For 8-UB ( XXXXXX) + 8-RB ( XXXXXX) + 8-CT ( XXXXXX) + 8-G ( XXXXXX) + 8-FC ( XXXXXX) + 8-VS ( XXXXXX):
|
|
- Cody Donald Cox
- 5 years ago
- Views:
Transcription
1 STB/CAB INSTALL INSTRUCTIONS Applies to: All 8-Series Cardio w/15 STB-Ready Console For 8-UB ( XXXXXX) + 8-RB ( XXXXXX) + 8-CT ( XXXXXX) + 8-G ( XXXXXX) + 8-FC ( XXXXXX) + 8-VS ( XXXXXX): Latest Rev. Tools Required: #2 Phillips Screwdriver 1. Using a phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable inlets securing internal cables to the electrical plate. NOTE: Please note that the instructions given on Pages 1-4 are valid for ALL UNITS, a Recumbent Bike is only shown as an example. For STB/CAB install on all other units, please see below: 8-RDE Rear Drive Elliptical (Pg. 5) Treadmills (Pg. 8) 8-FC FreeClimber (Pg. 10). Page 1
2 2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is routed down through the machine XXXXXX (8-CT) XXXXXX (8-G) XXXXXX (8-CT) XXXXXX (8-CT) XXXXXX (8-VS) XXXXXX (8-FC) Page 2
3 3. Install the HDMI grommet onto the HDMI cable and the 90 degree RJ45 adapter onto the CSAFE cable. 4. Pass the HDMI cable through the bottom opening of the new electrical plate pulling the grommet through the plate to secure it. Also install the 90 degree RJ45 adapter by passing it through the top hole in the electrical plate and clicking it into place. Finally, secure the electrical plate to the frame using two (2) of the supplied screws. Use the cable retention clamps as shown to secure any loose wires. Page 3
4 5. Connect the CSAFE and HDMI cables running up to the 15 Embedded console to their respective connections. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right). Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below. 6. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB*. *Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit. TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12. Page 4
5 For 8-RDE ( XXXXXX): Tools Required: #2 Phillips Screwdriver 1. Using a phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable inlets securing internal cables to the electrical plate. 2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing path is represented by the dark bold line below (Fig. 7). Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is routed down through the machine. Page 5
6 3. Install the 90 degree RJ45 adapter onto the CSAFE cable and push the adapter into the plate so it clicks into place. Next, pass the HDMI cable through the cutout in the new electrical plate shown below. 4. Use two (2) of the supplied screws to install the HDMI cable retention plate. Finally, use two (2) of the supplied screws to finish securing the new electrical plate to the frame, use the cable retention clamps as shown to secure any loose wires. Page 6
7 5. Connect the CSAFE and HDMI cables running up to the 15 Embedded console to their respective connections. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right). Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below. 6. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB* *Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit. TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12. Page 7
8 For Treadmills ( XXXXXX XXXXXX XXXXXX): Tools Required: #2 Phillips Screwdriver 1. Route HDMI cable down through mast of machine and out through the hole in the frame. The routing path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is routed down through the machine. 2. Route the end of the HDMI cable out of the bottom of the treadmill frame where shown below. Use the cable retention clamps to secure any loose wires. Page 8
9 3. Connect the CSAFE and HDMI cables running up to the 15 Embedded console to their respective connections. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right). Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below. 4. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB* *Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit. TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12. Page 9
