H3CR. Multifunctional Timer Twin Timer Star-delta Timer Power OFF-delay Timer H3CR-A H3CR-AS H3CR-AP H3CR-A8 H3CR-A8S H3CR-A8E H3CR-G.

Transcription

1 Solid-sae Timer H3CR Please read and undersand his caalog before purchasing he producs. Please consul your OMRON represenaive if you have any quesions or commens. Refer o Warrany and Applicaion Consideraions (page 52), and Safey Precauions (page 22, 44, 51). DIN mm Mulifuncional Timer Series Conforms o EN and IEC kv/2 for Low Volage, and EMC Direcives. Approved by UL and CSA. Lloyds/NK approvals. Six-language insrucion manual provided. Broad Line-up of H3CR Series H3CR H3CR-A H3CR-F H3CR-G H3CR-H Mulifuncional Timer Twin Timer Sar-dela Timer OFF-delay Timer H3CR-A H3CR-AS H3CR-AP H3CR-A8 H3CR-A8S H3CR-A8E 11-pin model 8-pin model 8-pin wih insananeous conac oupu model H3CR-F H3CR-FN H3CR-F8 H3CR-F8N 11-pin model 8-pin model H3CR-G8L H3CR-G8EL 8-pin model H3CR-HRL H3CR-H8L H3CR-H8RL 11-pin model 8-pin model Noe: H3CR-AS, H3CR-A8S: Transisor oupu models Conens Solid-sae Timer H3CR-A... 2 H3CR-F H3CR-G H3CR-H Common o ALL Timers Operaion Accessories Safey Precauions

2 Solid-sae Muli-funcional Timers H3CR-A Muliple Operaing Modes and Muliple Time Ranges. DIN 48 x 48-mm Mulifuncional Timer. A wide AC/DC power supply range grealy reduces he number of imer models kep in sock. A wide range of applicaions wih muliple operaing modes, eigh modes for 11-pin models and five modes for 8-pin models. Ecological design wih reduced curren consumpion. Easy sequence checking wih insananeous oupus for a zero se value. Lengh of 75 mm or less when panel-mouned wih a P3G-08 Socke (H3CR-A8E, 100 o 240 VAC, 100 o 125 VDC) PNP inpu models available. Sandards: UL, CSA, NK, LR, CCC, EN , and CE Marking. For he mos recen informaion on models ha have been cerified for safey sandards, refer o your OMRON websie. Model Number Srucure Model Number Legend Noe: This model number legend includes combinaions ha are no available. Before ordering, please check he Lis of Models on page 3 for @ Number of Pins None: 11-pin models 8: 8-pin models 2. Inpu Type for 11-pin Models None: No-volage inpu (NPN ype) P: Volage inpu (PNP ype) 3. None: Relay oupu (DPDT) S: Transisor oupu (NPN/PNP universal use) E: Relay oupu (SPDT) wih insananeous relay oupu (SPDT) 4. Suffix 301: Double ime scale (range) models (0.1 s o 600 h) 5. Supply Volage AC/ DC: 100 o 240 VAC/100 o 125 VDC 24-48AC/12-48DC: 24 o 48 VAC/12 o 48 VDC 24-48AC/DC: 24 o 48 VAC/VDC (Only for H3CR-A8E) 2

3 H3CR-A Ordering Informaion Lis of Models Noe: 1. Specify boh he model number and supply volage when ordering. Example: H3CR-A AC/ DC Supply volage 2. The operaing modes are as follows A: ON-delay D: Signal OFF-delay B: Flicker OFF sar E: Inerval B2: Flicker ON sar G: Signal ON/OFF-delay C: Signal ON/OFF-delay J: One-sho 11-pin Models Conac Transisor (Phoocoupler) Supply volage Inpu ype Time range Operaing mode (See noe 2) 8-pin Models Conac Transisor (Phoocoupler) 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC No-volage inpu 0.05 s o 300 h Eigh muli-modes: A, B, B2, C, D, E, G, J Volage inpu Eigh muli-modes: A, B, B2, C, D, E, G, J Model (See noe 1.) H3CR-A H3CR-AP No-volage inpu 0.1 s o 600 h H3CR-A s o 300 h H3CR-AS Supply volage Inpu ype Time range Operaing mode (See noe 2) Time-limi conac and insananeous conac 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 24 o 48 VAC (50/60 Hz)/ 12 o 48 VDC 100 o 240 VAC (50/60 Hz)/ 100 o 125 VDC 24 o 48 VAC/VDC (50/60 Hz) No-inpu available 0.05 s o 300 h Five muli-modes: A, B, B2, E, J ( supply sar) Model (See noe 1.) H3CR-A8 0.1 s o 600 h H3CR-A s o 300 h H3CR-A8S H3CR-A8E 3

4 Accessories (Order Separaely) H3CR-A Adaper, Proecive Cover, Hold down Clip, Seing Ring and Panel Cover Name/specificaions Flush Mouning Adaper Y92F-30 Y92F-73 *1 Y92F-74 *1 Proecive Cover Y92A-48B *2 Hold-down Clip (Sold in ses of For PF085A Socke Y92H-8 wo) For PL08 or PL11 Sockes Y92H-7 Seing Ring A Y92S-27 *3 Seing Ring B and C Y92S-28 *3 Panel Cover Ligh gray (5Y7/1) Y92P-48GL *4 Black (N1.5) Y92P-48GB *4 Models *1 The Y92A-48B Proecive Cover and he Y92P-48G@ Panel Cover can no be used a he same ime wih he Y92F-73/-74 Flush Mouning Adaper. *2 The Y92A-48B Proecive Cover is made from hard plasic. Remove he Proecive Cover o change o se value. The Y92F-73/-74 Flush Mouning Adaper and he Y92P-48G@ Panel Cover canno be used a he same ime wih Y92A-48B Proecive Cover. *3 The Y92S-27/-28 Seing Ring canno be used alone. I mus be used ogeher wih he Y92P-48G@ Panel Cover. *4 The Y92A-48B Proecive Cover and he Y92F-73/-74 Flush Mouning Adaper canno be used a he same ime wih he Y92P-48G@ Panel Cover. Sockes Timer Round Sockes Pin Connecion Terminal Models 11-pin Fron Connecing DIN rack mouning P2CF-11 DIN rack mouning P2CF-11-E (Finger-safe ype) Back Connecing Screw erminal P3GA-11 Solder erminal PL11 Wrapping erminal PL11-Q PCB erminal PLE pin Fron Connecing DIN rack mouning P2CF-08 DIN rack mouning P2CF-08-E (Finger-safe ype) DIN rack mouning PF085A Back Connecing Screw erminal P3G-08 Solder erminal PL08 Wrapping erminal PL08-Q PCB erminal PLE08-0 Noe: 1. The P2CF-@@-E has a finger-proecion srucure. Round crimp erminals canno be used. Use forked crimp erminals. 2. The P3GA-11 and P3G-08 Socke can be used ogeher wih he Y92A-48G Terminal Cover o implemen finger proecion. 3. For deails, refer o your OMRON websie. Terminal Cover Applicaion Model Remarks For back connecing socke Y92A-48G For P3G-08 and P3GA-11 Noe: For deails, refer o your OMRON websie. 4

5 H3CR-A Specificaions General Iem H3CR-A/-AS/-A-301 H3CR-AP H3CR-A8/-A8S/-A8-301 H3CR-A8E Operaing mode A: ON-delay B: Flicker OFF sar B2: Flicker ON sar C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval G: Signal ON/OFF-delay J: One-sho *1 The inernal s are opically isolaed from he oupu. This enables universal applicaion as NPN or PNP ransisor. For deails, refer o your OMRON websie. *2 CCC cerificaion requiremens Time Ranges Noe: When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. For deails, refer o your OMRON websie. Sandard (0.05-s o 300-h) Models A: ON-delay (power supply sar) B: Flicker OFF sar (power supply sar) B2: Flicker ON sar (power supply sar) E: Inerval (power supply sar) J: One-sho (power supply sar) Pin ype 11-pin 8-pin Inpu ype No-volage inpu Volage inpu --- Time-limi oupu ype H3CR-A/-A8/-AP/-A-301/-A8-301: Relay oupu (DPDT) H3CR-AS/-A8S: Transisor oupu (NPN/PNP universal) *1 Insananeous oupu ype --- Mouning mehod DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds, CCC: GB/T *2 Conforms o EN and IEC (VDE0110) 4kV/2. caegory according o EN for Timers wih Conac s. caegory according o EN for Timers wih Transisor s. Recommended fuse Raed operaing volage Ue Raed operaing curren Ie Raed insulaion volage Raed impulse wihsand volage (aliude: 2,000 m max.) Condiional shor- curren Conac : (250 VAC, 5 A), manufacured by Lielfuse Transisor : (250 VAC, 100 ma) manufacured by Lielfuse Conac : AC-15: Ue: 250 VAC, Ie: 3 A AC-13: Ue: 250 VAC, Ie: 5 A DC-13: Ue: 30 VDC, Ie: 0.5 A Transisor : DC-13: Ue: 30 VDC, Ie: 0.1 A 250 V 4 kv (a 240 VAC) 1000 A Relay oupu (SPDT) Relay oupu (SPDT) Time uni s (sec) 10 s (10 sec) min (min) 10 min (10 min) h (hrs) 10 h (10 hrs) Full scale o o o o o o 12 seing o 3 3 o o 3 3 o o 3 3 o o o o o o o o o o o o o 300 5

