DSR-4520X IRD Set-Up and Configuration Guidelines for Direct Reception on Galaxy 13
|
|
- Clarissa Lambert
- 6 years ago
- Views:
Transcription
1 DSR-4520X IRD Set-Up and Configuration Guidelines for Direct Reception on Galaxy 13 Version 1.9, 09/12/06
2 This document is intended as a supplement to and not as a substitute for the Operator Guide provided by Motorola to its customers for this product. Certain portions of the Motorola document have been excerpted and revised by HBO Engineering to fit the HBO-specific application. This document details the nuances of IRD installation and configuration that are specific to receiving HOD and MaxOD from HBO on Galaxy 13. It is assumed that the reader has become familiar with the Motorola document. When the IRD is ordered from the authorized Motorola Distributor, the PO should specify that the IRD will be utilized for the reception of HOD/MaxOD. This should help ensure that the IRD delivered is loaded with the proper version of firmware. IMPORTANT NOTE: PLEASE CHECK IRD FIRMWARE VERSION BEFORE PROCEEDING WITH INSTALLATION! Main Code must be at 12C or higher. Ethernet Code must be at 0A12 or higher. When powering up the IRD for the first time, please be sure to perform a power-up factory reset to ensure proper boot-up on the current code version. Simply hold in the < and > cursor keys on the front panel of the IRD when power is first applied (for approximately 20 seconds) until the unit boots fully. 2
3 CONFIRMING the IRD Firmware Version It is critical to the proper operation of the IRD for the purposes of receiving HOD and MaxOD content via the IRD Ethernet port that the IRD be at the correct firmware version. When the IRD was ordered, the PO should have specified that the IRD is intended for reception of HOD/MaxOD; Motorola or its authorized distributor should have provided the correct version. This detail must be checked prior to placing the IRD into service. To check the current version of firmware in the IRD, after supplying power to the unit, enter the <Status> submenu through the front panel controls, and navigate to page 2 of that submenu. Below is what you should see on the IRD LCD display. What is critical is the highest version of code available in the unit: Main - Boot : Min : High : 12A:12C:12C Ethernet - Boot : High : 0A10:0A12 <MAIN MENU] FIRMWARE (2/2) [NEXT> Main - Boot:Min:High These three values describe the firmware version for the unit s main processor (Delphi). Boot code may vary. Your IRD should have Main High code at 12C. Ethernet - Boot:High These two values describe the firmware versions for the unit s auxiliary processor (PowerPC), used for processing Ethernet messages. Boot code may vary. Your IRD should have Ethernet High code at 0A12. If the IRD has the correct version of code, proceed with installation and configuration as described below. If it does not, please contact the HOD Hotline at (212) as soon as possible for instructions on how to proceed. During the transition period, HBO will have a satellite code download available to those sites that do not receive IRD s with the correct firmware. 3
4 Connecting the DSR-4520X for HOD/MaxOD Cable connections described in this section are made to the rear panel of the DSR-4520X. 2. RF Input Ports (use RF Port 1 for input from Galaxy 13, Vertical Polarity) 4. Ethernet Port 1 (connect to Catcher Port Eth0 on the MP-CAT using a crossover Ethernet cable) 5. Ethernet Port 2 (not used in this application be careful not to connect Catcher here) 12. Video Out (with OSD) (recommended for troubleshooting/status monitoring) CONNECTING the IRD To Connect the Unit to receive HOD/MaxOD Connect the L-band signal from the V-pol of the antenna already peaked on Galaxy 13 and data grade LNB to one of the RF input ports (RF Port 1 is recommended). Use a DC block if necessary to prevent another receiver's LNB power output from shutting down the DSR-4520X. Only Port 1 of the DSR-4520X provides LNB power. If you are using Port 1 and the LNB is powered from elsewhere be sure to have LNB power disabled on the IRD (see manual). Please confirm that the RF input signal level is between 65dBm and 25dBm (optimal is in the 40dBm range). To view on-screen diagnostics during installation, connect the Video Output on the unit to a video monitor. Diagnostic data is output only on Video 2 Output. Using a standard Ethernet cross-connect (crossover) cable connect the Ethernet Port 1 of the DSR-4520X to the Ethernet 0 port on your Tandberg Media Path Catcher. Note that the crossconnect cable must be CAT-5 unshielded twisted pair, with a length of
5 HBO on Demand/Cinemax on Demand Distribution Network Galaxy 13, Transponder 11 HBO Pitcher via DCII Multiplex Internet Headend DSR-4520X IRD L-Band Freq: 1230 MHz (V-Pol) VCT: 730 VC: 171 ACK/NAK Traffic Ethernet x-over cable Firewall Tandberg Catcher MP-CAT-320 ADI AMS 5