10 For FreeClimber ( XXXXXX): Tools Required: #2 Phillips Screwdriver 1. Route HDMI cable down through mast of machine and out through the hole in the frame (please note that the user right side shroud has been removed for clarity. The routing path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is routed down through the machine. 2. Route the end of the HDMI cable out of the bottom of the FreeClimber frame where shown below. Use the cable retention clamps to secure any loose wires. Page 10
11 3. Connect the CSAFE and HDMI cables running up to the 15 Embedded console to their respective connections. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right). Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below. 4. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB* *Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit. TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12. Page 11
12 Installing the IR Emitter: OPTION A: If the set top box (STB) is located close to the unit, the IR emitter can be connected directly into the RJ45-to-3.5mm as shown below: OPTION B: If the set top box (STB) is located farther away from the unit, such as inside an A/V closet, the adapters can be combined with a length of customer-supplied CAT6 cable in order for the IR emitter to reach the STB: Page 12
13 Mounting the IR Emitter: Once the 3.5mm end of the IR cable has installed into the CAB using either Option A or Option B (see page 15), the IR diode end of the IR emitter will need to be attached to the front of the STB where the IR receiver is located. If you cannot locate the IR receiver on the STB, shining a flashlight at the front of the STB can help in locating it. In the examples above, you can see the IR emitter mounted to the STB over the STB s IR receiver. The two examples on the left show common locations of the IR receiver on two STBs. Once the IR diode is in place, install the IR shield onto the front of the IR diode (Fig. 17). This will ensure that the signal sent to the STB will only change the settings on the STB that the IR diode has been applied to. Page 13
STB/CAB INSTALL INSTRUCTIONS
STB/CAB INSTALL INSTRUCTIONS 8-Series STB-Ready 15 Embedded Consoles Tools Required: - Phillips Screwdriver For 8-UB (9-8120-XXXXXX) / 8-RB (9-8130-XXXXXX) / 8-CT (9-6140-XXXXXX) / 8-G (9-5250-XXXXXX)
More informationYour CAB is enabled for an application as follows:
CAB Console Adapter Box CAB s for use with attachable personal viewing Screens from BVE, Life Fitness, Precor, Mye, Freemotion, Matrix, Octane, Startrac and others operated from cardio equipment console
More informationOnline Service Manuals available at:
CAB PRECOR P80 The Precor P80 console with the media adapter kit can now control ANY cable, satellite or IPTV set top box using the CAB from Broadcastvision Entertainment. Online Service Manuals available
More informationCAB OCTANE. Online Service Manuals available at:
CAB OCTANE The new fully integrated personal viewing screen from Octane can now control ANY cable, satellite or IPTV set top box using the CAB from Broadcastvision Entertainment. Online Service Manuals
More informationCAB CYBEX For use with BVE personal viewing screens operated from Cybex 525 or 625 series consoles
CAB CYBEX For use with BVE personal viewing screens operated from Cybex 525 or 625 series consoles The dynamic Broadcastvision Entertainment AXSCAB accommodates many varied applications to allow console
More informationCAB INTENZA. BVE Technical Support Tel: x 3
CAB INTENZA The Intenza E2 console can now control ANY cable, satellite or IPTV set top box using the CAB from Broadcastvision Entertainment. Benefits: Eliminates the hand-held battery operated remote
More informationCAB MATRIX 7xe/7xi. Online Service Manuals available at:
CAB MATRIX 7xe/7xi The Matrix 7xe and 7xi consoles can now control ANY cable, satellite or IPTV set top box using the CAB from Broadcastvision Entertainment. Online Service Manuals available at: www.broadcastvision.com
More informationCAB (Core/Matrix/Mye/Precor)
CAB (Core/Matrix/Mye/Precor) The following manual includes instructions for installing the BroadcastVision CAB for use on the Core/Matrix/Mye/Precor Screens with a CableSat jack connection. Online Service
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More information1.1 Introduction Getting Connected Guide - Wireless Setting up a Wireless Network Getting Connected Guide - Wired...
