INSTRUCTION MANUAL FOR THE INSTALLATION, USE AND MAINTENANCE OF THE REGULATOR GENIUS POWER COMBI

Transcription

1 NSTRUCTON MANUAL FOR THE NSTALLATON, USE AND MANTENANCE OF THE REGULATOR GENUS POWER COMB (TRANSLATON OF THE ORGNAL NSTRUCTON MANUAL N TALAN) PRELMNARY VERSON

2 WARRANTY The devce s guaranteed 24 months from date of purchase aganst defects n workmanshp or ts materals. Falures due to nexperence or napproprate use of the regulator are excluded from warranty. No warranty at any tme f the devce has been tampered or opened by unauthorzed personnel Warranty does not cover the replacement of the devce Transport costs are borne by the owner of the devce Always reference the seral number and model of your devce when contactng the techncal assstance servce RANGE OF PRODUCTS CODE MODEL OUT P TOT GENUS POWER COMB 6 6A 1.4KVA GENUS POWER COMB 10 10A 2.3KVA GENUS POWER COMB 12 12A 2.8KVA DENTFCATON PLATE The GENUS POWER COMB regulators are recognzable by the dentfcaton plate placed both on the front of the devce and on ts packagng box. 1. MANUFACTURER DATA 8. PROTECTON LEVEL 2. AUTOTRANSFORMER SYMBOL 9. CURRENT OUTPUT 3. CE MARKNG 10. TOTAL POWER 4. SERAL NUMBER 11. SUPPLY VOLTAGE 5. SHORT-CRCUT VOLTAGE [%] 12. REGULATOR CODE 6. OUTPUT VOLTAGE 13. REGULATOR MODEL 7. ADMTTED FORM FACTOR Tamperng, removal, lack of the plate does not allow relable dentfcaton of the product and makes dffcult any nstallaton and mantenance workng.

3 BOX CONTENTS The GENUS POWER COMB regulators are delvered n a sngle package protected by a cardboard box. The box contans: 1 GENUS POWER COMB regulator 1 nstructon manual 1 plastc sachet contanng: o 1 5-pn connector wth quck-clampng screw o 1 Shell coverng the connector for wall mountng o 4 Termnal blocks for mountng on omega bar SYMBOLS Ths manual uses the followng symbols: h 6 WARNNG. Actons and procedures that requre specal cauton and adequate preparaton whch lack may cause malfuncton and/or rsks for the operator SHOCK HAZARD. Actons and procedures are to be carred out wth partcular attenton whch lack may consttute a rsk of electrc shock PROHBTED. Actons that SHOULD NOT BE MADE absolutely

4 NDEX - COVER - CONFORMTY - CERTFCATONS - RANGE OF PRODUCTS - DENTFCATON PLATE - BOX CONTENTS - NDEX - SYMBOLS - GENERAL WARNNGS - GENERAL SAFETY RULES - USAGE OF THE GENUS COMB - DESCRPTON OF THE REGULATOR - VEWS OF THE DEVCE o GLOBAL o FRONTAL - ELECTRCAL CHARACTERSTCS - SZE AND WEGHT - NSTALLATON: o FXNG o CABLE CONNECTON o CONNECTOR WTHOUT HOUSNG o CONNECTOR WTH HOUSNG o TERMNALS SECTON o CONNECTON o 1PH/3PH WRNG DAGRAMS - START AND USE o OPERATNG PRNCPLES o FRST START o WARMUP CYCLE SET-UP o SET VOLTAGE LEVEL o BYPASS o ALERTS o EXTERNAL BY-PASS - TROUBLESHOOTNG o TROUBLESHOOTNG TABLE

5 GENERAL WARNNGS Carefully read the nstructons n ths manual. After unpackng, check the ntegrty and completeness of delvery and n case of non-complance, contact Agentech srl. Devce s ntended for professonal use only GENUS POWER COMB regulators are not ntended for household or resdental use nstallaton and mantenance of the GENUS COMB must be performed by a qualfed electrcan or competent staff Agentech Srl shall not be lable for damage to persons, anmals or thngs, mproper nstallaton, adjustment, mantenance and mproper use Ths manual s part of the devce and therefore must be carefully retaned and always accompany the regulator even f gven to another owner, or transferred on another plant. n case of damage or loss, contact Agentech Srl Avod usng the devce n places subject to vbratons or crashes Avod usng the devce n places wth temperatures above 45 C or below -10 C Protect the devce from excessve humdty SAFETY RULES h h 6 6 Any mantenance or settng of the devce before dsconnectng t from the mans supply by settng the plant s man swtch to ts OFF poston, s forbdden. t s forbdden to dsassemble the devce t s forbdden to modfy the devce t s forbdden to keep the regulator n contact wth flammable materals n the event of lqud spllng on the devce, mmedately dsconnect the power supply by placng the man swtch of the plant to ts OFF poston Do not occlude the ventlaton openngs of the devce t s forbdden attempt to repar the equpment by yourself. Always contact Agentech srl Techncal Assstance Servce

