PB2ZMRF/2 APRIL 2013 EFFECTIVE: 1ST APRIL Zone RF Master Unit. User Guide PB2ZM RF

Transcription

1 PB2ZMRF/2 APRIL Zone RF Master Unit EFFECTIVE: 1ST APRIL 2013 User Guide PB2ZM RF April 2013

2 CONTENTS Overview Setting Up Guide Full Master System Reset Technical Specification

3 OVERVIEW The latest range of Polypipe s Radio Frequency central heating controls offer a quick and easy option for both new and retrofit installations. The following guide will take you through the simple step by step process for setting up your new RF controls system. Before you commence the setting up process please be sure to have your RF Thermostat and Four Channel Timer technical installation guides to hand as these will provide you with the necessary information required to complete the RF initialisation set-up between the room thermostat units, four channel timer and the RF master and slave units. In order to ensure that the best RF signal is transmitted and received the remote antenna unit as supplied should be positioned in a vertical plane and at least 50cm away from any other electrical outlet or any metallic pipe work. 03

4 First ensure that the wiring unit is correctly wired up to the electrical system in accordance with the instructions as given in the installation manual as supplied with the PB2ZM RF. Switch on the power to the unit and the green power LED should illuminate. Pairing The RF Thermostats (PBDIG RF PBRS RF & PBPRPS RF) 1) Press and hold the OK button for approximately 10 seconds and the first green LED will illuminate (flashing). 2) Press the OK button again quickly and the first LED will turn Red to show that the first zone is ready to be paired with the relevant room thermostat. At the same time the second LED will flash green. 04

5 3) Pair the first thermostat by following the procedure as shown in the installation guide as supplied with the RF thermostat units Once the pairing signal has been accepted the first LED will become solid green. At this point it is important to remember to then switch this thermostat to the OFF mode so as to prevent its wireless signal from interfering with any further pairing process. 5) Pairing the Time Clock: Where the PBDIG RF or PBRS RF units have been used it is necessary to now pair the relevant timer channel on the PB4CTC RF timer unit to the master wiring centre. To do this you will need to access the Installer Menu in the timer unit by following the instructions as supplied with the unit. Once you have chosen the required channel to be used and have initialised the pairing function all of the Green LED s will switch off inside the master unit and slave unit to indicate that the pairing of the time clock has been successful. Please note that no actions are necessary to the master wiring centre. 4) Press the OK button again quickly and the second LED will now flash Red indicating that the second zone is ready to be paired. Follow the same pairing process for this zone as previously explained. Once the time clock and room thermostats have been switched to the required operating mode the system should now respond accordingly. At this stage the PB2ZM RF unit will now be paired to the two thermostatic zones. If an additional RF Slave Unit is to be used continue to follow the above procedure until all of the remaining zones have also been paired. Additional Information: To toggle between zones to be paired please use the left and right arrow buttons. IMPORTANT NOTE: At this stage the thermostat units will now be paired to their relevant master wiring centre and slave unit zones (if used). In the case of the PBPRPS RF fully programmable units where no additional timer unit is to be used it is necessary to now complete the pairing process by pressing and holding the OK button until all of the LED s go out. Once this happens the pairing process is now complete and the zones should respond to the relevant demand signals from thermostat unit/s. Performing a Full Factory Reset: Sometimes it may become necessary to return the master wiring unit and slave unit (if fitted) to their factory resets. This action will completely erase any current pairing information and enable the units to be fully reprogrammed. To do this press and hold down all three of the buttons on the side of the master unit until both green LED s are illuminated. During this process if only one of the LED s illuminates you will need to first release the three buttons and then press them again until both LED s are lit. Once this happens keep the buttons depressed until both LED s switch off and then quickly release the buttons. After a few seconds both LED s will flash Green once and then switch off again. The unit/s are now fully reset. 05

6 User Guide PB2ZM RF 2 Zone RF Master Unit Polypipe Building Products Broomhouse Lane Edlington Doncaster DN12 1ES Tel: +44 (0) Fax: +44 (0) London Road Mount Vernon Glasgow G32 8XZ Tel: +44 (0) Fax: +44 (0) Dromore Road Lurgan, Craigavon Co. Armagh BT66 7HL Tel: Fax: Underfloor heating systems trade website: ufch.com Underfloor heating systems consumer website: homesolutions.polypipe.com