TriLIN Program Utility TPU_ TriLIN Programming Manual
|
|
- Lydia Sims
- 5 years ago
- Views:
Transcription
1 Program Utility TPU_2.8.2 TriLIN Programming Manual
2 1. Programming the electronics a. Tool necessary Power supply V DC Computer with appropriate USB port and a Windows Operating System (We recommend Windows 7 or higher) LPU software Programming cable Possibly a voltmeter (Amperemeter) for the new comparison of the analogue outputs and functional test b. Read-out from the electronics Supplying the electronics with voltage, connecting the programming cable and opening the software. "COM Port" tab and then choose an appropriate port from the list Reading out from the electronics with the help of the "Read EE" button. If the data is not read out correctly, the operation must be repeated. TrigasDM GmbH September
3 c. Importing the calibration curve A Trigas calibration file "*.sav" is necessary for the programming Choose the option "Load F/V kcurve" in the "File" menu for temperaturecompensated programming (Frequency/Viscosity vs. K-factor) / Refer to Section 4.3. Choose optional "Load F kcurve" for non-temperature compensated programming (Frequency vs. K-factor). After the data has been reloaded, the serial number must be compared with that of the calibrated flow meter. Optional: Manual entry of the calibration curve is necessary only if the data is not available to you. NOTE The values must be entered with a dot as the decimal point separator. e.g instead of 15,46 d. Adjusting the electronics Cut-off (ms) Maximum waiting time for completing a signal period. If this time gets exceeded, no input signal gets detected and all outputs are set to zero. Update rate (ms) Measurement period before a measurement result is obtained and calculated. Special case: "0" means that the calculation is already taking place after one pulse. Recommendation: Cut Off = 2 Update Rate TrigasDM GmbH September
4 Timebase (sec.) Time constant for conversion from the K-factor and flow units. o 1 = xxx/sec. o 60 = xxx/min. o 3600 = xxx/hour Minimum frequency (Hz) Lowest frequency (Leakage flow rate). Below the frequency, the TriLIN displays zero at all outputs. Crystal factor Correction factor for internal time base. Use Volts Input 0 PT100 Input 1 Analog Input (analog Temp.) TriLIN can use as temperature input PT100, or analog temperature signal 0-10V e.g. 0 10V = C Attention! To use the input, please contact the manufacturer. Mode Operating mode of the electronics. Mode Compensation Analogue output Frequency output 0 UVC Volumetric Volumetric 1 None Volumetric Volumetric 2 UVC Mass Volumetric 3 None Mass Volumetric 4 UVC Volumetric Mass 5 None Volumetric Mass 6 UVC Mass Mass 7 None Mass Mass Version Should not be changed. Pt100 K-factor (bits to Ohm) K-factor of the PT100 input. Should be corrected only when determining deviations of temperature input. TrigasDM GmbH September
5 e. Liquid data changes The data pertaining to the media can be corrected whenever desired. To do this, choose the option "Load Fluid" in the "File" menu in order to load the new data. The table can also be edited manually as an option. NOTE The values must be entered with a dot as the decimal point separator. e.g instead of 15,46 f. Scaling the outputs Frequency output You only assign the desired scaling in the fields. You can set the units with "Mode" and "Time Base". e.g.: Mode 0: Frequency output, volumetric Time Base 60 per minute Flow / Frequency l/min. = Hz TrigasDM GmbH September
6 Flow, analogue output Mode 0: Analogue output, volumetric Time Base 60 per minute l/min. = 0-10 V (possibly 4-20 ma) Volts (bits) A/D value is calculated automatically Temperature, analogue output C = 0-10 V (possibly 4-20 ma) g. Programming Press the "Write EE" button to program the electronics. After successful programming, the message appears: Attention! The period of time after pressing the "Write..." and the "Succes" message should be 3sec. If not, the process should be performed again. TrigasDM GmbH September
7 Run Live After programming, the program enables the data to be checked. The Live mode is started by pressing the "Run Live" button. h. Saving data Save the settings in the "File" menu option with "Save All" (*.lin) If you need further information, please contact us. TrigasDM GmbH September