6 Raings H3CR-A Raed supply volage (See noes 1, 2, and 5.) 100 o 240 VAC (50/60 Hz)/100 o 125 VDC, 24 o 48 VAC (50/60 Hz)/12 o 48 VDC (24 o 48 VAC/VDC for H3CR-A8E) (See noe 3.) Operaing volage range rese 85% o 110% of raed supply volage (90% o 110% a 12 VDC) Minimum power-opening ime: 0.1 s Inpu (See noe 6.) No-volage Inpu ON impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 100 kω min. Volage Inpu Max. permissible capaciance beween inpus lines (erminals 6 and 7): 1,200 pf Load connecable in parallel wih inpus (erminals 6 and 7). 100 o 240 VAC/100 o 125 VDC High (logic) level: 85 o 264 VAC/85 o VDC Low (logic) level: 0 o 10 VAC/0 o 10 VDC 24 o 48 VAC/12 o 48 VDC High (logic) level: 20.4 o 52.8 VAC/10.8 o 52.8 VDC Low (logic) level: 0 o 2.4 VAC/0 o 1.2 VDC consumpion H3CR-A/-A8 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON: approx. 2.0 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W) 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) Relay ON: approx. 0.8 W Relay OFF: approx. 0.2 W H3CR-AP (See noe 3) 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON: approx. 2.5 VA (2.2 W) (See noe 4.) Relay OFF: approx. 1.8 VA (1.7 W) (See noe 4.) 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) Relay ON: approx. 0.9 W (See noe 4.) Relay OFF: approx. 0.3 W (See noe 4.) H3CR-A8E 100 o 240 VAC/100 o 125 VDC (When a 240 VAC, 60 Hz) Relay ON/OFF: approx. 2 VA (0.9 W) 24 o 48 VAC/VDC (When a 24 VDC) Relay ON/OFF: approx. 0.9 W H3CR-AS/-A8S 24 o 48 VAC/12 o 48 VDC (When a 24 VDC) ON: 0.3 W OFF: 0.2 W Conrol oupus Models wih Conac s H3CR-A/-A8/-AP 5A a 250 VAC/30 VDC, 0.15A a 125 VDC, resisive load (cosφ = 1) Minimum applied load: 10mA a 5 VDC (failure level: P reference value) Conac maerials: Ag-alloy H3CR-A8E 5A a 250 VAC/30 VDC, 0.15A a 125 VDC, resisive load (cosφ = 1) Minimum applied load: 10mA a 5 VDC (failure level: P reference value) Conac maerials: AgSnIn Transisor oupu: Open collecor(npn/pnp) H3CR-AS/-A8S 100 ma max a 30 VDC max., residual volage: 2 VDC max. Noe: 1. DC ripple rae: 20% max. (A single-phase, full-wave-recificaion power supply can be used). 2. Do no use an inverer oupu as he power supply. Refer o your OMRON websie for deails. 3. Models wih 24-o-48-VAC or 12-o-48-VDC power supply have inrush curren. Cauion is hus required when urning ON and OFF power o he Timer wih a non-conac oupu from a device such as a sensor. (Models wih an inrush curren of approximaely 50 ma and a 24- VDC power supply are available (he H3CR-A-302 and H3CR-A8-302).) For deails, consul your OMRON sales represenaive. 4. The values are for when he erminals 2 and 7 and erminals 10 and 6 are shor-ed, and include he consumpion curren of he inpu. 5. Refer o your OMRON websie when using he Timer ogeher wih a 2-wire AC proximiy sensor. 6. For deails, see Inpu Connecions: No-volage Inpu Signal Levels on page 11, and Inpu Connecions: Volage Inpu Signal Levels on page 12. 6

7 H3CR-A Characerisics Accuracy of operaing ±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s or 3 s) ime Seing error ±5% FS ±50 ms (See noe 1) Rese ime Min. power-opening ime: 0.1 s max. Min. pulse widh: 0.05 s (H3CR-A/-AS) Rese volage 10% max. of raed supply volage Influence of volage ±0.2% FS max. (±0.2%±10 ms max. in a range of 1.2 s or 3 s) (See noe 2) Influence of emperaure ±1% FS max. (±1%±10 ms max. in a range of 1.2 s or 3 s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed noncurren-carrying meal pars) 2,000 VAC (1,000 VAC for H3CR-A@S), 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) 2,000 VAC, 50/60 Hz for 1 min (beween inpu and conrol oupu erminals and operaion ) for H3CR-AP Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance 5 kv (beween power erminals) for 100 o 240 VAC/100 o 125 VDC, 1 kv for 24 o 48 VAC/12 o 48 VDC 5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 240 VAC/100 o 125 VDC, 1.5 kv for 24 o 48 VAC/12 o 48 VDC and 24 o 48 VAC/VDC ±1.5 kv (beween power erminals) and ±600 V (beween no-volage inpu erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude each in 3 direcions for 2 hours each Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude each in 3 direcions for 10 minues each Desrucion: 1,000 m/s 2 3 imes each in 6 direcions Malfuncion: 100 m/s 2 3 imes each in 6 direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy (See noe 4) Mechanical: 20,000,000 operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe 3) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC Immuniy RF-inerference: IEC Immuniy Burs: IEC Immuniy Surge: IEC Immuniy Conduced Disurbance: IEC Immuniy Volage Dip/Inerrupion: IEC Case color Ligh gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 90 g Noe: 1. The value is ±5% FS +100 ms o 0 ms max. when he C, D, or G mode signal of he H3CR-AP is OFF. 2. The influence of volage of he H3CR-A8E (24 o 48 VAC/12 o 48 VDC) is ±2.0% FS max. wih a single-phase power supply wih fullwave recificaion. 3. Refer o he Life-es Curve (Reference). 4. Conac oupu only. Life-es Curve (Reference) Swiching operaions (x 10 3 ) 10,000 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Load curren (A) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1A can be swiched a 125V DC and L/R = 7ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). 7

8 Connecions H3CR-A Block Diagrams H3CR-A/-AS/-A-301 AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Rese inpu, sar inpu, and gae inpu Inpu Indicaor -ON indicaor -ON indicaor H3CR-AP AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Sar Inpu Indicaor -ON indicaor -ON indicaor 8

9 H3CR-A H3CR-A8/-A8S/A8-301 AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Indicaor -ON indicaor -ON indicaor H3CR-A8E AC (DC) inpu Zero seing deecion Time range/ uni selecors Operaing mode selecor supply Oscillaion Couning Indicaor -ON indicaor -ON indicaor Insananeous oupu I/O Funcions Inpus (for -A/ Sar Sars ime-measuremen. -AS models) Rese Inerrups ime-measuremen and reses ime-measuremen value. Timing operaion is sopped and he conrol oupu urns OFF (i is rese). Gae The iming operaion is inerruped while he gae inpu is acive. s Conrol oupu s are urned ON according o designaed oupu mode when prese value is reached. Noe: H3CR-AP incorporaes sar inpu only. Models H3CR-A8/-A8E/-A8S/-A8-301 do no have an inpu funcion. 9

10 Terminal Arrangemen Noe: 1. The delayed conac of convenional Timers was indicaed as H3CR-A The conac symbol of he H3CR-A is indicaed as because is operaing mode is eigh muli-modes (five muli-modes for he H3CR-A8). 2. Do no use an empy erminal on he H3CR-AP/-AS/-A8S as a relay erminal or oherwise. 11-pin Models H3CR-A/-A-301 (Conac ) 8-pin Models H3CR-A8/-A8-301 (Conac ) Rese inpu Sar inpu Gae inpu supply supply H3CR-A8S (Transisor ) H3CR-AS (Transisor ) Rese inpu Sar inpu Gae inpu supply Noe: Terminals 1, 3, 4, and 5 are empy. Terminals 2 and 7 are he same as for he H3CR-A8. supply H3CR-A8E (Conac ) Noe: Terminals 1, 3, 4, and 8 are empy. Terminals 2, 5, 6, 7, and 10 are he same as for he H3CR-A. H3CR-AP (Conac ) Sar inpu supply supply Noe: 1. Terminal 5 is empy. 2. Separae power supplies can be used for he Timer and inpus. 10

11 H3CR-A Inpu Connecions H3CR-A/-AS/-A-301 The inpus of he H3CR-A/-AS/-A-301 are no-volage (shor- or open) inpus. No-volage Inpus No-conac Inpu Conac Inpu No-conac Inpu (Connecion o NPN open collecor oupu sensor.) 12 o 24 VDC (sensor power supply) + DC power supply (Connecion o a volage oupu sensor.) 12 o 24 VDC (sensor power supply) + DC power supply Sensor Timer 5 Gae 6 Sar 7 Rese Timer 5 Gae 6 Sar 7 Rese Sensor Timer Gae Sar Rese 2 Inpu (0 V) 2 Inpu (0 V) 2 Inpu (0 V) Operaes wih ransisor ON Operaes wih relay ON Operaes wih ransisor ON No-volage Inpu Signal Levels No-conac inpu Conac inpu 1. Shor- level Transisor ON Residual volage: 1 V max. Impedance when ON: 1 kω max. 2. Open level Transisor OFF Impedance when OFF: 100 kω min. Use conacs which can adequaely swich 0.1 ma a 5 V 11

