DATA SHEET ML210 ML210_IT_EN_DS017REV12_IS

Size: px

Start display at page:

Download "DATA SHEET ML210 ML210_IT_EN_DS017REV12_IS"

Harry Wilkerson
5 years ago
Views:

1 DATA SHEET ML210

3 INDEX OVERALL FEATURES 2 STANDARD FEATURES 2 TECHNICAL DATA 2 ACCURACY 3 OVERALL DIMENSION 4 VISUALIZATION PAGES 5 ELECTRICAL CONNECTIONS 6 TABELLA DELLE PRECISIONI 10 ML210/MS2500: MI-001 DETAILS 11 ML210/MS2500: MI-004 DETAILS 12 HOW TO ORDER 13

4 1 di 15

5 TECHNICAL DATA Suitable For Minimum conductivity Altitude Ambient Temperature OVERALL FEATURES All the ISOMAG sensors 5 µs/cm -200 m up to 5000 m C / F - Aluminium housing C / F - Panel mounting housing Humidity Range 0 100% (IP65 -IP 67) 0-90% (IP40) without condensation, for panel mounting housing (without transparent frontal cover IP 65) STANDARD FEATURES Wall/Compact: Painted Aluminium die casting Housing materials Panel version: NORYL UL 94 V-0 black IP 67 Aluminium housing Protection Rate IP65/IP40 Panel version Power Supply/Consumption V~ (25VA) Hz Cable Gland N 6 cable gland PG 11 Data Logger 32 values + 64 alarm events Full scale value 0,4 10m/s Digital Outputs N 2 Programmable function (Pulses, alarms) 1250 Hz, 100mA, 40 Vdc Protocols ETP Dig. Input N 1, programmable function (Totalizer reset) Data Storage Eeprom values storing system in case of power failure Galvanic Isolation All the inputs/outputs are galvanically isolated from power supply up to 500 V Programming Plug In Protected plug in for the connection to PC or hand terminal Bi-Directional Yes Dual Range Yes Diagnostic Funct. Yes Empty Pipe Detect. Yes Batch Function Yes CE Certification Yes 2 di 15

6 OPTIONAL FEATURES (CHECK HOW TO ORDER, AT LAST PAGE, FOR MORE DETAILS) Housing materials Version Protection Rate Conn. Sensor Cable Power Supply/Consumption Wall/Compact: AISI304 Compact Separate IP 68 CABLE C015 - C016 for separate version CABLE C014 for separate version with pre-amplifier LCD Display Graphic display 128x64 pixels back light,3 programming keys Pulses/ Alarm Outputs Current Output Communication port Protocols Certification Measurements tolerance Accuracy (whole system converter+sensor) 18-45V~ (25 VA) 44-66Hz V (20W); 10-35V (20W) N 2, 1250 Hz, 100mA, 40 Vdc (12,5 KHz Opt.) Relais N 1, 0/4 20mA RL=1000Ω (+1 Opt.) RS 485 RS232 Profibus DP/HART/Modbus MI-001 MI-004 ACCURACY Flow rate (volume) = ±0,05% v.l. Out 4/20 ma = ± 0,08 % v.l. Frequency Out = ± 0,08% v.l. See table below 3 di 15

7 OVERALL DIMENSION Compact version 170 Sensor Separate (wall) version Panel version TERMINAL BLOCK 4 di 15

8 VISUALIZATION PAGES Flowrate and totalizes visualization Flowrate, speed values and graph Flowrate value and Full scale % graph Flowrate graph Flowrate value with currency function enabled Different visualization possibilities with the simple press of a key 5 di 15

9 ELECTRICAL CONNECTIONS Terminal block: compact/separate version ELECTRODES E1 E2 C SC INPUT RS mA + - B A + - OUT3 E C OUT3 CTS RD TD SG SC B1 B2 SH + CE E C E COILS 24V OUT1 OUT2 24V INP2 C E OUT4 SH mA Terminal block: panel mounting version Mors. M3 Morsettiera M Morsettiera M1 ON/OFF standard output (out1) 18 (out2) OUT4 C NC NO OUT3 24V OUT2 OUT1 24V COILS C NC NO E C E CE SH B2 B1 SC SH mA + A B - + SC C E2 E1 RS485 INPUT ELECTRODES ON/OFF high frequency output (out1) 19 (out2) 29 4/20 ma output +24V Internal I ma +24V Common 9(+) 10(-) ON/OFF input 10KΩ 5(+) 5/33Vdc (ON) 0/1.5Vdc (OFF) 6(+) 6 di 15

1.1 1.2 Insert sensor ND (0-3000mm) Sensor calibration data, visualized on sensor s label 1.3 1.