PCTV SERVICE MANUAL Introduction CHAPTER 1: INTRODUCTION 1.1 Introduction...1 CHAPTER 2: NETWORK CONFIGURATION & SETUP 2.1 Getting Connected Guide - Wireless...3 2.2 Setting up a Wireless Network...5 2.3
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More information(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS
(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS E-UB Upright Bike 4 620-7922 Rev B GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual;
More information2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU
2000 Series Weather Stations Analog Temperature / RH Sensor Upgrade Kit PRODUCT MANUAL KIT # 3613WDU 1 The 3613WDU Analog Temperature / RH Sensor Upgrade Kit is used to upgrade Watchdog 2000 Series Weather
More informationDISCOVER SE: 19 INCH LCD TREADMILL CONSOLE
DISCOVER SE: 19 INCH LCD TREADMILL CONSOLE PARTS MANUAL 19DT-XXXXX-XX EAT, EPT, EDT, EIT, ENT, EST, FAT, FPT, FDT, FIT, FXT, FST October 2018 Table of Contents Console Table 1 Common Boards for Consoles
More informationGENUINE PARTS CAUTION
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SATELLITE RADIO SYSTEM 2. PART NUMBERS: XM tuner kit 999U9-NV003 XM antenna kit 999U9-VR000 Sirius tuner kit 999U9-NV004 Sirius antenna
More informationDLMP Installation Instructions
DLMP Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420 [ ] 2 x
More informationDISCOVER SE: 16 INCH LCD BIKE & CROSS-TRAINER CONSOLE
DISCOVER SE: 16 INCH LCD BIKE & CROSS-TRAINER CONSOLE PARTS MANUAL 16DN-XXXXX-XX, EPN, EDN,, ENN, ESN, FAN, FPN, FDN, FIN,FXN, FSN January 2017 Table of Contents Console Table 1 Common Boards for Consoles
More information24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual
24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number
More informationINSTALLATION INSTRUCTIONS WIRED REMOTE CONTROL USING COAX CABLE U-WRC-C
Tel-Quip PH: 713-728-0625; FAX: 713-456-2512 www.telquip.com INSTALLATION INSTRUCTIONS 10-17-2013 WIRED REMOTE CONTROL USING COAX CABLE U-WRC-C Thank you for using the Tel-Quip Wired Remote Control. This
More informationINSTALLATION INSTRUCTIONS WIRED REMOTE CONTROL USING TWISTED PAIR AND COAX CABLE U-WRC-U-x
Tel-Quip PH: 713-728-0625; FAX: 713-456-2512 800-317-0847 (Toll Free) www.telquipstore.com INSTALLATION INSTRUCTIONS 10-17-2013 WIRED REMOTE CONTROL USING TWISTED PAIR AND COAX CABLE U-WRC-U-x Thank you
More informationHDMI Extender over HDBaseT
User s Manual HDMI Extender over HDBaseT With Ultra-HD AV, IR, RS232 Control, and Ethernet over a single Cat6 Cable Part Number HBX HBX-S HBX-R Function HDMI + RS-232 + IR + Ethernet Extender Kit * Includes
More informationCabling and Completing Assembly of the Cisco TelePresence System 1000
CHAPTER 5 Cabling and Completing Assembly of the Cisco TelePresence System 1000 Revised: April 5, 2010, Introduction This chapter describes how to set up and connect the cables, microphone and Cisco Unified
More informationExtender for HDMI. gefentoolbox.com GTB-HDBT-POL GTB-HDBT-POL-BLK. User Manual
Extender for HDMI w/pol GTB-HDBT-POL GTB-HDBT-POL-BLK User Manual gefentoolbox.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out of the box. Hold it by its edges only. If you touch the screen, you can cause the TV panel to crack. Included
More informationNEW. Datasheet. Field wiring Cabtite Easy Cable Entry System!