6 USAGE OF THE GENUS POWER COMB The GENUS POWER COMB s an automatc lght flux regulator and s desgned to reduce the voltage on the lamps n publc and prvate lghtng systems. The benefts of ths regulator are: Energy savng Reducng the costs of electrcty supply Longer lfe of lamps reducton of mantenance costs Power emssons of CO 2 Reduced lght polluton The man felds of applcaton are as follows: Publc and prvate buldngs ndustres Hosptals Sports plants Exhbtons Shoppng Centers Publc Lghtng Parkngs and squares Archtectural and monumental lghtngs The types of lamps wth whch you have the most sgnfcant advantages are: Mercury vapors lamps Hgh pressure sodum lamps Low pressure sodum lamps Halogen lamps Lght bulbs Metal halde lamps Fluorescent lamps wth electromagnetc ballast DESCRPTON OF THE REGULATOR The man feature of the GENUS POWER COMB flux regulators s to down the harmonc dstorton of the power lne. These devces consst of an autotransformer and ntellgent electroncs that provdes the voltage values at the output. You can set up to eght dfferent voltage levels by the control panel, whch s very easy and ntutve and placed on the front of the regulator. From the same panel you can set the WARM UP tme and the BYPASS state. Once set the values, the regulator operates automatcally wthout the need for further acton. Lke all Agentech flux regulators, the COMB also can work wth all common types of electromagnetc ballast lamps. The bypass state can also be trggered by an external command. The COMB can be nstalled n power panels or wall mountng, whle mantanng an P20 protecton level, and s extremely versatle thanks to ts sze and weght. GENUS POWER COMB regulators are equpped wth: Control Panel for settngs and sgnals on operaton modes and falures bracket for quck DN ral or wall mountng Quck-clampng connector and protecton shell for wall mountng REGULATOR S PARTS

7 1. CONTROL PANEL 7. LABEL FOR GROUNDNG 2. DENTFCATON PLATE 8. LOWER VENTLATON OPENNGS 3. MOUNTNG BRACKETS 9. QUCK CONNECTOR 4. SDE VENTLATON OPENNGS 10. PLATE WTH CONNECTOR NSTRUCTONS 5. MULT-POLAR OUTLET 11. TOP VENTLATON OPENNGS 6. SCREW FXNG THE GROUND WRE 12. BLOCKS FOR RAL SCREW MOUNTNG FRONTAL VEW

8

9 SPECFCATONS PARAMETER COMB 6 COMB 10 COMB 12 Power 1Ph + N + PE 230V ±15% - 50Hz Max output current 6ARMS 10ARMS 12ARMS Max power 1 380VA 2 300VA 2 760VA Thermal Dsspaton Adjustment levels [%VN] 100% 83% VN Mnmum load control 80W Performance 99% nsulaton class Class EMC complance - Operatng temperature From 10 C to +45 C Storage temperature from 25 C to +75 C Humdty Up to 90% wthout condensng Protecton level P20

10 MEASURES WEGHT COMB6 COMB10 COMB12 4,8Kg 5,8Kg 6,8Kg

11 NSTALLATON The GENUS POWER COMB regulators can be nstalled nto power panels on both omega bar nsde cabnets and wall mount. Fg. X. Subttle Fg. X. Subttle 6 6 Verfy that the electrcal protecton level of the devce s approprate to the characterstcs of the room where s to be nstalled t s forbdden to mount the devce outdoor f not properly protected Verfy that the power panel where to house the regulator has adequate heat dsspaton characterstcs. Do not occlude the ventlaton openngs of the devce Consder an adequate room needed for accessblty to the regulator for setup and mantenance operatons Fg. X. Subttle Fg. X. Subttle

12 OUTPUT CONNECTOR The GENUS POWER COMB provdes a quck connector wth 5-termnal screw tghtenng of the cables and ther protectve shells. Fg. Exploded vew of the connector For wall mount you have to protect the connector wth ts approprate shells. h 6 f protecton shells wll not be used you wll have drect access to the 230VAC Do not use sngle core cables for connectng the devce wth the protectve shell Use H05VV-F flexble mult-core cable To ensure good tghtenng use a mult-core cable wth fnshed dameter 9mm Fg. Connector wth shell For nstallaton nsde power panels s not necessary the use of protectve shells. The regulator can be grounded by connectng the cable to the GND screw.