6 Length of the cable connecting the sensor to the converter 1.

9* Value of empty pipe sensibility detection 1.

2* Full scale value set for range N.2 2.3* Unit of measure and number of decimal place 2.

6* Duration of the pulse generated on channel 1 2.7* Duration of the pulse generated on channel 2 2.

for channel 2 (0.1Hz-1000.0Hz) (0.1Hz-10000Hz with opt. module) 2.

1* Measure filter 3.2 Low flow cut off threshold: 0-25% of full scale value 3.

4* Automatic change of measurement range 4.1 Maximum value alarm set for direct flow rate 4.

4 Minimum value alarm set for reverse flow rate 4.

6* Current output value in case of failure 4.7* Frequency output value in case of failure 4.

10 Insert sensor ND (0-3000mm) Sensor calibration data, visualized on sensor s label Type of sensor: Enter the first two characters of the sensor serial number Position for insertion sensors: 0=1/8DN, 1=1/2DN, 2=7/8DN 1.5 Factory parameters automatically calculated (ONLY for insertion sensors) 1.6 Length of the cable connecting the sensor to the converter 1.7 Enables the empty pipe detection feature 1.8* Electrodes cleaning 1.9* Value of empty pipe sensibility detection 1.10* Enables the automatic procedure of zero calibration 2.1* Full scale value set for range N.1 2.2* Full scale value set for range N.2 2.3* Unit of measure and number of decimal place 2.4* Pulse value on channel 1 2.5* Pulse value on channel 2 2.6* Duration of the pulse generated on channel 1 2.7* Duration of the pulse generated on channel Full scale freq. for channel 1 (0.1Hz Hz) (0.1Hz-10000Hz with opt. module) 2.9 Full scale freq. for channel 2 (0.1Hz Hz) (0.1Hz-10000Hz with opt. module) 2.10 Enable/disable the selection of mass units on full scale set 2.11 Specific gravity set in kg/dm³ 3.1* Measure filter 3.2 Low flow cut off threshold: 0-25% of full scale value 3.3 Enable every hour an internal cycle of calibration. Measurement stopped for 8-15 sec. 3.4* Automatic change of measurement range 4.1 Maximum value alarm set for direct flow rate 4.2 Maximum value alarm set for reverse flow rate 4.3 Minimum value alarm set for direct flow rate 4.4 Minimum value alarm set for reverse flow rate 4.5 Hysteresis threshold set for the minimum and maximum flow rate alarms 4.6* Current output value in case of failure 4.7* Frequency output value in case of failure 4.8* Batch safety timer 5.1* Total direct (positive) flow totalizers reset enable 5.2* Partial direct (positive) flow totalizers reset enable 5.3* Total reverse (negative) flow totalizers reset enable 5.4* Partial reverse (negative) flow totalizers reset enable 5.5 Reset totalizers of pulse from digital input (see page 14) 5.6 Totalizers counting lock command (see page 14) 5.7* Block measures command 5.8* Autozero calibration external command 5.9 Range change external command (see function 3.5) 5.10 Batch start/stop external command (see batch functions) 5.11*Functions assigned to input 2 7 di 15

6.1* Output 1 functions 6.2* Output 2 functions 6.3* Output 3 functions 6.4* Output 4 functions 6.

1 Choice of the communication protocol for the IF2 device 7.2 Choice of the communication protocol for the RS232 port 7.

4 Speed of the RS232 output (possible choices: 4800, 9600, 19200, 38400 bps) 7.5 Print function enable (optional) 7.

10 RS485 parity 7.11 Address value of converter (range 0-255) 7.12 Address of a further converter connected like a terminal 7.

