6MSD Weekly Scheduling Meeting. 1:30, MCC Conference Room

Transcription

1 6MSD Weekly Scheduling Meeting 1:30, MCC Conference Room August 24, ) Glance Back and 2-Week Look Ahead (F. Pilat) mins 2) PMI Report (P. Collins)... 5 mins 3) Critical Path Service Provider Reports mins (a) Alignment (Curtis) (b) Installation/Alignment (Wilson) (c) HPRF (Kimber) (d) EESIC (Garza) 4) Hall Status Reports (D. Tilles) mins 5) Special Topics: None... 0 mins 6) Safety Report: None... 0 mins 7) Meeting Recap and Action Items (All)... 5 mins

2 6MSD: Glance back & look ahead Fulvia Pilat 6MSD Meeting August 24, 2011

3 Progress Wed Aug 17 Wed Aug 24 Weeks: 15 down, 12 to go Highlights: SLinac now in power permit for CM commissioning C100 successful gradient measurements! Arc10 dipoles installation completed Areas of attention: C100 1 (problem with pressure readbacks no Q measurements yet ) C100 2 cool down maybe today (delay) FEL setback on gun work try again. Impact on start of FEL run. Civil construction schedule (meeting today 2:30pm) Hall A/G2P schedule Hurricane preparation (already started, status meeting tomorrow)

4 CCB Report NO CRs & NTFs have been submitted, reviewed, and approved this week CR/NTF in the pipeline Hall C Moeller Quad (CR) The Moeller quad that is used for the Qweak program has a problem and must be removed for repair or to make room to move the other installed quad into position. N. Wilson is developing the schedule. More details to come in one week. CR/NTF Placeholders Tunnel Penetrations Repair (CR) Captures additional detailed scope for the repair work on defined penetrations. A&E final design drawings for the repair work reviewed by FML 2. CR will be updated and resubmitted for repair (prototype) for existing penetrations (to be defined based on accelerator lock up schedules). System Testing/Hot Checkout/Restart Operations Plan (CR/NTF) M. Spata is leading the preparation and planning for overall testing, hot checkout and restoration of operations for the 6 GeV run. The plan will be presented and reviewed August 31 st. Hall C Ion Chamber/Dump Work (CR) Hall C ion chamber and dump work being reviewed by engineering division and accelerator operations for scope. Draft plan led by A. Freyberger has been submitted. The area is still too "hot" for entry per RadCon Modification of C100 1 and C100 2 installation and testing schedule. Meeting held August 18, new schedule based on the shortening of installation time for C100 2: based on experience for C100 1 plus better inter group coordination

5 4 weeks look ahead C100 2 acceptance tests in TestLab + installation C100 1 tests in SLinac SAB LCW complete PSS certifications injector injector in beam permit Start of FEL IR run BSY Penetration construction continues ESR Cool down ready for end station support, HDice cool down RF installation & testing continues Peppo installation, tight still possible. Hall A G2P, septum and target installation Hall B: Installation, cool down of HD ice target

6 4 week look ahead heated topics C100 1 and C100 2 schedule Held meeting last week to address impact on Start up plan Civil work schedule Rebecca will hold meeting today to address impact on Start up plan Integrated plan for testing/hot check out/back to ops Meeting/REview August 31, led by Spata Possible impact of earthquake on alignment If, so alignment group resources Possible impact of Irene on overall shutdown Lab on Hurricane emergency 2 tomorrow, work already started

7 PM&IP 6MSD 8/24/11 Weekly Progress Meeting (8/19/11 Data) Report #15

8 PM&IP Schedule Issues: Hall D Phase 3 Tunnel Extension is ~18 Days behind schedule. C100-2 Installation Date 16 Sept 2011 Hall A Septum Platform Parts Issues Resource issues: Survey & Alignment 12 Sept 23Sept

9 PM&IP Other Schedule Information at Four Week Look Ahead - Shows all activities that have started that are not complete and any activities due to start in the next four weeks Critical Path Shows all MUST activities that have 2 days or less float. Schedule Variance - Shows all MUST activities that are not 100% complete and that the Start/Finish dates have slipped by at least 5 days.

