Digital Fiber Sensor FX-300 SERIES. Constant advances achieving significant improvement of sensing performance

Transcription

1 19 Digital SERIES General terms and conditions... P.1 Related Information FX-CH2 / SC-GU P.199 / P.201 ~ Korea s S-mark... P.104~ Sensor selection guide P.11~ / P.61~ Glossary of terms / General precautions... P.98 ~ / P.986 ~ PHOTO PHOTO Conforming to EMC Directive Certified NPN output types of connector type only UL Recognition The digital fi ber sensor FX-01(P) has been modifi ed since its production in June Refer to p.154~ for details. PNP output type available Timer Interference prevention Light intensity monitor MEASURE SUNX website Constant advances achieving significant improvement of sensing performance Automatic sensitivity setting Stable sensing over long and short periods FX-01 FX-01-HS FX-05 Even greater sensing range All models In addition to a four-chemical emitting element which suppresses changes in the light emitting element over time so that a stable level of light emission can be maintained over long periods, a APC (Auto Power Control) circuit has also been adopted afreshly. The light emitting amount can be controlled in minute degrees so that even changes occurring over very short periods can be handled, allowing stable sensing performance by suppressing deviations in light emitting amounts caused by changes in the ambient environment that could not previously be suppressed. Stable sensing comparison Light emitting amount Short-term stability Deviation Adoption of a double coupling lens that increases emission effi ciency to its maximum limits and greatly increases sensing range. Sensing ranges with small diameter fi bers and ultra-small diameter fi bers, which have become very popular due to the miniaturization of chip components, have been increased by 50 % over previous values achieved with other amplifi ers. Conventional fiber sensors (Without lens) Double coupling lens Disperses the light reduces emitting efficiency. Long-term stability Time FX-01 FX-01-HS FX-05 Three-chemical emitting element, Without APC The lens concentrates the light, greatly increasing emitting efficiency.

2 ORDER GUIDE P.14 ~ LIST OF S P.145 ~ SPECIFICATIONS P.151 I/O CIRCUIT DIAGRAMS P.152 SENSING CHARACTERISTICS P.15 ~ Digital SERIES 140 PRECAUTIONS FOR PROPER P.15 ~ DIMENSIONS P.156 APPLICATIONS Detecting the presence or absence of labels The light-emitting amount selection function can even stabilize detection of transparent labels that saturate the light-receiving level. Detecting the presence or absence of ICs on a tray You can set upper and lower limits for the threshold values using the window comparator mode and turn ON / OFF the incident light intensity within that limit. Detecting the passage of small objects The differential sensing mode will only detect rapid changes in the amount of light, which makes it possible for small objects to be detected. PHOTO PHOTO Light-emitting amount selection FX-01 FX-01-HS FX-05 If the light receiving level becomes saturated during close-range sensing or when sensing transparent or minute objects, you can adjust the light emitting amount of the sensor to stabilize sensing without needing to change the response time. Sensing that previously required the response time or fi bers to be changed can now be set much more easily using this function. [Light receiving level saturated] [Stable sensing] Actual digit difference: C A Upper display limit 4000 Actual digit difference: C Light emitting amount A, B changed Saturated digit B, difference: D Level 4 Level Level 2 Level 1 OFF Light emitting amount can be changed without changing response time MEASURE Large display 9999 FX-05 Large display with 4 digits (9999). With a greater difference in digit value than previous models, threshold values can be set in units of 1 digit up to maximum Threshold setting can now be done more easily and accurately. (During STDF, LONG and U-LG modes) 2.5 times previous models Digit difference comparison Example Digit difference between object A and object B Previous models 4000 FX Ultra high-speed 5 μs response FX-01-HS Ultra high-speed 5 μs response. Even small objects moving at high speeds can be sensed. In addition, at 65 μs the FX-01 standard type is also twice as fast as previous models. Ultra high-speed type FX-01-HS (H-SP mode) 5 μs Standard type FX-01, High-function type FX-05 (H-SP mode) 65 μs 4 times as fast as before 5 μs Digit difference: Small Digit difference: Large Previous model 150 μs

