ADF Module. Installation Guide. 1.1 Overview

Transcription

1 ADF Module Installation Guide 1.1 Overview The installation sheet is divided into three sections. Section 1.2 Description on page 2 describes the areas on the frame and modules dedicated to the mounting of the modules to the frame. Section 1.3 Installation on page 5 provides a step by step procedure for mounting the modules. Modules are marked L and R for installation on the left and right side of the frame. See Asssembly Parts on page 4 for a larger view of the areas on the frame. Installation requires #2 and #3 Phillips head screwdrivers. Please read these instructions carefully before beginning installation. If you need assistance, call Technical Support at (domestic calls), or (Option 2), or us at getinfo@telect.com. Inspect equipment after unpacking and compare it to the packing list. Immediately report any shipping damage, defects, or missing parts to Telect at Keep all documentation that comes with your shipment. Telect is not liable for shipping damage. If the product is damaged, notify the carrier and call Telect s Customer Service Department at (domestic only) or for further recourse. NOTE: For service or warranty information, please visit telect.com website, or inquiries to getinfo@telect.com and click on the Support tab, or phone us at (domestic only) or Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights nor the patent rights of others. This document and the products described herein are subject to change without notice. Page 1

2 1.2 Description Frame Devices on the frame provide points of attachment for the modules. Also see Figure 3, Asssembly Parts on page Keyways receive the two mating slide pins on the module assembly. Keyway 2. Threaded holes receive the two modulemounting screws. Threaded Hole 3. The latch bar accepts the module tray latch. Latch Bar NOTE: Latch bar adjustment screws shown in red circles. Figure 1 - Frame Page 2

3 1.2.2 Module Assembly The Module has three features used for attaching to the frame: 1. Two slide pins on the module assembly fit into the keyways on the frame. Slide Pin 2. The module is secured to the frame using the two modulemounting holes. Mounting Hole Module (left or right) Identifiers 3. The latch and guide on each tray hold it in the closed position. Latch & Guide Figure 2 - Module Assembly Page 3

4 Upper Trough Module Keyway Inside Latch Bar Adjustment Screws Outside Latch Bar Adjustment Screws Latch Bar Tray Latches Module Mounting Threaded Hole Frame Extenders Lower Trough Figure 3 - Asssembly Parts Page 4

5 1.3 Installation Installing the Module Assembly 1. For cabled modules, route the IF cable toward the back, between the latch bar and frame. Position the module on the ADF frame. 2. Align the module slide pins with the frame keyways and slide the module back until it stops. Insure both pins are fully engaged. 3. Close the module trays into the latch bar. The tray should latch easily. If not, go to Adjusting the Latch Bar, if required on page Secure one module onto the frame. 5. Align the holes on the module with the threaded holes and insert the screws provided. 6. Tighten the screws Installing the Next Module Assembly 1. Attach the dust cover on the top tray of the previously mounted module. 2. Repeat the steps in Installing the Module Assembly on page 5 for each additional module Adjusting the Latch Bar, if required Perform this procedure only with the first installed module per quadrant. All modules in the quadrant are affected. 1. Secure one module on the frame. Align the holes and insert the screws. Support the module so that it does not fall while you insert the screws. 2. Tighten the screws. 3. Loosen the six adjustment screws (three inside, three outside) holding the quadrant latch bar to the frame extenders. 4. Move the latch bar so that the module trays slide smoothly into the latch bar. 5. Retighten all six of the adjustment screws. The quadrant is now aligned. 6. Proceed to Installing the Next Module Assembly on page 5. Page 5

6 This page intentionally left blank. Page 6