ME110SSR ME110SSR-4AP ME110SSR-4APH ME110SSR-4A2P ME110SSR-C ME110SSR-CH ME110SSR-MB. MITSUBISHI Electronic Multi-Measuring Instrument

Transcription

1 MITSBISHI Eectronic MtiMeasring Instrment This mana is a simpe ersion. Pease contact or Serice Networ for a detaied ersion of ser s Mana. ME110SSR ME110SSRAP ME110SSRAPH ME110SSRAP Safety precation ME110SSRC ME110SSRCH ME110SSR (Aways read these instrctions before sing this eqipment) For personne and prodct safety pease read the contents of these operating instrctions carefy before sing. Pease sae this mana mae it accessibe when reqired and aways forward it the end ser. Indicates that incorrect handing may case hazardos conditions. Aways foow the instrctions becase they are important persona safety. Otherwise, it cod rest in eectric shoc, fire, erroneos operation, and damage of the instrment. Norma serice conditions se the instrment in an enironment that meets the Norma serice conditions as foowing points: Ambient temperatre :5 50 C, aerage day temperatre exceeds 35 C Hmidity :30~85%RH, condensing. Atitde: 1000m or ess Potion Degree : Atmosphere withot corrosie gas, dst, sat, oi mist. A pace withot excessie shocs or ibration. Do not expose rain and water drips. Do not expose direct snight. An area in where are no pieces of meta and an indctie sbstance disperse. Do not expose strong eectromagnetic fied and ambient noises. Instaation instrctions This instrment shod be instaed and sed by a qaified eectrician. The instrment mst not be powered and sed nti its definitie assemby on the cabinet s door. erity the foowing points; Axiiary power sppy and Measring ratings Axiiary power sppy Ratings otage Crrent Freqency 100 A015%(5060) 10A 100 DC05% 6W 77 AC phase netra / 80 AC phase phase 5A or 1A (ia crrent transformer) 50/60 Crrent circits,, C and are Measrement categoryⅠ. otage circits, P1, P and P3 are Measrement category Ⅲ. The instrment is be monted on pane. A connections eep inside the cabinet. Tighten the termina screws with the specified rqe and se the sitabe pressre connecrs andsitabe wire size. When wiring in the instrment, be sre that it is done correcty by checing the instrment s wiring diagrams. Be sre there are no foreign sbstances sch as sawdst or wiring debris inside the instrment. Do not drop this instrment from high pace. If yo drop it and the dispay is craced, do not ch the iqid crysta and or get it in yor moth. When ch the iqid crysta, wash it away at once. In order preent inasion of noise, do not bnch the contro wires or commnication cabes with the main circit or power wire, or insta them cose each other. eep the distance between commnicationa signa ines, inpt signa ines and power ines, high otage ines are shown beow, when rn parae each other. Before operating the instrment, yo shod first read thoroghy this operation mana for safe operation and optimized performance of the prodct. Deier this ser s mana the end ser. Srage conditions Ambient temperatre the : 60 C, aerage day temperatre exceeds 35 C Hmidity range 30~85%RH, condensing. Atmosphere withot corrosie gas, dst, sat, oi mist. A pace withot excessie shocs or ibration. Do not expose rain and water drips. Do not expose direct snight. An area in where are pieces of meta and an indctie sbstance disperse. Disposa When disposing of this prodct, treat it as indstria waste.. The battery is not sed for this prodct. Garantee The period of garantee is for 1 year from the sae date, except in the case that the faire has been cased by bad handing of the prodct, proided that it has been instaed according the manfactre s instrctions. EMC DIRECTIE INSTRCTION This section smmarizes the precations on conformance the EMC Directie of the cabinet constrcted sing this Instrment. Howeer, the method of conformance the EMC Directie and the jdgment on whether or not the cabinet conforms the EMC Directie has be determined finay by the manfactrer. 