3 141 Digital SERIES PHOTO PHOTO Simplified systems using new operating modes A window comparator mode and differential sensing mode have been added. These modes make it easy to carry out sensing tasks that previously required multiple sensors or involved complex threshold settings. Window comparator mode <Sensing ICs in trays> Differential sensing mode <Sensing of tiny moving objects> FX-05 MEASURE Tray absent IC present Tray present OFF ON OFF Incident light intensity Upper and lower limits for threshold values can be set so that the incident light intensity can turn on and off within those ranges. Single output is used, so that only one cable is required, and no PLC processing is required either. Incident light intensity Lower light amounts due to dust Because sensing is not possible at normal sensitivity settings, sensitivity must be reset. ON ON Sensing of only sudden changes in light amounts Only the target objects are sensed. No need to reset the sensitivity. Equipped with 5 types timers FX-05 The FX-05 includes the same ON-delay / OFF-delay / ONE SHOT timer as the FX-01(-HS), as well as an ON-delay OFF-delay timer and an ON-delay ONE SHOT timer. A wide variety of timer control operations can be carried out by these fi ber sensors alone. Timer period Output 1: 0.5 to 9,999 ms (variable) Output 2: 0.5 to 500 ms (variable) Time chart Sensing condition ON-delay OFF-delay For L-ON T1 T1 T1 Beamreceived Beaminterrupted ON OFF ON OFF Even beginners can quickly learn how to use the MODE NAVI MODE NAVI uses six indicators to display the amplifi er s basic operations. The current operating mode can be confi rmed at a glance, so even a fi rst time user can easily operate the amplifi er without becoming confused. RUN TEACH ADJ RUN TEACH ADJ RUN TEACH ADJ RUN This is the sensing mode. Incident light level is displayed in the digital display. TEACH This mode is for setting the threshold value. ADJ In this mode, the threshold value, once set, may be fine-tuned. ONE SHOT ON-delay OFF-delay ON-delay ONE SHOT T1 T1 T1 T1 T2 T2 ON OFF ON OFF ON OFF All models L/D L / D ON TIMER This mode allows the selection of output operation as either PRO Light-ON or Dark-ON. L/D TIMER TIMER This mode permits the choice of using or not PRO using the timer. L/D PRO TIMER This mode allows the selection of further advanced functions, such as the copying of PRO individual settings and the memory functions. Easy confirming of threshold value settings FX-01 FX-01-HS FX-05 The threshold value can be confi rmed by turning the jog switch even during RUN mode. Jog switch is turned Left: FX-01(-HS) Output 1 for FX-05 Right: Output 2 for FX-05 The threshold value is displayed

4 Digital SERIES 142 The use of only two switches makes for very simple operations Only two switches, the large jog switch and the large MODE key, are required for operation. You can operate it simply by the steps shown on the right. Large MODE key Pressing the switch selects or cancels the operating mode A quick-connection cable saves wiring and work-hours FX-01/B/G/H FX-01-HS FX-05 One unit can be used as either a main unit or sub unit The amplifi er unit can be used as either a main unit or a sub unit. This feature allows for easy mounting in the side-by-side confi guration. The main and sub unit functions are distinguished only by the proper use of the main cable and the sub cable. Moreover, inventory management and maintenance is simplifi ed. FX-05 FX-01(-HS) FX-01B/G/H Main cable (4-core) CN-74-C Sub cable (2-core) CN-72-C Main cable (-core) CN-7-C Sub cable (1-core) CN-71-C 1 Identical part numbers eliminate the need for costly inventory management labor Main cable Sub cable Large jog switch 2 Moving the switch from side to side allows items to be selected All models Pressing the switch then confirms the selected setting An optical communication function allows up to *16 sensors to be adjusted simultaneously FX-01 FX-05 The optical communication function allows the data that is currently set to be copied and saved all at once for all amplifiers connected together from the right side. This greatly reduces troublesome setup tasks and makes setup much smoother.in addition, troublesome adjustment operations at times such as when replacing sensors can also be carried out easily and data can also be copied and stored Single copy & save operation for all amplifiers using the optical communication function. * Use the optical communication function for only the same types of sensors. Furthermore, the FX-01-HS is not equipped with optical communication function capability. Settings can be entered directly using numerical input All models Every function can be directly set merely by the input of a four digit code (numbers) from the code table. This convenient feature is easy to set up. In the event that settings are accidentally changed at the operating site, merely entering the correct code can restore the original settings. This results in easy and quick maintenance. Communication unit improves equipment starting up and maintenance External input unit for digital sensor FX-CH2 Teaching and changing settings can be performed by using the PLC and touch panel. Various settings and switching of up to 16 units of digital fi ber sensors can be accomplished at once without operating the actual sensors themselves, but via external signals, such as the PLC, touch panel, and push buttons. <Main functions> Batch teaching. Key lock setting Batch loading / saving of the data bank. Upstream communication unit for digital sensor First digit: Settings for response time and hysteresis Second digit: Settings for L/D ON and display mode Fourth digit: Timer period settings Third digit: Settings for Adjust lock and timer SC-GU1-485 We now offer remote maintenance for digital sensors! The communication unit enables inputs to the digital fiber sensors (such as teaching and data bank switching) to be carried out via a PLC or a personal computer, and also allows confirming of the incident light intensity an output status for the fiber sensors. This greatly improves workability during equipment starting up and maintenance. <Communicable commands> Sensor incident light intensity Sensor settings verifi cation Sensor output status Threshold value settings, etc. FX-01 FX-05 FX-01(P) FX-05(P) PHOTO PHOTO MEASURE PLC Refer to p.199 for details Compatible with all PLCs equipped with RS-485 compatible units Refer to p.201 ~ for details RS-485 SC-GU1-485 communication

5 14 Digital SERIES ORDER GUIDE Quick-connection cable is not supplied with the amplifi er. Please order it separately. Type Appearance Model No. Emitting element Output Standard type High-speed type FX-01 FX-01P FX-01B FX-01BP FX-01G FX-01GP FX-01H FX-01HP FX-01-HS FX-01P-HS Red LED Blue LED Green LED Infrared LED Red LED NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor Quick-connection cables Type Model No. Length CN-7-C1 1 m.281 ft Sub cable (1-core) Main cable (-core) CN-7-C2 2 m ft CN-7-C5 5 m ft CN-71-C1 1 m.281 ft CN-71-C2 2 m ft CN-71-C5 5 m ft High-function type FX-05 FX-05P Red LED NPN open-collector transistor PNP open-collector transistor Main cable (4-core) Sub cable (2-core) CN-74-C1 CN-74-C2 CN-74-C5 CN-72-C1 CN-72-C2 CN-72-C5 1 m.281 ft 2 m ft 5 m ft 1 m.281 ft 2 m ft 5 m ft

