Aalto TMS Laboratory. Quick Start Manuals MAGSTIM SUPER RAPID PLUS QUICK START
|
|
- Alaina Owens
- 6 years ago
- Views:
Transcription
1 QUICK START Author, date: Mikko Nyrhinen, Edited (name, date): Figure 1. Magstim Super Rabid Plus (1.) with User Interface(2.), Air cooled coil (3.) and Numatic Cooling System (4.). Contents Technical Specifications [1]:... 2 Starting Measurements... 2 Stimulation... 6 Main menu... 3 Single pulse mode (MEP)... 4 'Aalto University Postal Address Street Address Contacts School of Science P.O. BOX Otakaari 5 I +358 (0) Aalto TMS Laboratory AALTO Espoo aaltotms-sci@aalto.fi amiserver/project/tms_internal/tms_documents/official/2013/eng/aalto_tms_magstim_rapid_quick_start 1/7
2 Repetive Mode... 4 Session Mode... 5 Stimulus Computer... 7 After the experiment... 7 Technical Specifications [1]: Stimulation Frequency: Pulse Characteristics: 1 Hz at 100% power output in single pulse mode 0.50 Hz at % power output in single pulse mode 100 Hz at 0-48% power output in repetitive mode Hz at % power output in repetitive mode Biphasic Single Cosine, 400µs period Starting Measurements Figure 2. Magstim Super Rabid² Plus¹ backside view power swithes marked in the image. Turn system on by turning Mains Power Switch and Plus Mains Power Switch (figure 2). 2/7
3 Figure 3. Magstim Super Rabid² Plus¹ frontside view. ON/Standby Button (1.), ON/Standby status led (2.), Arm Button (3.), internal discharge button (4.), trigger button (5.), rmed led (6.) and output control knop (7.) indicated. Push ON/STANDBY button(figure 3: 1.). Green led flashes when the system is on stand by and is solid green when on. The yellow light is lit when the system is armed, that is ready for stimulation (figure 3: 6.). Main menu Figure 4. Main menu [1]. Select stimulation mode. There are three different stimulation modes single, repetitive and session. Select using touch screen (figure 4). 3/7
4 Single pulse mode (MEP) Figure 5. Single Pulse mode Power menu [1]. Select and adjust stimulation output (figure 5). Select by touch screen and adjust with After you've acquired motor/phosphene threshold you can use the %MT to select a percentage of the motor threshold and the system calculates the protocol intensity automatically. There is a guide for evaluating motor and phosphene thresholds with the laboratory equipment. Enhanced button enables to use power up to 110% (available only with single pulse mode). After selecting procol intensities you can start stimulating by arming the system (figure 3: 3.) or move the power setup to repetetive or session mode by selecting repetetive / session from the touch screen (figure 5). Proceed to Section Stimulation Repetive Mode Figure 6. Repetive mode setup [1]. There are two options to repetitive mode: standard and burst. Repetetive mode display has an illustration of the used protocol (figure 6). Select and adjust parameters with touch screen and output control knop. When ready press Run Session. 4/7
5 Repetive mode screen opens (figure 7). Proceed to section Stimulation. Figure 7. Repetive mode session [1]. Session Mode Session mode enables to run various simulation protocols with one trigger. Select by touch screen and adjust with turn knop (figure 3). When ready press Run session. Proceed as in single pulse and repetitive mode. 5/7
6 Stimulation Figure 8. User Interface. Select parameters to adjust by touch screen (1.), output control knop (2.), arm button (3.), trigger button (4.) and internal discharge (5.) button. Use touch screen to select and output control knob to change values (figure 3). The green button arms the system so that TMS pulse can be triggered by foot switch or yellow trigger button. The red System stop button disarms the capasitor internally. The system can only be armed when one of the stimulation modes is selected. When arming the system the user interface askes if you want to disable the safety switch. Disabling the coil switch enables system to be triggered either by foot pedal or trigger-in (stimulus computer) without one or both of the coil safety switches is being pressed (figure 4). If the coil heats up during session (figure 6 & 8: temperature), start Numatic cooling system until coil is cool enough to continue (figure 4). Figure 9. Air Cooled Coil and Numatic cooling system. 6/7
