUAL. 27 Full HD Widescreen LED Monitor L27ADS
USER MANUAL 27 Full HD Widescreen LED Monitor L27ADS TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety
More informationE3/DS3 Fibre Extender
User Manual E3/DS3 Fibre Extender Black Box Network Services 464 Basingstoke Road, Reading, Berkshire, RG2 0BG Tech: 0118 965 6000 www.blackbox.co.uk CONTENTS 1 Introduction 1 1.1 About the products 1
More informationOPERATING INSTRUCTIONS TOM-0431IP
OPERATING INSTRUCTIONS TOM-0431IP Table of Contents FCC Information -------------------------------------------------------------------- 2 Safety and Environmental Precautions ------------------------------------------------
More informationDISTRIBUTION AMPLIFIER
MANUAL PART NUMBER: 400-0045-005 DA1907SX 1-IN, 2-OUT VGA/SVGA/XGA/UXGA DISTRIBUTION AMPLIFIER USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL...2 GUIDELINES FOR RACK-MOUNTING...2
More informationPL2410W LCD Monitor USER'S GUIDE.
PL2410W LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationNoise Detector ND-1 Operating Manual
Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-201YC. 2x1 s-video Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-201YC 2x1 s-video Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VS-201YC 2x1 s-video Switcher 4 5
More informationIt will cause malfunction if the monitor is operating with unspecified power supply
User Manual / Installation Guide Model No. PTM-1525R/RT Warning! It will cause malfunction if the monitor is operating with unspecified power supply unit or incorrect power voltage. Do not exposure this
More informationP XGA TFT Monitor. User s Manual
P6151 15 XGA TFT Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements
More informationUSER S Manual NGLT104WPD NGLT150WPD LCD TV / Monitor (IP67 Grade)
USER S Manual NGLT104WPD NGLT150WPD LCD TV / Monitor (IP67 Grade) This Manual is revisable without further notice Contents CONTENTS ------------------------------------------------------------------- 1
More informationLong Range Wireless HDMI/SDI HD Video Transmission Suite LINK-MI LM-SWHD01. User manual
Long Range Wireless HDMI/SDI HD Video Transmission Suite LINK-MI LM-SWHD01 User manual Preface... 1 1. Cautions... 2 2. About... 3 3. Installation... 4 4. Operation instruction... 5 5. Maintenance... 6
More informationJD725A Cable and Antenna Analyzer - Dual Port
COMMUNICATIONS TEST & MEASUREMENT SOLUTIONS JD725A Cable and Antenna Analyzer - Dual Port Key Features Portable and lightweight handheld instrument Built-in wireless frequency bands as well as the most
More informationOperating Manual. Comparator V7 / V8. Hardware and Software. Document Version A. Doc. No.: OM_PCE_VGL_ V7_ V8_v1.023_EN_A_ext.doc
Operating Manual Comparator V7 / V8 Hardware and Software Document Version A Doc. No.: OM_PCE_VGL_ V7_ V8_v1.023_EN_A_ext.doc Starting at Software Version 1.023 Date 05/02/2015 File Name: OM_PCE_VGL_ V7_
More informationKramer Electronics, Ltd. USER MANUAL. Models: VS-162AV, 16x16 Audio-Video Matrix Switcher VS-162AVRCA, 16x16 Audio-Video Matrix Switcher
Kramer Electronics, Ltd. USER MANUAL Models: VS-162AV, 16x16 Audio-Video Matrix Switcher VS-162AVRCA, 16x16 Audio-Video Matrix Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview
More informationUSER MANUAL. 22" Class Slim HD Widescreen Monitor L215DS
USER MANUAL 22" Class Slim HD Widescreen Monitor L215DS TABLE OF CONTENTS 1 Getting Started Package Includes Installation 2 Control Panel / Back Panel Control Panel Back Panel 3 On Screen Display 4 Technical
More informationMounting Dimensions / Viewing 2 Mounting Options 3. Wiring Configuration 4. Quick Set up Procedure 5. Changing Intensity 6.