6 Digital SERIES 144 ORDER GUIDE Quick-connection cables For FX-01(-HS)/B/G/H Quick-connection cable is not supplied with the amplifier. Please order it separately. Main cable Type Model No. Description Main cable (-core) Sub cable (1-core) CN-7-C1 CN-7-C2 CN-7-C5 CN-71-C1 CN-71-C2 CN-71-C5 Length: 1 m.281 ft Length: 2 m ft Length: 5 m ft Length: 1 m.281 ft Length: 2 m ft Length: 5 m ft 0.15 mm 2 -core cabtyre cable, with connector on one end Cable outer diameter: ø.0 mm ø0.118 in 0.15 mm 2 1-core cabtyre cable, with connector on one end Cable outer diameter: ø.0 mm ø0.118 in CN-7-C Sub cable CN-71-C For FX-05 Quick-connection cable is not supplied with the amplifi er. Please order it separately. Type Model No. Description Main cable (4-core) Sub cable (2-core) CN-74-C1 CN-74-C2 CN-74-C5 CN-72-C1 CN-72-C2 CN-72-C5 Length: 1 m.281 ft Length: 2 m ft Length: 5 m ft Length: 1 m.281 ft Length: 2 m ft Length: 5 m ft 0.15 mm 2 4-core cabtyre cable, with connector on one end Cable outer diameter: ø.0 mm ø0.118 in 0.15 mm 2 2-core cabtyre cable, with connector on one end Cable outer diameter: ø.0 mm ø0.118 in Main cable CN-74-C Sub cable CN-72-C End plates End plates are not supplied with the amplifi er. Please order them separately when the amplifi ers are mounted in cascade. Appearance Model No. Description MS-DIN-E When cascading multiple amplifi ers, or when it moves depending on the way it is installed on a DIN rail, these end plates clamp amplifi ers into place on both sides. Make sure to use end plates when cascading multiple amplifi ers together. Two pcs. per set Designation Model No. Description Amplifier mounting bracket Fiber amplifi er protection seal MS-DIN-2 FX-MB1 Mounting bracket for amplifi er 10 sets of 2 communication window seals and 1 connector seal Communication window seal: It prevents malfunction due to transmission signal from another amplifi er, as well as, prevents effect on another amplifi er. Connector seal: It prevents contact of any metal, etc., with the pins of the quickconnection cable. Note: Fiber amplifi er protection seals are supplied with the FX-01(P) and FX-05(P). Amplifier mounting bracket MS-DIN-2 Fiber amplifier protection seal FX-MB1 Communication window seal Connector seal

7 145 Digital SERIES LIST OF S FX-05 / FX-01 (Red LED type) sensing range (Note 1) Thru-beam type (one pair set) are listed in alphabetic order. Refer to p.6~ Fiber for details of each fi ber. Model No. The FX-05 and FX-01(-HS) have different sensing modes. FX-05: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-01(-HS): S-D, H-SP, FAST, STD, LONG (no STDF or U-LG mode) Sensing range (mm in) (Note 2) Red LED U-LG LONG STDF STD FAST H-SP S-D Dimensions FT-A8, (Note ), (Note ), , , , P.106 FT-A0, (Note ), (Note ), (Note ), (Note ), (Note ), , (Note ) P.106 FT-AFM P.106 FT-AFM2E P.106 FT-B8 1, , P.106 FT-E P.106 FT-E P.106 FT-FM2 1, P.106 FT-FM2S 1, P.106 FT-FM2S4 1, P.106 FT-FM10L 19, , , , , , , P.106 FT-H1-FM2 1, P.106 FT-H20-J20-S (Note 4) P.107 FT-H20-J0-S (Note 4) P.107 FT-H20-J50-S (Note 4) P.107 FT-H20-M P.107 FT-H20-VJ50-S (Note 4) P.107 FT-H20-VJ80-S (Note 4) P.107 FT-H20W-M P.107 FT-H0-M1V-S (Note 5) P.107 FT-H5-M P.107 FT-H5-M2S P.107 FT-HL80Y, , , , P.107 FT-K8, , , , P.108 FT-KV P.108 FT-KV8, , , , P.108 FT-L80Y, , , , , P.108 FT-NFM P.108 FT-NFM2S P.108 FT-NFM2S P.108 FT-P P.108 FT-P P.108 FT-P P.108 FT-P P.108 FT-P81X P.108 FT-PS P.109 Notes: 1) Refer to p.76 for the sensing ranges for the FX-01-HS in H-SP mode and for the FX-01B/G/H. 2) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut. ) The fi ber cable length practically limits the sensing range to,500 mm in long. 4) Heat-resistant joint fi bers and ordinary-temperature fi bers (FT-FM2) are sold as a set. Please refer to p.9~ for details. 5) Sold as a set comprising vacuum type fi ber + photo-terminal (FV-BR1) + fi ber at atmospheric side (FT-J8). Please refer to p.91~ for details.