7 Stimulus Computer Aalto TMS Laboratory The system can be triggered with simulation computer by sending number 2 to LPT1-port. After the experiment Press system stop button from the user interface (figure 8: 3.). Push ON/STANDBY (figure 3: 1.). Turn system off by turning Mains Power Switch and Plus Mains Power Switch (figure 2). References [1] MAGSTIM RAPID², P/N MOP03-EN-01, OPERATING MANUAL, JUNE /7
Auxiliary states devices
22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary
More informationMarks and Grades Project
Marks and Grades Project This project uses the HCS12 to allow for user input of class grades to determine the letter grade and overall GPA for all classes. Interface: The left-most DIP switch (SW1) is
More information2000 W, 2450 MHz Microwave Generator GMP 20K SM 56M230 FST 3 IR
2000 W, 2450 MHz Microwave Generator GMP 20K SM 56M230 FST 3 IR Power supply It is based upon the latest switch mode power supply technology, offering size reduction (i.e. 19 rack, 3U power supply), good
More informationModulating musical reward sensitivity up and down with transcranial magnetic stimulation
SUPPLEMENTARY INFORMATION Letters https://doi.org/10.1038/s41562-017-0241-z In the format provided by the authors and unedited. Modulating musical reward sensitivity up and down with transcranial magnetic
More informationThe DataView PowerPad III Control Panel
Setting Up a Recording Session in the DataView PowerPad III Control Panel By Mike Van Dunk The DataView PowerPad III Control Panel is designed for working with AEMC PowerPad III Power Quality Analyzers,
More informationUser interface. Abbreviations / Meanings
RG66012649 User interface Contents Page Abbreviations / Meanings Abbreviations / meanings... 2 Button Identification... 3 On-screen Indicators... 4 Quick Start... 5 Setting the time and day... 5 Changing
More informationCBF500 High resolution Streak camera
High resolution Streak camera Features 400 900 nm spectral sensitivity 5 ps impulse response 10 ps trigger jitter Trigger external or command 5 to 50 ns analysis duration 1024 x 1024, 12-bit readout camera
More informationViewing Serial Data on the Keysight Oscilloscopes
Ming Hsieh Department of Electrical Engineering EE 109L - Introduction to Embedded Systems Viewing Serial Data on the Keysight Oscilloscopes by Allan G. Weber 1 Introduction The four-channel Keysight (ex-agilent)
More informationTopic: Instructional David G. Thomas December 23, 2015
Procedure to Setup a 3ɸ Linear Motor This is a guide to configure a 3ɸ linear motor using either analog or digital encoder feedback with an Elmo Gold Line drive. Topic: Instructional David G. Thomas December
More informationNew Generation of MEA-Systems: MEA2100-System
New Generation of MEA-Systems: MEA2100-System Integrated stimulation Gain and bandwidth adjustable via software Up to 240 recording channels Variable contact unit for microelectrode arrays with 32, 60
More informationViewing Serial Data on the Keysight Oscilloscopes
Ming Hsieh Department of Electrical Engineering EE 109L - Introduction to Embedded Systems Viewing Serial Data on the Keysight Oscilloscopes by Allan G. Weber 1 Introduction The four-channel Keysight (ex-agilent)
More informationBrain-Computer Interface (BCI)
Brain-Computer Interface (BCI) Christoph Guger, Günter Edlinger, g.tec Guger Technologies OEG Herbersteinstr. 60, 8020 Graz, Austria, guger@gtec.at This tutorial shows HOW-TO find and extract proper signal
More informationPart No. ENC-LAB01 Users Manual Introduction EncoderLAB
PCA Incremental Encoder Laboratory For Testing and Simulating Incremental Encoder signals Part No. ENC-LAB01 Users Manual The Encoder Laboratory combines into the one housing and updates two separate encoder
More informationTVS-2-TAIT VPU-15-TAIT
TVS-2-TAIT High Level Rolling Code Scrambler for the Tait Orca & TM-8000 Radios VPU-15-TAIT Voice Inversion Scrambler for the Tait Orca & TM-8000 Radios Manual Revision: 2018-03-05 Rev B Covers Software
More informationSwiftMix Automation Safety
Operations Manual SwiftMix TM Automation Thank you for your purchase of the SwiftMix automation for the 5088 console. Everyone at Rupert Neve Designs hopes you enjoy using this tool as much as we have
More informationMains Supply. 2-wire mains-rated, 0.5 mm² to 1.5 mm² Max. length 300 m (with 1.5 mm² cable). Example: Belden 8471.