8 i. Printing the data You need Excel 2010 or later to print the data. Open the Excel table enclosed. Confirm the security warning with "Activate contents" Load the saved data with the "Load LIN" button. Enter the serial number of the electronics. Print out the report. TrigasDM GmbH September
9 2 Adjusting the analogue outputs NOTE The adjustment should be carried out only with a calibrated voltmeter or ammeter. Connect the electronics as you do for programming with the data cable and power supply. Connect the voltmeter (or ammeter) to the analogue output to be calibrated. Read out from the electronics with "Read EE". There are arrow keys and scroll bars located to the right side of the scaling fields with the help of which the bit values of the respective analogue outputs can be changed. With the upper scroll bar, you can set the minimum value on the multimeter (e.g. 0 V for 0-10 V), and then with the lower scroll bar you can set the maximum value (e.g. 10 V for 0-10 V). Press STOP at the end -> repeat this for the second output. Press the "Write EE" button to program the electronics. TrigasDM GmbH September
10 3 Adjusting the PT100 input NOTE You should carry out this adjustment only with a calibrated resistance decade Connect the electronics as you do for programming with the data cable and power supply. Connect the decade at the temperature input and set 100 Ω. Read out from the electronics with "Read EE" Enter 100 in the calibration field and press the "Calculate" button The PT100 K- factor is recalculated. Press the "Write EE" button to program the electronics. TrigasDM GmbH September
11 4 TriLIN pin assignments Terminal block assignment: TERMINAL DESCRIPTION TRILIN TRILIN +TEMP V DC supply input 2 0 V 3 Sensor input + 4 Sensor input - 5 Analogue flow output 6 GND 7 Analogue temperature output 8 RTD PT100 supply + 9 RTD PT100 sensor + 10 RTD PT100 sensor - 11 RTD PT100 sensor V DC temperature input 13 5 V (TTL pulse) frequency output 14 GND 15 NC 16 NC TrigasDM GmbH September
12 5 Trouble shooting Electronics has no output signal a. Check supply voltage (9-32V DC) i. Standard current consumption is (depending on the configuration) up to 40mA. - Current > 100mA - board defective. - Current = 0 ma - electronics connected incorrectly. b. Flowmeter functionality check i. Attention! The turbine should not be tested with compressed air - turbine may be damaged. ii. Flow simulation: turbines pickoff evaluation Remove pickoff from the turbine and move an iron element (not stainless steel) under the pickoff back and forth. iii. Pickup Resistance Measuring - between pin 1 and 8 RF Sensor: 10Ω +/- 15% c. Check the condition of the electronics (if available) connect electronics with PC and RUN LIVE Switch Mode Programming - Point Baseline value appears to be wrong a. If a problem is noted - RUN LIVE check mode. Compare Analog temperature output versus medium (liquid, gas) temperature. TrigasDM GmbH September
13 Customer service If you should require customer service for your TrigasDM products, please contact our customer service department. All requests for information concerning a specific measuring instrument must include the type and serial number of the measuring instrument. We will provide you with all possible assistance over the phone. If your equipment has to be examined or repaired at our plant, whether within the warranty period or after its expiration, our customer service department will issue you with an authorisation number, which is used to initiate our quick and efficient customer service processing. On receipt at our plant, your equipment will be repaired or replaced without delay and returned to you within the shortest period possible. Please do not return any products without an authorisation number. TrigasDM GmbH Tel.: Erdinger Str. 2b Fax: info@trigasdm.com Neufahrn, Germany TrigasDM GmbH September
800 Displaying Series Flowmeter
TECHNICAL PRODUCT INSTRUCTION SHEET 800 Displaying Series Flowmeter OVERVIEW The principle of operation is very simple. A jet of liquid is directed at a free running Pelton wheel turbine in a specially
More informationTriple RTD. On-board Digital Signal Processor. Linearization RTDs 20 Hz averaged outputs 16-bit precision comparator function.