6 CONFIGURING the IRD To Configure the Unit to receive HOD/MaxOD Following are instructions and menu screen samples specific to the reception of HOD and MaxOD from Galaxy 13. Configure RF Port After connecting a feed of Galaxy 13 Vertical polarity downlink to RF input 1 on the IRD, select <RF Ports > from Main Menu and arrow down to the bottom of the menu, set the Active Port to Port 1, and configure as follows: >Active Port = 1 Frequency = 1230 Symbol:Code:Bit = 29.3: 7/8 Combined <MAIN MENU] MANUAL TUNE (10/10) [NEXT> At this point, the DIGICIPHER LED on the front panel of the IRD should be illuminated, indicating acquisition of the satellite signal. If it is not, recheck all settings, RF connections, and antenna pointing. It is recommended to leave the remaining 7 ports in an unconfigured mode, since they will not be used in this application. Set the Port Test parameters according to local requirements. >Satellite = G9 (or G13) Polarity = Vertical Status : Defined <MAIN MENU] PORT 1 SETUP (1/10) [NEXT> NOTE: Even though the satellite is Galaxy 13; the satellite designator, VCT and channel number may reflect Galaxy 9 (G9) to avoid having to reconfigure IRDs already in service. 6
7 Select Channel After configuring the RF port and confirming satellite signal acquisition, give the IRD a few minutes to download the Virtual Channel Table (VCT) from the HBO satellite feed. Then select <Channels> from the Main Menu and configure the Virtual Channel selection as follows: > VCT ID = 730 Channel Number = 171 Provider ID = --- <MAIN MENU] CHANNEL SELECT (1/2) [NEXT> Once the VCT and channel selections are made, the IRD should lock to the Ethernet IP service which is carrying the HOD/MaxOD IP stream. When this occurs the DIGICIPHER LED on the front panel of the IRD should illuminate, and <Data> should look as follows: Confirm Service Acquisition > Asynchronous = Not Defined Isochronous = Not Defined Ethernet - IP = Defined <MAIN MENU] DATA STATUS (1/5) [NEXT> If <Ethernet - IP> displays a <Defined> status, the IRD has acquired the service and will output IP from Ethernet Port 1, which has been connected to the Tandberg Mediapath Catcher. Go back and confirm all front panel LED indicators and settings if Ethernet status is displayed as <Not Defined>. 7
8 Configure IP Address on Ethernet Port 1 In order for the Tandberg Mediapath Catcher to be able to monitor the status of the IRD, it must be assigned an IP address which is known to the Catcher. The same Ethernet Port 1 that is used to deliver content-related data to the Catcher is used for this monitoring. Remember that we do not use Ethernet Port 2 in this application at all. Please configure as follows under the <Data> menu: >IP Address = Subnet Mask = Default Gateway = <MAIN MENU] ETHERNET PORT 1 (3/5) [NEXT> Unless the IRD is separated from the Catcher by a gateway (not recommended), there is no need for the user to be concerned with the Default Gateway setting. While other values may appear after initialization, if no specific address is set, the factory default is shown above. Configure the Relays, Relay Bypass, and Alarm When being utilized for the reception of linear video services the 4520X has certain relay, alarm and relay bypass settings that may be configured to respond to various conditions. In the HOD/MaxOD Configuration these alarms and the relay bypass feature of the IRD are not used. In order to ensure that the IRD does not display false alarm conditions, HBO advises that they be set accordingly. The following two screens are both configurable from the <EXT Hardware> menu as follows: >Relay 1 = Off Relay 2 = Off Relay 3 = Off <MAIN MENU] Relays (1/2) [NEXT> >Bypass Mode = Disabled Alarm Trigger = Off Alarm State = Disabled <MAIN MENU] Alarms (2/2) [NEXT> 8
9 On-Screen Diagnostic Display The Fast Facts 1 and Fast Facts 2 screens of the on-screen diagnostic (OSD) display available on the video output of the IRD (see Motorola manual) contains very useful fields of information that indicate the status of the IRD. A sample of a happy IRD OSD looking at HOD/MaxOD would have a Fast Facts 1 screen that looks something like this: Unit:nnn-nnnnn-nnnnn-nnn VC# = 171 Firmware: 000A12 000A12 VCT ID = 0730 Encryption = Unencrypted Service # = 72 Auth State = Unauthorized Eb/No = Signal State = Locked Sat/Xpndr = G9/10 (or G13) Signal Quality = 75 Virtual Network = nnn Symbol Rate = Msps Polarization =V Frequency = MHz FEC Rate = 7/8 The OSD Fast Facts 1 screen is currently the only place where you can get any detail regarding the quality of the downlinked satellite signal. Without it you only have the DIGICIPHER LED on the front panel of the unit to tell you if the IRD is locked to the satellite signal; the LED indicator does not give you any information with regard to downlink or bit-error margin. If you have difficulty establishing or maintaining lock, or if you have ongoing catch failures, it is useful to check the Eb/No (energy-per-bit/noise spectral density roughly equivalent to a digital S/N figure). A lower than optimal Eb/No will result in a high bit-error rate (BER). At the HBO FEC rate of 7/8, an Eb/No of 8.0 db is necessary to maintain a serviceable BER; an ideal Eb/No is in the 10-12dB range. Signal Quality is a number provided on an arbitrary scale, represents a combination of the input signal level and the BER. This number should always be at or above 75. 9
10 Fast Facts 2 Screen Use this screen if you need to verify that the port definition has taken in the unit configuration. Do not worry if the other RF ports show something other than <>; as long as you have set the active port to Port 1, the IRD will only concern itself with the input signal at that port. Port 1 = G9:V (or G13:V) Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Confirmed Port 8 For General Support please contact the HBO Hotline at: , hodhotline@hbo.com. For Motorola/GI technical support please call