13 WRES 1. HEARTH PROTECTON. For use n wall mountng 2. BYPASS CONTROL. To be used for bypass actvaton by remote devces 3. NEUTRAL. Neutral, common for nput and output lnes 4. OUTPUT LNE. Power load 5. NPUT LNE. Power equpment GND. Fxng screw for the ground connecton, sutable for nstallaton n power panels. CRMP AND WRES SECTONS A. Wre secton wth tp for detachable connector B. Wre secton wthout tp for detachable connector C. Eyelet termnal for GND screw connecton D. Fork termnal for GND screw connecton

14 CONNECTON t s requred to use a crcut breaker, dsconnect swtch. Swtches used to dsconnect a transformer from the supply, must dsconnect all poles and provde a complete separaton for the overvoltage category consdered. Always use cables wth secton 1.5 mm ² and follow the L (Phase) and N (Neutral) connecton scheme Create a good ground connecton, always makng sure ths cable s always longer than the others so that s the last to come off f subject to any stress. Protect the accessblty to the quck connector after nstallaton also. The manufacturer s not responsble for any damage caused by the lack of groundng or nobservance of the wrng dagrams

15 TYPCAL WRNG DAGRAM - SNGLE PHASE TYPCAL WRNG DAGRAM - THREE PHASE

16 OPERATNG PRNCPLES The operaton prncples of the GENUS POWER COMB can be summarzed n the followng fgure: The autotransformer has 8 outputs, each gvng a dfferent voltage. From the control panel you can set the desred voltage level. Power devces are drven through the mcroprocessor control unt, so that the regulator s output s drectly connected to the output wth ts voltage level set. The output s drectly connected to the 230V nput lne, wth a varaton that can range up to ± 15%, both n "BYPASS" mode and "WARM UP" cycle. As t s used a transformer, the voltage on the center output s drectly affected by the varaton of the nput voltage VN. For example, f there s a 5% ncrease of the nput lne, there wll be a resultng voltage ncrease of the output lne. The regulator makes the "WARM UP" cycle after ts start, and then moves nto the "SAVNG " mode whch falls n the area of savngs. The tme duraton of the "WARM UP" cycle s set and dsplayed on the control panel under the "WARM UP TME" secton. The output voltage level s set and dsplayed on the control panel under the " RATO SELECTON secton. (REFER TO THE PARAGRAPH)

17 FRST START Before swtchng on and perform the functonal test of the regulator, t s essental to check all electrcal wrngs are properly made (REFER TO THE PARAGRAPH) Make sure the ground wre s properly connected Check the presence of the protectve devce upstream the unt, makng sure t meets the requrements stated on the plate of the regulator Check the tghtness of the connector s screws. Power up the regulator only after havng checked the above lst. f everythng s ok, the lamps wll lght up mmedately. The regulator performs the "WARM UP " cycle. Lamps are drectly connected to the 230V nput lne. The green "POWER" led, the yellow "WARM UP" led and the yellow "BYPASS" led should lght up on the control panel. Both the red "WARM UP TME" and the "RATO SELECTON" leds wll swtch on, accordng to the manufacturer test. The GENUS POWER COMB goes nto savng mode after havng fnshed the warm-up cycle, brngng ts output to the voltage set on the "RATO SELECTON" parameter, correspondng to the lghtng red led. The green "SAVNG" led starts lghtng and the yellow "WARM UP" and "BYPASS" leds swtch off. The regulator remans n ths condton untl next restarts or settngs. The "WARM UP TME" and "RATO SELECTON" values set by the manufacturer are not always the same. f there are any anomales, see the "TROUBLESHOOTNG" paragraph.