8 Digital SERIES 146 LIST OF S FX-05 / FX-01 (Red LED type) sensing range (Note 1) Thru-beam type (one pair set) are listed in alphabetic order. Refer to p.6~ Fiber for details of each fi ber. Model No. The FX-05 and FX-01(-HS) have different sensing modes. FX-05: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-01(-HS): S-D, H-SP, FAST, STD, LONG (no STDF or U-LG mode) Sensing range (mm in) (Note 2) Red LED U-LG LONG STDF STD FAST H-SP S-D Dimensions FT-R P.109 FT-SFM2 1, P.109 FT-SFM2L 2, , P.109 FT-SFM2SV P.109 FT-SNFM P.109 FT-T80 1, P.109 FT-V10 2, , , , P.109 FT-V P.109 FT-V P.109 FT-V80Y 1, P.109 FT-W P.109 FT-W P.110 FT-WA8, (Note ), (Note ), , , , P.110 FT-WA0, (Note ), (Note ), (Note ), (Note ), (Note ), , (Note ) P.110 FT-WKV8 2, , , P.110 FT-WR P.110 FT-WR80L 1, , P.110 FT-WS P.110 FT-WS P.110 FT-WS P.110 FT-WS8L 1, , P.110 FT-WV P.110 FT-WZ P.110 FT-WZ4HB P.111 FT-WZ P.111 FT-WZ7HB P.111 FT-WZ P.111 FT-WZ8E 2, , P.111 FT-WZ8H, , , , P.111 FT-Z8 1, P.111 FT-Z8E 1, , P.111 FT-Z8H, , , , , P.111 FT-Z802Y, , , , , P.111 Notes: 1) Refer to p.76 for the sensing ranges for the FX-01-HS in H-SP mode and for the FX-01B/G/H. 2) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut. ) The fi ber cable length practically limits the sensing range to,500 mm in long.

9 147 Digital SERIES LIST OF S FX-05 / FX-01 (Red LED type) sensing range (Note 1) Retroreflective type are listed in alphabetic order. Refer to p.6~ Fiber for details of each fi ber. Model No. The FX-05 and FX-01(-HS) have different sensing modes. FX-05: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-01(-HS): S-D, H-SP, FAST, STD, LONG (no STDF or U-LG mode) Sensing range (mm in) (Note 2, ) Red LED U-LG LONG STDF STD FAST H-SP S-D Dimensions FR-KV1 15 to to to to to to to to to to to to to to.54 P.112 FR-KZ P.112 FR-KZ21E P.112 FR-WKZ to to to to to to to to to to P.112 Notes: 1) Refer to p.76 for the sensing ranges for the FX-01-HS in H-SP mode and for the FX-01B/G/H. 2) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut. The sensing range of FR-WKZ11 is specified for the RF-1. The sensing range of FR-KZ21 and FR-KZ21E is specified for the attached reflector RF-00. The sensing range of FR-KV1 is specified for the attached reflector. ) The sensing range of FR-KV1 is the possible setting range for the refl ector. The fi ber can detect an object less than 15 mm in away. The sensing range of FR-KZ21 and FR-KZ21E is the possible setting range for the refl ector. However, if setting the fi ber to detect objects passing within 0 to 20 mm 0 to in from the fi ber head, unstable detection may result. The sensing range of FR-WKZ11 is the possible setting range for the refl ective tape. The fi ber can detect an object less than 100 mm.97 in away. However, note that if there are any white or highly-refl ective surfaces near the fi ber head, refl ected incident light may affect the fi ber head. If this occurs, adjust the threshold value of the amplifi er unit before use. FX-05 / FX-01 (Red LED type) sensing range (Note 1) Reflective type are listed in alphabetic order. Refer to p.6~ Fiber for details of each fi ber. Model No. The FX-05 and FX-01(-HS) have different sensing modes. FX-05: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-01(-HS): S-D, H-SP, FAST, STD, LONG (no STDF or U-LG mode) Sensing range (mm in) (Note 2, ) Red LED U-LG LONG STDF STD FAST H-SP S-D Dimensions FD-A P.11 FD-AFM P.11 FD-AFM2E P.11 FD-B P.11 FD-E P.11 FD-E P.11 FD-EG P.11 FD-EG P.11 FD-EG P.11 FD-EN500S Cannot use Cannot use P.11 FD-ENM1S P.114 FD-F4 FD-F41 Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø0.26 to ø1.024 in transparent pipe [PFA (fl uorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.09 in] Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø0.26 to ø1.024 in transparent pipe [PVC (vinyl chloride), fl uorine resin, polycarbonate, acrylic, glass, wall thickness 1 to mm 0.09 to in] FD-F8Y P.114 FD-FM P.114 FD-FM2S P.114 FD-FM2S P.114 FD-G P.114 FD-G P.114 FD-G6X P.114 FD-H1-FM P.114 FD-H18-L1 0 to 20 0 to to 15 0 to to 10 0 to to 10 0 to to to 0.15 Cannot use 2 to to 0.26 P.115 FD-H P.115 Notes: 1) Refer to p.76 for the sensing ranges for the FX-01-HS in H-SP mode and for the FX-01B/G/H. 2) The standard sensing objects of the sensing ranges vary depending on the fi bers. Refer to p.71~ for details. ) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut. P.114 P.114