4Channel Ballast Controller (474) Product Description Installation and User Guide The Digidim 474 is a fourchannel ballast controller fitted with highinrush relays rated at 16 A per channel, which handle
More informationDDA-UG-E Rev E ISSUED: December 1999 ²
7LPHEDVH0RGHVDQG6HWXS 7LPHEDVH6DPSOLQJ0RGHV Depending on the timebase, you may choose from three sampling modes: Single-Shot, RIS (Random Interleaved Sampling), or Roll mode. Furthermore, for timebases
More informationCommon Spatial Patterns 3 class BCI V Copyright 2012 g.tec medical engineering GmbH
g.tec medical engineering GmbH Sierningstrasse 14, A-4521 Schiedlberg Austria - Europe Tel.: (43)-7251-22240-0 Fax: (43)-7251-22240-39 office@gtec.at, http://www.gtec.at Common Spatial Patterns 3 class
More informationModule 28 Scan Tool Advanced
Module 28 Scan Tool Advanced Author: Grant Swaim E-mail: sureseal@nr.infi.net URL: www.tech2tech.net Phone: (336) 632-9882 Fax: (336) 632-9688 Postal Address: Tech-2-Tech Website PO Box 18443 Greensboro,
More informationPackage Contents. LED Protocols Supported. Safety Information. Physical Dimensions
Pixel Triton Table of Contents Package Contents... 1 Safety Information... 1 LED Protocols Supported... 1 Physical Dimensions... 1 Software Features... 2 LED Status... 2 Power... 2 Activity LED... 2 Link
More informationEAN-Performance and Latency
EAN-Performance and Latency PN: EAN-Performance-and-Latency 6/4/2018 SightLine Applications, Inc. Contact: Web: sightlineapplications.com Sales: sales@sightlineapplications.com Support: support@sightlineapplications.com
More informationSERVICE MANUAL COOKING. Built-in ovens. S.E.T. (Simple Electronic Timer) Electronic Programmer. Publication Corso Lino Zanussi,30
SERVICE MANUAL COOKING Built-in ovens ELECTROLUX ZANUSSI S.p.A. Publication Corso Lino Zanussi,30 number I - 33080 PORCIA /PN (ITAL) 599 72 74-2 Tel +39 0434 394850 Fax +39 0434 394096 EN/SERVICE/FV S.E.T.
More informationUsing Manchester and NRZ Configurable Protocol Decoders
Using Manchester and NRZ Configurable Protocol Decoders TECHNICAL BRIEF March 14, 2013 Summary Manchester and NRZ encoding schemes serve as building blocks for industrystandard and custom protocols. Here
More information3214NXT. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference
3214NXT Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference Table of Contents Job Specification Sheet 3 Timer Operation 4 System Operation in Service 6 Flow in a Four-Unit
More informationCommon Spatial Patterns 2 class BCI V Copyright 2012 g.tec medical engineering GmbH
g.tec medical engineering GmbH Sierningstrasse 14, A-4521 Schiedlberg Austria - Europe Tel.: (43)-7251-22240-0 Fax: (43)-7251-22240-39 office@gtec.at, http://www.gtec.at Common Spatial Patterns 2 class
More informationAmerican DJ. Show Designer. Software Revision 2.08
American DJ Show Designer Software Revision 2.08 American DJ 4295 Charter Street Los Angeles, CA 90058 USA E-mail: support@ameriandj.com Web: www.americandj.com OVERVIEW Show Designer is a new lighting
More informationISCEV SINGLE CHANNEL ERG PROTOCOL DESIGN
ISCEV SINGLE CHANNEL ERG PROTOCOL DESIGN This spreadsheet has been created to help design a protocol before actually entering the parameters into the Espion software. It details all the protocol parameters