Triple RTD SMART INPUT MODULE State-of-the-art Electromagnetic Noise Suppression Circuitry. Ensures signal integrity even in harsh EMC environments. On-board Digital Signal Processor. Linearization RTDs
More informationHD-CM HORIZON DIGITAL CABLE METER
HD-CM OFF! Max RF i/p = +17dBm 75Ω Max AC/DC i/p = 120Vrms MENU INPUT ON HORIZON DIGITAL CABLE METER Horizon Global Electronics Ltd. Unit 3, West Side Flex Meadow Harlow, Essex CM19 5SR Phone: +44(0) 1279
More informationREMOTE I/O R30 SERIES. PC CONFIGURATOR SOFTWARE Model: R30CFG Ver Users Manual
REMOTE I/O R30 SERIES PC CONFIGURATOR SOFTWARE Model: R30CFG Ver. 1.13 Users Manual 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Tel: +81-6-6659-8201 Fax: +81-6-6659-8510 http://www.m-system.co.jp/
More informationOperating instructions Electronic preset counter Type series 717
Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range
More informationOPERATION MANUAL JENDPM008 THERMOCOUPLE PANEL THERMOMETER. TIP TEMPerature Products 340 W Broad Street Burlington, NJ 08016
OPERATION MANUAL JENDPM008 THERMOCOUPLE PANEL THERMOMETER TIP TEMPerature Products 340 W Broad Street Burlington, NJ 08016 1-800-TIP-TEMP Tel. (609) 239-1900 Fax (609) 239-1911 www.tiptemp.com GENERAL
More informationMT03A Electronic converter for flow rate transmitters
Instructions manual MT03A Electronic converter for flow rate transmitters The art of measuring R-MI-MT03A Rev.: 0 English version PREFACE Thank you for choosing a Tecfluid S.A product. This instruction
More informationFTS84/85 Feature Application Field. Temperature & Humidity / Flow Measuring Specialist. Monitor gas and flow for industrial process
FTS84/8 Feature Application Field Capable of temperature compensation and linear adjustment Double line character : air velocity & temperature Switch for physical quantity:[m/s] [ft/s] [km/h] [mph] [knot]
More informationElectronic converter for level transmitters MT03L Instructions manual
Electronic converter for level transmitters MT03L Instructions manual R-MI-MT03L Rev.: 1 English version PREFACE Thank you for choosing the MT03L converter from MT03 series of Tecfluid S.A. This instruction
More informationST-4000 SIGNAL LEVEL METER
ST-4000 SIGNAL LEVEL METER Table of Contents Features / Specifications.... 1 Keypad Illustration....... 2 Keypad Controls.... 2 Getting Started: Powering the Meter.... 3 Quick Use Instructions.. 3 Main
More informationST-4000D SIGNAL LEVEL METER
ST-4000D SIGNAL LEVEL METER Rev 100606 Table of Contents Features / Specifications.... 1 Keypad Illustration....... 2 Keypad Controls.... 2 Getting Started: Powering the Meter...... 3 Quick Use Instructions.....
More informationOperating Instructions BTX-1 Series Digital Band Tension Meter
Operating Instructions BTX-1 Series Digital Band Tension Meter TABLE OF CONTENTS 1. WARRANTY POLICY... 3 2. SPECIFICATIONS... 4 3. SAFETY AND MAINTENANCE... 5 4. INSTRUMENT FEATURES... 6 Calibration and
More informationNoise Detector ND-1 Operating Manual
Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation
More informationUser Manual. for. Panel mounted instrument
User Manual for Panel mounted instrument Series Compare L3C00-00-20.01E Version 3.0 Min. Max. Chn.1 Chn.2 Rel.1 Rel.2 /Displ. Limburg compare analog Min. Max. Chn.1 Chn.2 Rel.1 Rel.2 /Displ. Limburg compare
More informationInstallation and Setting up Instructions for the 990 Signal Conditioning Instrument
Installation and Setting up Instructions for the 990 Signal Conditioning Instrument Contents Page 1.0 Overview... 3 2.0 Installation.. 4 2.1 Electrical connections... 4 2.2 Cable selection... 4 2.3 Electrical
More informationRevision 1.2d
Specifications subject to change without notice 0 of 16 Universal Encoder Checker Universal Encoder Checker...1 Description...2 Components...2 Encoder Checker and Adapter Connections...2 Warning: High
More informationTECHNICAL MANUAL DRAW-WIRE DISPLACEMENT TRANSDUCER TYPE DWT
RDP Customer Document TECHNICAL MANUAL DRAW-WIRE DISPLACEMENT TRANSDUCER TYPE DWT Doc. Ref CD1004L BS EN ISO 9001 Certificate No. FM13141 Affirmed by Declaration of Conformity USA & Canada RDP Electrosense
More informationTransmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
More informationLt DELTA USA, Inc
Infrared LOOP SCANNER Rota-Sonde TS2006 Infrared - high sensitivity 480 F or 750 F Quick and easy commissioning Self-monitoring and alarm functions Lt 1037 1 Applications R o t a - S o n d e TS2 0 0 6
More informationCOMPANY. MX 9000 Process Monitor. Installation, Operating & Maintenance Manual AW-Lake Company. All rights reserved. Doc ID:MXMAN082416
COMPANY MX 9000 Process Monitor Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:MXMAN082416 1 Table of Contents Unpacking...3 Quick Guide...3 Connect to Sensor...3
More informationDICKSON ES120/ES120A DICKSON. Electronic Signal Data Logger. Specifications. Applications, Features, & Getting Started. Instructions / Operating
/A Electronic Signal Data Logger Contents: Product Applications and Useful Features Product Transmitter / DicksonWare Software Product Frequently Asked Questions Warranty / Software & FAQs & Product Applications
More informationVXF17 QUICKSTART GUIDE. 17" Full HD 3G-SDI/HDMI Rackmount Studio and Field Monitor
VXF7 QUICKSTART GUIDE 7" Full HD 3G-SDI/HDMI Rackmount Studio and Field Monitor What s Included x VXF7 Monitor x AC Adapter x Table Stand (installed) x Rack Ears (installed) CHECKED BY www.ikancorp.com
More informationModel IQ4-PC User Manual Revision Date:
Basic Specifications Supply Volts 230V 50/60Hz ±15% 115V 50/60Hz ±15% 24V DC (isolated) ±15% Power Consumption Max. 3VA (IQ4-PC-R0) Max. 6VA (IQ4-PC-R2-PSI24-RT) Operating Temperature -5 ~ +60 C Operating
More informationConfiguring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display.