10 Digital SERIES 148 LIST OF S FX-05 / FX-01 (Red LED type) sensing range (Note 1) Reflective type are listed in alphabetic order. Refer to p.6~ Fiber for details of each fi ber. Model No. The FX-05 and FX-01(-HS) have different sensing modes. FX-05: H-SP, FAST, STD, STDF, LONG, U-LG (no S-D mode) FX-01(-HS): S-D, H-SP, FAST, STD, LONG (no STDF or U-LG mode) Sensing range (mm in) (Note 2, ) Red LED U-LG LONG STDF STD FAST H-SP S-D Dimensions FD-H20-M P.115 FD-H0-KZ1V-S (Note 4) 20 to to to to to to to to to to.97 Cannot use Cannot use P.115 FD-H0-L2 0 to 20 0 to to 15 0 to to 10 0 to to 10 0 to to to 0.15 Cannot use 2 to to 0.26 P.115 FD-H0-L2V-S (Note 4) 0 to 11 0 to to 8 0 to to to to to to to Cannot use Cannot use P.115 FD-H5-20S P.116 FD-H5-M P.116 FD-H5-M2S P to to to to to to to to to to to to to to 0.74 FD-L4 (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) P to to to to to to 0.60 to to to to FD-L41 (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) Cannot use Cannot use P.116 FD-L4 0 to 2 0 to P.116 FD-L44 0 to to to 7 0 to to to to 6 0 to to to to 5 0 to to to P.116 FD-L44S 0 to to to to to 4 0 to to 4 0 to to.8 0 to to 0 to to.5 0 to 0.18 P.116 FD-L45 0 to 50 0 to to 6 0 to to 0 to to 0 0 to to 0 0 to to 15 0 to to 21 0 to P.116 FD-L46 12 to to to to to to to to to to Cannot use Cannot use P.116 FD-NFM P.117 FD-NFM2S P.117 FD-NFM2S P.117 FD-P P.117 FD-P P.117 FD-P P.117 FD-P P.117 FD-P P.117 FD-P81X P.117 FD-R P.117 FD-S P.117 FD-SFM2SV P.117 FD-SNFM P.118 FD-T P.118 FD-T P.118 FD-V P.118 FD-W P.118 FD-W P.118 FD-WG P.118 FD-WKZ1 20 to to to to to to to to to to to to to to.97 P to to to to to to to to to to0.472 FD-WL41 (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) (Convergent point ) Cannot use Cannot use P.118 FD-WL to to to to to to to to to to Cannot use Cannot use P.119 FD-WS P.119 FD-WSG P.119 FD-WT P.119 FD-WT P.119 FD-WV Cannot use Cannot use P.119 FD-WZ4 1 to to to to to to to to to to 0.94 P.119 FD-WZ4HB 1 to to to to to to to to to to to to to to P.119 FD-WZ to to.07 1 to to to to to to to to P.119 FD-WZ7HB 0.5 to to to to to to to to.54 1 to to to to to to 1.78 P.119 Notes: 1) Refer to p.76 for the sensing ranges for the FX-01-HS in H-SP mode and for the FX-01B/G/H. 2) The standard sensing objects of the sensing ranges vary depending on the fi bers. Refer to p.71~ for details. ) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut. 4) Sold as a set comprising vacuum type fi ber + photo-terminal (FV-BR1) + fi ber at atmospheric side (FT-J8). Please refer to p.91~ for details.