Contents Section Mounting Dimensions / Viewing 2 Mounting Options 3 Section 2 Wiring Configuration 4 Section 3 Quick Set up Procedure 5 Section 4 Changing Intensity 6 Section 5 Option Summary 7 Section
More informationElectrical connection
Color sensors Dimensioned drawing en 02-2013/01 50121262 068-14515 12mm 32mm 10-30 V DC 500 Hz Scanner for color detection Simultaneous selection of up to 3 colors Detection independent of distance Teach-in
More informationSpectra Batten (Order code: LEDJ95)
www.prolight.co.uk Spectra Batten (Order code: LEDJ95) Safety WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this equipment away from rain,
More informationTABLE OF CONTENTS Important Safety Instructions Package Content Setting Up the Display Trouble shooting Specifications Product Dimensions
TABLE OF CONTENTS Important Safety Instructions...1 1.1 Safety precautions and maintenance....1 1.2 Use.......4 1.3 Installation Notes.......7 Package Content...9 2.1 Unpacking...9 2.2 Accessories......10
More informationWinmate Communication INC.
20.1 Military Grade Display Model: R20L100-RKA2ML User s Manual Winmate Communication INC. May, 2011 1 IMPORTANT SAFETY INSTRUCTIONS Please read these instructions carefully before using the product and
More informationAES-404 Digital Audio Switcher/DA/Digital to Analog Converter
Broadcast Devices, Inc. AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web: www.broadcast-devices.com
More informationRA-RS232, RB-RS232. Setup and Installation Guide Addendum For RadioRA RS232 Interface
RA-RS232, RB-RS232 Setup and Installation Guide Addendum For RadioRA RS232 Interface A Comprehensive Step-by-Step Guide for Programming and Operating the Lutron RadioRA RS232 Interface Note: Please leave
More informationInstallation Guide SY-MS51. and SY-MS51-AP. Scaling Presentation Switcher
Installation Guide SY-MS51 and SY-MS51-AP Scaling Presentation Switcher 3 HDMI, 2 VGA (RGBHV, YPbPr or Composite Video) inputs Simultaneous HDMI & HDBT outputs SY Electronics Ltd, 7 Worrall Street, Salford,
More informationWeighing Scale. 10key&12key User manual
Weighing Scale 10&12 User manual EXCELL PRECISION CO., LTD. 2014. All rights reserved worldwide. The information contained herein is the property of EXCELL PRECISION CO., LTD. and is supplied without liability
More informationSM-10 SAT Level Meter User s Manual
SM-10 SAT Level Meter User s Manual DAGATRONICS CORPORATION 263-1 DUCKIDONG, ILSAN, KOYANG, KYUNGKIDO, KOREA TEL: +82-31-916-8005 FAX: +82-31-916-8080 Email: dagatron@dagatron.com Website: www.dagatron.com
More information4 x 4 VGA Matrix Switch
Hall Research Technologies, Inc. 4 x 4 VGA Matrix Switch Model VSM-404 User s Manual With Serial Keypad CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. 800-959-6439 FREE technical support, Call
More informationSmart Control SC16 3-Channel for matrix
Operating Manual Smart Control SC16 3-Channel for matrix Dear Customer, Thank you for choosing a WALTRON daytime lighting controller. Your daytime lighting controller is a high-quality product that was
More informationLAN Network Tester. Operating Manual. Part No TRIAX - your ultimate connection
LAN Network Tester Part No. 157011 Operating Manual TRIAX - your ultimate connection Safety and Disposal The LAN Network Tester operates off 6V DC only. Only use the internal, battery powered, 6V power
More informationIntroduction...2. Features...2 Safety Precautions...2. Installation...4
PE1900 Contents Introduction...2 Features...2 Safety Precautions...2 Installation...4 Unpacking the Display...4 Locations and Functions of Controls...4 Connections...5 Using Your Display...7 Turning the
More informationUSER MANUAL. KW-11T Wireless High Definition Transmitter. KW-11R Wireless High Definition Receiver MODELS: P/N: Rev 9
KRAMER ELECTRONICS LTD. USER MANUAL MODELS: KW-11T Wireless High Definition Transmitter KW-11R Wireless High Definition Receiver P/N: 2900-300194 Rev 9 Contents 1 Introduction 1 2 Getting Started 2 2.1
More informationSingle cable multiswich programmer PC102W
Single cable multiswich programmer PC102W 1. Product description The PC102W - single cable multiswich programmer (in the text - programmer) is useful instrument while configuring and troubleshooting SAT
More information192 Channel DMX Controller
DM-X 92 Channel DMX Controller USER MANUAL 54. 9UK Vers ion. D M X 5 2 C O N T R O L L E R S E R I E S Content. Before you begin. What is included.......2 Unpacking instructions....3 Safety instructions...