IRD Quick Install Guide
IRD Quick Install Guide Instructions acquiring HBO/Cinemax Programming Motorola DSR-series Digicipher II Commercial Receiver/Decoders* Installation of the Digicipher II IRD involves a simple hook up and
More informationDSR-6050 Commercial Integrated Receiver/ Transcoder Operator Guide
DSR-6050 Commercial Integrated Receiver/ Transcoder Operator Guide Document No.: 548272-001 Home and Networks Mobility WARNING The unauthorized modification of any transcoder and the sale and use of any
More informationConfiguring Satellite RFSD-2XA For RF Signal Monitoring
Configuring Satellite RFSD-2XA For RF Signal Monitoring 1. Set your Options a. From Monitoring Menu screen, select Monitor Setup and press Enter. b. From Monitor Setup menu screen, select Options, and
More informationMotorola DSR-6000 Commercial Integrated Receiver/Decoder Operator Guide
Motorola DSR-6000 Commercial Integrated Receiver/Decoder Operator Guide STATUS Document No.: 557526-001 WARNING The unauthorized modification of any decoder and the sale and use of any such decoder is
More informationDigiPoints Volume 2. Student Workbook. Module 5 Headend Digital Video Processing
Headend Digital Video Processing Page 5.1 DigiPoints Volume 2 Module 5 Headend Digital Video Processing Summary In this module, students learn engineering theory and operational information about Headend
More informationDataSAT ACU-2 Controller Wiring Configuration - Operation
DataSAT ACU-2 Controller Wiring Configuration - Operation This manual covers basic wiring, antenna controller configurations, and typical operation. For proper operation, wiring and configuration are very
More informationRF Mogul. Quick Start. Model: SDC1. Satellite Dish Controller
RF Mogul Satellite Dish Controller Model: SDC1 Quick Start 29 February 2012 Minimum required hardware to find a Satellite! This Quick Start document is for connecting and operating a General Dynamics C125M
More informationProfessional Media Server Quick Start Guide
ipump 6400 Professional Media Server Quick Start Guide Figure 4. ipump Web Interface Status Page 6. Shut down your ipump from the front panel. Navigate from the home screen to the Shutdown screen as follows:
More informationPathfire Dish Repoint from Galaxy 26 Vertical (93º WL) to Galaxy 25 Vertical (97º WL) CWD Rev /30/2008
Shortly after 11AM ET on 6/29/2008, the Galaxy 26 satellite used for distribution of syndicated programming using Pathfire from CBS Worldwide Distribution and Disney ABC Domestic Television Distribution
More informationIMPORTANT QUESTIONS AND ANSWERS REGARDING TBN'S TRANSITION FROM ANALOG TO DIGITAL ON GALAXY 14. Facts at a Glance: TBN change from Analog to Digital
IMPORTANT QUESTIONS AND ANSWERS REGARDING TBN'S TRANSITION FROM ANALOG TO DIGITAL ON GALAXY 14 Facts at a Glance: TBN change from Analog to Digital Current TBN analog signal: Galaxy 14 Transponder 3 New
More informationSAT IF distribution system
7. Technical specifications Type cs43 RF input frequency range pr. 50-350 MHz inputs number 4 level pr. 55...88 dbµv 60...93 dbµv symbol rate 3 45 Ms/s return loss/impedance > 0 db/75 Ω LNB powering/control
More informationDSR-7400 Series. Commercial Integrated Satellite Receiver/Transcoder. Highlights. Product Overview
DSR-7400 Series Commercial Integrated Satellite Receiver/Transcoder Highlights DSR-7412 provides 24 transcoded output services (12 HD and 12 down-converted SD) DSR-7401 transcodes and down-converts up
More informationOperation and Installation Guide
Operation and Installation Guide HDS2800 Series Encoder Modulator High Definition (HD) Digital COFDM MPEG2 and H.264 Modulator with IP Multicast. 19 Rack Mount Wall Mount Revision 0.1 Firmware version
More informationOperation and Installation Guide
Operation and Installation Guide HDS2800 Series Encoder Modulator High Definition (HD) Digital COFDM MPEG2 and H.264 Modulator with IP Multicast. 19 Rack Mount Revision 4.0 Firmware version Released File
More informationQRF5000 MDU ENCODER AND QAM MODULATOR
Radiant Communications Corporation 5001 Hadley Road South Plainfield NJ 07080 Tel (908) 757-7444 Fax (908) 757-8666 WWW.RCCFIBER.COM QRF5000 MDU ENCODER AND QAM MODULATOR Installation & Operational Manual
More informationCompactMax-2 DVB-S/S2 TO DVB-T2 TRANSMODULATOR - 0 MI2100 -
CompactMax-2 DVB-S/S2 TO DVB-T2 TRANSMODULATOR - 0 MI2100 - SAFETY NOTES Read the user s manual before using the equipment, mainly "SAFETY RULES" paragraph. The symbol on the equipment means "SEE USER
More informationQuick installation and configuration guide STC
Quick installation and configuration guide STC 200 REF. 4466 Contents 4 Introduction 4 General description 5 General use of the headend 6 Initial installation and configuration 6 Assembly, connection
More informationEdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY
EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY 493456301 Rev B April 2009 Table of Contents Installation... 1 Setup... 2 Operation... 4 Live Video... 4 Video Settings... 5 Network
More informationTable of Contents. 1. Safety Use. 2. General Description. 3. Connection Diagram. 4. Operations and Management. 4.1 Display Status. 4.