11 149 Digital SERIES LENS FOR S (OPTIONAL) Lens (for thru-beam type fiber) The dimensions are on p.120~. Designation Model No. Description Expansion lens (Note 1) FX-LE1 Increases the sensing range by 5 times or more. Ambient temperature: 60 to +50 C 76 to +662 F (Note 5) Sensing range for red LED type (mm) [Lens on both sides] (Note ) Mode Fiber U-LG LONG STDF STD FAST S-D H-SP FT-B8,500 (Note 2),500 (Note 2),000 2,500 2,000 1,000 1,000 FT-FM2,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) 2,500 1,00 1,000 FT-T80,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) 2,500 1,00 1,000 FT-R80,500 (Note 2),500 (Note 2),500 (Note 2) 2,00 1, FT-W8,500 (Note 2),500 (Note 2),500 (Note 2) 2,900 2,000 1, FT-P80,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) 2,500 1,100 1,000 FT-P60,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) 1, FT-P81X 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1, FT-H5-M2,500 (Note 2),500 (Note 2) 2,500 2,000 1, FT-H20W-M1 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1, FT-H20-M1 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1, For thru-beam type fi ber Superexpansion lens (Note 1) FX-LE2 Tremendously increases the sensing range with large diameter lenses. Ambient temperature: 60 to +50 C 76 to +662 F (Note 5) Sensing range for red LED type (mm) [Lens on both sides] (Note ) Mode Fiber U-LG LONG STDF STD FAST S-D H-SP FT-B8,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-FM2,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-R80,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-W8,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-P80,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-P60,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-P81X 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) FT-H5-M2,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) FT-H20W-M1 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,500 1,600 (Note 2) FT-H20-M1 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) 1,600 (Note 2) FT-H1-FM2,500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2),500 (Note 2) Sensing range for red LED type (mm) [Lens on both sides] (Note ) Side-view lens FX-SV1 Beam axis is bent by 90. Ambient temperature: 60 to +00 C 76 to +572 F (Note 5) Mode Fiber U-LG LONG STDF STD FAST S-D H-SP FT-B8 1,450 1, FT-FM2 1,800 1, FT-T80 1,800 1, FT-W8 1, FT-P80 1,800 1, FT-P FT-P81X 1,800 1, FT-H5-M FT-H20W-M FT-H20-M Expansion lens for vacuum fi ber (Note 1) FV-LE1 Sensing range increases Sensing range for red LED type (mm) [Lens on both sides] (Note, 5) by 4 times or more. Mode Ambient temperature: Fiber U-LG LONG STDF STD FAST S-D H-SP 60 to +50 C FT-H0-M1V 1,600 1, to +662 F (Note 5) Vacuum resistant side-view lens (Note 1) FV-SV2 Beam axis is bent by Sensing range for red LED type (mm) [Lens on both sides] (Note, 4) 90. Mode Ambient temperature: Fiber U-LG LONG STDF STD FAST S-D H-SP 60 to +00 C FT-H0-M1V 1,600 1, to +572 F (Note 5) Notes: 1) Be careful when installing the thru-beam type fi ber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is diffi cult. Especially when installing a fi ber with many cores (sharp bending fi bers and heat-resistant glass fi ber), please be sure to use it only after you have adjusted it suffi ciently. 2) The fi ber cable length practically limits the sensing range to,500 mm in long (FT-P81X, FT-H20W-M1 and FT-H20-M1: 1,600 mm in). ) The sensing ranges are the values for red LED type amplifi er. Please contact our offi ce for details on sensing ranges for other types of amplifi ers. 4) The fi ber cable length for the FT-H0-M1V is 1 m.281 ft. The sensing ranges in U-LG and LONG modes take into account the length of the FT-J8 atmospheric side fi ber. 5) Refer to p.101~ for the ambient temperatures of fi bers to be used in combination.

12 Digital SERIES 150 LENS FOR S (OPTIONAL) Lens (for reflective type fiber) The dimensions are on p.121. For refl ective type fi ber Designation Model No. Description Pinpoint spot lens FX-MR1 Zoom lens FX-MR2 Finest spot lens Finest spot lens Zoom lens Side-view type FX-MR FX-MR6 FX-MR5 Screw-in depth Distance to focal point Distance to focal point Distance to focal point Spot diameter Screw-in depth Spot diameter Spot diameter Pinpoint spot of ø0.5 mm ø0.020 in. Enables detection of minute objects or small marks. Distance to focal point: 6 ± 1 mm 0.26 ±0.09 in Applicable fi bers: FD-WG4, FD-G4 Ambient temperature: 40 to +70 C 40 to +158 F (Note 2) The spot diameter is adjustable from ø0.7 to ø2 mm ø0.028 to ø0.079 in according to how much the fi ber is screwed in. Applicable fi bers: FD-WG4, FD-G4 Ambient temperature: 40 to +70 C 40 to +158 F (Note 2) Accessory: MS-EX- (mounting bracket) Extremely fi ne spot of ø0. mm ø0.012 in approx. achieved. Applicable fi bers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG, FD-G6X, FD-G6 Ambient temperature: 40 to +70 C 40 to +158 F (Note 2) Sensing range for red LED type (Note 1) Screw-in depth Distance to focal point Spot diameter 7 mm in ø18.5 mm ø0.728 in approx. ø0.7 mm ø0.028 in 12 mm in ø27 mm ø1.06 in approx. ø1.2 mm ø0.047 in 14 mm in ø4 mm ø1.69 in approx. ø2.0 mm ø0.079 in Sensing range for red LED type (Note 1) Fiber Distance to focal point Spot diameter FD-EG 7.5 ± 0.5 mm ± in ø0.15 mm ø0.006 in approx FD-EG2 7.5 ± 0.5 mm ± in ø0.2 mm ø0.008 in approx FD-EG1 7.5 ± 0.5 mm ± in ø0. mm ø0.012 in approx FD-WG4/G4/G6X/G6 7.5 ± 0.5 mm ± in ø0.5 mm ø0.020 in approx Extremely fi ne spot of ø0.1 mm Sensing range for red LED type (Note 1) ø0.004 in approx. achieved. Applicable fi bers: Fiber Distance to focal point Spot diameter FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG 7 ± 0.5 mm ± in ø0.1 mm ø0.004 in approx FD-EG, FD-G6X, FD-EG2 7 ± 0.5 mm ± in ø0.15 mm ø0.006 in approx FD-G6 Ambient temperature: FD-EG1 7 ± 0.5 mm ± in ø0.2 mm ø0.008 in approx 20 to +60 C 4 to +140 F (Note 2) FD-WG4/G4/G6X/G6 7 ± 0.5 mm ± in ø0.4 mm ø0.016 in approx FX-MR2 is converted into a side-view type and can be mounted in a very small space. Applicable fi bers: FD-WG4, FD-G4 Ambient temperature: 40 to +70 C 40 to +158 F (Note 2) Sensing range for red LED type (Note 1) Screw-in depth Distance to focal point Spot diameter 8 mm 0.15 in 1 mm in approx. ø0.5 mm ø0.020 in 10 mm 0.94 in 15 mm in approx. ø0.8 mm ø0.01 in 14 mm in 0 mm in approx. ø.0 mm ø0.118 in Notes: 1) The sensing ranges are the values when used in combination with red LED type amplifi er. Please contact our offi ce for details on sensing ranges for other types of amplifi er. 2) Refer p.101~ for the ambient temperatures of fi bers to be used in combination. Refer to p.100 for other fi ber options.