1. EMC Standards EN 61361:06 EN :06/A1:09/A:09 EN : Instaation (EMC directie) The instrment is be monted on pane of a cabinet. Therefore, the constrction of a cabinet is important not ony for safety bt aso for EMC. The instrment is examined by the foowing conditions. se a condctie cabinet. Six faces of a cabinet hae be ensred condctiity for each other. A cabinet has be connected earth by a thic wire of ow impedance. Hoes on faces of cabinet hae be 10 cm or ess in diameter. The terminas for protectie earth and fnctiona earth hae be connected earth by a thic wire of ow impedance. (A termina for protectie earth is important not ony for safety bt aso for EMC.) Protectie earth: Maintains the safety of the instrment and improes the noise resistance. Fnctiona earth: Improes the noise resistance. A connections shod be ept inside the cabinet. Wirings otside the cabinet hae be sed with the shieded cabe. The foowing diagram shows how proide good contact of the shieded cabe. Remoe part of the oter coer. Remoe part of the paint ms on the cabinet. Connect those parts with the camp. Screw Conditions Beow 600, or 600A power ines Other power ines ength 30cm or more 60cm or more Shied section Camp fitting Operation instrctions Paint mas Shieded cabe When the externa terminas are connected the externa eqipments, the instrment and the externa eqipments mst not be powered and sed nti its definitie assemby on the cabinet s door. The rating of the termina of the externa eqipment shod satisfy the rating of the externa termina of this instrment. (See Specifications.) Maintenance instrctions Do not ch the terminas whie a the circits connected this instrment are aie. Do not disassembe or modify the instrment. Do not contact a chemica dst coth contact the instrment for a ong time, or do not wipe it with benzene, thinner, acoho. Wipe dirt on srface with a soft dry coth. Chec the foowing points, Condition of the apepearance Condition of the Dispay nsa sond, a sme, and generation of heat Condition of the wiring and the attachment Chec on yor deiery Chec the foowing point as soon as yo receie Mitsbishi Eectronic MtiMeasreing Instrment : The pacage is in good condition. The prodct has not been damaged dring transit. The prodct corresponds yor order specifications. This prodct had the foowing accessories. Parts name Qantity Specifications ser s Mana 1 A3 size (this docment) Attaching nts M5 beeie spring nts (contained in a bag)

2 Monting 1. Dimensions of the pane The pane hoe dimensions are as shown beow. And it can be attached a pane of thicness 1.6.5mm. 90 ±1 ± φ10 ± 90 ±1. iew ange The contrast of the dispay changes at iew anges. iew ange φ6 (iewed from the side) (iewed from the p) Pane hoe dimensions (iewed from the front of pane) 3. Attachment When insert the main body in the pane hoe, insert it sowy nti the spper at the botm of the main body goes in the pane. After insertion, the effect of the spper preents the main body from dropping off een when yo reease yor hand from it. Fasten the attachment nt (M5 nt with beeie spring) with rqe abot Nm Wiring Wirings of the terminas hae be fastened according the foowing tabe. Externa diameter Screw specification Termina Fastening rqe Do not fasten three wires or more one termina. Otherwise, it may generate heat or ignition. Measrements inpts axiiary power inpt termina M screw For M screw of externa diameter beow ~ 1.7N.m Termina screw Otpt termina M3 screw M screw For M3 screw of externa diameter beow ~ 0.6N.m Protectie erasing termina For M screw of externa diameter beow ~ 1.7N.m Wiring Diagram Three phase wire type : Exampe of ME110SSRAP (with T) Three phase wire type : Exampe of ME110SSRAP (for direct inpt) Anaog otpt Anaog otpt CH Anaog otpt Anaog otpt CH Pse otpt CH CH CB CH CH CA Po(P) P() C C () () 1 OAD Anaog otpt Anaog otpt CH Anaog otpt Anaog otpt CH Pse otpt Pse otpt CH CH B CB CH CH A CA Po(P) P() C C () () 1 OAD Three phase 3wire(3CT) type : Exampe of ME110SSRAPH (with T) 1 3 Three phase 3wire(CT) type : Exampe of ME110SSRC (with T) 1 3 Anaog otpt Anaog otpt CH Anaog otpt Anaog otpt CH Pse otpt Aarm otpt CH CH CB CH CH CA A COM Po(P) P() C C CCin commnication DA DB DG SD Po(P) P() C C () 1 () OAD () () 1 OAD Singe phase 3wire type : Exampe of ME110SSRCH Digita inpt Aarm otpt DC CCin commnication A COM D1 D D1 Po(P) D D3 D3 DA DB DG SD P() C C 1 0 Singe phase wire type : Exampe of ME110SSR (with T) RS85 (ModBs) T/R T/R Ter SD Po(P) P() C C 1 () () 1 OAD () () 1 OAD 1Axiiary power sppy 100 AC 100 DC Fses gg type(iec69) or M type rated between 0.5 and 5A 1 For ow otage circits, gronding of the secondary side of T and CT is not necessary. Do not connect termina. "( )" shows termina boc No. for 3P3W,1P3W,1PW