10 Shutdown Work Summary Organization: Alignment Name: Chris Curtis Date: 24th Aug, 2011 Last Week Work That Went Better Than / As Expected: Step 2A (initial alignment) of east arc completed. Q Weak hydrogen cell fiducialized. Hall D control re survey ongoing. HD Ice target initial alignment ongoing. Work That Went Slower Than Expected, Delays, and Issues: Magnitude 5.8 earthquake unplanned. Checks being carried out. Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12 Gev Arcs X TBD Alignment of re installed dipoles in west and east arcs. Step 2B in west arc to start next week. Checks start tomorrow. Arc 10 Magnets X Opportunistic Quad / dipole Step 2A alignment. Continuing as appropriate. Hall A G2P X TBD Harp fiducialization & motion check. Waiting for harp. Due end of this week. Hall D X Before solenoid Re measure survey control in the Required for installation. Stability installation hall. checks being carried out. 6MSD weekly mtg Align Aug 24 Page 1 of 2

11 Table 2: Other Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12 GeV Arcs X TBD Dipole re alignment. Continuing on north part of west and east arcs for the next 2+ weeks. PEPPo X October Layout and alignment of PEPPo components Ongoing. Decision made on the best time for final alignment in NE section. Dates seem to have slipped, some deliveries late September. Q Weak X???? Target alignment Started fiducialization. HD Ice X Early September Align target Initial alignment started early. FEL X Early September Wiggler alignment 12 GeV Linacs X Mid? September SL25 cryomodule Hall D X Mid September Solenoid alignment Scope has increased. Has the potential to increase further. New Work Requests Requiring Schedule Changes: Hall D solenoid fiducialization. Permits Not Already in Hand (hot work, lifting, blind penetrations): None Significant Problems Pending (delays, technical issues, resource issues, scheduling): None Staffing Outlook: Currently running 2 crews of 3. Possible issues if work scope increases, or bunches up. 6MSD weekly mtg Align Aug 24 Page 2 of 2

12 Shutdown Work Summary Organization: MSINST Name: Neil Wilson Date: 8/24/11 Last Week Work That Went Better Than Expected/Completed: Girder & Dipole Installation Arc 10 Completed West Arc North Pump Down & Leak Check Completed. 45 MeV Dump Set in place Work That Went Slower Than Expected, Delays, and Issues: Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12GeV X Dipole Hook Up LCW & Vac. East & West Arc North, Includes Tightness Checks. Waiting on hose Ftgs. 12GeV X Fabricating Headers for Klystron Working 12GeV X 45 MeV Dump Shielding Dump Set. Hall C X Q Weak Quad Repair/Swap Working Mech & Vac 12GeV X NLINAC CPS Installation Delivery Date? Hall A G2P X Installation Support On Call, assembling girder. 6GeV X Swapping Out Vacuum Valves On Going Maint Weekly Report Page 1 of 2

13 Table 2: Other Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12GeV X Fabricating Headers for Klystron Manifolds on Site Racks & CPS s 12GeV X SL 24 & 25 Warm Region Girder After C100 2 Hall D X LCW Piping Installation On Hold PEPPo X Installation Support G2P X Continuing Installation Support 6GeV X Vacuum Valve Limit Switch Replacement & Vac. Support. New Work Requests Requiring Schedule Changes: None Permits Not Already in Hand (hot work, lifting, blind penetrations): None Significant Problems Pending (delays, technical issues, resource issues, scheduling): None. 8 weeks to tunnel lock up, hot check out & beam ops start!! Staffing Outlook: None Weekly Report Page 2 of 2

