User Manual TITANIUM. COMPACT SATELLITE HEADEND Ref

Transcription

1 User Manual TITANIUM COMPACT SATELLITE HEADEND Ref

2 Cntents 1. Intrductin Prduct descriptin Typical installatin Package cntents Prduct dimensins Munting Cnfiguring the Titanium using the web interface... 5 MINIMAL SYSTEM REQUIREMENTS... 5 LOGGING IN TO THE DEVICE... 5 CONNECTING THE MODULE(S) TO A NETWORK... 7 DEVICE CONFIGURATION Lgin Overview Input Output CAM Technical Specificatins Safety Instructins Cnditins f warranty N part f this manual may be cpied, reprduced, transmitted, transcribed r translated int any language withut permissin. Unitrn reserves the right t change the specificatins f the hardware and sftware described in these manuals at any time. Unitrn cannt be held liable fr any damages resulting frm the use f this prduct. Specificatins are subject t change withut ntice. 01/19 Unitrn - Frankrijklaan 27 - B-8970 Pperinge - Belgium T F sales@unitrngrup.cm 1

3 1. INTRODUCTION 1.1. Prduct descriptin The Titanium is a cmpact satellite headend with 4 (Ref. 8700) r 8 (Ref. 8701, 8703) tuners. It is a transmdulatr with 4 utput MUXs (DVB-T/DVB-C) r 8 utput MUXs (Ref. 8703). The standalne mdule with built-in pwer supply allws fr very fast installatin. The Titanium has 2 CI slts fr CAM cards (Ref has 4 CI slts). ATTENTION! The Titanium shuld be wall-munted. Fr ventilatin purpses, leave a minimum f 15 cm arund all sides f the mdule Typical installatin The Titanium can be used t prvide high quality satellite televisin in a wide range f prjects, bth in the hspitality as in the residential market. Typical buildings r infrastructures where the Titanium can be used include, but are nt limited t: - Htels, hstels, bed and breakfasts, hliday parks - Hspitals, rest hmes, prisns - Large and small multi-dwelling units with an internatinal public, settlements - Maritime infrastructure such as bats, yachts, barges 2

4 1.3. Package cntents - 1 x Titanium (ref r 8701 r 8703) - 1 x 75 Ohm terminatrs - 1 x Mains cable (1,80 m) 1.4. Prduct dimensins 3

5 1.5. Munting Prper installatin is critical t system perfrmance. It is particularly imprtant t install the Titanium crrectly in rder t receive and distribute ptimal signal quality. - Munt the Titanium t a wall in a well ventilated and cl rm. Fr ventilatin purpses, leave a minimum f 15 cm arund all sides f the mdule. - Plug the 4 satellite cables in the SAT 1-4 prts. - If the Titanium shuld receive RF signal frm anther Titanium r an external surce, cnnect a caxial cable t the RF IN prt. If nt applicable, insert a 75 Ohm terminatr in the RF IN prt. - Cnnect the caxial TV netwrk t the RF ut prt. - If the Titanium is cnfigured t read CAM cards, insert 1, 2, 3 r 4* CAM cards** and smart cards* in the slts n the backside f the Titanium. (* depending n Titanium type) (**Nt included with the Titanium). - Pwer the Titanium with the mains cable. Once it is pwered, a RED POWER LED will start blinking. When the LED stps blinking and turns BLUE, the mdule is cmpletely bted and ready fr cnfiguratin. This will take apprximately 4 minutes. - Fr cnfiguratin f the mdule, the web interface must be accessed. Therefre, plug an Ethernet cable in the cntrl prt, and the ther end in a cmputer. - Mre infrmatin abut cnfiguratin f the Titanium mdule can be fund in the next sectin 4

6 2. CONFIGURING THE TITANIUM USING THE WEB INTERFACE MINIMAL SYSTEM REQUIREMENTS The WebGUI is supprted by the fllwing web brwsers: - Ggle Chrme - Mzilla Firefx - Internet Explrer - Safari Make sure t use the mst recent versin f the brwser. When using a different brwser, we cannt guarantee a crrect functining f the interface. LOGGING IN TO THE DEVICE Plug ne end f an Ethernet cable in the cntrl prt and the ther end in a cmputer. Once the Titanium is pwered and fully bted, the mdule is reachable and ready t be cnfigured. Fr a mre reliable WebGUI cnnectin, we advise t use fixed IP r DCHP. Therefre, carefully fllw the steps belw: Set the cmputer t btain an autmatic IP address as explained in the fllwing prcedure (fr Micrsft Windws10 ) Navigate t the Cntrl Panel (Start Cntrl Panel). Enter the Netwrk and Sharing Center and g t the Adapter Settings Right-click n the Lcal Area Cnnectin and chse Prperties. Duble click Internet Prtcl Versin 4 (TCP/IPv4) t enter the IP settings f yur adapter. Make sure the Obtain an IP address autmatically checkbx is selected. Click OK t save the settings. 5