3 > Dispay 3 and btn fnctions Fnctions of operation btns Dispay The operation btn hae arios fnctions according how they are pressed down. 1 1 EAD AG RE X/MIN PHASE DISPAY Set btn Reset btn Phase change btn / btn Maximm/minimm Dispay change btn btn Meaning of code : (press), (press oer 1 second), (press oer seconds), (press simtaneosy) Operation Btn Name Mode RE Max/ Fnction PHASE DISPAY Min Dispay changes. Phase changes. Mode changes the max./min. dispay and the instantaneos dispay The item expressed with the bar graph is changed. Harmonics nmber changes when harmonics dispayed. dispays change cycicay. phases change cycicay. The conting aes of three digits of ow ran are dispayed. After pressing once again, the dispay retrns. Maximm aes and minimm aes on the Ony aaiabe for dispay are reset the present ae. maximm/minimm A of the Maximm aes and minimm aes are reset the present ae. ae screen A of the conting aes are zero reset. the operation time is zero eset (Screen operation time ony) An aarm condition is canceed. (Screen eement is canceed) Aaiabe ony when mana canceation A aarm conditions are canceed. is set (Eement is canceed for a screens) Operation mode Setting mode/ Set ae confirmation mode BASIC Specia Mode Setting Operation Switch Specia Operation The atching data of digita inpt on the dispay is canceed. (Aaiabe ony for contact point inpt screen) The dispay of Set ae confirmation mode appears. The dispay of Setp mode appears. The setp items are saed, and setp item is changed next item. Bac the preios item. The aes of setp is changed. (If it presses for 1 sec or more fast forward or fast retrn.) Bac the Setp dispay. Retrns from infrared mode operation mode (Aaiabe ony for infrared mode) Bac the Setp dispay. Retrns set contents the defat settings (Ony effectie in CAE dispay) Whie the bac ight is off, if the operation ey is pressed, the bac ight is aways it. If the operation btn is pressed once again, the fnction in the aboe tabe appears. Note: When a of the conting aes are zero reset the CO emission ae is aso ceared. Setting fow If the fnction of maximm ae and minimm ae reset and Wh, arh zero reset are done, data wi be ost. If this data is needed,pease record the data before the reset operation. If the fnction of meter restart is done, the entire measrement (measrement dispay, aarm, anaog otpt, pse) sps. No. Segment Name Description 1 EAD stats Show direction power facr or reactie power on bar graph. 3 AG stats Scae of the bar graph Trns on at the additiona dispay of reactie energy. Show the scaes at the bar graph. nder scae inpt Trns on when measring aes fa beow the minimm scae. 5 Oer scae inpt Trns on when measring aes exceed the maximm scae. 6 7 Aarm indicar Index indicar When pper/ower imit aarm set, ficers at the imit setting ae. When set, trns on at the index indicar setting ae. Shows the item dispayed on the bar graph. 8 Bar graph stats When the item is the same as a digita dispayed item,indicated with, otherwise indicated with Digita stats Digita dispay nits Phase stats, 13N, X/MIN,demand etc. dispayed. Measred aes dispayed in digita. nits of measring ae dispayed. Indicates the mtipying facr for cacating energy Mtipying facr Metering stats Harmonics Setp mode stats Test mode stats pper/ower imit aarm stats Stats dispay for prodcts with transmission fnction 9 10 AARM Note: The aboe dispay is an exampe for expanation. Ficers when conting actie energy.(note.1) Trns on when harmonics dispayed. Trns on at setting mode. Ficers at setting ae confirmation mode. Trns on at the test mode. Ficers when pper/ower imit aarm is generated. Trns on when the instrment eqipped with commnication fnction. Ficers at commnication error condition. Note 1. The bining cyce is constant regardess of the size of the measred inpt Operation Mode Setting Mode or Setting ae Confirmation Mode Setting Men End Setting Men 1 (Basic Set p) Setting Men Setting Men 3 Setting Men Setting Men 5 Setting Men 6 Setting Men 7 Setting Men 8 Setting ae Confirmation Men 9 1 END Dispay Phase wire system Mode Option code Crrent maximm scae Indicar item Aarm item Anaog otpt 1 Enabe/disabe operation time dispay Test Mode 5 Sae the setting. Dispay Pattern Bacight brightness Actie power maximm scae Indicar ae Aarm ae Anaog otpt Enabe/disabe CO dispay Cance Dispay T/direct otage Bacight a off Actie power nit W/W/MW Aarm deay time Anaog otpt 3 Switch eement information Cance the settings. Primary crrent Time constant for actie power demand Dispay pdate time Men 1 for Setting ae Confirmation Mode > Reactie power maximm scae Reactie power nit Aarm cance method Bac ight ficers dring aarms Anaog otpt Anaog otpt imit CCin station nmber CCin bad rates ModBs address ModBs bad rates Amatic migration. Facry defat setting Time constant for crrent demand Mode dispay Option dispay Expanded conting Mor starting crrent deay time Pse otpt Power data resotion CCin ersion ModBs parity ModBs sp bit Phase wire system Dispay pattern Harmonics CCin mode reset ModBs mode reset Exampe of Setting Mode Exampe of Setting ae Confirmation Mode T secondary otage T primary otage CT secondary crrent CT primary crrent Digita inpt setting Digita inpt cance methad ON Bining Time constant for actie power demand Time constant for crrent demand 1: For Setting ae Confirmation, it retrns Operation Mode. : Repeat settings for p eements. : Setting is ony possibe for ME110SSRAP,APH and AP. : Setting is ony possibe for ME110SSRCH. 