18 SETTNG THE WARM UP CYCLE There are types of lamps or partcular nstallaton condtons (e.g. hgh length of the lne that causes sgnfcant voltage drops), whch make mpossble for the lghtng of lamps at voltages below a certan threshold. For ths reason, after ts swtchng on, the regulator starts the "WARM UP" cycle durng whch the lamps are connected drectly to the 230V ± 15% lne voltage, whch guarantees ther regular lghtng. The duraton of ths cycle s equal to the tme correspondng to the "WARM UP TME" level sgnaled by the red led swtched on, and s set by pressng the key n the "WARM UP" zone on the control panel. WARM UP TME secs mns mns mns. f you press ths key repeatedly, you enable the next level untl you return perodcally to the level 1 ( etc). Changes n the warm-up tme made durng the warm up cycle have no nstant effect, but only after the next tme the regulator wll be swtched on. Durng ths phase, the yellow "WARM UP" and "BYPASS" leds reman smultaneously lt. f you connect loads to the output of the regulator after ts warm-up cycle, the voltage settng may not be suffcent to turn on some types of lamps. f you want to ext from the warm-up cycle before the set tme, just press the bypass "SET/RESET" key, so that the regulator goes on the savng mode.

19 SETTNG THE "RATO SELECTON" VOLTAGE LEVEL After the warm-up cycle, the regulator goes n "SAVNG" mode. The yellow "WARM UP" led turns off and the green "SAVNG" led lt. n ths state the regulator output s at the voltage correspondng to the level showed by the red led n the "RATO SELECTON" area on the control panel. Act on the two keys to change the level as shown below. RATO SELECTON VOUT V% Wa% Wd% % 36% % 34% % 32% % 30% % 28% % 25% % 23% % 21% V% Output voltage n% of the VN value Wa% Percentage of power savngs when usng halogen lamps Wd% Percentage of power savngs when usng dscharge lamps Pressng the key takes you to the lower level, whle the key takes you to the next level. When you set a new level, the value on the output voltage changes after a few seconds. The voltage values correspondng to the "RATO SELECTON" levels, refer to an deal 230VAC nput voltage. Varatons of the nput voltage correspond to varatons n output voltage.

20 BYPASS The regulator does not operate any energy savngs when n BYPASS mode. n fact, when t goes n ths mode, the green "SAVNG" led turns off and the yellow "BYPASS" led automatcally lt. n ths condton, the regulator output s drectly connected to the nput lne at 230V ± 15%. To enable ths mode manually, just press the key n the "BYPASS" zone. The key works n "toggle" mode then, f the regulator s n "SAVNG" mode, by pressng ths key t goes n "BYPASS" mode. nstead, f the regulator s n "BYPASS" mode t goes n "SAVNG" mode. Durng the warmup cycle, the GENUS POWER COMB automatcally enables the "BY PASS" mode. The mnmum tme spent n one of these two modes ("BYPASS" and "SAVNG") s about 3 seconds. You wll not obtan any change f you press the key before 3 seconds. t s also possble to remotely force the bypass state, usng an external control devce.

21 REMOTE BYPASS CONTROL f you need to force the bypass mode by usng auxlary devces, you can use the BYPASS contact. n the basc dagram, "K1" s the contact of a relay or contactor. The regulator remans n "SAVNG" mode when t s open, and the output voltage s equal to the value set n the "RATO SELECTON" parameter. f the contact s closed, the "BYPASS" termnal s drectly connected to the nput phase. The regulator mmedately goes n "BYPASS" mode, and the yellow "BYPASS" led lt and the green "SAVNG" led turns off. The output s drectly connected to the nput lne. The regulator s n bypass mode all the tme that the contact "K1" s closed.

22 ALERTS AND FAULTS FAULTS All leds and lghts are off POSSBLE CAUSES/SOLUTON No power supply lne; Power connector s ncorrectly nserted; Measure the nput lne voltage wth a mult-meter; Check the nserton of the plug connector; The FAULT led s lt, all others are off, lamps are lt. Protecton fuse broken nterventon by the thermal resstance of the transformer; Check the fuse and replace f broken, wth one havng the same characterstcs lsted on the plate; CONTACT THE SERVCE CENTRE f the machne stll does not properly work; All leds are off, the lamps are lt No power at the control crcuts (+12 or +5); F2 resettable fuse nterventon (wat some mnutes); ncorrect connecton between power board and control; CONTACT THE SERVCE CENTRE The voltage on the lamps does not match the selected rato The U1 ntegrated crcut on the power board s not properly nserted; Contact pasted on one of the swtchng relays; CONTACT THE SERVCE CENTRE The lamps are swtched off, on one of the 8 selected ratos. Autotransformer termnal loose on ts output; CONTACT THE SERVCE CENTRE f faults cannot be resolved wth the above gudelnes contact the servce by communcatng: the problem the devce model the seral number 6 Do not attempt to dsassemble or repar the regulator by yourself. Always contact your Agentech Srl Servce Center. 6 Never call unauthorzed techncans and do not replace parts wth ones that do not comply Tamperng or repar by unauthorzed personnel wll permanently vod the warranty