14 Shutdown Work Summary Organization: HPRF Name: Andrew Kimber Date: 24 August 2011 Last Week Work That Went Better Than/As Expected: Commissioning of 2L24 zone seems stable o We are having a consistent failure on a power supply board counterfeit diodes?!? Installation/testing of 2L25 o New firmware uploaded to CPS#2 o Checked out most signals, almost ready for RF Installation of 2L23 o General cable installation continues, LCW parts pressure tested, bad weld found manifold (replaced) o Cabling 90% complete (waiting for solenoid PSU s, interlocks, klystrons) o LLRF chassis in place Installation of 2L22 o Waveguide complete as far as we can o Waiting for card cages (2 of 4 nearing completion) Work That Went Slower Than Expected, Delays, and Issues: Zone infrastructure (IOC s, network, screens) can it be streamlined for future zones? Shutdown Work Summary AJK 24AUG11 Page 1 of 2

15 Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12GeV HPRF x ongoing Support CM commissioning 2L24 12GeV HPRF x 8/26/11 2L25 test into shorts Slightly later than plan, but with ~2 weeks of float 12GeV HPRF x Late Aug, (klystron dependent) 2L23 installation continues Shutdown Work Summary AJK 24AUG11 Page 2 of 2 LCW manifolds, klystrons (3 on site, 5 due by end of month) MechTech x 8/26/11 CPS#6 in 1L22 will be shipped Thursday 25th 12GeV HPRF x?? Hurricane prep/cleanup Some resource lost to prep work Table 2: Other Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12GeV HPRF x Mid Sep Tunnel Waveguide and cabling install 12GeV HPRF x Mid Sep 2L23 Test into shorts complete Klystron dependent 12GeV HPRF x Aug/Sep 2L22/2L26 installation New Work Requests Requiring Schedule Changes: n/a Permits Not Already in Hand (hot work, lifting, blind penetrations): n/a Significant Problems Pending (delays, technical issues, resource issues, scheduling): 2 FA HOM filters due the end of July, 2 FA units to be shipped Sep 16th Staffing Outlook: Good

16 Shutdown Work Summary Organization: EESIC Name: Omar Garza Date: Last Week Work That Went Better Than Expected: BIAHRD Project: Conversion of CAMAC to VME (West ARC PMs, Vacuum, Diagnostics, etc.) Work That Went Slower Than Expected, Delays, and Issues: DECA RAD Design, Testing G2P Harp Motor Drive System Design Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns Hall C Cavity Electronics G2P BPM Electronics 12Gev SRF Vacuum Instrumentation X PCB Design Chassis Fabrication, Brd. Assembly, Test 2 Ch. PCB ordered nxt wk. X PCB Design, PCB layout, Procure, Layout changes to 4 Ch. Receiver Chassis Assemble, Test Ongoing X SL24,25,23 Checkout/Testing EPICS Screen Shutdown Work Summary Page 1 of 2

17 Table 2: Other Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns SRF DECA RAD Instrumentation AIPBSY (I to V) Module G2P Harp Motor Driver Chassis Design X Prototype Testing, Cable Capacitance/Work Around Fabrication Ongoing Screens completed X PCB design Assembly, testing Software X Chassis, PCB Board New Work Requests Requiring Schedule Changes: Prototype testing, Final check firmware Permits Not Already in Hand (hot work, lifting, blind penetrations): Significant Problems Pending (delays, technical issues, resource issues, scheduling): Engineering resource for G2P Harps, 12Gev HPA Intlks, Decarad Staffing Outlook: Resource, Software Shutdown Work Summary Page 2 of 2

18 Work Summary Organization: Hall A Name: Folts Date: 8/23/11 Last Week Work That Went Better Than Expected: Work That Went Slower Than Expected, Delays, and Issues: Target stand parts Harp controls work Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns Septum magnet continuing G2P Target x continuing Modifying Septum platform Parts are an issue G2P Target x continuing Assembling for testing Delayed due to Q week priority G2P x continuing Power supply installation Final hookup G2P beam dump x On order Assembly, pre survey, install Delayed due to changes Hall maintenance x continuing General repair and maintenance Beam line x working Harp controls work I&C work load conflict (firmware) Hall B. No concerns, working on detectors and HDice is installed Hall C. No concerns, working on Moller, SOS decontamination and SHMS rails. Shutdown Work Summary for Walter Page 1 of 1