Datasheet Field wiring Cabtite Easy Cable Entry System! NEW Do you really need a plug-in connector on the out-side of your switchgear cabinet? Or do you simply just want to make connections? Now you can
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationOptical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
More informationTeamWork Kits Installation Guide
TX 0 RX COM +5V APARATUS US TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables
More informationUAV Ultimate Atari Video A7800
UAV Ultimate Atari Video A7800 Basic Install guide because this is really easy mod to do! The UAV is a wonderful piece of tech for what it can do. To summarize, the UAV is a replacement video encoder and
More informationVIEW Lite DJ100 Digital AV Decoder JPEG2000 Based Audio/Video Decoder. Quick-Start Guide
VIEW Lite DJ100 Digital AV Decoder JPEG2000 Based Audio/Video Decoder Quick-Start Guide Table of Contents PRODUCT OVERVIEW... 1 VIEW Lite AV over IP Streaming System... 1 Device Application... 1 ENCODERS
More informationHDBaseT HDMI Extender over CAT5e/6/7 with IR - 70m
HDBaseT HDMI Extender over CAT5e/6/7 with IR - 70m P/N: HDbaseT-Ext G4-0018A Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have fun
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
MIC TV SEARCH KEYPAD SOURCE VOL VOICE CH RETURN GUIDE EXIT CH.LIST SMART HUB 3D MTS CC P.SIZE MENU INFO 1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Parts in the box Single monitor Dual monitor M2 M8 M/Flex + (package contents will depend on configuration ordered) Tools required for installation 6.0 mm Hex Key
More informationTen-Tec (865) Service Department:(865)
Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram
More informationTV Setup and Troubleshooting
Service Menu TV Setup and Troubleshooting E-TRe & E-TRxe The following procedure will guide you through the Channel Scan of the Embedded E-TRe and E-TRxe treadmills. Step 1 Start on the default screen
More informationUser Manual. HDBaseT Receiver CMHDBTBRX. Front View Panduit Dr, Tinley Park, IL (708)
User Manual HDBaseT Receiver CMHDBTBRX Front View 18900 Panduit Dr, Tinley Park, IL 60487 (708) 532-1800 Back View TABLE OF CONTENTS Introduction 2 Features 3 Package Contents 3 Technical Specifications
More informationExtender for HDMI over one CAT5
1080P Extender for HDMI over one CAT5 GTV-HDBT-CAT5 User Manual gefentv.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours:
More informationDLMP-45/45R Installation Instructions
DLMP-45/45R Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420
More informationInstallation Manual. Multi-Room Distribution Hub.
Installation Manual LN-2400DH Multi-Room Distribution Hub 100310 KIT CONTENTS Multi-Room Distribution Hub Qty: 1 Pc Part Code: LN-2400DH Computer Network Patch Cables Qty: 8 Pcs Part Code: LN-CAT5-0.3BL
More information2x2 HDMI Matrix Switch - 4K with Fast Switching and Auto-Sensing
2x2 HDMI Matrix Switch - 4K with Fast Switching and Auto-Sensing Product ID: VS222HD4K Save time and hassle by automatically switching between your HDMI audio/video sources. This 2x2 HDMI matrix switcher
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BEFORE INSTALLING OR ADJUSTING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY. PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE FIBER OPTIC SWING-OUT PATCH PANEL INSTRUCTION
More informationLINK EXT40-4KECO. 4K 40m HDMI Extender. User Manual. Version: V1.0.1
LINK EXT40-4KECO 4K 40m HDMI Extender User Manual Version: V1.0.1 Important Safety Instructions 1. Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with
More informationCardio Theater xtv900 Receivers Installation and Maintenance Guide
Cardio Theater xtv900 Receivers Installation and Maintenance Guide MUTE VOL ENTERTAINMENT CONTROLS CH ch vol mute Important Safety Instructions Always follow basic safety precautions when using this equipment
More informationTeamWork Installation Guide
C G G 00-0V/ A MAX TX RX +V APARATUS US 0 TeamWork Installation Guide TeamWork TeamWork is a fully customizable collaboration system comprised of an switcher, Show Me cables, a control processor, and a
More informationIP-LINX. Installation Guide
Installation Guide Installation Guide, 146653-4 Copyright 2017, Telect, Inc. All Rights Reserved Telect and Connecting the Future are registered trademarks of Telect, Inc. 22425 East Appleway Ave. # 11
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More information2-Port HDMI Automatic Video Switch - 4K with Fast Switching
2-Port HDMI Automatic Video Switch - 4K with Fast Switching Product ID: VS221HD4KA Create a powerful visual experience, with the ability to switch between two 4K video sources seamlessly. This 2-port HDMI
More informationIP-LINX Fiber :: X-XXXX
Fiber :: 055-797X-XXXX User Manual Telect, Inc. All rights reserved. 146653-A0 Table of Contents Chapter 1: Introduction...3 1.1 Tools Required...3 1.2 Additional Parts...3 1.3 Assemblies...3 Chapter 2:
More informationIntroduction. Introduction
Introduction Introduction Note: In this user guide Pronto is used for both ProntoPro and Pronto remote controls. RFX6000 is compatible with TSU3000 and TSU6000. About the RFX6000 Most remote control systems
More informationQUICK INSTALLATION GUIDE
V1.1.1/2018 homeit.io All rights reserved Index NR. CHAPTER PAGE 1 Introduction 2 1.1 The homeit System 2 2 Equipment and materials 3 2.1 The homeit KIT 3 2.2 Tools & Supplies 4 3 Location of the homeit
More informationHi! Let s get started.