Configuring the Stack ST8961 VS Module when used in conjunction with a Stack ST81xx series display. Your Stack ST8961 VS module allows you to synchronize, overlay, and record data available on your Stack
More informationAP-40. AP-40 Series Features Industry s smallest-sensor head Ultra lightweight High-speed response Two-color LED digital pressure display
AP-34 Separate Amplifier Type Sensor Series Features Industry s smallest-sensor head Ultra lightweight High-speed response Two-color LED digital pressure display Description Industry's smallest & lightest
More informationAurora Grid-Tie Installation Instructions (Model Number: PVI-3.0-OUTD-US-W) Revision 4.1
Aurora Grid-Tie Installation Instructions (Model Number: PVI-3.0-OUTD-US-W) Revision 4.1 Contents 1) Grid-Tie Installation Block Diagram... 3 2) Installation Steps.... 4 2.1) Initial Setup.... 4 2.1.1)
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationManual. Analog (U/I) Sendix M3661 / M3681. Sendix M3661R. Sendix M5861. Absolute multiturn encoder. Order code: 8.M36X1.XXXX.XX12
R60722.0002 - Index 3 Analog (U/I) Manual Absolute multiturn encoder Order code: 8.M36X1.XXXX.XX12 Order code: 8.M3661R.XXXX.XX12 Order code: 8.M5861.XXXX.XX12 Publisher Kübler Group, Fritz Kübler GmbH
More informationFTS84/85 Feature Application Field. Temperature & Humidity / Flow Measuring Specialist. Monitor gas and flow for industrial process
FTS84/8 Feature Application Field Capable of temperature compensation and linear adjustment Double line character : air velocity & temperature Switch for physical quantity:[m/s] [ft/s] [km/h] [mph] [knot]
More information2 WIRE - LOOP POWERED TRANSMITTER FOR PT100 AND NI100 PROBES
EN K20RTD 2 WIRE - LOOP POWERED TRANSMITTER FOR PT00 AND NI00 PROBES General Description The K20RTD instrument converts a temperature signal read by a PT00 (EN 60 75) or NI00 probe with connection by 2,
More informationTroubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing.
Product Data Electrical Data SST (Transmitter) SSR (Receiver) Supply voltage 18 30 V dc Max. Voltage ripple 15 % (within supply range) Current consumption 100 ma (RMS) 75 ma Digital - 100 ma Max. outputs
More informationElectronic converter for flowmeters MT03F Instructions manual
Electronic converter for flowmeters MT03F Instructions manual R-MI-MT03F Rev.: 0 English version PREFACE Thank you for choosing the MT03F converter from MT03 series of Tecfluid S.A. This instruction manual
More informationPRELIMINARY INFORMATION. Professional Signal Generation and Monitoring Options for RIFEforLIFE Research Equipment
Integrated Component Options Professional Signal Generation and Monitoring Options for RIFEforLIFE Research Equipment PRELIMINARY INFORMATION SquareGENpro is the latest and most versatile of the frequency
More informationSet Point Controller OC557. Operator s Manual
OC557_Manual_GB1206D Set Point Controller OC557 4 20mA Input Operator s Manual METRIX ELECTRONICS LTD. Tel: +44 (0)845 034 3234 Minchens Court, Minchens Lane Fax: +44 (0)845 034 3233 Bramley, Tadley, Hampshire
More informationCARLO GAVAZZI Automation Components
CARLO GAVAZZI Automation Components UDM 35/40 Digital Panel Meter Programming Guide Index Description 2 Programming Fundamentals 3 Access to Programming Mode/Password Protection 4 Programming 5-18 Inputs
More informationARC HEIGHT CONTROL (ARC VOLTAGE CONTROL) MODEL : HAC-01-A-1M
ARC HEIGHT CONTROL (ARC VOLTAGE CONTROL) MODEL : HAC-01-A-1M 1. INTRODUCTION 1-1 Figures - It is a kind of unit to keep up Arc height between work-piece and torch by controlling the voltage of arc; if
More informationAuxiliary states devices
22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary
More informationMortara X-Scribe Tango+ Interface Notes
Mortara X-Scribe Tango+ Interface Notes To setup Tango+ with the X-Scribe stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate
More informationmedlab One Channel ECG OEM Module EG 01000
medlab One Channel ECG OEM Module EG 01000 Technical Manual Copyright Medlab 2012 Version 2.4 11.06.2012 1 Version 2.4 11.06.2012 Revision: 2.0 Completely revised the document 03.10.2007 2.1 Corrected
More informationPicoScope 4000 Automotive PC Oscilloscopes
PicoScope 4000 Automotive PC Oscilloscopes User's Manual ps4000a.en-1 Copyright 2008 Pico Technology Ltd. All rights reserved. Contents I Contents 1 Introduction...1 1 Overview...1...1 2 Minimum PC requirements...2
More informationMICROPROCESSOR CALCULATION MODULE - S2000
MICROPROCESSOR CALCULATION MODULE - S2000 Complying equipments with prescriptions on electromagnetic compability (standard 89/336/CEE.) Industrial environment, reference standard : EN 50081-2 EMISSION
More information4.9 BEAM BLANKING AND PULSING OPTIONS
4.9 BEAM BLANKING AND PULSING OPTIONS Beam Blanker BNC DESCRIPTION OF BLANKER CONTROLS Beam Blanker assembly Electron Gun Controls Blanker BNC: An input BNC on one of the 1⅓ CF flanges on the Flange Multiplexer
More informationHow to Order. Flow rate (l/min) Applicable models PFA710, PFA750. Nil
Integrated Display Type Flow rate range 0 2 5 Symbol 0 02 03 0 Specifications ow Order PFA7 0 0 27 0l/min 5 l/min 0 00l/min 20 200l/min 0l/min Port size /8 / 3/8 /2 Model Measured fluid Detection type
More informationAmbiflex MF620 USER GUIDE
Ambiflex MF620 USER GUIDE 1 st August 2001 AMBIFLEX MF620 - USER GUIDE CONTENTS Page No MF620 Overview 2 MF620 Connection Details 3 Technical Specification 4 Standby Display 6 User Facilities 7 Status
More informationPulseFlow FP100 Pulse to 4 20mA Flow Converter (Flow Rate Transmitter / Totalizer / Indicator)
PulseFlow FP100 Pulse to 4 20mA Flow Converter (Flow Rate Transmitter / Totalizer / Indicator) Submeter Solutions, Inc. PulseFlow FP100 Submeter Solutions, Inc., 800-64METER Page 1 Table of Contents: Installation
More informationZIRCONIA OXYGEN ANALYZER CONVERTER
Service Manual ZIRCONIA OXYGEN ANALYZER CONVERTER TYPE: ZKM INZ-TN5A0845b-E Contents 1. GENERAL...1 1.1 ZKM1 Internal constitution...1 1.2 ZKM2 Internal constitution...1 1.3 Description on display/setting
More informationOcean Sensor Systems, Inc. Wave Staff, OSSI F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff
Ocean Sensor Systems, Inc. Wave Staff, OSSI-010-002F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff General Description The OSSI-010-002E Wave Staff is a water level sensor that
More informationContents: 1 LANsmart Pro Main Unit 4 Remote Unit: ID1, ID2, ID3, ID4
LANsmart Pro user manual Introduction LANsmart Pro is a hand-held, multifunction Cable Map Tester and Cable Length Meter. It has an integrated Analog and Digital Tone Generator, Port Finder, and Quick
More informationInstruction Manual MODEL RSP SANITARY ELECTRONIC PRESSURE TRANSMITTER
Instruction Manual Anderson Instrument Co. Inc. 156 Auriesville Road Fultonville, NY 12072 1-800-833-0081 Fax 518-922-8997 www.andinst.com Instrument Model Number Instrument Serial Number MODEL RSP SANITARY
More informationSCALE & WEIGHT DISPLAYS
The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters
More informationTable of contents 1. INTRODUCTION GENERAL CONTENTS OF PACKAGE GENERAL USE OF THE EQUFLOW 6100 D/A CONVERTER STORAGE..
Installation instructions and user s guide Equflow 6100 D/A Converter Please read this manual carefully before installation and use of the converter. 6100 D/A Converter Type: 6100DACONDC03 Despite effort
More informationDynatel Advanced Cable Locator 2250
3 Dynatel Advanced Cable Locator 2250 Quickly and Accurately Identify Underground Assets Pinpoint exact cable path and depth quickly and easily with this lightweight, easy-to-handle unit The 3M Dynatel
More informationManual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.