12 H3CR-AP H3CR-A The sar inpu of he H3CR-AP is volage inpu. (Volage imposiion or open) Volage Inpus No-conac Inpu No-conac Inpu Conac Inpu (Connecion o PNP open (Connecion o NPN open collecor oupu sensor) collecor oupu sensor) 12 o 24 VDC (sensor power supply) Sensor + 10 supply (+) 6 Sar 7 2 DC power supply Timer Inpu 0V supply ( ) Sensor 12 o 24 VDC (sensor power supply) + DC power supply 10 supply (+) Timer Sar Inpu 0V supply ( ) AC power supply DC power supply 2 Timer 10 supply (+) 6 Sar 7 Inpu 0V supply ( ) Operaes wih PNP ransisor ON Operaes wih NPN ransisor ON Noe: The inpu is isolaed from he power supply. Thus, an NPN ransisor can be conneced. Operaes wih relay ON Noe: Refer o he signal levels in he following able and be aware of he minimum applicable load of he relay. Noe: Before making connecions, refer o Safey Precauions (H3CR-@). Volage Inpu Signal Levels No-conac inpu 1. Transisor ON Residual volage: 1 V max. The volage beween erminals 6 and 7 mus be 10.8 VDC min. 2. Transisor OFF Leakage curren: 0.01 ma max. The volage beween erminals 6 and 7 mus be 1.2 VDC max. Conac inpu Use conacs ha can adequaely swich 0.1 ma a each operaing volage. The volage beween erminals 6 and 7 wih conacs ON or OFF mus saisfy he specified value. Conacs ON 100-o-240-VAC and 100-o-125-VDC models: 85 o 264 VAC or 85 o VDC 24-o-48-VAC and 12-o-48-VDC models: 20.4 o 52.8 VAC or 10.8 o 52.8 VDC Conacs OFF 100-o-240-VAC and 100-o-125-VDC models: 0 o 10 VAC or 0 o 10 VDC 24-o-48-VAC and 12-o-48-VDC models: 0 o 2.4 VAC or 0 o 1.2 VDC 12

13 H3CR-A Operaion Timing Char (Refer o page 20 for applicaion examples.) H3CR-A/-AS/-AP*/-A-301 Operaing mode A: ON-delay Timing char Basic operaion Sar (See noe 4) Rese relay (NC) relay (NO) ( indicaor) (See Noe 7) indicaor Sar (See noe) Noe: Sar inpu is invalid while he Timer is in operaion. B: Flicker OFF sar Sar Basic operaion B2: Flicker ON sar (See noe 4) Rese relay (NC) relay (NO) ( indicaor) (See Noe 7) indicaor Sar Sar (See noe) Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion C: Signal ON/ OFF-delay (See noe 4) Rese relay (NC) relay (NO) ( indicaor) (See Noe 7) indicaor Sar Sar (See noe) Noe: Sar inpu is invalid while he Timer is in operaion. Basic operaion (See noe 4) Rese relay (NC) relay (NO) ( indicaor) (See Noe 7) indicaor Sar (See noe) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. Noe: 1. Allow a leas 0.1 s for he Timer rese ime if he power supply is rese due o an inerrupion in he power supply. 2. The minimum inpu pulse widh (for sar, rese) is 0.05 s. 3. The leer "" in he iming chars indicaes he se ime, and "-a" means ha he period is less han he se ime. ( - a < 1) 4. H3CR-AP model incorporaes sar inpu only. As such, he power supply is rese. 5. Model H3CR-AS only has operaion equivalen o ime-limi conac: NO. 6. When he seing dial is urned all he way pas 0 for insananeous oupu, "" (se ime) in he above ime char is 0-sec operaion. 7. During imer operaion, he flash frequency changes when 90% of he se ime has been reached. 13

14 H3CR-A Operaing mode D: Signal OFFdelay Sar Timing char Basic operaion (See noe 5) Rese relay (NC) relay (NO) ( indicaor) (See Noe 8) indicaor Sar (See noe) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. E: Inerval Sar Basic operaion (See noe 5) Rese Sar (See noe) relay (NC) relay (NO) ( indicaor) (See Noe 8) indicaor Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. (Previous sar inpu will be cancelled.) G: Signal ON/ OFF-delay Sar Basic operaion J: One-sho oupu (See noe 5) Rese relay (NC) relay (NO) ( indicaor) (See Noe 8) indicaor Sar Sar (See noe) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. Basic operaion (See noe 5) Rese relay (NC) relay (NO) ( indicaor) (See Noe 8) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Sar (See noe) 1±0.6 s (Fixed) Noe: Sar inpu is valid and reriggerable while he Timer is in operaion. (Previous sar inpu will be cancelled.) Gae Signal Inpu (This iming char indicaes he gae inpu in operaing mode A (ON-delay operaion).) Sar Gae Rese ON OFF ON OFF ON OFF ON OFF ON relay OFF 1 2 Noe: 1. Allow a leas 0.1 s for he Timer rese ime if he power supply is rese due o an inerrupion in he power supply. 2. The minimum inpu pulse widh (for sar, rese) is 0.05 s. 3. The leer "" in he iming chars indicaes he se ime, and "-a" means ha he period is less han he se ime. ( - a < 1) 4. In J Mode, here will be only one oupu even if he sar inpu is longer han he se ime. 5. H3CR-AP model incorporaes sar inpu only. As such, he power supply is rese. 6. Model H3CR-AS only has operaion equivalen o ime-limi conac: NO. 7. When he seing dial is urned all he way pas 0 for inananeous oupu, "" (se ime) in he above ime char is 0-sec operaion. 8. During imer operaion, he flash frequency changes when 90% of he se ime has been reached. Noe: The se ime is he sum of 1 and 2. Sar and rese are also boh enabled when he gae signal is ON. 14

15 H3CR-A H3CR-A8/-A8S/-A8-301 Operaing mode A: ON-delay Timing char Basic operaion relay (NC) relay (NO) ( indicaor) (See noe 6) indicaor B: Flicker OFF sar Basic operaion relay (NC) relay (NO) (oupu indicaor) (See noe 6) indicaor B2: Flicker ON sar Basic operaion E: Inerval relay (NC) relay (NO) (oupu indicaor) (See noe 6) indicaor v relay (NC) relay (NO) (oupu indicaor) (See noe 6) indicaor Basic operaion J: One-sho oupu relay (NC) relay (NO) (oupu indicaor) (See noe 6) indicaor 1±0.6 s (Fixed) 1±0.6 s (Fixed) Basic operaion 1±0.6 s (Fixed) Noe: 1. Allow a imer rese ime (R) of 0.1 s or longer. 2. The leer "" in he iming chars indicaes he se ime, and "-a" means ha he period is less han he se ime. ( - a < 1) 3. Model H3CR-A8S only has operaion equivalen o ime-limi conac: NO. 4. When he seing dial is urned all he way pas 0 for inananeous oupu, "" (se ime) in he above ime char is 0-sec operaion. 5. You can use J Mode o use he power supply as he sar inpu. 6. During imer operaion, he flash frequency changes when 90% of he se ime has been reached. 15

16 H3CR-A8E H3CR-A Operaing mode A: ON-delay relay (NC) Timing char relay (NO) (oupu indicaor) Basic operaion B: Flicker OFF sar Insananeous oupu relay (NC) Insananeous oupu relay (NO) (See Noe 6) indicaor B2: Flicker ON sar relay (NC) relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) (See Noe 6) indicaor Basic operaion relay (NC) relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Basic operaion Insananeous oupu relay (NO) (See Noe 6) indicaor E: Inerval relay (NC) J: One-sho oupu relay (NO) (oupu indicaor) Insananeous oupu relay (NC) Insananeous oupu relay (NO) (See Noe 6) indicaor Basic operaion relay (NC) relay (NO) (oupu indicaor) (Fixed) (Fixed) Basic operaion Insananeous oupu relay (NC) Insananeous oupu relay (NO) (See Noe 6) indicaor 1±0.6 s (Fixed) Noe: Refer o page

17 H3CR-A Nomenclaure indicaor (green) (Flashes when Timer operaes; li when Timer sops operaing) Operaing mode display window indicaor (orange) (Li when oupu) Operaing mode selecor Selec a mode from: A, B, B2, C, D, E, G, and J (H3CR-A, -AP, and -AS) A, B, B2, E and J (H3CR-A8, -A8S, and -A8E) Scale range display windows Time range selecor (selec one from 1.2, 3, 12, and 30 a full scale; wih he H3CR-A@-301, selec from 2.4, 6, 24, or 60 a full scale.) Time seing knob (se ime) Time uni display window Time uni selecor (selec one from sec, 10s, min, 10m, hrs, and 10h) Scale range display windows changes as below by urning he Time range selecor clockwise.* * On he H3CR-A@-301 ype, he ime is wice as long. 17

18 Dimensions H3CR-A Noe: All unis are in millimeers unless oherwise indicaed. H3CR-A H3CR-AP H3CR-AS H3CR-A dia pins H3CR-A8 H3CR-A8S H3CR-A8E H3CR-A dia Dimensions wih Se Ring Y92S-27/-28 (Order Separaely) pins dia. Time Seing Ring Panel cover Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ Dimensions wih Back Connecing Socke P3G-08/P3GA H3CR-A H3CR-A * H3CR-AS H3CR-AP 98.5 P2CF-11 P2CF-11-E 2.3* H3CR-A8@ 89.9* H3CR-A8-301 H3CR-A8E 87.6 H3CR-A8S P2CF-08 P2CF-08-E 2.3* H3CR-A H3CR-A-301 H3CR-AS H3CR-AP + Adaper Y92F-30 P3GA-11 (When Y92A-48G mouned) H3CR-A8@ H3CR-A8-301 H3CR-A8E H3CR-A8S + Adaper Y92F-30 P3G-08 (When Y92A-48G mouned) Noe: There are no resricions o he mouning direcion. * These dimensions vary wih he kind of DIN rack (reference value). 18

19 H3CR-A Accessories (Order Separaely) Proecive Cover Y92A-48B To use he Proecive Cover wih a flush mouning, use he Y92F-30 flush mouning adapor. This Proecive Cover canno be used ogeher wih he Y92F-73/-74 flush mouning adapor or he panel cover. Hold-down Clip Y92H-8 The Y92H-8 Hold-down Clip is aached o he PF085A socke. Y92H-7 Y92H-7 Hold-down Clip is aached wih screws ogeher wih he PL08 socke or he PL11 socke. 19