More informationThis document is a reference document that shows the menus in the 5500sc, 9610sc and 9611sc analyzers. There are 3 top-level menus:
Controller menus 5500sc, 9610sc and 9611sc analyzers DOC273.53.80566 Introduction This document is a reference document that shows the menus in the 5500sc, 9610sc and 9611sc analyzers. There are 3 top-level
More informationSG-6005xl & SG-6006 PROTOCOL (VER 1.2)
SG-6005xl & SG-6006 PROTOCOL (VER 1.2) A protocol for the SG-6005xl & SG-6006 is described below. For RS-232: A null-modem connection between the PC and the SG-6005xl & SG-6006 is required, and data is
More informationLM-TV09-4K2K. 4K video wall controller. User. Manual
LM-TV09-4K2K 4K video wall controller User Manual Catalog 1.Installation Instructions 1 2.Product Brief 2 3.Controller Installed 3 4.Remote Control Settings 6 5.Pressing Setting 7 6.Specifications 7 1
More informationRevision History. SDG2000X Firmware Revision History and Update Instructions
Revision History Date Version Revision 2/28/2018 2.01.01.23R8 Optimized calibration and PV process on the production line. 8/29/2017 2.01.01.23R7 1. Supported system recovery from U-disk. 2. Fixed a bug
More informationWaveView. and. WaveCal
WaveView and WaveCal WaveView Introduction 1 Software Startup & Sample Acquisition 3 Startup WaveView 3 Configure Channels 5 Configure Acquisition 6 Collect and View Data 6 Store Data [and View File Data]
More informationLab 2: A/D, D/A, and Sampling Theorem
Lab 2: A/D, D/A, and Sampling Theorem Introduction The purpose of this lab is to explore the principles of analog-to-digital conversion, digital-to-analog conversion, and the sampling theorem. It will
More information013-RD
Engineering Note Topic: Product Affected: JAZ-PX Lamp Module Jaz Date Issued: 08/27/2010 Description The Jaz PX lamp is a pulsed, short arc xenon lamp for UV-VIS applications such as absorbance, bioreflectance,
More informationTransmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
More informationA dedicated data acquisition system for ion velocity measurements of laser produced plasmas
A dedicated data acquisition system for ion velocity measurements of laser produced plasmas N Sreedhar, S Nigam, Y B S R Prasad, V K Senecha & C P Navathe Laser Plasma Division, Centre for Advanced Technology,
More informationController, Scheduler-Timer Model UCS-01. User Guide
Model UCS-01 User Guide QUICK REFERENCE GUIDE Time Date IDLE SCREEN 03:50PM [RUN] 05/09/06 Tue Day of the Week Schedule Mode (change via 'Set Time') [OFF] = No Events Operate [RUN] = Run 'R' Events Operate
More informationWAVEJET 300 SERIES OSCILLOSCOPES. New Cover to Come. Unmatched Performance, Portability, and Value
WAVEJET 300 SERIES OSCILLOSCOPES New Cover to Come Unmatched Performance, Portability, and Value ALL THE TOOLS YOU NEED Automatic Measurements Save time making measurements on your signals by using the
More informationReal-Time PCR System TC
Detecting amplifier Real-Time PCR System TC 9443-007 - 46482062-2004 TECHNICAL PASSPORT ЛТОК 170604.00 DNA-Technology research-and-production close corporation Moscow, 2004 Contents 1. General information...