Hi! Let s get started. 55US5800 What s in the box TL Roku TV TV stands Power cable 4 x TV stand screws (ST4X20mm) 2 x AAA batteries for remote TV remote What you need Make the most of your Smart TV Phillips
More informationCable harness for bodywork functions
General information General information This document describes 2 different cable harnesses for bodywork functions, see illustration. C486 C487 C488 C494. Cable harness from cab to frame (variant family
More informationFeatures: Model : ATZ HDBT-E70-RB Description : HDBaseT Extender Receiver Box for HMDI w/ir+pol (70m)
The ATZ HDBT-E70-RB is part of ATZ s expanding Multi Video HDBaseT Cat Extender. Single side connections for HDMI, Control, and Power provide a cleaner wiring and rack mounting solution. The design allows
More informationMitsubishi WD57734 DLP Chip Replacement
Mitsubishi WD57734 DLP Chip Replacement Replace the DLP chip in your Mitsubishi WD57734. Written By: David Sylvester ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION This guide will detail the
More informationMRF-300/RFX150 INSTALLATION MANUAL
MRF-300/RFX150 INSTALLATION MANUAL TM Multi-Zone RF Base Station for the MX-3000, the Aurora, TM TM TM the Aeros, the Omega and the Osiris remote controls. MRF-300 Installation Manual 2005 Universal Remote
More informationTechnical Information Bulletin
June 4, 2001 #TIB0003 Units Affected: Model Serial Numbers Model Serial Numbers SVT-2PRO T2PDxxxxxxxxx SVTAV AXVDxxxxxxxxx ATLDxxxxxxxxx BJIDMAxxxxxxx SVT-2PROJ T2PJxxxxxxxxx SVTAVJ BAHJxxxxxxxxx ATLJxxxxxxxxx
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version October 5, 2016 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE TERMINAL...6
More informationStar Trac Fitness PERSONAL VIEWINGS SCREEN OWNER S MANUAL
Star Trac Fitness PERSONAL VIEWINGS SCREEN OWNER S MANUAL TABLE OF CONTENTS Introduction....................................................... 4 Before You Get Started..............................................
More informationLCS 2 RJ 45 Cat. 6A HD panels and units
87045 LIMOGES Cedex Telephone: (+33) 05 55 06 87 87 - Fax: +33 (0)5 55 06 88 88 Page 0 335 85/86 1. General characteristics....1 2. Presentation...1 3. Positioning...1 4. Technical characteristics...1
More informationAssembly instructions
Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0)1553 811000 Email: support@maxview.co.uk Web: www.maxview.co.uk Maxview reserve the right to change specifications
More informationCH-1605RXV 4K UHD+ HDMI over HDBaseT 2.0 Receiver (PD) with HDR/ARC
CH-1605RXV 4K UHD+ HDMI over HDBaseT 2.0 Receiver (PD) with HDR/ARC Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology
More informationHDBASE100ME. HDBaseT 100M Extender with 2-Port Ethernet Switch. Extend Ultra HD 4K, Multi-channel Audio, Ethernet & IR over a single Cat 6 cable
HDBaseT 100M Extender with 2-Port Ethernet Switch Extend Ultra HD 4K, Multi-channel Audio, Ethernet & IR over a single Cat 6 cable TABLE OF CONTENTS 1. Introduction... 1 1.1 Introduction to HDBASE100ME...
More informationMagelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide
Magelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide Thank you for purchasing the XBT ZG43 replacement backlight. Be sure to read the following Backlight Replacement Instruction bulletin prior
More information4X4 HDMI SWITCHER: 4 SOURCES TO 4 DISPLAYS 4X1 HDMI SWITCHER: 4 SOURCES TO 1 DISPLAY. dealer 2: $ export 1: $ export 2: $ Features.
4X4 HDMI SWITCHER: 4 SOURCES TO 4 DISPLAYS resolutions up to 1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved 4X1 HDMI SWITCHER: 4 SOURCES TO 1 DISPLAY 60W max. (included) (includes
More informationHDBaseT HDMI Extender
over Single Cat 6 up to 330 Feet Model 103078 Supports 100BaseT Uncompressed Video and Surround Sound Audio User Manual Table of Contents 1. INTRODUCTION... 1 1.1 Introduction 1.2 Copyright and Trademarks
More informationPassive UTP Transceiver Hub with Integral Camera Power Installation Guide
Passive UTP Transceiver Hub with Integral Installation Guide Models Include: HubSat8D - Eight (8) Channels HubSat82D - HubSat8D w/eight (8) HubWayAv Balun/s for s HubSat83D - HubSat8D w/eight (8) HubWayDv
More informationEdition 1, August 2011 Copyright 2011 Smart-e (UK) Ltd.
Notice The information contained in this document is subject to change without notice. Smart-e makes no warranty of any kind with regard to this material, including but not limited to, implied warranties
More informationSY-HDBT-100 Extender Set
Installation Guide SY-HDBT-100 Extender Set with HDMI, IR, RS232 and Ethernet over 100m of cat6 Cable HDBaseT HDMI Extenders SY Electronics Ltd, Unit 7, Worrall Street, Salford, Greater Manchester, M5
More informationKAT5.tv AV Distribution System. KAT5 AVRX User Guide
KAT5 AVRX Mk2 AV Receiver User Guide Version 1.0 1 st August 2005 Overview The KAT5 AVRX is a device that receives electronically balanced AV signals over a CAT5 Structured Wiring Scheme Used with the
More informationCH-2605TXV 4K UHD+ HDMI over HDBaseT 2.0 Transmitter (PD) with HDR/ARC
CH-2605TXV 4K UHD+ HDMI over HDBaseT 2.0 Transmitter (PD) with HDR/ARC Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology
More informationUnity Home System. UnIty/Unity Home System. Video Q-Link ports allow direct connections of up to two Selective Call Video Door Units
Unity Home System The Unity Home System seamlessly integrates On-Q Camera, Multi-Room Audio, and Selective Call Intercom functions into one robust home system that is easily controlled via an attractive
More information1 Unpack. Taking the TV Out of the Box. Included in this Box. Stand Parts and Cables. Remote Control. Also included
MIC TV SEARCH KEYPAD SOURCE VOL VOICE CH RETURN GUIDE EXIT CH.LIST SMART HUB 3D MTS CC P.SIZE MENU INFO 1 Unpack Taking the TV Out of the Box Warning: Do not touch the TV s screen when you take it out
More informationHDMI over IP EXTENDER
HDMI over IP EXTENDER Manual DS-55200 DS-55201 1. Introduction Thanks for purchasing the DS-55200 HDMI over IP Extender (DS-55201 receiver only). We recommend that you read this manual thoroughly and retain
More informationCAT System on the MIC socket for Yaesu FT-897/857
CAT System on the MIC socket for Yaesu FT-897/857 (it doesn't apply to the FT-817) By Filippo Tondinelli, IZØINX When an automatic tuner like the Yaesu CF-30 is used with a Yaesu FT-897 or FT-857, it will
More informationHD Video Distribution
4X4 HDMI SWITCHER: 4 SOURCES TO 4 DISPLAYS Distributes any of the four inputs to any or any combination of the four HDMI output displays Maintains high resolution video - beautiful, sharp HDTV resolutions
More informationPowerWave PW1A Panel and Wall-Mount Models Installation Guide AV69006-XXX
PowerWave PW1A Panel and Wall-Mount Models Installation Guide 8820-00063 AV69006-XXX Table of Contents Table of Contents sections 1 2 3 4 5 6 7 8 9 1. Introduction............................................