13 151 Digital SERIES SPECIFICATIONS Refer to p.101~ for specifi cations of fi bers. Model No. Type Standard type Red LED Blue LED Green LED Infrared LED High-speed type High-function type NPN output FX-01 FX-01B FX-01G FX-01H FX-01-HS FX-05 Item PNP output FX-01P FX-01BP FX-01GP FX-01HP FX-01P-HS FX-05P Supply voltage Power consumption Output Output operation Short-circuit protection Response time Sensitivity setting <Red LED / Infrared LED type> Normal operation: 960 mw or less (Current consumption 40 ma or less at 24 V supply voltage) ECO mode: 600 mw or less (Current consumption 25 ma or less at 24 V supply voltage) 12 to 24 V DC ± 10 % Ripple P-P 10 % or less <Blue LED / Green LED type> Normal operation: 720 mw or less (Current consumption 0 ma or less at 24 V supply voltage) ECO mode: 40 mw or less (Current consumption 18 ma or less at 24 V supply voltage) <NPN output type> <NPN output type> NPN open-collector transistor NPN open-collector transistor 2 outputs Maximum sink current:100 ma (50 ma, if five, or more, amplifiers are connected in cascade.) Maximum sink current: 50 ma each (Note 2) Applied voltage: 0 V DC or less (between output and 0 V) Applied voltage: 0 V DC or less (between output and 0 V) Residual voltage: 1.5 V or less [at 100 ma (at 50 ma, if five, or more, amplifiers are connected in cascade) sink current.] Residual voltage: 1.5 V or less [at 50 ma (Note 2)] <PNP output type> <PNP output type> PNP open-collector transistor Maximum source current: 100 ma (50 ma, if fi ve, or more, amplifi ers are connected in cascade.) Applied voltage: 0 V DC or less (between output and +V) Residual voltage: 1.5 V or less [at 100 ma (at 50 ma, if fi ve, or more, amplifi ers are connected in cascade) source current.] 65 μs or less [H-SP (Red LED type only)], 150 μs or less (FAST), 250 μs or less [STD / S-D (Red LED type only)], 2 ms or less (LONG), selectable with jog switch Selectable either Light-ON or Dark-ON, with jog switch Incorporated 2-level teaching / Limit teaching / Manual adjustment / Full-auto teaching / Max. sensitivity teaching 5 μs or less (H-SP), 150 μs or less (FAST), 250 μs or less (STD / S-D), 2 ms or less (LONG), selectable with jog switch PNP open-collector transistor 2 outputs Maximum source current: 50 ma each (Note 2) Applied voltage: 0 V DC or less (between output and +V) Residual voltage: 1.5 V or less [at 50 ma (Note 2)] 65 μs or less (H-SP), 150 μs or less (FAST), 250 μs or less (STD), 700 μs or less (STDF), 2.5 ms or less (LONG), 4.5 ms or less (U-LG), selectable with jog switch Normal mode: 2-level teaching / Limit teaching / Full-auto teaching / Max. sensitivity teaching / Manual adjustment Window comparator mode: Teaching (1-level / 2-level / -level) / Manual adjustment Operation indicator Orange LED (lights up when the output is ON) Stability indicator Green LED (lights up under stable light received condition or stable dark condition) MODE indicator RUN: Green LED, TEACH ADJ L/D ON TIMER PRO: Yellow LED Digital display 4 digit red LED display Fine sensitivity adjustment function Incorporated Timer function Light emitting amount selection function Automatic interference prevention function Environmental resistance Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. Timer period: Red LED type; 0.5 ms approx., 1 to 9999 ms (Blue LED, Green LED, Infrared LED type; approx. 0.5 to 500 ms) Incorporated (Red LED type only) (Note ) FAST, STD, LONG: 4 level, H-SP: level, S-D: 2 level Incorporated (Up to four sets of fiber heads can be mounted close together. However, H-SP mode is 2 fiber heads.) (Note 4) Incorporated (Note ) FAST, STD, LONG: 4 level H-SP, S-D: 2 level Incorporated with variable ON-delay / OFF-delay / ONE SHOT / ON-delay OFF-delay / ON-delay ONE SHOT timer, switchable either effective or ineffective. (Timer period: Output 1; 0.5 ms, 1 to 9999 ms, Output 2; 0.5 ms, 1 to 500 ms) Incorporated (Note ) FAST, STD, STDF, LONG, U-LG: 4 level H-SP: level Incorporated [Up to four sets of fiber heads can be mounted close together. (However, U-LG mode is 8 fiber heads, H-SP mode is 2 fiber heads.)] (Note 5) Ambient temperature 10 to +55 C +14 to 11 F (If 4 to 7 units are connected in cascade: 10 to +50 C +14 to +122 F, if 8 to 16 units are connected in cascade: 10 to +45 C +14 to +11 F) (No dew condensation or icing allowed), Storage: 20 to +70 C 4 to +158 F Ambient humidity 5 to 85 % RH, Storage: 5 to 85 % RH Ambient illuminance Incandescent light:,000 lx at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 6) Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 6) Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.00 in amplitude in X, Y and Z directions for two hours each Shock resistance 98 m/s 2 acceleration (10 G approx.) in X, Y and Z directions for fi ve times each Emitting element (modulated) Red LED Blue LED Green LED Infrared LED Red LED Red LED Peak emission wavelength 650 nm mil 470 nm mil 525 nm mil 940 nm 0.07 mil 650 nm mil 650 nm mil Material Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, MODE key: Acrylic, Jog switch: Heat-resistant ABS (FX-01B/G/H: Acrylic) Connecting method Connector (Note 7) Cable length Total length up to 100 m ft (50 m ft for 5 to 8 units, 20 m ft for 9 to 16 units) is possible with 0. mm 2, or more, cable. Weight Net weight: 20 g approx., Gross weight: 25 g approx. Accessory FX-MB1 (amplifier protection seal): 1 set FX-MB1 (amplifi er protection seal): 1 set Notes: 1) Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +2 C +7.4 F. 2) 50 ma per output. 25 ma if fi ve, or more, amplifi ers are connected in cascade. ) The light emitting amount can be zero (emission halt) in all modes. 4) When the power supply is switched on, the light emission timing is automatically set for interference prevention. 5) When the interference prevention function is set, the number of mountable fi ber heads becomes double. Furthermore, take care that the response time also becomes double. 6) The voltage withstandability and the insulation resistance values given in the above table are for the amplifi er only. 7) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cables given below. Main cable (-core) for FX-01(P)(-HS): CN-7-C1 (Cable length 1 m.281 ft), CN-7-C2 (Cable length 2 m ft), CN-7-C5 (Cable length 5 m ft) Sub cable (1-core) for FX-01(P)(-HS): CN-71-C1 (Cable length 1 m.281 ft), CN-71-C2 (Cable length 2 m ft), CN-71-C5 (Cable length 5 m ft) Main cable (4-core) for FX-05(P): CN-74-C1 (Cable length 1 m.281 ft), CN-74-C2 (Cable length 2 m ft), CN-74-C5 (Cable length 5 m ft) Sub cable (2-core) for FX-05(P): CN-72-C1 (Cable length 1 m.281 ft), CN-72-C2 (Cable length 2 m ft), CN-72-C5 (Cable length 5 m ft)