More informationFeatures of the 745T-20C: Applications of the 745T-20C: Model 745T-20C 20 Channel Digital Delay Generator
20 Channel Digital Delay Generator Features of the 745T-20C: 20 Independent delay channels - 100 ps resolution - 25 ps rms jitter - 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every
More information210E - 210ECL ECL ECL
210E - 210ECL - 2010ECL - 2018ECL RMS Signal Monitor Operations Manual THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE FOLLOWING SERIES OF MODEL 210/2010/2018 SIGNAL MONITORS, PCB Issue G: 210E, 210ECL,
More informationInstructions for DataMark PDF Temperature Logger
Instructions for DataMark PDF Temperature Logger DataMark provides a convenient way to obtain high accuracy temperature data in transit. The unit is a self contained temperature logger that plugs directly
More informationSINGLE ZONE CLIMATE ZONING SYSTEM. Technical Manual. Polyaire Pty Ltd
SINGLE ZONE CLIMATE ZONING SYSTEM Technical Manual Polyaire Pty Ltd 11-13 White Road GEPPS CROSS South Australia, 5094 Tel: (08) 8349 8466 Fax: (08) 8349 8446 www.polyaire.com.au CONTENTS Features 1 Application
More informationGFT Channel Digital Delay Generator
Features 20 independent delay Channels 100 ps resolution 25 ps rms jitter 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every channel Fours Triggers Three are repetitive from three
More informationVSP 168HD Quick Start
VSP 168HD Quick Start Support 10Gbps of transmission rate Support HDBaseT protocols and standards Support USB upgrade Max 2048 1152@60Hz/2560 816 60Hz input/output resolution Support custom output resolution
More informationWELDING CONTROL UNIT: TE 450 USER MANUAL
j WELDING CONTROL UNIT: TE 450 USER MANUAL RELEASE SOFTWARE No. 1.50 DOCUMENT NUMBER: MAN 4097 EDITION: MARCH 1998 This page is left blank intentionally. 2 / 34 TABLE OF CONTENTS SUBJECTS PAGE WELDING
More informationSTB Front Panel User s Guide
S ET-TOP BOX FRONT PANEL USER S GUIDE 1. Introduction The Set-Top Box (STB) Front Panel has the following demonstration capabilities: Pressing 1 of the 8 capacitive sensing pads lights up that pad s corresponding
More informationOverview. Know Your Oscilloscope. Front Panel. Rear Panel. Sharing Agilent s Resources with Engineering Educators
Know Your Oscilloscope Overview Front Panel Sharing Agilent s Resources with Engineering Educators www.educatorscorner.com Horizontal (time) controls Run control Special purpose menus/controls Trigger
More informationAgilent DSO5014A Oscilloscope Tutorial
Contents UNIVERSITY OF CALIFORNIA AT BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences EE105 Lab Experiments Agilent DSO5014A Oscilloscope Tutorial 1 Introduction
More informationYAMAHA 03D SERIAL AUDIO MIXER
TECH NOTE Super Edit Version 8.0 (VPE) or Version 2.0 (DPE) and later YAMAHA 03D SERIAL AUDIO MIXER The DPE/VPE editing systems interface to the 03D Serial Audio Mixer with a single RS-422 control cable
More informationFOREST SHUTTLE S / L / M RECEIVER
2 FOREST SHUTTLE S / L / M RECEIVER QUICK INSTALLATION OF ASSEMBLED TRACKS : Programming Shuttle S / L / M Receiver to a channel One pre-assembled motorized curtain track systems is standard programmed
More informationWAVEJET 300 SERIES OSCILLOSCOPES. Unmatched Performance, Portability, and Value
WAVEJET 300 SERIES OSCILLOSCOPES Unmatched Performance, Portability, and Value 1 WAVEJET 300 SERIES Unique Capabilities in a Low Bandwidth Oscilloscope The WaveJet 300 Series features unmatched performance
More informationSynchronization Check Relay ARGUS 7
Synchronization Check Relay ARGUS 7 Page 1 of 8 Table of Contents Secondary injection tests:... 3 Phase Angle Test:... 3 CS PHASE ANGLE:... 3 SS PHASE ANGLE:... 3 SLIP FREQUENCY TEST:... 4 CS SLIP FREQUENCY:...
More informationDimensions. Model Number. Electrical connection. Features. Pinout Product information. Indicators/operating means. LGS25 Serie.
Q Dimensions Transmitter Detection field + 9. Detection field 7.8 n Beam. Beam Receiver III 0. 0 Fix H H H Fn Model Number Light grid with fixed cable with -pin, M x connector, and fixed cable with 8-pin,
More informationSigPlay User s Guide
SigPlay User s Guide . . SigPlay32 User's Guide? Version 3.4 Copyright? 2001 TDT. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
More informationDX-10 tm Digital Interface User s Guide
DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What
More informationUsers Manual. Stroboscope. September 2014
820-2 Stroboscope Users Manual September 2014 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective companies.