19 Shutdown Work Summary Organization: Hall B Name: Doug Tilles Date: 8/24/2011 Last Week Region 3&2 Sector 3 Drift Chamber 100% Remove R3S3 Steel work 100% Start installation of R3S2 Steel work 100% Region 2 Repairs done 100% 2C24 Viewer 90% Work That Went Slower Than Expected, Delays, and Issues: HDice 1 day late for installation FWD Carriage plate installation Ongoing Shutdown Work Table 1: Next Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 6 GeV repairs Setup and pull Region 3 Sector 3 Drift chamber Cosmic test of Drift Chamber X X Wed Morning Start Region 3 Sector 3 Repairs of Region 3 and 2 8/24 Page 1 of 4

20 Project & Customer Status Completion Tasks Comments/Concerns HDice Lab work HDice to Hall HDice on beam line Electron Run Blower Fab Blower suction line 12GeV Drift chamber Region 1 shipment. X X Done 8/18 Electron blower on going Pump on order Ongoing X ESB Building Ready for shipment 100% Table 2: Other Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns Region 3 S3 removal and repair Warm HDice Alignment Cool Down HDice x or 8 24 Sep 1 New Work Requests Requiring Schedule Changes: HDice Hall Alignment Aug 23 Permits Not Already in Hand (hot work, lifting, blind penetrations): None needed Hot work complete Significant Problems Pending (delays, technical issues, resource issues, scheduling): None 8/24 Page 2 of 4

21 Staffing Outlook: OK 8/24 Page 3 of 4

22 8/24 Page 4 of 4

23 Shutdown Work Summary Organization: Hall C Name: W. Kellner Date: Ongoing Shutdown Work Table 1: This Week's Work ( green = no concerns; yellow = some concerns; red = serious concerns) Project & Customer Status Completion Tasks Comments/Concerns 12Gev SHMS 50% Cleaning and painting the new SHMS rails for outside storage 6Gev SOS Starting Decontamination of the SOS (hopefully) electronic hut and detector hut (post lead removal cleanup) 6Gev Q weak Continuing Assisting Moller magnet repair, removing vacuum pumps etc. Table 2: Upcoming Work ( green = no concerns; yellow = some concerns; red = serious concerns) Unscheduled IH decontamination approval/plan completed Challenging Project & Customer Status Completion Tasks Comments/Concerns Other On hold Pressure and leak test new SHMS instrumentation manifolds 6Gev Q weak On hold Reinstall main detector when repaired Other Assisting LCW system differential pressure gauge replacement (man lift etc) Unscheduled, TOSP signed Waiting for users to complete repair Unscheduled Shutdown Work Hall C Summary August Page 1 of 1

24 Good Day! First Aid Injury *Click on symbol in calendar for details Recordable Injury *Click on symbol in calendar for details Project to Date: First Aid: 20 Recordable: 2 DART: 2 Other Noteworthy Events *Click on symbol in calendar for details

25 August 2011 Events 2 Date Location Event 08/01/11 Test Lab parking lot 08/02/11 South Linac zone 24. Employee was closing the van ramp and turned his head to the right. After getting in the van to leave he felt pain in the right side of his neck and was diagnosed with neck strain and there was no treatment needed at this time. Employee has returned to work with no restrictions. Two employees called to report that while measuring voltage, they felt a tingle in his right index finger. The sensation was immediately resolved. Employees reported minor electrical exposure and no medical assistance was needed at the time of notification. Employees returned to work on regular duty. 08/08/11 Building 87 Employee states "while carrying boxes into the building, the door began to close and my arm was scratched by the door latch." Employees was diagnosed with a superficial laceration to the right arm and the wound was cleansed and treated with an over the counter antibiotic ointment and dressing. Employee returned to regular duty.

26 Safety Observations Through 8/23/ Observations made of 6MD related work 73% were all safe Category Number of Observations Percent of Observations All Safe % Housekeeping 25 6% PPE 20 4% Ladders 15 3%

27 Irene