20 Applicaion Examples (H3CR-A) H3CR-A A Mode: ON-delay ON-delay operaion (A mode) is a basic mode. 1. -ON Sar/-OFF Rese The -ON sar/-off rese operaion is a sandard operaing mehod. (2 and 10) Sar (2 and 6) Rese (2 and 7) 3. Conrol of Inegraed Time wih Gae Signal Gae signal processing (during inpu or a emporary iming sop) is possible wih boh power sar and signal sar. (2 and 10) Sar (2 and 6) : se ime Conrol oupu: NC (8 and 11) NC (1 and 4) Gae (2 and 5) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) indicaor Exernally shor-ed Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Li Gae signal (The operaion is inerruped wih he gae signal if he Timer deecs an abnormal signal.) supply 2. Signal Sar/Signal Rese The Signal sar/signal rese operaion is useful for remoe conrol of he Timer. (2 and 10) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Sar signal (remoe conrol possible) Rese signal (remoe conrol possible) Li Exernally shor-ed B/B2 Mode: Flicker The flicker operaion in he B and B2 modes can be effecively applied o lamp or buzzer (ON and OFF) alarms or he monioring of an inermien operaion wih a display. 1. -ON Sar/-OFF Rese (in B Mode) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor supply Flashing Exernally shor-ed supply ( coninuously supplied) supply 20

21 H3CR-A 2. Signal Sar/Signal Rese (in B Mode) If here is an abnormal signal, flashing sars. When he abnormal condiion is resored, a rese signal sops he display flashing. (2 and 10) Sar (2 and 6) Rese (2 and 7) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Sar signal Rese signal 2. Signal-ON-OFF Sar/Insananeous Operaion/Time-limi Rese (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li Flashing Li Flashing Li Sar signal (The operaion sars wih he signal ON or OFF) supply ( coninuously supplied) C Mode: Signal ON/OFF-delay The Signal ON-/OFF-delay operaion (C mode) is useful for he conrol of disribuion of producs on a producion line ino boxes by he specified number or ime. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese A se of hese funcions is useful for he operaion of a machine for a specified period when power is ON. D Mode: Signal OFF-delay Signal OFF-delay operaion (D mode) can be effecively used o keep a load operaing for a cerain period. For example, his funcion enables he cooling fan for a lamp or heaer o operae for a cerain period afer he lamp or heaer is swiched OFF. 1. -ON Sar/Insananeous Operaion/ Time-limi Rese (2 and 10) supply ( coninuously supplied) Sar (2 and 6) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Li Flashing Li indicaor Flashing Li Flashing Li Sar signal (NC o NO) Exernally shor-ed supply supply 21

22 H3CR-A 2. Signal Sar/Insananeous Operaion/ Time-limi Rese (2 and 10) 2. Signal Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he repeiive conrol such as he filling of liquid for a specified period afer each Signal sar inpu. Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Li Flashing Li Conrol oupu: NO (9 and 11) NO (1 and 3) Sar signal (NO o NC o NO) indicaor Sar signal Flashing Li Flashing Li E Mode: Inerval supply ( coninuously supplied) 1. -ON Sar/Insananeous Operaion/ Time-limi Rese This funcion is useful for he operaion of a machine for a specified period afer power is ON. supply ( coninuously supplied) (2 and 10) Sar (2 and 6) Conrol oupu: NC (8 and 11) NC (1 and 4) Conrol oupu: NO (9 and 11) NO (1 and 3) indicaor Flashing Li Flashing Li Exernally shor-ed supply 22

23 H3CR-A Safey Precauions (H3CR-A) Refer o Safey Precauions for All Timers. Noe: The following precauions apply o all H3CR-A models. Supplies For he power supply of an inpu device of he H3CR-A use an isolaing ransformer wih he primary and secondary windings muually isolaed and he secondary winding no grounded. Correc G, S, R 5, 6, 7 2 H3CR-A Inpu erminal 10 2 supply Inpu/ Relaionship beween Inpu and Supply Circuis (excep for H3CR-A8E) The H3CR-A (excep for H3CR-A8E) uses ransformerless power supply. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shoring due o a sneak curren o he ransformerless power supply. If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no differ in phase, oherwise he erminals will be shor-ed o one anoher. Incorrec Conac or ransisor for exernal inpu signal H3CR-A Shor- curren Inpu device Isolaion ransformer is required. Inpu erminal supply Incorrec G, S, R 5, 6, 7 2 H3CR-A Inpu erminal 10 2 supply Inpu erminal Correc Conac or ransisor for exernal inpu signal H3CR-A Inpu device Isolaion ransformer Inpu erminal supply The H3CR-A s power supply erminal 2 is a common erminal for inpu signals o he Timer. Do no disconnec he wires on erminal 2, oherwise he inernal ry of he Timer will be damaged. Inpu erminal AC or DC Supply 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A I is impossible o provide wo independen power swiches as shown below regardless of wheher or no he Timers are differen in phase. 2 Conac or ransisor for exernal inpu signal H3CR-A Inpu erminal supply Inpu erminal 23

24 Relaionship beween Inpu and Supply Circuis An appropriae inpu is applied o he inpu signal erminals of he H3CR-A@/-A@S when one of he inpu erminals is shor-ed wih he common erminal (erminal 2) for he inpu signals. Never use erminal 10 as he common erminal for his purpose, oherwise he inernal of he Timer will be damaged. Correc Incorrec AC or DC power supply 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A/-AS 2 H3CR-A If a relay or ransisor is conneced o wo or more Timers, he inpu erminals of hose Timers mus be wired properly so ha hey will no be differen in phase or he erminals will be shor-ed o one anoher (refer o he figures below). Incorrec Conac or ransisor for exernal inpu signal H3CR-AP 2 10 H3CR-AP 2 supply Shor- curren 10 Correc Conac or ransisor for exernal inpu signal AC or DC power supply 5, 6, 7 G, S, R Inpu erminal H3CR-A/-AS 2 * H3CR-AP supply 2 AC or DC power supply Inpu conac Ry *2 5, 6, 7 G, S, R Inpu erminal 10 H3CR-A/-AS H3CR-AP 2 Shor- curren *1 erminal 2 is a common erminal ha is also used for he inpu signal. Do no use erminal 10 as a common erminal as his will damage he inernal ry. *2 If a relay or oher load is conneced here, high volage will be applied o he inpu erminal and damage he inernal ry. The ransisor oupu of he H3CR-A@S is isolaed from he inernal ry by a phoocoupler, and can herefore be used eiher as an NPN oupu ype or a PNP (equivalen) oupu ype. Relaionship beween Inpu and Supply Circuis (H3CR-AP) H3CR-AP When using he imer in an environmen where considerable noise occurs, keep he inpu signal source device, imer uni, and wiring as far away as possible from he source of he noise. I is also recommended ha shielded wire be used for he inpu signal wiring as a counermeasure for noise. Common o All H3CR-A Models Wih he H3CR-AP, inpu wires mus be as shor as possible. If he floaing capaciy of wires exceeds 1,200 pf (approx. 10 m for cables wih 120 pf/m), he operaion will be affeced. Pay paricular aenion when using shielded cables. The H3CR-A@S ransisor oupu is isolaed from he inernal ry by a phoocoupler. Therefore, eiher NPN or PNP oupu is possible. AC/DC power supply Inpu supply Since he inpu and he power supply are configured independenly, he inpu can be urned ON or OFF irrespecive of he ON/OFF sae of he power supply. I mus be noed ha a volage equivalen o he power supply volage is applied o he inpu. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by To conver grams ino ounces, muliply by In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 24

25 25 MEMO

26 Solid-sae Twin Timers H3CR-F DIN mm Twin Timers Wide power supply ranges of High Volage 100 o 240 VAC/100 o 125 VDC and Low Volage 24 o 48 VAC/12 o 48 VDC. ON- and OFF-imes can be se independenly and so combinaions of long ON- or OFF-ime and shor OFF- or ONime seings are possible. Tweny-four ime ranges from 0.05 s o 300 h depending on he model o be used. Models wih a flicker ON sar or flicker OFF sar are available. Easy sequence checks hrough insananeous oupus for a zero se value a any ime range. Lengh, when panel-mouned wih a Socke, of 80 mm or less. 11-pin and 8-pin models are available. Model Number Srucure For he mos recen informaion on models ha have been cerified for safey sandards, refer o your OMRON websie. Model Number Legend H3CR @ Classificaion F: Twin imers 2. Configuraion None: 11-pin socke 8: 8-pin socke 3. Twin Timer Mode None: Flicker OFF sar N: Flicker ON sar 4. Time Range None: 0.05 s o 300 h models 5. Supply Volage AC/ DC: 100 o 240 VAC/100 o 125 VDC 24-48AC/12-48DC: 24 o 48 VAC/12 o 48 VDC Noe: When your order, specify he power supply volage. Ordering Informaion Lis of Models Operaing modes Supply volage 0.05 s o 300 h models 11-pin models 8-pin models Flicker OFF sar 100 o 240 VAC/100 o 125 VDC H3CR-F AC/ DC H3CR-F AC/ DC 24 o 48 VAC/12 o 48 VDC H3CR-F 24-48AC/12-48DC H3CR-F AC/12-48DC Flicker ON sar 100 o 240 VAC/100 o 125 VDC H3CR-FN AC/ DC H3CR-F8N AC/ DC 24 o 48 VAC/12 o 48 VDC H3CR-FN 24-48AC/12-48DC H3CR-F8N 24-48AC/12-48DC Noe: Specify boh he model number and supply volage when ordering. Example: H3CR-F AC/ DC Supply volage 26