More informationPower Injector 1520 Series
Power Injector 1520 Series Technical Specifications Input voltage 100 to 240 VAC Output voltage 56.0 VDC Voltage range tolerance 54 VDC to 57 VDC Maximum current 1.43 A No load current 15 ma 56VDC@0.71A
More informationSabre 1551C Decoding Laser Scanner
Quick Reference Guide P/N 068442-002 Sabre 1551C Decoding Laser Scanner 1233* FranklinGothic Helv Condensed Intermec Technologies Corporation 6001 36th Avenue West P.O. Box 4280 Everett, WA 98203-9280
More informationSPX-5600 Series. Operations Manual. Suprex Reader Extender - RF Wireless Interface SPX-5600MAN. Page 1 of 20
SPX-5600 Series Operations Manual Suprex Reader Extender - RF Wireless Interface SPX-5600MAN Page 1 of 20 SPX-5600 Series: Cypress Suprex SPX-5600 Series This manual covers the operation and setup of the
More informationInstallation Guide. HDMI 4x1 Switcher
Installation Guide HDMI 4x1 Switcher SY Electronics Ltd, Unit 7, Worrall Street, Salford, Greater Manchester, M5 4TH, United Kingdom Tel: +44 (0) 161 868 3450 Fax: +44 (0) 161 868 3459 The SY-HD-S41 is
More informationAES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter
Broadcast Devices, Inc. AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web:
More informationINSTALLATION MANUAL FT-FOTR-1VDE-ST-S
INSTALLATION MANUAL FT-FOTR-1VDE-ST-S 1-Channel Digital Duplex Baseband Video Transmitter and Receiver With Reverse Data Transmission & Ethernet Transmission v1.0 4/5/11 1 PACKAGE CONTENTS This package
More informationTRANSCENSION 6-CHANNEL DMX DIMMER PACK (order code: BOTE40) USER MANUAL
www.prolight.co.uk TRANSCENSION 6-CHANNEL PACK (order code: BOTE40) USER MANUAL SAFETY WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this
More informationPart names (continued) Remote control
Introduction Part names (continued) Remote control (1) STANDBY ( 25) (1) (2) ON ( 25) (3) (3) ID - 1 / 2 / 3 / 4 s ( 18) (4) (4) COMPUTER 1 ( 27) (7) (5) COMPUTER 2 * (8) (6) COMPUTER 3 * (10) (13) (7)
More informationO P E R A T I O N M A N U A L. RF-Reader. Stand-alone-Reader Leser 2plus with RS-232 interface
O P E R A T I O N M A N U A L Version 01/05 RF-Reader Stand-alone-Reader Leser 2plus with RS-232 interface Important! Read by all means! To maintain the perfect shipping conditions and to ensure safe operation
More information28 & 32 & 40 & 55 & 65 & 84-INCH TFT-LCD 4K MONITOR
28 & 32 & 40 & 55 & 65 & 84-INCH TFT-LCD 4K MONITOR INSTRUCTION MANUAL Please read this manual thoroughly before use, and keep it handy for future reference. TABLE OF CONTENTS 1, General information...
More informationFor warranty service, please contact Microframe at: A technician will gladly assist you.