More informationIII Phrase Sampler. User Manual
III Phrase Sampler User Manual Version 3.3 Software Active MIDI Sync Jun 2014 800-530-4699 817-421-2762, outside of USA mnelson@boomerangmusic.com Boomerang III Phrase Sampler Version 3.3, Active MIDI
More informationToshiba TLP-B2 Training Module Introduction
Toshiba TLP-B2 Training Module Introduction Toshiba TLP-B2 Introduction Welcome! Welcome to the Toshiba TLP-B2 training module offered by UT Career Services! It is highly recommended that all faculty &
More informationKONTROL channels DMX controller USER MANUAL. For safety, please read this user manual carefully before initial use.
KONTROL192 192 channels DMX controller USER MANUAL For safety, please read this user manual carefully before initial use. Event Lighting reserves the right to revise the manual at any time. Information
More informationMortara X-Scribe Tango+ Interface Notes
Mortara X-Scribe Tango+ Interface Notes To setup Tango+ with the X-Scribe stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate
More informationCOMPOSITE VIDEO LUMINANCE METER MODEL VLM-40 LUMINANCE MODEL VLM-40 NTSC TECHNICAL INSTRUCTION MANUAL
COMPOSITE VIDEO METER MODEL VLM- COMPOSITE VIDEO METER MODEL VLM- NTSC TECHNICAL INSTRUCTION MANUAL VLM- NTSC TECHNICAL INSTRUCTION MANUAL INTRODUCTION EASY-TO-USE VIDEO LEVEL METER... SIMULTANEOUS DISPLAY...
More informationDigital Delay / Pulse Generator DG535 Digital delay and pulse generator (4-channel)
Digital Delay / Pulse Generator Digital delay and pulse generator (4-channel) Digital Delay/Pulse Generator Four independent delay channels Two fully defined pulse channels 5 ps delay resolution 50 ps
More informationBME 3512 Biomedical Laboratory Equipment List
BME 3512 Biomedical Laboratory Equipment List Agilent E3630A DC Power Supply Agilent 54622A Digital Oscilloscope Agilent 33120A Function / Waveform Generator APPA 95 Digital Multimeter Component Layout
More informationMarquette Case 12, Case 15, Case 16, and Centra Stress Systems Tango M2 Interface Notes
Marquette Case 12, Case 15, Case 16, and Centra Stress Systems Tango M2 Interface Notes To setup Tango M2 with your stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger
More informationSetting up the communication between a Total Station and SiteMaster range of products
Setting up the communication between a Total Station and SiteMaster range of products Before we set up the communication, one important thing to know.. Please NOTE that to check any setup and take measurements
More informationFlat LED Par Can Light
Flat LED Par Can Light EDD-GL-200 USER MANUAL 1. Introduction 3 Thank you for purchasing our Million Color Flat LED light. Please read these instructions carefully before operating to avoid any possible
More informationINSTRUCTION MANUAL COMMANDER BDH MIG
INSTRUCTION MANUAL COMMANDER BDH MIG Valid from 0327 50173001A Version 1.0 CONTENTS INTRODUCTION... 0-1 1. PRIMARY OPERATIONAL FUNCTIONS... 1-1 Reading and setting... 1-1 Programmes... 1-2 Trigger function...
More information4125 system setup and deployment quick start guide
4125 system setup and deployment quick start guide OPERATION IN AIR Do not operate the system while the tow fish in air for extended periods. The system may be enabled to transmit while in air for test
More informationUSER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1
by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information
More informationProgramat P310. Economical firing performance. Top-quality results. The user-friendly furnace. Now with new OSD display
Programat P310 The user-friendly furnace Economical firing performance. Top-quality results. Now with new OSD display The most economical Programat of all time. Proven The firing and press furnaces from
More informationChapter 23 Dimmer monitoring
Chapter 23 Dimmer monitoring ETC consoles may be connected to ETC Sensor dimming systems via the ETCLink communication protocol. In this configuration, the console operates a dimmer monitoring system that
More informationUSER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0
by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information
More informationSHOWLINE SL PUNCHLITE 220 LED LUMINAIRE SPECIFICATIONS.