DTM-HD01 Thank you for buying this encoder modulator. Please read this manual carefully to install, use and maintain the encoder modulator in the best conditions of performance. Keep this manual for future
More informationXsarius Satmeter Pro. Manual
Xsarius Satmeter Pro Manual 1 2 Directory of content Introduction Directory of content 3 Introduction 3 Satmeter Pro 02 Frontpanel & buttons 6 Xsarius provides high quality products that enable you to
More informationSTORQ System Installation Guide
STORQ System Installation Guide 1 STORQ Installation 2014 Westwood One All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including
More informationHITS QT/QT+ Setup Instructions for QSD/QHD Services using: Drake SCT2x4 Headend Transcoder 2 Satellites/4 Multiplexes
HITS QT/QT+ Setup Instructions for QSD/QHD Services using: Drake SCT2x4 Headend Transcoder 2 Satellites/4 Multiplexes Drake Transcoder Front /Rear View Setup and Programming Instructions: Input Setup Below
More informationSZU OPERATING INSTRUCTIONS SAT NAVI
SZU 21-00 O P ER ATI N G I N S T R U C T I O N S SAT NAVI Operation Instructions SZU 21-00 Safety Notes Turn off the receiver or any used power supply before installing, to avoid short-circuit. Installation
More informationRC3000 User s Manual additions for the Positive Identification feature.
RC3000 User s Manual additions for the Positive Identification feature. 1.2 Software Configuration The positive identification feature requires the presence of three navigation sensors: 1) GPS receiver,
More informationEEG A1452 SCTE-104 Inserter Frame Card
EEG A1452 SCTE-104 Inserter Frame Card Product Manual EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright EEG Enterprises, Inc. 2017 All
More informationUser Manual. TCU/RCU RF Head Control Units. TCU/RCU Analogue 11/6/
11/6/2009 www.elber.com elber@elber.it TCU/RCU RF Head Control Units User Manual Elber s.r.l.- Via Pontevecchio, 42W Phone +39-0185.35.13.33 16042 Carasco (GE) Italy Fax +39-0185.35.13.00 1 Sommario 2
More informationDigital Tuner Streamer
Digital Tuner Streamer This Manual Apply to the MTRX 4/8 Tuner To IPTV Systems On 8 Tuners Systems, The inputs are all assigned to the 8 Tuners Only and no asi Web-NMS Version: 1.03 Software: 1.00 Hardware:
More informationFS1-X. Quick Start Guide. Overview. Frame Rate Conversion Option. Two Video Processors. Two Operating Modes
FS1-X Quick Start Guide Overview Matching up and synchronizing disparate video and audio formats is a critical part of any broadcast, mobile or post-production environment. Within its compact 1RU chassis,
More informationRDS: The RDS, or Radio Data System, is supported in the g! interface where available.
Manufacturer: Integra Integration Note Model Number(s): Integra 20.3/30.3/40.3/50.3/70.3/80.3 Core Module Version: 5.4 Comments: FW 1.09 (1091-0999-0210-9105) Document Revision Date: 1/15/2013 OVERVIEW
More informationHardware and software setup guide
Installation of a GEONETCast terminal Hardware and software setup guide Version: 18.05.2015 II Table of contents List of figures... III 1 Introduction... 1 2 Selection of hardware... 2 2.1 Parabolic antenna...
More informationN+1 Redundancy with the VCom HD4040 Upconverter
N+1 Redundancy with the VCom HD4040 Upconverter Document ID: 47164 Contents Introduction Prerequisites Requirements Components Used Conventions Set Up Communication with the Upconverter VCom Dual4040D
More informationAmb-OS Media, LLC AMR-100
Amb-OS Media, LLC AMR-100 Operations Manual Firmware 2.30 Revision 41 03/11/15 SUPPORT INFORMATION Email: support@amb-os.com Phone 877AMBOS2U (877) 262-6728 AMB-OS WEB PAGE for program downloads, RSS feed
More informationBELAR FMHD-1 PRECISION DIGITAL FM HD MONITOR/ANALYZER. Guide to Operations 2011/06/22
BELAR FMHD-1 PRECISION DIGITAL FM HD MONITOR/ANALYZER Guide to Operations 2011/06/22 2011 BELAR ELECTRONICS LABORATORY, INC. 119 LANCASTER AVENUE P.O. BOX 76 DEVON, PA 19333-0076 USA VOICE (610) 687-5550
More informationAPM CALIBRATION PROCEDURE Rev. A June 3, 2015
APM CALIBRATION PROCEDURE Rev. A June 3, 2015 Calibration of the APM allows system parameters such as coupler coupling values, interconnecting cable losses and system feeder losses to be programmed into
More informationATLANTA ASF 2033HD+ DVB-S/S2 METER. User`s Manual
ATLANTA ASF 2033HD+ DVB-S/S2 METER User`s Manual Buttons and Indicators... 2 How to measure... 3 Main menu... 4 LNB Setting... 4 Edit Satellite... 6 Spectrum Chart... 7 Constellation... 9 Angle Calculation...