1 Choice of the language: EN= English, IT=italian, FR= French, SP= Spanish, DE=German 8.2 Display updating frequency: 1-2-5-10 Hz 8.

5 Date and time visualization with data logger enable 8.6 Quick start menu visualization 8.

8 Visualizes the values of the partial totalizers in the unit of selected currency 8.

11* Value of conversion/currency for reverse totalizer 8.

11 6.1* Output 1 functions 6.2* Output 2 functions 6.3* Output 3 functions 6.4* Output 4 functions 6.5* Choice of the function and the range of current output n.1 6.6* Choice of the function and the range of current output n Choice of the communication protocol for the IF2 device 7.2 Choice of the communication protocol for the RS232 port 7.3 Speed of the RS485 output (possible choices: 4800, 9600, 19200, bps) 7.4 Speed of the RS232 output (possible choices: 4800, 9600, 19200, bps) 7.5 Print function enable (optional) 7.6 Print of the performed batch 7.7 Print of the data process on regular intervals 7.8 Print of events 7.9 Instrument answer delay 7.10 RS485 parity 7.11 Address value of converter (range 0-255) 7.12 Address of a further converter connected like a terminal 7.13 Start remote connection to the terminal. Connection interrupted after 10sec. of inactivity 8.1 Choice of the language: EN= English, IT=italian, FR= French, SP= Spanish, DE=German 8.2 Display updating frequency: Hz 8.3* Display contrast 8.4 Partial totalizer visualization (with batch enable the function is always on) 8.5 Date and time visualization with data logger enable 8.6 Quick start menu visualization 8.7 Enable the page of net totalizer (difference between direct and reverse) 8.8 Visualizes the values of the partial totalizers in the unit of selected currency 8.9 Choice of the numbers of decimals for the visualization currency value: From 0 to * Value of conversion/currency for direct totalizer 8.11* Value of conversion/currency for reverse totalizer 8.12 Reset processor of the display (useful in case of particular badly operations of the display) 8.13* Total direct (positive) flow totalizer reset 8.14* Partial direct (positive) flow totalizer reset 8.15* Total reverse (negative) flow totalizer reset 8.16* Partial reverse (negative) flow totalizer reset 9.1* Date and time set 9.2 Automatic data logger enable 9.3 Interval time for the data logging function: 1, 2, 3, 6, 8, 12, 24, 48 hours 9.4 Displaying of the data stored in the data logger 9.5 Displaying of the last 64 alarms stored in the data logger 9.6 Visualization function of minimum and maximum peak of flow rate 9.7 Logged data cancel function 9.8 Reset all alarm events 9.9 Reset all minimum and maximum peak of flow rate stored 8 di 15

10.1* Calibration of the converter 10.2* Autotest converter 10.

4 Firmware revision/version 11.1 Level 2 access code enter 11.

6 Ks coefficient (only for service purposes) Menu 12: batch

1* Number of batch cycles to define the value of compensation.

12 10.1* Calibration of the converter 10.2* Autotest converter 10.3* Flow rate simulation enabling 10.4 Firmware revision/version 11.1 Level 2 access code enter 11.2 Load factory data pre-set 11.3 Load user data saved 11.4 Save user data 11.5 Ignore the calibration error during the switch on test 11.6 Ks coefficient (only for service purposes) Menu 12: batch function 12.1* Number of batch cycles to define the value of compensation. Value 0=OFF 12.2* % limit of compensation threshold 12.3* Compensation value 12.4* Prebatch value 12.5* Auto-batch 12.6* Automatic selection of batch formula 12.7* Static consent of batch 9 di 15