SHOWLINE SL PUNCHLITE 220 LED LUMINAIRE SPECIFICATIONS. GENERAL. A.) Overview. 1.) The luminaire shall be a color mixing luminaire employing nine (19) homogenized red, green, blue, and white LED engines.
More informationOwner's Manual. TOUCH SCREEN CONTROLLER for Air Conditioning Control System. Model BMS-CT5120UL. English
TOUCH SCREEN CONTROLLER for Air Conditioning Control System Model BMS-CT5120UL English Contents 1 Precautions for safety.................................................. 5 2 Main functions........................................................
More informationWe put you first. And keep you ahead. USES FEATURES. Bulletin SS09040 Issue/Rev. 0.2 (10/14)
SPECIFICATIONS / INSTALLATION / OPERATION MEASUREMENT SOLUTIONS MMRT Bulletin SS09040 Issue/Rev. 0.2 (10/14) We put you first. And keep you ahead. Smith Meter TOTALIZER/RATE METER The MMRT is a combination
More informationRevision. Decentralized Drive and Positioning Controller MOVIPRO SDC * _1114*
Drive Technology \ Drive Automation \ System Integration \ Services *21341796_1114* Revision Decentralized Drive and Positioning Controller MOVIPRO SDC Edition 11/2014 21341796/EN SEW-EURODRIVE Driving
More informationIVOS II & CEROS II Featuring Next Generation Human Clinical II Sperm Motility Software
HAMILTON THORNE IVOS II & CEROS II Featuring Next Generation Human Clinical II Sperm Motility Software Currently undergoing conformity assessment. Proven & Trusted Sperm Analysis With the proven performance
More information3200NT System 14. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference
3200NT System 14 Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference Table of Contents Job Specification Sheet... 3 Timer Operation... 4 System Operation In Service...
More informationFunctions and Features: Prime key for fast filling and emptying.
P Basic BT501J BT1002J BT3002J BT501J, 0.005-10mL/min Acceptable pump heads are JY10 & D61x. The pump provides flow rates from 0.005 to 10mL/min. It can realize speed adjusting and direction changing and
More informationAltman Lighting AP-150 RGBW Par Specification
1.01 COLOR MIXING LED WASH FIXTURE A. General 1. The fixture shall be Red, Green, Blue, and White LED luminaire with motorized zoom and DMX control. The fixture shall be the AP-150 RGBW by Altman Stage
More information9.5 Add or Remove Samples in Single Access Mode
3. Press the Previous or Next button to see the details of the previous or next loaded position. 4. Press the Back button to return to the information screen. The previous menu is displayed. 9.5 Add or
More information843-R 843-R LASER POWER METER USER MANUAL. NEWPORT CORPORATION
843-R 843-R LASER POWER METER USER MANUAL NEWPORT CORPORATION www.newport.com Table of Contents Chapter 1.Introduction: How to Use This Manual. 3 Chapter 2.Quick Reference... 4 2.1 Getting Started... 4
More informationmedlab One Channel ECG OEM Module EG 01000
medlab One Channel ECG OEM Module EG 01000 Technical Manual Copyright Medlab 2012 Version 2.4 11.06.2012 1 Version 2.4 11.06.2012 Revision: 2.0 Completely revised the document 03.10.2007 2.1 Corrected
More informationOperating instructions Electronic preset counter Type series 717
Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range
More informationHOME GUARD USER MANUAL
HOME GUARD USER MANUAL CONTENTS 1. SAFETY PRECAUTIONS...2 2. INTRODUCTION...3 3. FEATURES...4 4. ACCESSORIES...5 5. INSTALLATION...6 6. NAME and FUNCTION of EACH PART...7 6.1 Front Pannel...7 6.2 Monitoring
More informationVENUS X1PRO-E Quick Start
VENUS X1PRO-E Quick Start 4K input support in DP, HDMI and Dual Link DVI Support 8K x 1K, 4K x 2K Seamless Splicing EDID management Modular 2K input: Three slots for 2K input options 2K-2K and/or 4K-2K