5: This is not dispay in Setting Mode. ME110SSRC ME110SSRCH <ME110SSR> Arrow in Figre Action ey operation Press them simtaneosy Shift from the operation mode the setp mode. RE for seconds. Shift from the operation mode the set ae Press it for seconds. confirmation mode. Seect the men nmber set or End. or Press it seera times. Get in each setting screen. Shift the next setting item. Go bac the preios setting item. DISPAY Omitted in figre Seect a set ae. or Press it seera times. Shift the End screen. This mana is a simpe ersion. Pease contact or Serice Networ for a detaied ersion of ser s Mana. Memorize the setting contents, and go bac the operation mode. Seect "CAE." Cance the settings. Sip remaining setting items dring setting. or Press it for 1 second Set aes retrn the facry defat ae. RE PHASE Press it for seconds

4 Operation Basic Operations whie Execting Settings Fnction Operation Remars Seect a set ae Press or Fastforward when pressed oer 1 sec. Setp items are saed Press Setp item wi be cared and shift the next item. Go bac the preios setting item Press DISPAY The set ae for the setting item jst before retrning is Sip remoing setting items dring Press and hod for 1 sec. sti aaiabe. setting Setting Men 1: Setting the Phase Wire System, Dispay Pattern, T/Direct otage, CT Primary Crrent, and Time constant for Demand In this setting men 1, There are setting the basic contents as foowing for correct measrement. In the operation mode, after pressing the and the RE simtaneosy for seconds or more, the foowing operation becomes aaiabe. Setting Men 1 Phase Wire system Set the setting men nmber 1. Set the phase wire system. 3P CT 3P3 : Threephase wire : Threephase 3wire (CT) Sppementa Information: nderined portions indicate the defat aes. (Same from here.) 3CT 3P3 : Threephase 3wire (3CT) 1N 1P3 : Singephase 3wire (1N) 1N3 1P3 : Singephase 3wire (1N3) 1P : Singephase wire Set the "Specia Primary otage" (Defat ae: 10,000) From p digit, seect the ae of the ficering digit by and. The setting digit can be moed right by. The setting digit can be moed eft by DISPAY. Setting is aaiabe in range from ess than 100 : pper digits setting Oer 100 : pper 3 digits setting * Error dispay (E05) appears when set ot of range. After that, pease press, reiew the setting ae and set it once again. Press at the owest digit, the setting step wi shift the next one. To CT Primary Crrent Dispay Pattern Set the dispay pattern. The foowing tabe shows the measrement eements that can be dispayed by each dispay pattern. (For more detais abot dispay patterns, refer detaied edition.)in addition, if there is no dispay pattern that yo want from P01 P13 (P1 and P15), seect the specia dispay pattern P00 configre the screen freey.(for more information abot setting the specia dispay pattern P00.) : Dispayabe at this dispay setting. : Set at other additiona settings. : Seect "P00" and set the dispay order and dispay position. (a) For threephase wire Dispay Pattern P01 P0 P03 P0 P05 P06 P07 P08 P09 P10 P11 P1 P13 P00 (b) For other phase wire system except threephase wire Additiona Screen (Sppementa) Dispay Pattern Crrent Crrent N phase crrent demand crrent demand crrent N Phase demand Crrent N Phase demand Crrent otage ine otage Actie Power Phase otage Actie demand Power Power facr Actie Power Reactie power Actie demand Power Freqency Power facr Actie Energy Reactie power Reactie Energy Freqency Actie Energy Reactie Energy Harmonic crrent Reactie Energy (Specia) Actie Energy (Exported) Apparent power Harmonic otage Additiona Screen (Sppementa) Harmonic crrent Reactie Energy (Specia) Actie Energy (Exported) Operation time Digita inpt (DI1 DI3) CO Emission N Phase Harmonic Crrent Harmonic otage Operation time Digita inpt (DI1 DI3) CO Emission Primary Crrent () For direct inpt (withot T) Set the direct otage. (a) For threephase wire (phase netra otage / phase phase otage) 63.5/ / /190 /380 /15 5/0 77/80 (b) When setting for threephase 3wire (CT, 3CT) or singephase wire 110 (a) For Threephase wire Set the primary crrent (Defat Setting: 5A) (b) For other phase wire system except Threephase wire Set the primary