27 H3CR-F Accessories (Order Separaely) Adaper, Proecive Cover and Hold-down Clip Name/specificaions Flush Mouning Adaper Y92F-30 Y92F-73 *1 Y92F-74 *1 Proecive Cover Y92A-48B *2 Hold-down Clip For PF085A Socke Y92H-8 (Sold in ses of wo) For PL08 or PL11 Sockes Y92H-7 Models Noe: Refer o Operaion (Common) daashee for deails. *1 The Y92A-48B Proecive Cover and he Y92F-73/-74 Flush Mouning Adaper canno be used a he same ime. *2 The Y92A-48B Proecive Cover is made from hard plasic. Remove he Proecive Cover o change he se value. The Y92A-48B Proecive Cover and he Y92F-73/-74 Flush Mouning Adaper also canno be used a he same ime. Sockes Timer Round Sockes Pin Connecion Terminal Models 11-pin Fron Connecing DIN rack mouning P2CF-11 DIN rack mouning P2CF-11-E (Finger-safe ype) Back Connecing Screw erminal P3GA-11 Solder erminal PL11 Wrapping erminal PL11-Q PCB erminal PLE pin Fron Connecing DIN rack mouning P2CF-08 DIN rack mouning P2CF-08-E (Finger-safe ype) DIN rack mouning PF085A Back Connecing Screw erminal P3G-08 Solder erminal PL08 Wrapping erminal PL08-Q PCB erminal PLE08-0 Noe: 1. The P2CF-@@-E has a finger-proecion srucure. Round crimp erminals canno be used. Use forked crimp erminals. 2. The P3GA-11 and P3G-08 Socke can be used ogeher wih he Y92A-48G Terminal Cover o implemen finger proecion. 3. For deails, refer o your OMRON websie. Terminal Cover Applicaion Model Remarks For back connecing socke Y92A-48G For P3G-08 and P3GA-11 Noe: For deails, refer o your OMRON websie. 27

28 Specificaions H3CR-F General Iem H3CR-F H3CR-F8 H3CR-FN H3CR-F8N Operaing mode Flicker OFF sar Flicker ON sar Pin ype 11-pin 8-pin 11-pin 8-pin Operaing/Rese mehod ype Mouning mehod Noe: For deails, refer o your OMRON websie. * CCC cerificaion requiremens Time-limi operaion/time-limi rese or self-rese Relay oupu (DPDT) DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds, CCC: GB/T * Conforms o EN and IEC (VDE0110) 4kV/2. caegory according o EN Recommended fuse Raed operaing volage Ue Raed operaing curren Ie Raed insulaion volage Raed impulse wihsand volage (aliude: 2,000 m max.) Condiional shor- curren (250VAC, 5A), manufacured by Lielfuse AC-15: Ue: 250 VAC, Ie: 3 A AC-13: Ue: 250 VAC, Ie: 5 A DC-13: Ue: 30 VDC, Ie: 1.5 A 250 V 4 kv (a 240 VAC) 1000 A Time Ranges Time uni s (sec) 10 s (10 sec) min (min) 10 min (10 min) h (hrs) 10 h (10 hrs) Fullscale o o o o o o 12 seing o 3 3 o o 3 3 o o 3 3 o o o o o o o o o o o o o 300 Noe: The imes ha can be se are given. When he ime seing knob is urned below 0 unil he poin where he ime seing knob sops, he oupu will operae insananeously a all ime range seings. For deails, refer o your OMRON websie. Raings Raed supply volage (See noes 1, 2, and 3.) 100 o 240 VAC 50/60 Hz/100 o 125 VDC 24 o 48 VAC 50/60 Hz/12 o 48 VDC Operaing volage range 85% o 110% of raed supply volage; 90% o 110% wih 12-VDC models rese Minimum power-opening ime: 0.1 s consumpion 100 o 240 VAC: approx. 10 VA (2.1 W) a 240 VAC 24 VAC/VDC: approx. 2 VA (1.7 W) a 24 VAC approx. 1 W a 24 VDC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) The minimum applicable load is 10mA a 5VDC (P reference value). Conac maerials : Ag-alloy Noe: 1. A power supply wih a ripple of 20% max. (single-phase power supply wih full-wave recificaion) can be used wih each DC Model. 2. Do no use an inverer oupu as he power supply. Refer o your OMRON websie for deails. 3. Refer o your OMRON websie when using he Timer ogeher wih a 2-wire AC proximiy sensor. 28

29 H3CR-F Characerisics Accuracy of operaing ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s) ime Seing error ±5% FS ±50 ms max. Rese ime 0.1 s max. Rese volage 10% max. of raed volage Influence of volage ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 1.2 and 3 s) Influence of emperaure ±1% FS max. (±1% FS ±10 ms max. in ranges of 1.2 and 3s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance Noe: Refer o he Life-es Curve (Reference). 5kV (beween power erminals), however, 1kV for 24 o 48VAC, 12 o 48 VDC 5kV (beween curren-carrying erminal and exposed non-curren-carrying meal pars), however 1.5 kv for 24 o 48 VAC, 12 o 48 VDC ±1.5 kv (beween power erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 98 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 20 million operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC Immuniy RF-inerference: IEC Immuniy Burs: IEC Immuniy Surge: IEC Immuniy Conduced Disurbance: IEC Immuniy Volage Dip/Inerrupion: IEC Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 100 g Life-es Curve (Reference) 10,000 Swiching operaions (x 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1A can be swiched a 125V DC and L/R = 7ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). Load curren (A) 29

30 Connecions H3CR-F Block Diagrams H3CR-F/-F8/-FN/F8N ON indicaor OFF indicaor Zero seing deecion Indicaor ROM RAM Clock AC (DC) inpu supply One-chip microcompuer Time range/uni selecors I/O Funcions Inpus --- s Conrol oupu s are urned ON/OFF according o he ime se by he ON- and OFF-ime seing knob. Terminal Arrangemen H3CR-F8/-F8N H3CR-F/-FN (+)(~) supply supply Noe: Leave erminals 5, 6, and 7 open. Do no use hem as relay erminals. 30

31 H3CR-F Operaion Timing Char ON: ON se ime OFF: OFF se ime Operaing mode Flicker OFF sar Timing char R ON indicaor ON OFF Li No li OFF ON OFF ON OFF OFF OFF indicaor Li No li Flicker ON sar NO NC ON indicaor OFF indicaor NO NC ON OFF ON OFF ON OFF Li No li Li No li ON OFF ON OFF ON OFF ON OFF ON OFF R Noe: 1. Allow a imer rese ime (R) of 0.1 s or longer 2. When he seing dial is urned all he way pas 0 for inananeous oupu, "" (se ime) in he above ime char is 0-sec operaion. Nomenclaure Scale range display windows changes as below by urning he Time range selecor clockwise OFF indicaor (green) Li when he oupu is OFF. ON indicaor (orange) Li when he oupu is ON. OFF-ime uni display window OFF-ime uni selecor (selec one from sec. 10 s, min., 10 min, hrs, and 10 h) Scale range display windows Time range selecor (selec one from 1.2, 3, 12, and 30 a full scale) For boh ON-ime and OFF-ime. ON-ime seing knob (wih orange poiner) For ON-ime seing OFF-ime seing knob (wih green poiner) For OFF-ime seing ON-ime uni display window ON-ime uni selecor (selec one from sec, 10 s, min, 10 min, hrs, and 10 h) 31

32 Dimensions H3CR-F Noe: All unis are in millimeers unless oherwise indicaed. H3CR-F H3CR-FN din. 14 din pins H3CR-F8 H3CR-F8N din. 14 din pins Dimensions wih Flush Mouning Adaper Y92F-30 Flush Mouning Adaper (Order Separaely) Panel P3G Back Connecing Socke (Order separaely) Mouning Hole Dimensions (Conform o DIN ) 0.5 R max (N) Noe: 1. The orienaion of he Adapers for wo or more Timers is differen for a horizonal or verical layou. Make sure he orienaion is correc. Consecuive Mouning of n Timers Wihou Fron Covers: N = (48n - 2.5) Wih Fron Covers: N = (51n - 5.5) Wih Panel Covers: N = (50n - 4.5) The applicable hickness of he mouning panel mus be 1 o 5 mm. Y92F-73 Flush Mouning Adaper (Order Separaely) Panel P3G Adaper mouning holes: Two, 4.5 d Back Connecing Socke 0.5 R max. 52 o ± o 66 76±0.2 Inser he Timer in his direcion.* 45± Noe: A Fron Cover and Flush Mouning Adaper canno be used a he same ime Noe: The applicable hickness of he mouning panel mus be 1 o 3.2 mm. * Inser he Timer from he back of he Adaper. 32

33 H3CR-F Y92F-74 Flush Mouning Adaper (Order Separaely) 56 Panel P3G Back Connecing Socke 0.5 R max ± ± Noe: A Fron Cover and Flush Mouning Adaper canno be used a he same ime Noe: The applicable hickness of he mouning panel mus be 1 o 3.2 mm. Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ Dimensions wih Back Connecing Socke P3G-08/P3GA-11 H3CR-F H3CR-FN 103.2* H3CR-F8 H3CR-F8N 92.3* H3CR-F H3CR-FN + Adaper H3CR-F8 H3CR-F8N + Adaper Y92F-30 P3GA-11 Y92F-30 P3G-08 (When (When P2CF * P2CF * Y92A-48G Y92A-48G P2CF-11-E P2CF-08-E mouned) mouned) * These dimensions vary wih he kind of DIN rack (reference value). Noe: There are no resricions o he mouning direcion. Accessories (Order Separaely) Proecive Cover Y92A-48B To use he Proecive Cover wih a flush mouning, use he Y92F-30 flush mouning adapor. This Proecive Cover canno be used ogeher wih he Y92F-73/-74 flush mouning adapor or he panel cover. Hold-down Clip Y92H-8 The Y92H-8 Hold-down Clip is aached o he PF085A socke. Hold-down Clip Y92H-7 Y92H-7 Hold-down Clip is aached wih screws ogeher wih he PL08 socke or he PL11 socke. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by To conver grams ino ounces, muliply by In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 33