More informationInstalling the FOREST SHUTTLE S / L
2 Installing the FOREST SHUTTLE S / L 1 Assemble the track 2 Install the brackets and fix the track onto the brackets 3 Do not attach the drapery yet. Attach the drapery only after the end positions have
More informationThe FAIR plinac RF Systems
The FAIR plinac RF Systems Libera Workshop Sep. 2011 Gerald Schreiber Gerald Schreiber, GSI RF Department 2 (1) Overview GSI / FAIR (2) FAIR Proton Linear Accelerator "plinac" (3) plinac RF Systems (4)
More informationMonitorKey Operation Manual: content/uploads/ MonitorKey Operation Manual.pdf
Additional Resources: MonitorKey Operation Manual: www.editraffic.com/wp content/uploads/888 1212 001 MonitorKey Operation Manual.pdf CMUip 2212 Operation Manual: www.editraffic.com/wp content/uploads/888
More informationDigital Adapter Easy Setup Guide. Installation Operation Troubleshooting
Digital Adapter Easy Setup Guide Installation Operation Troubleshooting Table of Contents What s included in this Install Kit? 4 Connecting to a TVwith HDMI Cable 8 Connecting to a TV with Coax Cable 9
More informationField Test Procedure for Sentry. 1 Purpose Applicable documents Procedure Duration - Time Estimate... 2
Title: File : 50053-1B--FIELD-TEST.DOCX Field Test Procedure for Sentry Page: 1 of 37 Table of Contents: 1 Purpose... 2 2 Applicable documents... 2 3 Procedure Duration - Time Estimate... 2 3.1 10048 (ARM&12CHBriteSpot)...
More informationQuick Reference Guide
Quick Reference Guide Wireless Video Intercom System Model No. VL-SWH70 series Video Intercom System with Wireless Sensor Camera/ Video Intercom System Model No. VL-SVH70 series Door Station (Doorphone)
More informationSTIMULUS CONTROLLER, Type CS-55 INSTRUCTIONS
, Type INSTRUCTIONS 2015 Reproduction of text and/or drawings is permitted for personal use. The use of reproductions in publications is only allowed if correct reference is made to 1 2 3 6 7 4 5 8 9
More informationClick Here To Start Demo
Click Here To Start Demo AirLogix Demo Title Screen AirLogix Interactive Demonstrator Version 3.0 Copyright 2005 by Case Engineering inc This is intended as a working active demonstration only. Every attempt
More informationEASY-MCS. Multichannel Scaler. Profiling Counting Rates up to 150 MHz with 15 ppm Time Resolution.
Multichannel Scaler Profiling Counting Rates up to 150 MHz with 15 ppm Time Resolution. The ideal solution for: Time-resolved single-photon counting Phosphorescence lifetime spectrometry Atmospheric and
More informationTimeView Display. Operating Manual
TimeView Display Operating Manual 9520-647 Airborne Serial Time Display CHAPTER ONE Introduction/Product Overview 4 Operating Manual Summary 5 Purpose of Equipment 5 Preparation for Shipment 6 Typographical
More informationStimulus System of Shielded Room (DC)
Author, date: Veli-Matti Saarinen, 19.1.2017 Introduction to of the Shielded Room (DC) Stimulus System of Shielded Room (DC) This manual is to provide basic information to work with the stimulus system
More informationVariwrap Controller Manual
Variwrap Controller Manual Operation The controller has two operating modes Manual and Auto. The mode is changes by pressing the (F1) Auto/Manual button. The mode setting is displayed in the top right
More informationZ-IP Stream 004/008. User Guide and Installation Manual. Four or Eight Input QAM Encoder / Modulator
Z-IP Stream 004/008 User Guide and Installation Manual Four or Eight Input QAM Encoder / Modulator MPEG-2 / H.264 HD ENCODER with QAM /IP/ & ASI Outputs Contents Safety Precautions... 3 Package Contents...
More information