crrent of the CT. 1A 5A 6A 7.5A 8A 10A 1A 15A A 5A 30A 0A 50A 60A 75A 80A 100A 1A 150A 0A 50A 300A 00A 500A 600A 750A 800A 1000A 1A 10A 1.A 1500A 1.5A 1600A 1.6A 00A A 500A.5A 3000A 3A 000A A 5000A 5A 6000A 6A 7500A 7.5A 8000A 8A 10A 1A A 5A 30A SP. Note 1 3 T / Direct otage P01 P0 P03 P0 P05 P06 P07 P08 P09 P10 P11 P1 P13 P1 P15 P00 Note: The foowing settings are reqired for dispaying eements on an additiona screen. Measrement eement on additiona screen Setting item Actie Energy(Exported) / Reactie(Specia) Setting Men 3 Expanded conting Harmonic crrent / Harmonic otage Setting Men 3 Harmonics Dispay Digita inpt (DI1 DI3) Setting Men 7 Digita inpt setting Operation time Setting Men 8 Operation time dispay CO emission Setting Men 8 CO emission dispay When sing T Seect yes, and then press, shift foowing (1) When direct inpt (withot T) Seect no, and then press, shift foowing (). yes no <When 1 phase wire system is set singephase 3wire> se ony for direct inpt. This setp wi be sipped and the setting starts from Primary Crrent. The rating otage between P1P or PP3 is 110. It is between P1P3 Note 1: If there is no primary crrent in the aboe that yo want set, seect "SP." for specia primary crrent setting. Setting except SP : To 5Time constant for actie power demand When setting SP : To foowing Specia Primary Crrent Set the "Specia Primary Crrent" (Defat ae: 5A) From p digit, seect the ae of the ficering digit by and. The setting digit can be moed right by the. The setting digit can be moed eft by the DISPAY. Setting is aaiabe in range from 1.0A A ess than 10A : pper digits setting Oer 10A : pper 3 digits setting * Error dispay (E05) appears when set ot of A range. After that, pease press, reiew the setting ae and set it once again. Press at the owest digit, the setting step wi shift the next one To 5 Time constant for Actie power demand 10 Set p the time constant for actie power demand. (1) When sing T Set the secondary and primary otage of T. (a) For Threephase wire <Secondary otage (Phase phase otage) Setting Range> 5 Time constant for Actie power demand 0 second 10 seconds seconds 30 seconds 0 seconds 50 seconds 1 minte mintes 3 mintes mintes 5 mintes 6 mintes 7 mintes 15 mintes 8 mintes mintes 9 mintes 5 mintes 10 mintes 30 mintes <Primary otage (Phase phase otage) Setting> (The facry defot ae is 0) (b) When setting for Threephase 3wire (CT, 3CT) or Singephase wire <Secondary otage Setting Range> Note) Een when the dispay pattern not dispay the actie power demand, this screen appears. If the actie power demand is not necessary, press the as it is. 11 Set the time constant for crrent demmand second 0 seconds 3 mintes 7 mintes 15 mintes <Primary otage Setp Range> SP. 6 Time constant for crrent demand Setp Men 10 seconds 50 seconds mintes 8 mintes mintes seconds 1 minte 5 mintes 9 mintes 5 mintes 30 seconds mintes 6 mintes 10 mintes 30 mintes Note) Een when the dispay pattern not dispay the crrent demand, this screen appears. If the crrent demand is not necessary, press the as it is. According the setp diagram,sae the changed contents, or contine the other setp men. Note: If there is no primary otage in the aboe that yo want set, seect "SP." for a specia primary otage setting. Setting except "SP.": To CT Primary Crrent When setting "SP.": To foowing "Specia Primary otage" Note. If the contents in the setp men 1 are changed, the maximm ae, minimm ae, demand ae of reated measrement items wi be reset. (Howeer, actie energy and reactie energy wi not be reset.)

5 Setting Men 6: Setting the Anaog Otpt and Pse Otpt Otpt item of anaog otpt, pse otpt, pse nit and so forth are set here. In the operation mode, press and RE simtaneosy for seconds or more, and the foowing operation becomes aaiabe. Setting men Set the setting men nmber 6. (Set as shown in the right dispay.) Set the measrement item be otpt anaog otpt. Seect a measrement item for otpt from the foowing tabe. AR AS AT AN AAG () Demand AR Demand AS Demand AT Demand AN Demand AAG RN SN TN AS AG (N)(CH) AT RS A ST 3phase wire WR WS WT W () R S T arr ars art ar AR cosφr cosφs cosφt cosφ (CH) Harmonic AR Harmonic AS Harmonic AT Harmonic AN Harmonic RN Harmonic SN Harmonic TN Anaog otpt CH CH measrement item Anaog otpt CH CH detaied settings (3) When power facr is set as an otpt item Set the power facr ae for the maximm anaog otpt aes () When the freqency is set as an otpt item Set the freqency range for anaog otpt () () <When 50 is set> <When 60 is set> Set the measrement item that is otpt anaog otpt CH CH. The setting method is the