More informationCompactMax-4 DVB-S/S2 TO ISDB-T TRANSMODULATOR - 0 MI2101 -
CompactMax-4 DVB-S/S2 TO ISDB-T TRANSMODULATOR - 0 MI2101 - SAFETY NOTES Read the user s manual before using the equipment, mainly "SAFETY RULES" paragraph. The symbol on the equipment means "SEE USER
More informationTechnical Manual August 2014
Technical Manual Quick Reference... 3 Important Information... 4 Quick Set Up Guide... 5 Program and Data Delivery by Satellite... 6 IDC Receiver Installation Guide... 7 Introduction... 7 Antenna Requirements...
More informationUsers Manual Firmware 2.03 September 6, 2017
Users Manual Firmware 2.03 September 6, 2017 Proton Switcher Control Surface and Ion Switcher Control Surface are trademarks of JLCooper Electronics. All other brand names are the property of their respective
More informationInstallation & Operational Manual
Radiant Communications Corporation 5001 Hadley Road South Plainfield NJ 07080 Tel (908) 757-7444 Fax (908) 757-8666 WWW.RCCFIBER.COM QRF5000M MDU ENCODER Installation & Operational Manual Rev.A2 1. Introduction
More informationUPCOM UC-250L L-BAND DVB MODULATOR
UPCOM UC-250L L-BAND DVB MODULATOR OPERATIONS MANUAL UPCOM TECHNOLOGIES INC. SAN JOSE, CA - USA 2007 Operations Manual UC-250L 2007 UPCOM TECHNOLOGIES, INC This document is property of UPCOM TECHNOLOGIES,
More informationSIG7710 QPSK - DVB-IP STREAMER
QPSK - DVB- STREAMER ISTRUZIONI PER L USO OPERATING INSTRUCTIONS INSTRUCTIONS D EMPLOI INSTRUCCIONES DE USO INSTRUÇÕES DE FUNCIONAMENTO BETRIEBSANLEITUNG 1. SAFETY WARNINGS The product must be installed
More informationUsers Manual Firmware 3.03 May 9, 2018
Users Manual Firmware 3.03 May 9, 2018 Proton Switcher Control Surface and Ion Switcher Control Surface are trademarks of JLCooper Electronics. All other brand names are the property of their respective
More informationZ-IP Stream 004/008. User Guide and Installation Manual. Four or Eight Input QAM Encoder / Modulator
Z-IP Stream 004/008 User Guide and Installation Manual Four or Eight Input QAM Encoder / Modulator MPEG-2 / H.264 HD ENCODER with QAM /IP/ & ASI Outputs Contents Safety Precautions... 3 Package Contents...
More informationRAINIERCISCOCOMMERCIALD9865 D - H - B RECEIVERQUICKTIPS.
RAINIERCISCOCOMMERCIALD9865 D - H - B RECEIVERQUICKTIPS. PLEASE READ DOCUMENT FULLY BEFORE ATTEMPTING TO PROGRAM DATA. Pre-setup Procedure Connect with RG6u 1450 mhz or better jumper cable using compression
More informationOSD. EXECUTIVE / MiniDome USERS MANUAL. USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD
EXECUTIVE / MiniDome OSD USERS MANUAL USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD MotoSAT Corporation Created April 22, 2003 1-800-247-7486 CONGRATULATIONS! on your purchase of your
More informationFS3. Quick Start Guide. Overview. FS3 Control
FS3 Quick Start Guide Overview The new FS3 combines AJA's industry-proven frame synchronization with high-quality 4K up-conversion technology to seamlessly integrate SD and HD signals into 4K workflows.
More informationPCM-1210 DVB COMBO METER User`s Manual
PCM-1210 DVB COMBO METER User`s Manual 1. Main Features... 1 2. Buttons and Indicators... 2 3. How to measure... 3 4. Home menu... 4 5. Satellite... 4 5.1 Satellite Measure... 4 5.2 LNB Setting... 5 5.3
More informationHorizon HD-STM. Combo Signal Analyzer TEST REPORT
TEST REPORT Combo Signal Analyzer Horizon HD-STM can be used intuitively, manual is not needed perfect workmanship optimized for the day-to-day work of an installer gives all the "Must-Have" informations
More informationSNG-2150C User s Guide
SNG-2150C User s Guide Avcom of Virginia SNG-2150C User s Guide 7730 Whitepine Road Revision 001 Richmond, VA 23237 USA GENERAL SAFETY If one or more components of your earth station are connected to 120
More informationAVE HOME FAGOR CVBS TO DVB-T ENCODER MODULATOR. Fagor Electr6nica
AVE HOME CVBS TO DVB-T ENCODER MODULATOR FAGOR Fagor Electr6nica TABLE OF CONTENTS 1. SPECIFICATIONS... 12 1.1 Product Overview... 12 1.2 Appearance and Description... 12 1.3 Diagram... 13 1.4 Characteristics...