34 Solid-sae Sar-dela Timers H3CR-G DIN mm Sar-dela Timer A wide sar-ime range (up o 120 seconds) and sar-dela ransfer ime range (up o 1 seconds). For he mos recen informaion on models ha have been cerified for safey sandards, refer o your OMRON websie. Model Number Srucure Model Number Legend H3CR - G Classificaion G: Sar-dela imer 2. Configuraion 8: 8-pin socke Noe: When your order, specify he power supply volage. 3. s None: Sar-dela operaion conac E: Sar-dela operaion conac and insananeous conac 4. Dimensions L: Long-body model 5. Supply Volage AC: 100 o 120 VAC AC: 200 o 240 VAC Ordering Informaion Lis of Models s Supply volage 8-pin models Time-limi conac 100 o 120 VAC H3CR-G8L AC 200 o 240 VAC H3CR-G8L AC Time-limi conac and insananeous conac 100 o 120 VAC H3CR-G8EL AC Noe: Specify boh he model number and supply volage when ordering. Example: H3CR-G8L AC Supply volage 200 o 240 VAC H3CR-G8EL AC 34

35 H3CR-G Accessories (Order Separaely) Accessories (Order Separaely) Adaper, Proecive Cover, Seing Ring and Panel Cover Name/specificaions Flush Mouning Adaper Y92F-30 Y92F-70 *1 Y92F-71 *1 Proecive Cover Y92A-48B *2 Hold-down Clip For PF085A Socke Y92H-2 For PL08 Sockes Y92H-1 Seing Ring A Y92S-27 *3 Seing Ring B and C Y92S-28 *3 Panel Cover Ligh gray (5Y7/1) Y92P-48GL *4 Black (N1.5) Y92P-48GB *4 Models Noe: Refer o Operaion (Common) daashee for deail. *1 The Y92A-48B Proecive Cover and he Y92P-48G@ Panel Cover can no be used a he same ime wih he Y92F-70/-71 Flush Mouning Adaper. *2 The Y92A-48B Proecive Cover is made from hard plasic. Remove he Proecive Cover o change o se value. The Y92F-70/-71 Flush Mouning Adaper and he Y92P-48G@ Panel Cover canno be used a he same ime wih Y92A-48B Proecive Cover. *3 The Y92S-27/-28 Seing Ring canno be used alone. I mus be used ogeher wih he Y92P-48G@ Panel Cover. *4 The Y92A-48B Proecive Cover and he Y92F-70/-71 Flush Mouning Adaper canno be used a he same ime wih he Y92P-48G@ Panel Cover. Sockes Timer Round Sockes Pin Connecion Terminal Models 8-pin Fron Connecing DIN rack mouning P2CF-08 DIN rack mouning P2CF-08-E (Finger-safe ype) DIN rack mouning PF085A Back Connecing Screw erminal P3G-08 Solder erminal PL08 Wrapping erminal PL08-Q PCB erminal PLE08-0 Noe: 1. The P2CF-08-E has a finger-proecion srucure. Round crimp erminals canno be used. Use forked crimp erminals. 2. The P3G-08 Socke can be used ogeher wih he Y92A-48G Terminal Cover o implemen finger proecion. 3. For deails, refer o your OMRON websie. Terminal Cover Applicaion Model Remarks For back connecing socke Y92A-48G For P3G-08 and P3GA-11 Noe: For deails, refer o your OMRON websie. 35

36 Specificaions H3CR-G General Iem H3CR-G8L H3CR-G8EL Funcions Sar-dela imer Sar-dela imer wih insananeous oupu Pin ype Operaing/Rese mehod ype Mouning mehod Noe: For deails, refer o your OMRON websie. * CCC cerificaion requiremens 8-pin Time-limi operaion/self-rese Time-limi: SPST-NO (sar operaion ) SPST-NO (dela operaion ) DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds, CCC: GB/T * Conforms o EN and IEC (VDE0110) 4kV/2. caegory according o EN Time-limi: SPST-NO (sar operaion ) SPST-NO (dela operaion ) Insananeous: SPST-NO Recommended fuse Raed operaing volage Ue Raed operaing curren Ie Raed insulaion volage Raed impulse wihsand volage (aliude: 2,000 m max.) Condiional shor- curren (250VAC, 5A) manufacured by Lielfuse AC-15: Ue: 250 VAC, Ie: 5 A DC-13: Ue: 30 VDC, Ie: 1.5 A 250 V 4 kv (a 240 VAC) 1000 A Time Ranges Time uni Scale number (max.) 6 Se ime range 0.5 o 6 s 12 1 o 12 s 60 5 o 60 s o 120 s Sar operaion ime ranges Sar-dela ransfer ime Raings Programmable a 0.05 s, 0.1 s, 0.25 s, 0.5 s, 0.75 s, or 1.0 s Raed supply volage (See noes 1 and 2.) 100 o 120 VAC (50/60 Hz), 200 o 240 VAC (50/60 Hz) Operaing volage range 85% o 110% of raed supply volage rese Minimum power-opening ime: 0.5 s consumpion 100 o 120 VAC: approx. 6 VA (2.6 W) a 120 VAC 200 o 240 VAC: approx. 12 VA (3.0 W) a 240 VAC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) The minimum applicable load is 10mA a 5VDC (P reference value). Conac maerials : Ag-alloy Noe: 1. Do no use an inverer oupu as he power supply. Refer o your OMRON websie for deails. 2. Refer o your OMRON websie when using he Timer ogeher wih a 2-wire AC proximiy sensor. 36

37 H3CR-G Characerisics Accuracy of operaing ime Seing error Accuracy of Sar-dela ransfer ime Rese volage Influence of volage Influence of emperaure Insulaion resisance Dielecric srengh Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance ±0.2% FS max. ±5% FS ±50 ms max. ±25% FS + 5 ms max. Noe: Refer o he Life-es Curve (Reference). 10% max. of raed volage ±0.2% FS max. ±1% FS max. 100 MΩ min. (a 500 VDC) 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) 5 kv (beween power erminals) 5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) ±1.5 kv (beween power erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise) Malfuncion: 8 kv Desrucion: 15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 294 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 20 million operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,800 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC Immuniy RF-inerference: IEC Immuniy Burs: IEC Immuniy Surge: IEC Immuniy Conduced Disurbance: IEC Immuniy Volage Dip/Inerrupion: IEC Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh H3CR-G8L: approx. 110 g; H3CR-G8EL: approx. 130 g 37

38 Life-es Curve (Reference) H3CR-G 10,000 Swiching operaions ( 10 3 ) 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1A can be swiched a 125V DC and L/R = 7ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). Load curren (A) Connecions Block Diagrams H3CR-G8L Sar operaion ime range selecor Sar-dela ransfer ime selecor AC inpu supply Sar operaion ime oscillaion Sar operaion ime couning Sar-dela ransfer ime oscillaion Sar-dela ransfer ime couning Sar operaion Dela operaion Indicaor Sar operaion indicaor Dela operaion indicaor H3CR-G8EL Sar operaion ime range selecor Sar-dela ransfer ime selecor AC inpu supply Sar operaion ime oscillaion Sar operaion ime couning Sar-dela ransfer ime oscillaion Sar-dela ransfer ime couning Sar operaion Dela operaion Indicaor Sar operaion indicaor Dela operaion indicaor Insananeous oupu 38

39 H3CR-G I/O Funcions Inpus --- s Conrol oupu If he ime reaches he value se wih he ime seing knob, he sar operaion oupu will be urned OFF and here will be dela operaion oupu afer he se sar-dela ransfer ime has elapsed. Terminal Arrangemen H3CR-G8L H3CR-G8EL Dela operaion conac Sar operaion conac Insananeous conac Dela operaion conac Sar operaion conac Noe: Leave erminals 1, 3, and 4 open. Do no use hem as relay erminals. Operaion Noe: Leave erminal 4 open. Do no use hem as relay erminals. Timing Char 1: Sar operaion ime seing 2: Sar-dela ransfer ime Model H3CR-G8L/-G8EL Timing char 0.5 s min. (2 7) ON OFF Insananeous oupu (1 3) (-E models) ON OFF 1 Sar operaion oupu (8 5) ON OFF 2 Dela operaion oupu (8 6) ON OFF Sar operaion indicaor Li No li Dela operaion indicaor Li No li Nomenclaure Scale range display windows changes as below by urning he Time range selecor clockwise Sar operaion indicaor (green) Dela operaion indicaor (orange) Scale range display windows Time uni display (sec is fixed) Time seing knob (for seing sar operaion ime) Sar operaion ime range selecor (selec one from 6, 12, 60, and 120 a full scale) Sar-dela ransfer ime selecor (selec one from 0.05 s, 0.1 s, 0.25 s, 0.5 s, 0.75 s, and 1.0 s) Sar-dela ransfer ime display window 39

40 Dimensions H3CR-G Noe: All unis are in millimeers unless oherwise indicaed. Dimension of Timer main uni 15 (78) dia Dimensions wih Se Ring and Panel Cover Y92S-27/-28 (Order Separaely) dia. Dimensions wih Fron Connecing Socke P2CF-08-@ Time seing ring Panel cover Dimensions wih Back Connecing Socke P3G H3CR-G8@L 101.3* 99 P2CF-08 P2CF-08-E Noe: There are no resricions o he mouning direcion. * These dimensions vary wih he kind of DIN rack (reference value). 2.3* H3CR-G8@L + Adaper Y92F-30 P3G-08 (When Y92A-48G mouned) 40

41 H3CR-G Accessories (Order Separaely) Proecive Cover Y92A-48B To use he Proecive cover wih a flush mouning, use he Y92F-30 flush mouning adapor. This Proecive cover canno be used ogeher wih he Y92F-70/-71 flush mouning adapor or he panel cover. Hold-down Clip Y92H-2 The Y92H-2 Hold-down Clip is aached o he PF085A socke. Y92H-1 Y92H-1 Hold-down Clip is aached wih screws ogeher wih he PL08 socke. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by To conver grams ino ounces, muliply by In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 41