same as Anaog otpt measrement item. Anaog otpt CHCH detaied setp The setting method is the same as Anaog otpt detaied setting. Anaog otpt measrement item TR AG () AG: Aerage : Tota effectie ae 3phase 3wire (CT, 3CT) AR () AS AT Demand AR Demand AS Demand AT RS (CH) ST TR W () ar cosφ (CH) Harmonic AR Harmonic AS(3CT) Harmonic AT Harmonic RS Harmonic ST 1phase 3wire 1phase 3wire 1phase wire (RNS dispay) (RNT dispay) AR () AN AS Demand AR Demand AN Demand AS RN (CH) NS RS W () ar cosφ (CH) Harmonic AR Harmonic AS Harmonic RN Harmonic NS AR () AN AT Demand AR Demand AN Demand AT RN(CH) NT TR W () ar cosφ (CH) Harmonic AR Harmonic AT Harmonic RN Harmonic NT A () Demand A (CH) W () ar cosφ (CH) Harmonic A Harmonic Note 1:The same measrement items can be set for each anaog otpt. Note :It is possibe seect measrement items that are not incded in the set dispay pattern. Note 3:Setting "" are minimm otpt. In addition, it moes the next anaog otpt setting. Note :For the harmonic crrent, the ta RMS ae is otpt by a scae from 0 60% of the rating. For the harmonic otage, the ta disrtion ratic is otpt by scaing 0 %. Note 5:nderined portions are the facry defat settings for measrement eements assigned each anaog otpt. Anaog otpt detaied setp (The foowing setting can be made separatey from the measrement items incded in the dispay pattern.) (1) When the crrent / crrent demand / actie power / actie power demand / reactie power are set as otpt items. (a) Set the measrement ae for the maximm anaog otpt ae. Otpt eement Setting range *3 3 STEP (Abot 1%) A ±0 STEP (100%: Rating) Demand A 10 STEP (Abot 0%) Anaog otpt imit Pse otpt 1 otpt item Pse otpt 1 pse nit Set anaog otpt for when f scae is oer the imit. Setting ae off (No imit) on (imited) Description For the span ae, the maximm otpt is 5% and the minimm otpt is 5%. For the span ae, the maximm otpt is 1% and the minimm otpt is 1%. Note: When the otpt item for a anaog otpt is set "," this setting is sipped. Set the item that is otpt pse otpt 1. Setting ae Actie energy (Imported) Actie energy (Exported) Reactie energy (Imported, ag) Reactie energy (Imported, ead) Reactie energy (Exported, ag) Reactie energy (Exported, ead) Dispay Section (A) Section (B) Section (C) OFF OFF (No otpt) OFF OFF Set the pse ae of pse otpt 1. Pse ae is seected from the tabe beow, according ta oad [W]. Section (C) Section (A) Section (B) Note: The segment shown in the eft tabe bins according the seected eement. α: 1 1phase wire α (T Primary otage) (CT Primary Crrent) Tota oad [W]= 1phase 3wire phase 3wire 3 3phase wire *1: For 1phase 3wire setting, the T primary otage is cacated sing 110. *: For direct otage setting, the direct otage is sed for cacation instead of the T primary otage. *3: For 3phase wire setting, the T primary otage is cacated sing the phase netra otage. Tota oad Dispay format Possibe pse nit settings [W] Digita dispay Mtipier [Wh/pse] ess than or higher bt ess than or higher bt ess than or higher bt ess than or higher bt ess than or higher W ar 3 STEP (Abot 1%) ±0 STEP (100%: Rating) 18 STEP (Abot %) *1 Note 1: When Pse otpt 1 otpt eement is set "," this setting wi be sipped. Note : The facry defat setting aes are minimm aes for the pse nit that can be set. Note 3: For reactie power, W in the aboe tabe needs be read as ar, and Wh needs be read as arh. Anaog otpt detaied setting (b) Set the Singedefection / dabe defection / specia defection for anaog otpt. Otpt eement W Singe Setting range Dabe Specia defection defection defection ar Singe defection Dabe defection <Singe defection> <Dabe defection> <Specia defection> 1 0 (c) For specia defection, set the measrement ae for the minimm anaog otpt ae. Otpt eement W 0W 0W 0 0W Setting range *3 7.5W 0 0W 1 STEP (Abot 15%) 15 STEP (Abot 5%) ±0 STEP (Abot 100%) * Pse otpt otpt item Pse otpt pse nit DISPAY Set the item that is otpt pse otpt. (ME110SSRAP) The same item as pse otpt 1 can be set. The setting method is the same as Pse otpt 1 otpt eement. (Facry defat setting ae: Reactie energy (Imported, ag) Set a pse nit for pse otpt. (ME110SSRAP) The setting method is the same as for Pse otpt 1 pse nit. (Facry defat setting aes: Minimm possibe ae for pse nit) Set the pse width for otpt pse. Set according the inpt pse conditions for the receier. Pse width 0.15s 0.500s 1.000s Note When the pse nit is set the minimm ae and the pse width is set 0.500s or 1.000s, the pse otpt cannot foow if the oad is o arge, which can rest in a decrease in the pse otpt nmber. *1. When A or Demand A are set as otpt eements, it moes the next anaog otpt settings. *. When other than specia defection is seected, it moes the next anaog otpt settings. *3. Abot Detaied setting aes refer a detaied edition. To next CH settings Setting men According the setp diagram, sae the changed contents, or contine the other setting men. () When otage is set as an otpt eement for 1phase 3wire Set RN and NS (NT) for the maximm anaog otpt ae <When 150 is set> <When 300 is set> Note: RS (RT) is fixed at