Your Microframe System is warranted against failure due to defects in workmanship or material for a period of one (1) year from the date of purchase. Microframe Corporation will repair or replace any defective
More informationLong Range Wireless HDMI/SDI HD Video Transmission Suite LINK-MI LM-SWHD01. User manual
Long Range Wireless HDMI/SDI HD Video Transmission Suite LINK-MI LM-SWHD01 User manual Preface... 1 1. Cautions... 2 2. About... 3 3. Installation... 4 4. Operation instruction... 5 5. Maintenance... 6
More informationC O B A R 18R U s e r G u i d e P a g e 1. User Guide COBRA 18R. Wireless Firing System.
C O B A R 18R U s e r G u i d e P a g e 1 User Guide COBRA 18R Wireless Firing System C O B A R 18R U s e r G u i d e P a g e 2 TABLE OF CONTENTS 1. SYSTEM INTRO... 3 2. POWER ON... 4 3. REMOTE / FIRING
More informationUSER MANUAL. 27 Full HD Widescreen LED Monitor L270E
USER MANUAL 27 Full HD Widescreen LED Monitor L270E TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety
More information4K LED MONITOR 430LED4K & 550LED4K INSTRUCTION MANUAL. Please read this manual thoroughly before use, and keep it handy for future reference.
4K LED MONITOR 430LED4K & 550LED4K INSTRUCTION MANUAL Please read this manual thoroughly before use, and keep it handy for future reference. CONTENTS 1. GENERAL INFORMATION...3 2. 3. 1.1. 1.2. 1.3. 2.1.
More informationInstallation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters
Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Written By: Colin Langridge Issue: Draft Date: 03 rd July 2008 1 Date: 29 th July 2008 2 Date: 20 th August 2008 3 Date: 02 nd
More informationDual Antenna Wireless Multi-Channel Expandable HDMI Extender Installation Guide
Dual Antenna Wireless Multi-Channel Expandable HDMI Extender Installation Guide 04-1125A Introduction The Dual Antenna Wireless Multi-Channel Expandable HDMI Extender wirelessly transmits HDMI signals
More informationUSER MANUAL. 28" 4K Ultra HD Monitor L28TN4K
USER MANUAL 28" 4K Ultra HD Monitor L28TN4K TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety Info &
More informationANALOGUE DEMODULATOR OWNERS MANUAL
ANALOGUE DEMODULATOR OWNERS MANUAL TABLE OF CONTENTS Package Content.... 1 About The ADM5... 2 Front & Rear Panels.. 3 Illustration of Basic Connection... 4 Procedure of Set Up... 5-7 Remote Controller
More informationContents: 1 LANsmart Pro Main Unit 4 Remote Unit: ID1, ID2, ID3, ID4
LANsmart Pro user manual Introduction LANsmart Pro is a hand-held, multifunction Cable Map Tester and Cable Length Meter. It has an integrated Analog and Digital Tone Generator, Port Finder, and Quick
More informationUSER MANUAL. VP-424 HDMI to HDMI Scaler MODEL: P/N: Rev 2
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-424 HDMI to HDMI Scaler P/N: 2900-000765 Rev 2 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationFCC Compliance Statement
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device
More informationModel 1476-C SuperQuad HR
Model 1476-C SuperQuad HR Installation and Operating Instructions Table of Contents Page Table of Content... 2 System Description... 3 Features... 3 Installation... 4 Internal Setups... 4 Connections...
More informationPREFACE. FCC Compliance Statement
FCC Compliance Statement PREFACE This device complies with part 15 of the FCC Rules. Opeartion is subjected to the following two conditions: 1. This device may not cause harmful interference, and 2. This
More informationMONOPRICE. BitPath AV VGA Wireless Transmitter & Receiver Kit, 200m. User's Manual P/N 16224
MONOPRICE BitPath AV VGA Wireless Transmitter & Receiver Kit, 200m P/N 16224 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention
More informationTable of Contents. APPENDIX A...12 TFT LCD Monitor Specifications 12. APPENDIX B...13 APPENDIX C...14 Troubleshooting Procedures 14 PREFACE...
Table of Contents CHAPTER 1...1 Unpacking 1 Identifying Components 2 The LCD Monitor Front View 2 The LCD Monitor Rear View 3 Adjusting the Tilting Angle 3 Raising Your Monitor to an Upright Position and
More information