13 TABELLA DELLE PRECISIONI e % Fullbore sensor Tipico profilo dell errore ( puramente rappresentativo) 0,1 m/s 0,33 ft/sec 0,5 m/s 1,64 ft/sec speed 0,5 m/s (1,64 ft/s) e = +/- A % (reading value) speed < 0,5 m/s (1,64 ft/s) e = +/- (B/V) % (reading value) minimum flow (l/s): DN x DN x 0,008/1000( DN expressed in mm ) where: e = ACCURACY 5,0 m/s 16,4 ft/sec V = WORKING SPEED 10,0 m/s 32,8 ft/sec SPEED (A and B values: see below table according to CONVERTER model) MS501/MS1000/MS2410/MS2500 MS 600 MS5000 A B(m/s) B(ft/s) A B(m/s) B(ft/s) A B(m/s) B(ft/s) 0,2 0,1 0,33 0,4 0,2 0, ,28 Insertion sensors See sensors DATA SHEET Reference conditions below and as per internal testing procedures: Constant flow rate during the test Pressure: >30 Kpa Flow condition : fully developed flow profile Zero stability +/- 0,005 % 10 di 15

14 ML210/MS2500: MI-001 DETAILS The sensor s diameters listed below, coupled with ML210, ML110 and 255 are certified according to European Directive 2004/22CE category MI-001 (OIML R49) SENSOR mm SIZE inch 1 1 ¼ 1 ½ 2 2 ½ Q1 m³/h Q2 m³/h Q3 m³/h Q4 m³/h R Q3/Q1 160 (ML210-ML110) R Q3/Q1 from 100 up to 400 (ML255) Q3 allowed range: MI-001 ALLOWABLE RANGE /m 3 h -1 /dm 3 s -1 /m 3 h -1 /dm 3 s -1 /m 3 h -1 /dm 3 s -1 /m 3 h -1 /dm 3 s -1 /m 3 h -1 /dm 3 s ,278 1,6 0,444 2,5 0, ,111 6,3 1, , , , , , , , , , , , , , R (= Q3/Q1) allowed range 10 12, , Q2/Q1=1,6 Q4/Q3=1, OIML R49 ACCURACY CLASS 2 (Maximum permissible Error) MPE / % Q1 Q2 Q3 Q (Q3<100m³/h) (0,1<T<30 C) (Q3<100m³/h) (T>30 C) OIML R49-1:2006 (E) MS2500 profilo tipico curva errori 11 di 15

15 ML210/MS2500: MI-004 DETAILS The sensor s diameters listed below, coupled with ML210 and ML110, are certified according to European Directive 2004/22CE category MI-004 Sensor ND mm inch 1 1 ¼ 1 ½ 2 2 ½ q i m³/h ,1 q p m³/h q p (10m/s) m³/h q p /q i Sensor ND mm inch 1 1 ¼ 1 ½ 2 2 ½ qi m³/h ,1 qp m³/h qp (5m/s) m³/h q p /q i Sensor ND mm inch 1 1 ¼ 1 ½ 2 2 ½ qi m³/h ,1 qp m³/h qp (2;5m/s) m³/h q p /q i Sensor ND mm inch 1 1 ¼ 1 ½ 2 2 ½ qi m³/h ,1 qp m³/h qp (1,0m/s) m³/h q p /q i MPE / % 1 qi 0-1 0,1qp qp q/q p % Maximum permitted error Typical MS2500's accuracy profile 12 di 15