42 Solid-sae OFF-delay Timers H3CR-H DIN mm OFF-delay Timer Long power OFF-delay imes; S-series: up o 12 seconds, M-series: up o 12 minues. Models wih forced-rese inpu are available. 11-pin and 8-pin models are available. For he mos recen informaion on models ha have been cerified for safey sandards, refer o your OMRON websie. Model Number Srucure Model Number Legend Noe: This model number legend includes combinaions ha are no available. Before ordering, please check he Lis of Models on page 42 for availabiliy. H3CR @ Classificaion H: OFF-delay imer 2. Configuraion None: 11-pin socke 8: 8-pin socke Lis of Models Noe: Specify he model number, supply volage, and ime range (S or M) when ordering. 3. Inpu None: Wihou rese inpu R: Wih rese inpu 4. Dimensions L: Long-body model 5. Supply Volage 6. Time Range AC: 100 o 120 VAC S: 0.05 o 12 s AC: 200 o 240 VAC M: 0.05 o 12 min 24AC/DC: 24VAC/DC 48DC: 48 VDC DC: 100 o 125 VDC Inpu Supply volage S-series M-series 11-pin models 8-pin models 11-pin models 8-pin models Wihou DPDT 100 o 120 VAC --- H3CR-H8L AC S --- H3CR-H8L AC M rese 200 o 240 VAC H3CR-H8L AC S H3CR-H8L AC M inpu 24 VAC/DC H3CR-H8L 24AC/DC S H3CR-H8L 24AC/DC M 48 VDC H3CR-H8L 48DC S H3CR-H8L 48DC M 100 o 125 VDC H3CR-H8L DC S H3CR-H8L DC M Wih 100 o 120 VAC H3CR-HRL AC S --- H3CR-HRL AC M --- rese 200 o 240 VAC H3CR-HRL AC S H3CR-HRL AC M inpu 24 VAC/DC H3CR-HRL 24AC/DC S H3CR-HRL 24AC/DC M 48 VDC H3CR-HRL 48DC S H3CR-HRL 48DC M 100 o 125 VDC H3CR-HRL DC S H3CR-HRL DC M SPDT 100 o 120 VAC --- H3CR-H8RL AC S --- H3CR-H8RL AC M 200 o 240 VAC H3CR-H8RL AC S H3CR-H8RL AC M 24 VAC/DC H3CR-H8RL 24AC/DC S H3CR-H8RL 24AC/DC M 48 VDC H3CR-H8RL 48DC S H3CR-H8RL 48DC M 100 o 125 VDC H3CR-H8RL DC S H3CR-H8RL DC M Noe: Specify he model number, supply volage, and ime range (S or M) when ordering. Example: H3CR-H8L AC S Time range Supply volage 42

43 H3CR-H Accessories (Order Separaely) Adaper, Proecive Cover and Hold-down Clip Name/specificaions Models Flush Mouning Adapers Y92F-30 Noe: Refer o Operaion Y92F-70 *1 Y92F-71 *1 Proecive Cover Y92A-48B *2 Hold-down Clips For PF085A Socke Y92H-2 For PL08 or PL11 Sockes Y92H-1 Sockes Noe: 1. The P2CF-@@-E has a finger-proecion srucure. Round crimp erminals canno be used. Use forked crimp erminals. 2. The P3GA-11 and P3G-08 Socke can be used ogeher wih he Y92A-48G Terminal Cover o implemen finger proecion. 3. For deails, refer o your OMRON websie. Terminal Cover Noe: For deails, refer o your OMRON websie. (Common) daashee for deails. *1.The Y92A-48B Proecive Cover and he Y92F-70/-71 Flush Mouning Adaper canno be used a he same ime. *2.The Y92F-48B Proecive Cover is made from hard plasic. Remove he Proecive Cover o change he se value. Timer Round Sockes Pin Connecion Terminal Models 11-pin Fron Connecing DIN rack mouning P2CF-11 DIN rack mouning P2CF-11-E (Finger-safe ype) Back Connecing Screw erminal P3GA-11 Solder erminal PL11 Wrapping erminal PL11-Q PCB erminal PLE pin Fron Connecing DIN rack mouning P2CF-08 DIN rack mouning P2CF-08-E (Finger-safe ype) DIN rack mouning PF085A Back Connecing Screw erminal P3G-08 Solder erminal PL08 Wrapping erminal PL08-Q PCB erminal PLE08-0 Applicaion Model Remarks For back connecing socke Y92A-48G For P3G-08 and P3GA-11 43

44 Specificaions H3CR-H General Noe: For deails, refer o your OMRON websie. * CCC cerificaion requiremens Time Ranges Noe: 1. If he above minimum power ON ime is no secured, he H3CR may no operae. Be sure o secure he above minimum power ON ime. 2. Do no use he Timer wih a repea period of less han 3 s. Doing so may resul in abnormal heaing or burning. Refer o Safey Precauions (H3CR-H) on page 50 for deails. Raings Iem H3CR-H8L H3CR-H8RL H3CR-HRL Operaing/Rese mehod Insananeous operaion/time-limi rese Insananeous operaion/time-limi rese/forced rese Pin ype 8-pin 11-pin Inpu ype --- No-volage inpu ype Relay oupu (DPDT) Relay oupu (SPDT) Relay oupu (DPDT) Mouning mehod DIN rack mouning, surface mouning, and flush mouning Approved sandards UL508, CSA C22.2 No.14, NK, Lloyds, CCC: GB/T * Conforms o EN and IEC (VDE0110) 4kV/2. caegory according o EN Recommended fuse Raed operaing volage Ue Raed operaing curren Ie Raed insulaion volage Raed impulse wihsand volage (aliude: 2,000 m max.) Condiional shor- curren (250VAC, 5A), manufacured by Lielfuse AC-15: Ue: 250 VAC, Ie: 3 A AC-13: Ue: 250 VAC, Ie: 5 A DC-13: Ue: 30 VDC, Ie: 0.5 A 250 V 4 kv (a 240 VAC) 1000 A Time uni S-series M-series Scale number (max.) s (sec) min (min) 0.6 Se ime range 0.05 o o o o 12 Min. power ON ime 0.1 s min. 2 s min. Time-up operaion repea period 3 s min. Forced-rese repea period 3 s min. Raed supply volage (See noes 1 and 2.) 100 o 120 VAC (50/60 Hz), 200 o 240 VAC (50/60 Hz), 24 VAC/VDC (50/60 Hz), 48 VDC, 100 o 125 VDC Operaing volage range 85% o 110% of raed supply volage No-volage inpu (See noe 3.) ON-impedance: 1 kω max. ON residual volage: 1 V max. OFF impedance: 500 kω min. consumpion 100 o 120 VAC: approx VA (0.22 W) a 120 VAC 200 o 240 VAC: approx VA (0.3 W) a 240 VAC 24 VAC/DC: approx VA (0.15 W) a 24 VAC approx. 1.0 W a 24 VDC 48 VDC: approx W a 48 VDC 100 o 125 VDC: approx. 0.5 W a 125 VDC Conrol oupus Conac oupu: 5 A a 250 VAC/30 VDC, resisive load (cosφ = 1) The minimum applicable load is 10mA a 5VDC (P reference value). Conac maerials : Ag-alloy Noe: 1. A power supply wih a ripple of 20% max. (single-phase power supply wih full-wave recificaion) can be used wih each DC Model. 2. Do no use an inverer oupu as he power supply. Refer o your OMRON websie for deails. 3. For conac inpu, use conacs which can adequaely swich 1 ma a 5 V. 44

45 H3CR-H Characerisics Accuracy of operaing ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 0.6 and 1.2 s) ime Seing error ±5% FS ±50 ms max. Operaion sar volage 30% max. of raed volage Influence of volage ±0.2% FS max. (±0.2% FS ±10 ms max. in ranges of 0.6 and 1.2 s) Influence of emperaure ±1% FS max. (±1% FS ±10 ms max. in ranges of 0.6 and 1.2 s) Insulaion resisance 100 MΩ min. (a 500 VDC) Dielecric srengh 2,000 VAC, 50/60 Hz for 1 min (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) 2,000 VAC, 50/60 Hz for 1 min (beween conrol oupu erminals and operaing ) 2,000 VAC, 50/60 Hz for 1 min (beween conacs of differen polariies) 1,000 VAC, 50/60 Hz for 1 min (beween conacs no locaed nex o each oher) Impulse wihsand volage Noise immuniy Saic immuniy Vibraion resisance Shock resisance Noe: Refer o he Life-es Curve(Reference). 5 kv (beween power erminals) for 100 o 120 VAC, 200 o 240 VAC, 100 o 125 VDC; 1 kv for 24 VAC/DC, 48 VDC 5 kv (beween curren-carrying erminal and exposed non-curren-carrying meal pars) for 100 o 120 VAC, 200 o 240 VAC, 100 o 125 VDC; 1.5 kv for 24 VAC/DC, 48 VDC ±1.5 kv (beween power erminals) and ±600 V (beween inpu erminals), square-wave noise by noise simulaor (pulse widh: 100 ns/1 μs, 1-ns rise); ±1 kv (beween power erminals) for 48 VDC Malfuncion: 8 kv, Desrucion:15 kv Desrucion: 10 o 55 Hz wih 0.75-mm single ampliude for 2 hrs each in hree direcions Malfuncion: 10 o 55 Hz wih 0.5-mm single ampliude for 10 min each in hree direcions Desrucion: 980 m/s 2 hree imes each in six direcions Malfuncion: 98 m/s 2 hree imes each in six direcions Ambien emperaure Operaing: 10 C o 55 C (wih no icing), Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Life expecancy Mechanical: 10 million operaions min. (under no load a 1,200 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 1,200 operaions/h) (See noe) EMC (EMI) EN Emission Enclosure: EN55011 Group 1 class A Emission AC Mains: EN55011 Group 1 class A (EMS) EN Immuniy ESD: IEC Immuniy RF-inerferenc: IEC Immuniy Burs: IEC Immuniy Surge: IEC Immuniy Conduced Disurbance: IEC Immuniy Volage Dip/Inerrupion: IEC Case color Ligh Gray (Munsell 5Y7/1) Degree of proecion IP40 (panel surface) Weigh Approx. 120 g Life-es Curve(Reference) Swiching operaions ( 10 3 ) 10,000 5,000 1, VDC L/R = 7 ms 250 VAC (cosφ = 0.4) 250 VAC/30 VDC (cosφ = 1) Load curren (A) Reference: A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ = 1) and a maximum curren of 0.1A can be swiched a 125V DC and L/R = 7ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC for H3CR-H8L/-HRL and 100 ma a 5 VDC for H3CR-H8RL (failure level: P). 45