14 Digital SERIES 152 I/O CIRCUIT AND WIRING DIAGRAMS FX-01(-HS) I/O circuit diagram Sensor circuit Tr D ZD Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) 1 (Black) Output 100 ma max. (Note 2) (Blue) 0 V (Note 1) to 24 V DC ± 10% Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 50 ma max., if fi ve amplifi ers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor FX-01P(-HS) I/O circuit diagram Sensor circuit Tr D ZD Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) ma max. (Note 2) (Black) Output (Blue) 0 V (Note 1) to 24 V DC ± 10% Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 50 ma max., if fi ve amplifi ers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor FX-05 I/O circuit diagram Sensor circuit Terminal No. Color code of quick-connection cable D (Brown) +V (Note 1) 1 Tr1 (Black) Output Tr2 ZD1 (White) Output 2 50 ma max. (Note 2) 4 ZD2 50 ma max. (Note 2) 2 (Blue) 0 V (Note 1) Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 25 ma max., if fi ve amplifi ers, or more, are connected together. Symbols D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : NPN output transistor + 12 to 24 V DC ± 10% Wiring diagram Brown (Note) Black Blue (Note) + NPN output type Color code of quick-connection cable 12 to 24 V DC ± 10% Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arragement diagram Wiring diagram 1 +V Output 2 0 V Brown (Note) PNP output type Color code of quick-connection cable Black + 12 to 24 V DC ± 10% Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arragement diagram Wiring diagram 1 +V Output 2 0 V Brown (Note) Black White NPN output type Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arragement diagram 1 +V Color code of quick-connection cable Output 1 4 Output V + 12 to 24 V DC ± 10% FX-05P I/O circuit diagram Sensor circuit Tr1 Tr2 D ZD1 Internal circuit Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) 1 50 ma max. (Note 2) ZD2 (Black) Output 1 50 ma max. (Note 2) 4 (White) Output 2 2 (Blue) 0 V (Note 1) Users circuit + 12 to 24 V DC ± 10% Notes: 1) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. 2) 25 ma max., if fi ve amplifi ers, or more, are connected together. Symbols D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : PNP output transistor Wiring diagram Brown (Note) Black White PNP output type Color code of quick-connection cable 12 to 24 V DC ± 10% Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arragement diagram 1 +V Output 1 4 Output V +