Manual Title: 744 Users Supplement Issue: 6 Part Number: 691287 Issue Date: 4/06 Print Date: September 1998 Page Count: 8 Revision/Date: 1, 2/99 This supplement contains information necessary to ensure
More informationL, LTC, LTM, LT are registered trademarks of Linear Technology Corporation. Other product
DESCRIPTION WARNING! Do not look directly at operating LED. This circuit produces light that can damage eyes. Demo Circuit 1265 QUICK START GUIDE LTC3220/LTC3220-1 360mA Universal 18-Channel LED Driver
More informationCOLOR TFT LCD MONITOR. Manual
COLOR TFT LCD MONITOR Manual Safety defended: Properly maintains your system to be possible to guarantee its service life and to reduce the damage risk. It should avoid the damp and exceeding temperature
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS 1. Read, follow and keep these instructions safely. 2. Heed all warnings. 1. Do not use this apparatus near water. 2. Clean only with dry cloth. 3. Do not block any ventilation
More informationDMP 331i DMP 333i. Precision Pressure Transmitter. Stainless Steel Sensor. accuracy according to IEC 60770: 0.1 % FSO
DMP i DMP i Precision Pressure Transmitter Stainless Steel Sensor accuracy according to IEC 600: 0. % FSO from 0... 00 mbar up to 0... 600 bar Output signal wire:... 0 ma wire: 0 0 V others on request
More informationAZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR 15.0 OPEN FRAME MONITOR
AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR 15.0 OPEN FRAME MONITOR PART NUMBER: AOM150X03 SERIES DATE: SEPT 04, 2008 1. Introduction: 1.1 About the Product AOM150Xxx 15.0 Open Frame Monitor
More informationWall-/Pipe-Mount Level Indicator
Data Sheet SS/_4 Wall-/Pipe-Mount Level Indicator High visibility 5-digit LED display clear multi-functional indication Analog and 2-relay outputs as standard high, low, latch and rate alarms, plus isolated
More informationPicoScope 2000 Series PC Oscilloscopes
PicoScope 2000 Series PC Oscilloscopes User guide I PicoScope 2000 Series User Guide Table of Contents 1 Introduction...2...2 1 Overview...2 2 Safety symbols...3 3 Safety warning...3 4 FCC notice 5 CE
More informationQuick Start. RSHS1000 Series Handheld Digital Oscilloscope
Quick Start RSHS1000 Series Handheld Digital Oscilloscope General Safety Summary Carefully read the following safety precautions to avoid personal injury and prevent damage to the instrument or any products
More informationOperating Instructions ACX-Series Digital Aircraft Cable Tension Meter
733 S. Bowen Street Longmont, CO 80501 USA Phone: (303) 702-1980 Fax: (303) 702-1982 E-mail: sales@tensitron.com Web Site: www.tensitron.com Operating Instructions ACX-Series Digital Aircraft Cable Tension
More informationVorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630)
Vorne Industries 87/719 Analog Input Module User's Manual 1445 Industrial Drive Itasca, IL 60143-1849 (630) 875-3600 Telefax (630) 875-3609 . 3 Chapter 1 Introduction... 1.1 Accessing Wiring Connections
More informationOperating Instructions
Broadcast A/V Division Model No. M-LYNX-702W Dual 7 High Resolution Rack Mount Display with Waveform Operating Instructions V.1.0 Table of Contents 1. PRODUCT DESCRIPTION... 3 2. MENU SETTING... 6 3. SPECIFICATIONS...
More informationFOTS100 User Manual. BIOPAC Systems, Inc. Opsens Inc. 42 Aero Camino, Goleta, CA Tel (805) , Fax (805)
FOTS100 User Manual BIOPAC Systems, Inc. 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066, Fax (805) 685-0067 WWW.BIOPAC.COM 1 WARRANTY All products manufactured by Opsens inc. are warranted to be free
More informationMicro-DCI 53ML5100 Manual Loader
Micro-DCI 53ML5100 Manual Loader Two process variable inputs Two manually controlled current outputs Multiple Display Formats: Dual Channel Manual Loader, Single Channel Manual Loader, Manual Loader with
More information7 3G -SDI Monitor w/ Signal Conversion QUICKSTART GUIDE
What s included x Monitor x AC Adapter x Camera Shoe Mount (SM-0) x DV Battery Plate (Check one) Checked by DV BATTERY PLATES -: Canon 900, Sony L, Panasonic D Battery Plates VX7 c-: Canon E6, Nikon EL,
More informationModule 28 Scan Tool Advanced
Module 28 Scan Tool Advanced Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443 Greensboro,
More informationC-net WIND. User s Guide
C-net WIND User s Guide EMC Directive 89/336/EEC This product has been designed to be compliant with the above EMC Directive. Maximum performance and compliance with the EMC Directive can only be ensured
More informationNS-3 RF Noise Source Operation Manual
RF Noise Source Operation Manual Version 2.04 June 3, 2016 SPECIFICATIONS Frequency... Maximum output level... Output flatness... (at max output level) Impedance... Displayed level... Repeatability...