7 Open yur web brwser, and g t: The web interface f the Titanium will nw pen. G t Management Prt Tick ff Obtain IP address frm DHCP Chse an IP Address, fr instance: Press Apply G back t Lcal Area Cnnectin Prperties, select Internet Prtcl Versin 4 (TCP/IPv4) t enter the IP settings f yur adapter Tick Use the fllwing IP address Fill in the IP address yu chse in the Titanium Management Prt, but make sure that the last grup f digits is different, fr instance: Open yur webbrwser and g t Nw a stable cnnectin is guaranteed 6

8 Cnnecting the mdule(s) t a netwrk with DHCP T cnnect the mdule(s) t a netwrk, g t the Management Prt in the web interface. Tick Obtain IP address frm DHCP and give each Titanium a unique hstname (fr instance: Click apply t cnfirm. Nw the mdule can be accessed via (fr instance: r check yur DHCP server fr IP address. DEVICE CONFIGURATION It is f utmst imprtance that yur device is cnfigured in a right way in rder t make the Titanium installatin successful. T d s, fllw the belw mentined steps carefully. 1. Lgin After the web interface pens (see previus step), the hme page with an verview f active services appears. On this screen, yu see infrmatin abut the utput MUXs, the CAM status and the chsen TV services. In the tp right crner, yu will see the device status. If the status LED is green, there are n alarms. When yu mve yur cursr ver the status LED, the alarm status will appear. By clicking n lgin, yu can lg in t the mdule. Use the passwrd admin.! change the passwrd as sn as yu lg in t the mdule via Management Prt! After lgging in, the Overview windw will appear again. The menu structure f the web interface can be fund in the left clumn. 7

9 2. Overview The fllwing actins are critical fr ptimal system perfrmance: Infrmatin: The flwing infrmatin can be fund here: Device Type, Device Name, Device ID, Serial Number, Firmware Versin, Hardware Versin, Device Features and Device Temperature Preferences: Chse dbm r dbµv as level unit. Click APPLY t cnfirm Management prt: Define the hstname and IP settings f yur management prt: Here yu can cnfigure the hstname f the mdule. This name can be used t access the mdule by simply typing it int yur brwser as the address and surf t it. This is mre cnvenient than using the IP address. Change yur passwrd t secure yur mdule fr unauthrized users. Dynamic DNS: cnfiguratin fr remte access t register a fixed IP address Firmware Upgrade: Click n the Brwse buttn, and pen the upgrade file (.upg). Click Upgrade t send the file t the device, this will install the new firmware n the device. Cnfiguratin Chse the cnfiguratin f yur Titanium: DVB-T r DVB-C. Press APPLY t cnfirm - Device Settings: G t this tab if yu want t imprt a settings file frm anther mdule (click n chse file and select the.exp file n yur cmputer), r exprt a settings file (s yu can later uplad it t anther mdule). This tab can als be used t stre and restre the device settings - Reset device: If there is an issue, g t the Reset Device tab t rebt yur Titanium. Via this tab yu can als reset certain settings r restre the default 8

10 cnfiguratins f yur Titanium. All settings can be reset t default by means f a factry reset. The Titanium can als be manually reset. This can be dne by inserting a pin (e.g. a paperclip) in the small pening in the frnt plate f the Titanium, between the pwer and alarm LEDs. By pressing this buttn less than 2 secnds (LED abve cntrl prt will turn RED), the device will rebt By pressing this buttn lnger than 5 secnds (LED abve cntrl prt will blink GREEN), the device will rebt, the IP settings will be reset and the passwrd will be reset t the default passwrd admin. - Lgut: When yu are finished cnfiguring the Titanium, click lgut t secure the web interface fr unauthrized users. 9

11 3. Input 3.1 Define the LNB settings (INPUT > LNB) Label: custm label fr each input (e.g. VLw, r ASTRA 19.2VLw, ) Vltage: The LNB vltage t select the plarizatin 13V: Vertical plarizatin 18V: Hrizntal plarizatin Extended Vltage: Add 1V t the LNB vltage t cmpensate the cable lsses fr lng caxial cables. Tne: LNB tne t select lw/high band ON: high band OFF: lw band DiSEqC : cntrl f a DiSEqC switch (A/B/C/D) Band: Satellite band Ku-band C-band Enable: d nt frget t enable the LNB input, this is disabled by default) Press APPLY t cnfirm the parameters. 10