More informationguestlink PowerWave PW4A Panel and Wall-Mount Models Installation Guide AV69102-XXX-XXX
guestlink PowerWave PW4A Panel and Wall-Mount Models Installation Guide 8820-00291 AV69102-XXX-XXX Table of Contents Table of Contents sections 1 2 3 4 5 6 7 8 9 1. Introduction............................................
More informationGENUINE PARTS. N-Bus harness for ipod Gateway 999U7-VS000 N-Bus harness for [optional] SAT Radio 999U7-VS001 FRONTIER, PATHFINDER & XTERRA (2005~)
GENUINE PARTS ipod INSTALLATION INSTRUCTIONS. DESCRIPTION: ipod 2. PART NUMBERS: ipod Gateway Module Kit 999U7-VR000 N-Bus harness for ipod Gateway 999U7-VS000 N-Bus harness for [optional] SAT Radio 999U7-VS00
More informationCaution. Hanging the Screen:
Installation Instructions for Laminar and Laminar XL Projection Screens Caution 1. Read Instructions through completely before proceeding; keep them for future reference. Follow these instructions carefully.
More informationPI MANUFACTURING Powered by Infinite Solutions
PI MANUFACTURING Mfg Number: PD36575 Part Number: HDMI-VWALL-KIT Features: Takes one HDMI source and divides it into 4 displays in a 2x2 configuration to make a large video wall 2x2 HDMI Video Wall Controller
More informationapple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema HD Display 23" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema HD Display 23" LCD (ADC) 2003 Apple
More informationOPERATIONAL MANUAL EMZS CH Speaker Zone Selector. Version 1.6
OPERATIONAL MANUAL EMZS-8012 12CH Speaker Zone Selector Version 1.6 1 Product Overview The EMZS-8012 is a 1U rack-mounting unit, provide 12 channel direct zone switching for single source public address
More informationInstalling a Personal Viewing System (PVS)
Installing a Personal Viewing System (PVS) Including Models with Personal Entertainment Player (PEP) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Installing a
More informationCovid HDBase-T Receiver for HDMI with Built in Audio de-embedding, IR, and RS232 control pass through
Covid HDBase-T Receiver for HDMI with Built in Audio de-embedding, IR, and RS232 control pass through Contents Introduction...2 Package Contents...2 Key Features...2 Panel Description...3 Connection and
More informationLGX Compatible (LSX) Connector Module) User Manual)
LGX Compatible (LSX) Connector Module) User Manual) 15948-A LSX Connector Module (72-Position Module Shown) Content Page 1 DESCRIPTION... 3 2 DIMENSIONS AND SPECIFICATIONS... 5 3 INSTALLATION... 6 3.1
More informationVGA CAT-5 1:8 Distribution S VGA CAT-5 Distribution R
VGA CAT-5 1:8 Distribution S VGA CAT-5 Distribution R EXT-VGA-CAT5-148S EXT-VGA-CAT5-148R User Manual www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax
More informationDirect-Connect DVI Cables
Direct-Connect DVI Cables Shielded for maximum EMI/RFI protection Dual-link resolutions/bandwidth up to 2560 x 1600 / 9.9 Gbps Single-link resolutions/bandwidth up to 1920 x 1080 / 4.95 Gbps P560-xxx Series
More informationPassive UTP Transceiver Hub with Integral Camera Power Installation Guide
Passive UTP Transceiver Hub with Integral Installation Guide Models Include: HubSat4D - Four (4) Channel Passive UTP Transceiver Hub with Integral HubSat42D - Four (4) Channel Passive UTP Transceiver includes
More informationManual #: UMA1074 Rev. 2 October, Hall Research Technologies, Inc 1163 Warner Ave. Tustin, CA 92780
Component Video / VGA Over UTP Video Transmission Systems Manual #: UMA1074 Rev. 2 October, 2007 Hall Research Technologies, Inc 1163 Warner Ave. Tustin, CA 92780 Table of Contents 1.0 GENERAL DESCRIPTION...