16 HOW TO ORDER CODE EXAMPLE Display A A B C WITHOUT DISLAY ( BLIND EXECUTION) Graphic LCD WSTN-GREEN -back light display, point matrix 128 x 64, 8 line each of 16 characters and 3 keys Graphic LCD WSTN-WHITE -back light display, point matrix 128 x 64, 8 line each of 16 characters and 3 keys Housing material / Protection rate 0 Painted aluminum die casting, protection rate IP67 1 AISI304 Stainless Steel housing, protection rate IP67 ( DISPLAY NOT ROTABLE ) 0 2 NORYL UL 94 V-0 black ( ONLY F VERSION ) IP 40 3 NORYL UL 94 V-0 BLACK ( ONLY F VERSION )+TRANSPARENT FRONTAL COVER IP 65 4 Painted aluminum die casting, protection rate IPXX, preset for CUSTOMER CABLE GLAND (Total Dim. Max available 105 x 52 mm) 9 Painted aluminum die casting, protection rate IP68 (special version CONTACT THE FACTORY) Version A Compact version with sensor MS... (liquid maximum temperature 100 C) A Power supply 1 Analogue output A Serial Interface B D F Separate version ( CABLE C015-C016 OR C014 with preamp. ) for wall monting, complete with mounting accessories in Aluminum (painted RAL6028) Separate version ( CABLE C015-C016 OR C014 with preamp. ) for wall monting, complete with mounting accessories in AISI304 Separate version ( CABLE C015-C016 OR C014 with preamp. ) for FRONT PANEL mounting according DIN 43700(72x144) complete with mounting accessories; AVAILABLE ONLY FOR HOUSING MATERIALS OPTIONS 2 AND 3 ( SEE ABOVE ) 1 Power supply : V Hz 2 Power supply : VAC-DC / Hz 3 Power supply : V dc 9 Power supply : other A B Without Analogue output Analogue output 0/4...20/22 ma 1 Without RS485 Serial Interface 1 Additional module 2 RS485 Serial Interface 3 Modbus protocol over RS 485 interface A A C D E F G P T Without additional module ME200; n. 2 additional ON / OFF programmable output + 1 ON/OFF INPUT ME201; n. 2 additional ON / OFF programmable output (one of them at 10 KHz frequency)+ 1 ON/OFF INPUT ME202; additionals 0/4 20 ma + n.2 ON / OFF programmable output + 1 ON/OFF INPUT ME203; n. 1 RS232 serial interface + n.2 additional ON / OFF programmable output + 1 ON/OFF INPUT ME204; n. 1 RS232 serial interface + additionals 0/4 20 ma + n.2 ON / OFF program. output + 1 ON/OFF INPUT ME205; n. 2 relè output (each with 1 NO contact + 1 NC contact, 2A - 60 Vca, 60W 125 VA) ME207; n. 2 relè output (each with 1 NO contact + 1 NC contact, 2A Vca, 60W 125 VA) H ME 100 ; Profibus DP communication module ( NOT POSSIBLE IF HOUSING MATERIAL 2 AND 3) 1 BlueTooth INTERFACE 2 ME101 - HART PROTOCOL OUT ( NOT POSSIBLE IF HOUSING MATERIAL 2 AND 3) Hart certified. Z Other 13 di 15

17 Special Features 0 NONE 0 1 WITH ANTICONDENSE CAP 2 n 4 CABLE GLAND 1/2 NPT - IP68 - Nickel plated brass CODE ( CABLE 6-12 mm ) 3 PAINT RAL9005 (BLACK) ML210-A0A1A1A0 (Complete code example for order) 14 di 15

ISOIL INDUSTRIA S.p.A. HEAD OFFICE SERVICE Via Fratelli Gracchi, 27 isomagservice@isoil.it 20092 Cinisello Balsamo (MI) Tel +39 02 66027.1 Fax +39 02 6123202 vendite@isoil.

asp If you want to find the complete list of our distributors access at the following link: http://www.isoil.com/u_vendita.

18 ISOIL INDUSTRIA S.p.A. HEAD OFFICE SERVICE Via Fratelli Gracchi, Cinisello Balsamo (MI) Tel Fax If you want to find the complete list of our distributors access at the following link: If you want to find the complete list of our distributors access at the following link: BEFORE returning any material, please contact our SERVICE at the adress: Due to the constant technical development and improvement of its products, the manufacturer reserves the right to make changes and/or modify the information contained in this document without notice. AZIENDA CON SISTEMA DI GESTIONE QUALITA CERTIFICATO DA DNV GL

ISOMAG THE FRIENDLY MAG METER. Gas, mists or vapours Zone 0 1G Gas, mists or vapours Zone 1 2G. Gas, mists or vapours Zone 2 3G

ISOMAG THE FRIENDLY MAG METER. Gas, mists or vapours Zone 0 1G Gas, mists or vapours Zone 1 2G. Gas, mists or vapours Zone 2 3G ISOMAG THE FRIENDLY MAG METER Converter EX CONVERTER Hazardous area Categories according to 94/9/CE Directive Gas, mists or vapours Zone 0 1G Gas, mists or vapours Zone 1 2G Gas, mists or vapours Zone