12 3.2 Define the settings fr each f the tuners (INPUT > TUNER) Input Selectin: this refers t the LNB inputs; make sure the transpnder frequencies yu chse crrespnd t the right plarity f the LNB inputs Frequency (Mhz): chse the frequency f the transpnder yu want t receive Baud Rate (kbd): chse the baud rate f the transpnder signal yu want t receive Mdulatin: chse between DVB-S and DVB-S2 Enable: click the tick bx t enable the tuner (this is disabled by default) Check the lck status, signal level, signal quality and signal t Nise t see if the tuner lcks n the selected transpnder Press APPLY t cnfirm the parameters. The mdule will nw set the tuner t this frequency. Wait until the crrect parameters are laded. When the tuner is able t lck n the frequency, the services list frm this transpnder will be shwn. Services list: after a tuner is lcked, the services will appear. A RED lck indicates that the service is scrambled, a GREEN lck indicates that the service is clear Netwrk parameters: this is an verview f the fllwing infrmatin: Name, ONID, TSID, NID and versin 11

13 4. Output 4.1 Set all the Mux (OUTPUT > MUX) Frequency(kHz): Here yu can select the frequency yu want t transmit n. Fr DVB-T: t , fr DVB-C: t Bandwidth (DVB-T): Chse the desired bandwidth. Baud Rate (DVB-C) (MBd): chse the baud rate f the transpnder signal yu want t utput Cnstellatin: Chse the type f cnstellatin yu want t use. (64QAM, 16QAM, QPSK) Level(dBm): define the level f RF (between -25 t -40) Enable: click the tick bx t enable the tuner (this is disabled by default) Press APPLY t cnfirm the Mdulatin Settings. Transprt Stream Settings: Status: TSID: chse a identifier fr the Transprt Stream (value between 1 and 65535). Press APPLY t cnfirm the Transprt Stream Settings. The bitrate bar shws the current bitrate f the selected multiplex. Depending n the mdel, the Titanium dispses f 4 multiplexes. The maximum bitrate per MUX is 30 Mbps (DVB-T) r 50 Mbps (DVB-C). It is hwever advisable t keep a buffer f 4 Mbps, t prevent pssible verflw (bitrate f services can fluctuate in time). Select anther multiplex by clicking n the tabs n tp f the page. Service Settings: Tuner: chse the input stream yu set in INPUT Name: chse the service CI: chse the ruting f the service: FTA (Free-t-Air) CAM 1 CAM 2 Pririty: prvides the pssibility t priritize sme services (e.g. Primetime services) t guarantee better quality n TV in case f spradic bandwidth verflw due t thrughput limitatin f the multiplex. It is advised nt t exceed 30% f ttal number f services t be priritized fr each multiplex. New SID: Change the Service Identifier t remap the SID LCN: Give a Lgical Channel Number t rder the number f channels n the end-devices Individual PID filtering: click the \/ t drp dwn the menu here individual PIDs can be blcked per service Click the + sign t add the service t the list Define this fr each service in the list. After a service is changed, it can be saved (save icn) r deleted (bin ic) Each service can be saved r deleted. Press UPDATE t cnfirm the parameters. PID Settings: Blck thers: Tick this bx and press APPLY t blck all irrelevant prgram infrmatin data. Only the essential PID will be passed thrugh: vide, audi, CAS, 12

14 4.2 Define the utput netwrk (OUTPUT > NETWORK) ONID: The Original_Netwrk_ID (ONID) is defined as the unique identifier f a netwrk, check the spreadsheets n t find yur crrect ONID NID: Chse yur Netwrk ID Netwrk Name: Set yur netwrk name Versin: set the versin f the netwrk (value between 0 and 31) Private Data Specifier: chse between EACEM ITC NORDIG Press APPLY t cnfirm the parameters. 13