More informationIn-Wall Control Mount for ipod Touch
In-Wall Control Mount for ipod Touch INTRODUCTION The Mirage KP-iOS is an in-wall system that allows ipod touch (4th generation) to become a semi-permanent fixture in your wall. The system allows you to
More informationIntegrator s Guide Concord
Integrator s Guide Concord HD Component Video / Composite Video / Analog Audio Matrix Switch with Cat5 outputs 2 3 Table of Contents Table of Contents... 3 Introduction... 4 Features:... 4 Installation...
More informationKramer Electronics, Ltd. USER MANUAL. Wall Plate Models: SV-301 SV-302 SV-303 SV-304 SV-305
Kramer Electronics, Ltd. USER MANUAL Wall Plate Models: SV-301 SV-302 SV-303 SV-304 SV-305 Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Defining the Wall Plates (for the United
More informationART2000i Digital Dimming System. Installation guide. Stock number *8200-
ART2000i Digital Dimming System Installation guide Stock number 8200-0159 *8200- 0159* Useful Avolites phone numbers:- Avolites England Sales and service* (+44) (0) 20 8965 8522 Service out of hours* (+44)
More informationKIT INSTRUCTIONS. Checkstand Display Mount K039 Issue C
KIT INSTRUCTIONS Checkstand Display Mount 5968-K039 Issue C The product described in this book is a licensed product of NCR Corporation. NCR is a registered trademark of NCR Corporation. NCR RealPOS is
More information1x12 VGA & Audio over CAT5 Splitter
SP-9112 1x12 VGA & Audio over CAT5 Splitter User Manual rev: 160322 Made in Taiwan Safety and Notice The SP-9112 1x12 VGA & Audio over CAT5 Splitter has been tested for conformance to safety regulations
More informationPower Injector 1520 Series
Power Injector 1520 Series Technical Specifications Input voltage 100 to 240 VAC Output voltage 56.0 VDC Voltage range tolerance 54 VDC to 57 VDC Maximum current 1.43 A No load current 15 ma 56VDC@0.71A
More informationMulti-Input to HDMI Automatic Switch and Converter - 4K
Multi-Input to HDMI Automatic Switch and Converter - 4K Product ID: HDVGADP2HD This multi-input converter switch lets you connect your DisplayPort (DP), HDMI and VGA audio/video sources to one HDMI display
More informationSTAR TRAC FITNESS TM PERSONAL VIEWING SCREEN O WNER S M ANUAL
STAR TRAC FITNESS TM PERSONAL VIEWING SCREEN O WNER S M ANUAL TABLE OF CONTENTS Introduction...................................................................................... 4 About This Manual.........................................................................
More informationMONOPRICE. Blackbird 4K HDBaseT Extender Kit. User's Manual P/N 21792
MONOPRICE Blackbird 4K HDBaseT Extender Kit P/N 21792 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings
More informationTV Lift System Model CL-65 Installation Instructions
TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing
More information