More informationOperating Instructions
CNTX Contrast sensor Operating Instructions CAUTIONS AND WARNINGS SET-UP DISTANCE ADJUSTMENT: As a general rule, the sensor should be fixed at a 15 to 20 angle from directly perpendicular to the target
More informationDH7-DK QUICKSTART GUIDE. DH7 4K Support HDMI On-Camera Field Monitor Deluxe Kit
DH7-DK QUICKSTART GUIDE DH7 4K Support HDMI On-Camera Field Monitor Deluxe Kit What s Included 1 x DH7 Monitor 1 x AC Adapter 1 x Camera Shoe Mount 1 x Screen Cleaning Wipe 1 x Screen Protection Film 1
More informationDynamic Cable Rating Model Guidelines
lines Introduction This document describes how to set up, configure and run the Dynamic Cable Rating model in Ipsa. The Dynamic Cable Rating model (DCR) has been developed for the WPD FALCON project by
More informationBE3-GPR GENERATOR PROTECTIVE RELAY
BE3-GPR GENERATOR PROTECTIVE RELAY Behind-the-Panel Mounting Semi-flush Mounting Basler Electric s BE3-GPR generator protective relay offers multiple protective features in a single package. Its microprocessor-based
More informationPanel cutout required: 1.772" x 3.622" (45mm x 92mm) 1.76" (45mm) 2.45" (62mm) 3.20" (81mm) 3.60" (91mm) 0.59" (15mm) Special Features
NEMA4X, IP65 Front Bezel Meter with Relays Option RELAY2 RELAY1 24V OUT POWER 4 3 2 1 6 5 2 1 2 1 NO NC COM NO NC COM RTD TC P P RTD 3 4 1 2 5 TC 6 SWITCH Rear View Gasket APM765 Panel Meter Description
More informationPicoScope 3000 Series Automotive User guide
PicoScope 3000 Series Automotive User guide PS3000A044 v1.0 I PicoScope 3000 Series Automotive PC Oscilloscopes Table of Contents 1 Introduction...2...2 1 Overview...2 2 Minimum PC requirements...2 3 Installation
More informationFRQM-2 Frequency Counter & RF Multimeter
FRQM-2 Frequency Counter & RF Multimeter Usage Instructions Firmware v2.09 Copyright 2007-2011 by ASPiSYS Ltd. Distributed by: ASPiSYS Ltd. P.O.Box 14386, Athens 11510 (http://www.aspisys.com) Tel. (+30)
More informationHDMI 1X4 Distribution Amplifier (Splitter)
HDTrinity HDMI 1X4 Distribution Amplifier (Splitter) USER MANUAL Model No. SS04 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully
More informationBroadcast A/V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual
Broadcast A/V Division M-LYNX-702 V.3 Dual 7 LCD Display User Manual 1. Package Includes Table of Contents 1. Package Includes Table of Contents 01 02 One M-LYNX-702 Monitor One universal AC power adapter
More informationISOMAG THE FRIENDLY MAG METER. Gas, mists or vapours Zone 0 1G Gas, mists or vapours Zone 1 2G. Gas, mists or vapours Zone 2 3G
ISOMAG THE FRIENDLY MAG METER Converter EX CONVERTER Hazardous area Categories according to 94/9/CE Directive Gas, mists or vapours Zone 0 1G Gas, mists or vapours Zone 1 2G Gas, mists or vapours Zone
More informationBroadcast A / V Division M-LYNX-702 V.3. Dual 7 LCD Display. User Manual
Broadcast A / V Division M-LYNX-702 V.3 Dual 7 LCD Display User Manual Table of Contents Table of Contents 1. Package Includes 2. Product Description 2.1 Front Panel 2.2 Rear Panel Connections 3. On-Screen
More informationOn-screen display signal strength meter Version 1.02
OSD-SSM On-screen display signal strength meter Version 1.02 Copyright 2000 Intuitive Circuits, LLC D escription OSD-SSM is an on-screen display overlay board with analog to digital circuitry which continuously
More informationProduct Manual MNX10015 / REV C MODEL SB142, SB242. Dual Output Series Switch Boxes
Product Manual MNX10015 / REV C MODEL SB142, SB242 Dual Output Series Switch Boxes Contents Section I Overview Introduction.... 2 Description... 2 Section II Installation Mounting... 3 Electrical Connections...