6

7 RE X/MIN PHASE DISPAY Externa Dimensions Warranty If yo hae any qestion or technica trobes in sing the prodct, contact Mitsbishi Eectric System & Serice or yor nearest branch of Mitsbishi Eectric Corporation. (Refer the end of this instrction mana for detais.) MITSBISHI 110 ME110SS The prodct is nder free warranty for one year from prchase or 18 months after prodction, whicheer comes first. The chargefree warranty sha appy ony if the prodct is being sed propery in the conditions, with the methods and nder the enironments in accordance with the terms and precations described in the cataoge and instrction mana, etc. Repacement sha be charged for the foowing cases een dring the chargefree warranty period. 1Faires de improper srage, improper handing, careessness, or negigence 110 Ø99 Faires de improper instaation 3Faires de improper sage and nathorized modifications Spper Attachment screw M5 Faires de externa facrs sch as fire, and abnorma otage, and force majere sch as an earthqae, wind, or fooding. 5Faires de matters npredictabe based on the ee of science technoogy at the time of shipping. Or company sha not be iabe compensate for any oss arising from eents not attribtabe or company, opportnity oss and ost earnings of the csmer de faire of the prodct, and oss, secondary oss, accident compensation, damage other prodcts besides or prodcts and other operations cased by a specia reason regardess of or company s abiity foresee it Specifications Type Phase wire system Rating Measring Items and accracy Measring Method Dispay Response time Item Specification ME110SSR,ME110SSRAP,ME110SSRAPH,ME110SSRAP, ME110SSRC,ME110SSRCH,ME110SSR Three phase wire(3pw),three phase 3wire(3P3W),Singe phase3wire(1p3w), Singe phase wire(1pw) Crrent 5AAC, 1AAC (1AAC is speciaprpose item) 3PW: max77/80ac otage 3P3W,1PW: 110AC,AC 1P3W, AC (110/AC) Freqency PW 3P3W,1P3W 1PW Dispay Otpt Crrent (A) A1, A, A3, AN, Aag A1, A, A3 A1 Crrent Demand (DA) DA1, DA, DA3, DAN, DAag DA1, DA, DA3 DA1 otage () 1, 3, 31, ag(), 1, 3, N, N, 3N, ag(n) 0.5% 0.5% Actie Power (W) ΣW, W1, W, W3 ΣW ΣW Actie Demand Power (DW) Σ DW, DW1, DW, DW3 ΣDW ΣDW Reactie Power (ar) Σ ar, ar1, ar, ar3 Σar Σar Apparent Power (A) ΣA, A1, A, A3 Power Facr (cosφ) Σcosφ, cosφ1, cosφ, cosφ3 Σcosφ Σcosφ.0%.0% Freqency () 0.5% 0.5% Actie Energy (Wh) Import, Export.0%.0% Reactie Energy (arh) Import Capacitie, Import Indctie, Export Capacitie, Export Indctie.0%.0% HI1, HI, HI3, HIN HI1,HI3 HI1.5% Harmonics Crrent (HI) Harmonics otage (H) Instantaneos ae Demand ae Type Nmber of dispay digits Bar graph Dispay pdating time intera Anaog otpt (ME110SSRAP/APH/AP) Aarm otpt (ME110SSRAPH/CH) Pse otpt (ME110SSRAP/APH) Digita inpt (ME110SSRCH) Power Faire Compensation T A CT Consmption Axiiary power Digita inpt Axiiary power Weight Dimension Encosre Operating temperatre Operating hmidity Srage temperatre THD, h1...h13 (withot een nmber) RMS ae and Disrtion ratio (max.100%) (Tota RMS, 0 Rated x 60%) H1N, HN, H3N H1, H3 H1.5% THD, h1...h13 (withot een nmber) RMS ae and Disrtion ratio (max.%) (THD,0 %) A,: RMS cacation, W,ar,A,Wh,arh: Digita mtipication, cosφ:power ratio cacation : Zerocross, H,HI: FTT Therma type cacation CD with bacight A,DA,,W,DW,ar,A,cosφ: digits,hi,h: 3 digits Wh,arh: 6 digits 1 SegmentBar graph, SegmentIndicar 0.5s / 1s Dispay: s or ess, Anaog otpt: s or ess In HI and H, 10s or ess Range ~ DC oad resistance 600Ω max Nootage a contact 35DC, 0.A Nootage a contact 35DC, 0.1A Rated DC(19 30DC) Non oatie memory (Items: setting ae, max/min ae, actie/reactie energy) 0.1A/phase, 0.A/phase (at direct inpt) 0.1A/phase 8A at 110AC, 9A at AC, 6W at 100DC D930, nder AC (10%,15%) 50/60 100DC (10%,30%) 0.5g 110(H)x110(W)x98(D) Thermopastic sefextingish (90) 5~50 C (aerage operating temperatre ; 35 C or ess per day) 85%RHmax, condensing ~60 C Standard EMC:EN61361:06 D:EN610101/01 Note1: Accracy is specified according the maximm scaes ae of rated ae. Note: Measrement of harmonics which its disrtion ratio is exceeded 100% may exceed the accracy Note3: Harmonics cannot be measred withot otage inpt.