More informationProfessional HD Integrated Receiver Decoder
Professional HD Integrated Receiver Decoder User Manual V1.00-C Preface About This Manual This manual provides introductions to users about how to operate the device correctly. The content includes introduction
More informationSQTR-2M ADS-B Squitter Generator
SQTR-2M ADS-B Squitter Generator Operators Manual REVISION A B C D E F G H J K L M N P R S T U V W X Y Z December 2011 KLJ Instruments 15385 S. 169 Highway Olathe, KS 66062 www.kljinstruments.com NOTICE:
More information16 channels transmodulator S2C16
16 channels transmodulator S2C16 Vers. 1.01 USER S MANUAL S2C16 - SAT to QAM transmodulator 1. Product description S2C16 is a 16 channel transmodulator with DVB-S/S2 input and DVB-C output. It has 4 main
More informationDigital CATV Head End Modular Bank
Digital CATV Head End Modular Bank User Manual (ver. A) http://www.pbi-china.com 目录 1. SUMMARY...1 2. BASIC OPERATION ON HDMS...2 2.1 Minimum requirements for PC...2 2.2 Installation...2 2.3 Edit IP addresses
More informationQAM HD Integrated Receiver Decoder with SDI/HDMI/ASI/IP Signal Outputs. User Manual B-IRD-HD-PRO-Q HD IRD
QAM HD Integrated Receiver Decoder with SDI/HDMI/ASI/IP Signal Outputs User Manual B-IRD-HD-PRO-Q HD IRD DIRECTORY Chapter 1 Product Outline... 1 1.1 Outline... 1 1.2 Features... 1 1.3 Specifications...
More informationSTM 17 HD. DVB-S2+T2/C Compact Meter. User Manual. Ref R13. CAHORS Digital CS Cahors Cedex 9 FRANCE.
STM 17 HD DVB-S2+T2/C Compact Meter User Manual Ref 0145131R13 DVB COMBO METER 1. Main Features... 2 2. Buttons and Indicators... 3 3. How to measure... 4 4. Home menu... 5 5. Satellite... 5 5.1 Satellite
More informationOwner s Manual. Sat-Meter MSK 15. Order No.:
Owner s Manual Sat-Meter MSK 15 Order No.: 217 100 13 Thank you for choosing our latest and most innovative satellite meter. It has been designed and manufactured to a very high standard and offers a UNIQUE
More informationASF 2050 COMBO USER MANUAL
ASF 2050 COMBO USER ASF 2050 COMBO USER 1. BUTTONS AND INDICATORS... 2 2. BASIC FUNCTIONS.... 4 2.1 Satellite... 5 2.2Terrestrial... 24 2.3 Cable... 33 2.4 Saving... 41 2.5 System Setting... 42 2.6 USB
More informationMyM-3S Micro Master. Installation Guide. English. design for TV
MyM-3S Micro Master Installation Guide design for TV 1 CONTENT 1. Introduction 2. Unpacking the unit 3. Connections and indications 4. IP settings 5. Menus and settings 5.1 Overview menu 5.2 Input settings
More informationDigiPoints Volume 2. Leader Guide. Module 5 Headend Digital Video Processing
Headend Digital Video Processing Page 5.i DigiPoints Volume 2 Module 5 Headend Digital Video Processing Summary In this module, students will learn engineering theory and operational information about
More informationTHE UNIVERSAL RF INSTALLATION GUIDE
THE UNIVERSAL RF INSTALLATION GUIDE Released in January 2010 By: AFSAT SERVICES LIMITED AIS HANGAR, WILSON AIRPORT, LANGATA ROAD P.O. BOX 27554, 00506 NAIROBI, KENYA. www.iwayafrica.com 1 Abbreviations
More informationXR-3 QAM 8VSB. Modular Test Instrument. XR-3 Rugged Adaptable Economically Efficient Configurable to test: and more
XR-3 Modular Test Instrument XR-3 Rugged Adaptable Economically Efficient Configurable to test: and more QAM 8VSB XR-3 Modular Test Instrument GENERAL FEATURES Durable case with rubber shock guards Color
More informationM5-H002. Multiview T-35. DVB-T to PAL / 5 channels on all TV s
120531 M5-H002 Multiview T-35 DVB-T to PAL / 5 channels on all TV s Contents Multiview... 3 Features... 3 Caution... 3 Front & Rear Panel... 4 Connecting... 5 Programming... 6 Information... 7 Installation...8
More informationSATELLITE FINDER SK-3200 USER MANUAL
SATELLITE FINDER SK-3200 USER MANUAL CONTENTS 1. GUIDE...1 1.1 IMPORTANT SAFETY INSTRUCTIONS... 1 1.2 UNPACKING...1 1.3 PRODUCT OVERVIEW & ILLUSTRATION... 2 2. OUTLINE...4 3. THE MENU OSD INSTRUCTION...5
More informationUser Instruction Manual IQDBT105. DVB-T/T2 Terrestrial Receiver & Monitor.