More informationFits the Leopard Family FREQ./RPM INPUT MODULE WITH 24 V EXC.
Fits the Leopard Family FREQ./RM INUT MODULE WITH 24 V EXC. Low-pass Filter., 2 khz,. Switching Comparator. revents false triggering. Input Connector. Freq. Input. 24 V Excitation. Sensor. Mag, Namur,
More informationTRANSCENSION 6-CHANNEL DMX DIMMER PACK (order code: BOTE40) USER MANUAL
www.prolight.co.uk TRANSCENSION 6-CHANNEL PACK (order code: BOTE40) USER MANUAL SAFETY WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this
More informationAPPLICATIONS. Automatic warehouse. Trasportation lines
INDUCTIVE TUBULAR SENSOR M12 SERIES There are millions of inductive sensors deployed in almost every area of factory automation. They detect metal objects contactless and are distinguished by a long operating
More informationAEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE
AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE Thank you for purchasing a TSI AeroTrak Model 9110 Portable Airborne Particle Counter (particle counter). This guide will help you
More informationNI-DAQmx Device Considerations
NI-DAQmx Device Considerations January 2008, 370738M-01 This help file contains information specific to analog output (AO) Series devices, C Series, B Series, E Series devices, digital I/O (DIO) devices,
More informationDS 400 P. Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing. on hygienic process connections
Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing Description The electronic pressure switch is the successful combination of hygienic process connections with flush welded
More informationElectronic Pulse Counter Combination device
Electronic Pulse Counter Combination device measuring monitoring analysing Input: pulse counter, time meter Display: 6-digit LED Height of digits: 14/8 mm Operation with front-panel buttons Material: plastic
More information1 Output 1 operation. 3 Pressure unit display. 4 Main display Large 4-character LCD display. 5 Sub-display Small 4-character LCD display.
ure Sensor DP-100 Series INSTRUCTI MANUAL High-performance Digital Display For use outside Japan MEUML-DP100 V1.1 Thank you for purchasing products from Panasonic Electric Works SUNX Co., Ltd. Please read
More informationIRIG-B PTP Clock Converter Output Module Hardware Installation Manual
IRIG-B PTP Clock Converter Output Module Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: May 2012 Version: V1.2 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678
More informationCURRENT INJECTION RELAY TESTER CR-100. ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M / 05A ) (c) CIRCUTOR S.A.
CURRENT INJECTION RELAY TESTER CR-100 ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M 981 329 / 05A ) (c) CIRCUTOR S.A. ---- CURRENT- TIME TRIP TESTER CR-100 --------------- Page. 2 CURRENT INJECTION
More informationProgramming instructions Software Version 5
Programming instructions Software Version 5 0250032E/ February 2014 MAXX GmbH, 2014. All rights reserved. Printed in Germany Contents PROGRAMMING 4 Assignment and function of keys 4 NAVIGATION 5 Menu variants:
More informationDisplays Open Frame Monitor Model Number: AND-TFT-150Bxx
Displays 15.0 Open Frame Monitor Model Number: AND-TFT-150Bxx The AND-TFT-150Bxx 15.0 Open Frame Monitor series are rugged, high performance Industrial LCD Monitors, designed for commercial and industrial
More informationFOUR CHANNEL USB RECORDER PCRU01. User manual. Table of Contents
FOUR CHANNEL USB RECORDER PCRU01 User manual Table of Contents Features 2 Specifications 2 hardware 2 software: 2 system requirements 2 Software installation 2 SAFETY and WARNINGS 3 Warranty 3 Connections
More informationLCD Thermometer / Clock S No. 1253
Installation and Operating Manual LCD Thermometer / Clock S No. 1253 The 3 fold thermometer with crystal clock is purpose build for the mounting in caravans, boats and intervention vehicles. Please read
More informationIndustriefunkuhren. Technical Manual. IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C / AFNOR NF S87-500
Industriefunkuhren Technical Manual IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C37.118 / AFNOR NF S87-500 Module 7628 ENGLISH Version: 02.01-06.03.2013 2 / 20 7628 IRIG-B
More informationGuide for installers. METTLER TOLEDO MultiRange System solution analog Ex1. Hazardous area. Safe area
Guide for installers METTLER TOLEDO MultiRange System solution analog Ex1 Hazardous area Safe area System solution analog Ex1 Contents Contents Page 1 Safety precautions... 2 2 System overview... 3 2.1
More informationDS 200 P DS 200 P. Electronic Pressure Switch with Flush Process Connection
with Flush Process Connection piezoresistive pressure sensor up to independent contacts, configurable optional: analogue output Exprotection (for wire) cooling element up to 00 C nominal pressure ranges
More information