15 5. CAM 5.1 Set the CAM cnfiguratins fr the Titanium (CAM > CAM ) CAM settings Type: Defines type f CAM mdule Select lw-speed (default) fr legacy CAM mdule that can run up t 50 MBps Select high-speed fr secnd generatin CAM mdule that can run up t 100 MBps Watchdg: The watchdg mnitrs the scrambling status f all services ging thrugh the CAM. In case ne r mre services are n lnger descrambled, the watchdg will prceed t the reset f the CAM mdule t try t restre the descrambling f the service(s). Imprtant: Activate this feature nly nce all services are prperly descrambled by the CAM mdule. Enable: Click ENABLE t activate the CAM (default). Press APPLY t cnfirm the parameters. Reference Transpnder Reference Transpnder: It is necessary t enable and select a reference transpnder in the CAM menu (fr each CAM individually). The CAM mdule needs authrizatin t descramble services. Select the reference transpnder with authrizatin infrmatin fr each CAM individually. Press APPLY t cnfirm the parameters. CAM Menu: the CAM menu will appear here when inserted. Click the tabs fr mre inf 14

16 3. TECHNICAL SPECIFICATIONS Input: QPSK/8PSK (DVB-S/S2) Inputs - 4 satellite bands 1 x RF in Tuners - 4 tuners (4 transpnders) (Ref. 8700) 8 tuners (8 transpnders) (Ref. 8701) 8 tuners (8 transpnders) (Ref. 8703) Frequency range MHz Level dbm -55 t -25 Bandwidth MHz 36 Mdulatin - DVB-S2: QPSK, 8PSK / DVB-S: QPSK DC remte pwer at RF input Integrated multiswitch - 13 V/18 V/22 khz - Yes, allws flexible ruting f satellite prgrams t multiplexes (QAM r QOFDM) Cnfiguratin - Built-in webserver accessible via management prt Encded prgrams - Frm all 4 r 8 tuners. Can be ruted thrugh 1, 2, 3 r 4 CAMs and can be decded using multi-service CAMs Output: RF Outputs - 1 with 4 MUXs (DVB-T r DVB-C) (Ref ) 1 with 8 MUXs (DVB-T r DVB-C) (Ref. 8703) DVB-T utput Mbps Up t 31.7 / MUX DVB-C utput Mbps Up t 51.3 / MUX General Pwer cnsumptin W 22 (excl. external LNBs) CI slts - 2 (Ref ) 4 (Ref. 8703) Dimensins cm 34.5 x 7 x 18.2 Operating temperature C 0 t

17 4. SAFETY INSTRUCTIONS Read these instructins carefully befre cnnecting the unit T avid any risk f verheating: Install the unit in a well aery lcatin and keep a minimum distance f 15 cm arund the apparatus fr sufficient ventilatin D nt place any items such as newspapers, table-clths, curtains, n the unit that might cver the ventilatin hles. D nt place any naked flame surces, such as lighted candles, n the apparatus D nt install the prduct in a dusty place Use the apparatus nly in mderate climates (nt in trpical climates) Respect the minimum and maximum temperature specificatins T avid any risk f electrical shcks: Cnnect apparatus nly t scket with prtective earth cnnectin. The mains plug shall remain readily perable Pull ut pwer plug t make the different cnnectins f cables T avid electrical shck, d nt pen the husing f adapter. Maintenance Only use a dry sft clth t clean the cabinet. D nt use slvent Fr repairing and servicing refer t qualified persnnel. Dispse accrding t yur lcal authrity s recycling prcesses 16

18 5. CONDITIONS OF WARRANTY Unitrn N.V. warrants the prduct as being free frm defects in material and wrkmanship fr a perid f 24 mnths starting frm the date f prductin indicated n it. See nte belw. If during this perid f warranty, the prduct prves defective, under nrmal use, due t defective materials r wrkmanship, Unitrn N.V, at its sle ptin, will repair r replace the prduct. Return the prduct t yur lcal dealer fr reparatin THE WARRANTY IS APPLIED ONLY FOR DEFECTS IN MATERIAL AND WORKMANSHIP AND DOES NOT COVER DAMAGE RESULTING FROM: Misuse r use f the prduct ut f its specificatins. Installatin r use in a manner incnsistent with the technical r safety standards in frce in the cuntry where the prduct is used Use f nn-suitable accessries (pwer supply, adapters...). Installatin in a defect system. External cause beynd the cntrl f Unitrn N.V. such as drp, accidents, lightning, water, fire, imprper ventilatin THE WARRANTY IS NOT APPLIED IF: Prductin date r serial number n the prduct is illegible, altered, deleted r remved. NOTE The prduct has been pened r repaired by a nn-authrized persn. Date f prductin can be fund in the prduct s serial number cde. The frmat will either be YEAR W WEEK (e.g., 2018W01 = year 2018 week 1) r YYWW (e.g., 1447 = year 2014 week 47). UNITRON NV Frankrijklaan 27 B-8970 Pperinge Belgium T F sales@unitrngrup.cm 17