8 Specifications Commnication Specifications ME110SSRC,ME110SSRCH Item Specifications CCin station type Remote deice station (er. 1 remote deice station or er. remote deice station) Nmber of occpied stations er. 1 remote deice station (er. 1 compatibe sae station) setting:1 station er. remote deice station (er. compatibe sae station) setting:1 station (Expanded cycic setting: Octpe) CCin ersion CCin er 1.10 /.00 Transmission speed Can seect from 156 bps/ 65 bps/.5 Mbps/ 5 Mbps/ 10 Mbps Maximm nmber of If the system is configred by ony this instrment, p nits can be connected.(note 1) connected stations note1: As for detais, refer the foowing manas. Mana Name Mana Nmber (Mode Code) CCin System Master/oca Mode ser s Mana type QJ61BT11N SH08039E Describes the system configration, performance specifications, fnctions, handing, wiring and (13JR6) trobeshooting of the QJ61BT11N. (Optionay aaiabe) CCin Dedicated Cabe se the CCin dedicated cabes for the CCin system. If a cabe other than the CCin dedicated cabe is sed, the performance of the CCin system cannot be garanteed. For the specifications of the CCin dedicated cabes or any other inqiries, isit the foowing website: CCin Partner Association: RER For detais, refer the CCin cabe wiring mana issed by CCin Partner Association Abot Programming In addition this mana, read the foowing docments o. Eectronic mtimeasring Instrment programming mana (CCin)... AN00503 Eectronic mtimeasring Instrment programming mana (CCin) (For er. remote deice station)... AN ME110SSR Item Specifications Interface RS85, wires haf dpex Proco ModBs RT (binary data) Speed 0, 800, 9600, 190, 3800bps Distance 1000m address 155 Station nmber 31 Resistance at end of the in 1Ω 1/W Recommended cabes Shieded twisted pair, AWG6 (or wider) gage As for detais of ModBs commnication, refer Modbs. org.website Modbs. org.website : Handing precations Precationary note written in orean Distribrs and sers mst nderstand that this prodct meets the eectromagnetic compatibiity reqirements and is designed for indstria se(cass A).Do not se the prodct in a residentia area. note1: This is the notification for the C mar (orea Certification) MITSBISHI Eectronic MtiMeasring Instrment Contry/Region Company Address Teephone Astraia Mitsbishi Eectric Astraia Pty. td. 38 icria Road, Rydamere, N.S.W. 116, Astraia China Mitsbishi Eectric Amation (CHINA) td. 17/F., ChangXing Financia Center, No.88 West Nanjing Road, Shanghai, China Mitsbishi Eectric Amation (Hongong) td. 10/F., Manife Tower, 169 Eectric Road, North Point, Hong ong Erope Mitsbishi Eectric Erope B.. Gothaer Strasse 8, D0880 Ratingen, Germany 9(0)10860 Indonesia P. T. Sahabat Indonesia P.O.Box 505 awasan Indstri Pergdangan, Jaarta, Indonesia 6(0) orea Mitsbishi Eectric Amation orea Co., td 1806, GayangDong, GangseoG, Seo, orea eba Compir d'eectricite Generaeiban Cebaco Center Boc A Astrade Dora, P.O. Box Beirt eba Phiippines Edison Eectric Integrated, Inc. th F. Gaeria Corporate Center, Edsa Cr. Ortigas Ae., Qezon City Metro Mania, Phiippines 63(0) Singapore Mitsbishi Eectric Asia Pte. td. 307, Aexandra Road, #0501/0 Mitsbishi Eectric Biding, Singapore Soth Africa CBIeectric: ow otage Priate Bag 16, Isando, 1600, Soth Africa 7(0) Taiwan 6th F., No.105, W ng 3rd, W Hsiang, Setsyo Enterprise Co., td Taipei, Taiwan, R.O.C. 886(0) Thaiand nited Trading & Import Co., td. 77/1 Bamrngmang Road, ong Mahana, Pomprab Bango Thaiand 6633 ietnam CTY TNHHTM SA GIANG 10th Foor, Room , 55 Tran Hng Dao St., Co Giang Ward, Dist 1, Ho Chi Minh City, ietnam /8/9 M06Z808H01 IB63661