User Instruction Manual IQDBT105 DVB-T/T2 Terrestrial Receiver & Monitor www.s-a-m.com Information and Notices Information and Notices Copyright and Disclaimer Copyright protection claimed includes all
More informationSetup Guide. Flanders Scientific BoxIO. Rev. 1.1
Setup Guide Flanders Scientific BoxIO Rev. 1.1 Introduction CalMAN Required Version CalMAN takes advantage of the features of the Flanders Scientific BoxIO advanced color management device to calibrate
More informationHD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L
HD4112 Quad HDMI MPEG2 HD DVBT Encoder Modulator U S E R M A N U A L HD4112 Manual Rev 1 Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1
More informationReceiver Integration Note
ELAN Home Systems Life Just Got Better Receiver Integration Note Manufacturer: Model Number(s): Controller Core Module: Denon Document Revision Date: 1/30/2012 OVERVIEW AND SUPPORTED FEATURES AVR-1912,
More informationSatellite locator WS-6933
R Satellite locator WS-6933 User's Manual English CONTENTS 1. GUIDE...2 1.1 IMPORTANT SAFETY INSTRUCTIONS...2 1.2 UNPACKING...2 1.3 PRODUCT OVERVIEW&ILLUSTRATION...3 2. OUTLINE...4 3. THE MENU OSD INSTRUCTION...5
More informationRF Mogul. Operation Manual. MotoSAT J1/D4 Controllers. Firmware Upgrade for
RF Mogul Firmware Upgrade for MotoSAT J1/D4 Controllers Operation Manual Version 14.01 13 April 2014 Index SDC1 Satellite Dish Controller Features 1 Getting Started 2 Quick Setup 2 Front Panel Operation
More informationUsers Manual Firmware 1.06 October 12, 2016
Users Manual Firmware 1.06 October 12, 2016 Proton Switcher Control Surface is a trademark of JLCooper Electronics. All other brand names are the property of their respective owners. Proton Switcher Control
More informationFour-way Return Optical Receiver Manual. Transmitter OP-OR124RJ. Shenzhen Optostar Optoelectronics Co., Ltd (Version 1)
Four-way Return Optical Receiver Manual Transmitter OP-OR124RJ Shenzhen Optostar Optoelectronics Co., Ltd 2016. 7(Version 1) 1. Summary OP-OR124RJ type is the upgrade product of OP-OR124R type. Can automatically
More informationSimple Media Platform Quick Installation Guide V1.0-N. Simple Media Platform. Quick Installation Guide
Simple Media Platform Quick Installation Guide 1. Installation Instruction 1.1 Mounting unit to a 19 rack When selecting the installation site, try to comply with the following: Protective Ground - The
More informationuser manual Colosseum 8500D
user manual Colosseum 8500D No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without permission. Unitron reserves the right to change the specifications
More informationPortable TV Meter (LCD) USER S MANUAL
1 Portable TV Meter User Manual (LCD) Portable TV Meter (LCD) USER S MANUAL www.kvarta.net 1 / 19 2 Portable TV Meter User Manual (LCD) Contents 1. INTRODUCTION... 3 1.1. About KVARTA... 3 1.2. About DVB...
More informationSetup Guide. Dolby PRM Rev. 1.1
Setup Guide Dolby PRM-4200 Rev. 1.1 Introduction CalMAN Required Software Version CalMAN Display Calibration Software can automatically create an optimized 3D calibration LUT for the Dolby PRM-4200 monitor.
More informationXDS-PRO Satellite Receivers
User s Guide XDS-PRO SERIES (PRO1Q, PRO4Q, PRO1R, PRO4R) Visit Our Website www.picodigital.com Contact Us 858.546.5050 Toll Free 858.421.6511 Important Notices Copyright 2017 Pico Digital, Inc. All rights
More informationDVISm. DVISm - Mini Digital Video Insertion System. Quick Start Guide. Patent Pending
DVISm Patent Pending DVISm - Mini Digital Video Insertion System Quick Start Guide Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice, to make
More informationDATUM SYSTEMS Appendix A
DATUM SYSTEMS Appendix A Datum Systems PSM-4900 Satellite Modem Technical Specification PSM-4900, 4900H and 4900L VSAT / SCPC - Modem Specification Revision History Rev 1.0 6-10-2000 Preliminary Release.
More informationUser Manual. UNIVERSE Ref. 8600
User Manual UNIVERSE Ref. 8600 No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without permission. Unitron reserves the right to change the specifications
More informationC Module Description
ASI Distribution Amplifier with Signal Inversion C Module Description The is an ASI distribution amplifier with up to 8 outputs in double width or 4 outputs in single width. The input is transformer coupled
More informationOMNISTAR GX2. GX2-LM1000E Series 1310 nm Broadcast Transmitter DATA SHEET BENEFITS. 1 GHz bandwidth
DATA SHEET BENEFITS OMNISTAR GX2 GX2-LM1000E Series 1310 nm Broadcast Transmitter 1 GHz bandwidth High module density up to 16 transmitter modules in a 4 RU housing High performance: Advanced predistortion
More informationSuper Buddy Operation Manual
Operation Manual Revision 2.00 Date 10/23/2007 1. INTRODUCTION...4 CONNECTIONS... 4 IRD CONNECTION... 5 PC CONNECTION... 5 2. RUN SCREEN...5 DISPLAYED DATA... 5 SOFT KEYS... 6 CHANGING SATELLITES... 6
More informationProfessional 8-in-1 TS Processor MX5308 USER MANUAL 2015/06
Professional 8-in-1 TS Processor MX5308 USER MANUAL 2015/06 MX5308 8-in-1 TS Processor License Declaration Without the prior written permission of ANTIK Technology, no part of this manual shall be added
More informationSPG700 Multiformat Reference Sync Generator Release Notes
xx ZZZ SPG700 Multiformat Reference Sync Generator Release Notes This document supports firmware version 3.0. www.tek.com *P077123104* 077-1231-04 Copyright Tektronix. All rights reserved. Licensed software
More informationREMOTE DISPLAY WIRELESS DECODER MK II
REMOTE DISPLAY WIRELESS DECODER MK II INSTALLATION MANUAL Part No. LED-DEC 1. Contents 1. Contents... 1 2. Equipment List... 2 3. Overview... 2 Introduction... 2 Location Selection **Important **... 2
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES
Manufacturer: Model Number(s): Minimum Core Module Version: Document Revision Date: Denon Integration Note AVR-2805, 3805, 1613, 1713, 1912CI, 1913, 2112CI, 2113CI, 2310CI, 2311CI, 2312CI, 2313CI, 2808CI,
More informationLong Distance L-Band Fiber Optic Links
Long Distance L-Band Fiber Optic Links Product Description Features & Benefits L-Band: 950 3000MHz Transmission distance up to 100Km Optimized version for Uplink and Downlink applications Powerful management
More informationUser s Manual HDMI Modulator ATSC 8VSB/QAM 65/256. Model No : HDM100
User s Manual HDMI Modulator ATSC 8VSB/QAM 65/256 Model No : HDM100 Contents 1. Safety Instructions & Precautions. 1 2. Operation Guide.. 2 2-1. Connection Diagram. 2 2-2. Front Panel.... 3 2-3. Rear Panel.....
More informationAUTOPILOT DLM Satellite Downlink Manager USER GUIDE
AUTOPILOT DLM Satellite Downlink Manager USER GUIDE AUTOPILOT User Guide Rev 3.70 Nov. 2004. Broadcast Automation Systems, Inc. 35 Sunnypoint Crescent, Scarborough, ON, Canada M1M 1B8 tel: 416-264-8415
More informationHD168Bi Quad CVBS/HDMI HD DVBT Encoder Modulator U S E R M A N U A L
HD168Bi Quad CVBS/HDMI HD DVBT Encoder Modulator U S E R M A N U A L Contents 1. GENERAL 1.1 Description 1.2 Specifications 2. INSTALLATION 2.1 What s in the Box 2.2 Connection 2.2.1 DEVICE Programming
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version October 5, 2016 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE TERMINAL...6
More informationGetting Started Guide
MaxEye Digital Video Signal Analysis Toolkit DVB-S Version 1.0 Getting Started Guide Contents 1. Introduction... 3 2. Installed File Location... 3 3. Programming Examples... 3 3.1. Measure Modulation Accuracy...
More informationRFSD-2XA RF Signal Monitor Operation Manual
RF Signal Monitor This manual covers basic operations and functions of the RFSD-2XA RF Signal Monitor. For more detailed instructions on how to use the instrument for different applications, see the Application
More informationUser Manual. UNIVERSE Ref. 8600
User Manual UNIVERSE Ref. 8600 No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without permission. Unitron reserves the right to change the specifications
More informationBonding. Black Ground Wire Indicates # 17ga CCS Bond. Green Bonding Wire Indicates # 10ga Solid Copper. External Wall
SWiM Integrated LNB Installation KaKu - HD DVR SWiM compatible Single tuner SWiM compatible 4 way single port DC power passing splitter rated from 2-2150MHz BBC s are not required in this scenario Weather
More informationDCD-24 Word Clock Distributor
DCD-24 Word Clock Distributor Owner s manual Version 1.00 October 2018 All materials herein Brainstorm Electronics, Inc. Brainstorm Electronics reserves the right to change or modify the contents of this
More informationL-Band Fiber Optic Links
L-Band Fiber Optic Links Features & Benefits L-Band: 950 3000MHz Up to 10Km distance Wide input power suitable for both Uplink and Downlink applications Powerful management capabilities via a front panel
More informationipump 562 Digital Media Server Quick Start Guide
ipump 562 Digital Media Server Quick Start Guide. General Information The WEGENER ipump 562 is a digital media server capable of decoding satellite signals or IP streams or playing stored content from
More informationUnity 552. Digital Media Receiver Installation Quick Start Guide
Unity 552 Digital Media Receiver Installation Quick Start Guide. General Information The WEGENER Unity 552 is a digital satellite receiver, compliant with DVB S2 modulation supporting QPSK and 8PSK formats.
More information