46 Connecions H3CR-H Block Diagrams Wihou Rese Inpu (H3CR-H8L) Time range/ uni selecor AC (DC) inpu supply Oscillaion Couning failure deecion Indicaor LCD indicaor Wih Rese Inpu (H3CR-H8RL/-HRL) Time range/ uni selecor AC (DC) inpu supply Oscillaion Couning failure deecion Indicaor LCD indicaor Rese inpu Inpu I/O Funcions Inpus Rese Turns off he conrol oupu and reses he elapsed ime. s Conrol oupu Operaes insananeously when he power is urned on and ime-limi reses when he se ime is up afer he power is urned off. Terminal Arrangemen Noe: DC models, including 24 VAC/DC models, have polariy. 8-pin Models Wihou Rese Inpu (H3CR-H8L) Wih Rese Inpu (H3CR-H8RL) 11-pin Model Wih Rese Inpu (H3CR-HRL) Rese inpu Rese inpu supply supply Noe: Leave erminal 3 open. Do no use hem as relay erminals. supply Noe: Leave erminal 6 open. Do no use hem as relay erminals. 46

47 H3CR-H Operaion Timing Char : Se ime R: Minimum power ON ime (S-series: 0.1 s min.; M-series: 2 s min.) If he power ON ime is less han his value, he Timer may no operae (i.e., oupu may no urn ON). Model H3CR-H8L (See noe) ON OFF R Timing char R (1 3) (1 4) (8 6) (8 5) indicaor Li No li H3CR-H8RL (See noe) ON OFF R R 0.05 s min s min. Rese inpu ON (Shor-ed) OFF (Open) (8 6) (8 5) indicaor Li No li H3CR-HRL (See noe) Rese inpu ON OFF R 0.05 s min. R 0.05 s min. (1 3) (1 4) (11 9) (11 8) indicaor Li No li Noe: If he power is urned ON unil he se ime is up, he imer will be reriggered. 47

48 Nomenclaure H3CR-H Scale range display windows changes as below by urning he Time range selecor clockwise. indicaor (red) Scale range display windows Time seing knob (for seing power OFF-delay ime) Time range selecor (selec one from 0.6, 1.2, 6, and 12 a full scale) Time uni display S-series: sec M-series: min Dimensions Noe: All unis are in millimeers unless oherwise indicaed. H3CR-H8L H3CR-H8RL 15 (78) dia pins H3CR-HRL (78) dia pins Dimensions wih Fron Connecing Socke P2CF-08-@/P2CF-11-@ Dimensions wih Back Connecing Socke P3G-08/P3GA-11 H3CR-H8@L 101.3* 99 P2CF-08 P2CF-08-E 2.3* H3CR-HRL 112.2* P2CF-11 P2CF-11-E Noe: There are no resricions o he mouning direcion. * These dimensions vary wih he kind of DIN rack (reference value). 2.3* H3CR-H8@L + Adaper P3G-08 Y92F-30 (When Y92A-48G mouned) H3CR-HRL + Adaper P3GA-11 Y92F-30 (When Y92A-48G mouned) 48

49 H3CR-H Accessories (Order Separaely) Proecive Cover Y92A-48B To use he Proecive Cover wih a flush mouning, use he Y92F-30 flush mouning adapor. This Proecive Cover canno be used ogeher wih he Y92F-70/-71 flush mouning adapor or he panel cover. Hold-down Clip Y92H-2 The Y92H-2 Hold-down Clip is aached o he PF085A socke. Y92H-1 Y92H-1 Hold-down Clip is aached wih screws ogeher wih he PL08. 49

50 Safey Precauions (H3CR-H) Noe: The undermenioned is common for all H3CR-H models. Supplies The H3CR-H has a large inrush curren; provide sufficien power supply capaciy. If he power supply capaciy is oo small, here may be delays in urning ON he oupu. Wih he H3CR-H@RL, for he power supply of an inpu device, use an isolaing ransformer, of which he primary and secondary windings are muually isolaed and he secondary winding is no grounded. Correc (4) <7> 5, 6, 7 (1) <5> 2 H3CR-H@RL Inpu erminal (7) <10> 10 (2) <2> 2 supply ( ): H3CR-H8RL < >: H3CR-HRL Wiring H3CR-H The H3CR-H has a high impedance. Therefore, he H3CR-H may no be rese if he H3CR-H is influenced by inducive volage. In order o eliminae any influence of inducive volage, he wires conneced o he H3CR-H mus be as shor as possible and should no be insalled alongside power lines. If he H3CR-H is influenced by inducive volage ha is 30% or more of he raed volage, connec a CR filer wih a capaciance of approximaely 0.1 F and a resisance of approximaely 120 or a bleeder resisor beween he power supply erminals. If here is any residual volage due o curren leakage, connec a bleeder resisor beween he power supply erminals. Operaion An inerval of 3 s minimum is required o urn on he H3CR-H afer he H3CR-H is urned off. If he H3CR-H is urned on and off repeaedly wih an inerval of shorer han 3 s, abnormal heaing or burning may occur in inernal elemens. Incorrec Inpu device (4) <7> 5, 6, 7 (1) <5> 2 Isolaion ransformer is required. H3CR-H@RL Inpu erminal (7) <10> 10 (2) <2> 2 supply ( ): H3CR-H8RL < >: H3CR-HRL sae 1 sae 2 3 s min. Afer he forced rese funcion of he H3CR-H is acivaed, an inerval of 3 s minimum is required o acivae he forced rese funcion again. If he forced rese funcion is acivaed repeaedly wih an inerval of shorer han 3 s, he inernal pars of he H3CR-H may deeriorae and he H3CR-H may malfuncion. Inpu device Isolaion ransformer Inpu/ (H3CR-H@RL) An appropriae inpu is applied o he inpu signal erminal of he Timer when he inpu erminal for he inpu signal is shor-ed. Do no aemp o connec any inpu erminal o any erminal oher han he inpu erminal or o apply volage across oher han he specified inpu erminals or he inernal s of he Timer may be damaged. The H3CR-H@RL uses ransformerless power supply. When connecing a relay or ransisor as an exernal signal inpu device, pay aenion o he following poins o preven shor-ing due o a sneak curren o he ransformerless power supply. If inpu is made simulaneously from one inpu conac or a ransisor o he H3CR-H and a Timer whose common inpu erminals are used as power erminals, such as he H3CR-A, a shor- curren will be generaed. Eiher inpu hrough isolaed conacs, or isolae he power supply for one of he Timers. H3CR-H@RL 4*, 7 10, 7* Rese inpu If i is required ha he oupu be urned on repeaedly wih an inerval of shorer han 3 s, consider use of he H3CR-A in mode D (signal OFF-delay). On he H3CR-F@, do no se boh he ON se dial and OFF se dial o he lowes seings. Doing so may damage he conacs. Ohers 3 s min. 3 s min. If he H3CR-H is dropped or experiences some oher kind of shock, because a laching relay is used for oupu, conacs may be reversed or go ino a neural sae. If he H3CR-H is dropped, reconfirm correc operaion. G. 5 1*, 5 S. R. 6 7 H3CR-A 2, 2* 10 2 Shor- curren *: H3CR-H8RL ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To conver millimeers ino inches, muliply by To conver grams ino ounces, muliply by In he ineres of produc improvemen, specificaions are subjec o change wihou noice. 50

51 51 MEMO

52 Operaion (Common) Noe: The undermenioned is common for all H3CR models. Basic Seing Seing of Selecors The selecors can be urned clockwise and counerclockwise o selec he desired ime uni, ime range, or operaing mode. Each selecor has a snap mechanism ha secures he selecor a a given posiion. Se he selecor a a posiion a which i is secured. Do no se i midway beween wo securing posiions or a malfuncion could resul from improper seing. Selecion of Operaing Mode H3CR-A Mulifuncional Timer The operaion mode A o E, G, and J of he H3CR-A can be seleced. Use a Phillips head or flahead screwdriver o urn he selecor swich. The operaion mode can be se o one of eigh modes. The window on he op shows E, G, J, A, B, B2, C, or D o indicae he seleced mode. On he H3CR-A8, he window on he op shows E, J, B, A, or B2. Operaing mode selecor Usable screwdrivers Phillips head: No. 0-1 Fla head: Widh 2.3 o 3.0 mm (i.e., H3CR-A) Operaing mode display window Groove for screwdriver Selecion of Time Uni and Time Range H3CR-A Mulifuncional Timer The desired ime uni (sec, 10 s, min, 10 m, hrs, or 10 h) is displayed in he window below he ime seing knob by urning he ime uni selecor locaed a he lower righ corner of he fron panel. A ime range (1.2, 3, 12, or 30 for H3CR-A@/2.4, 6, 24, or 60 for H3CR-A@-301) is seleced wih he ime range selecor a he lower lef corner of he fron panel, and he seleced ime range appears (in he window a he lower righ par) wihin he plasic frame of he ime seing knob. H3CR-F Twin Timers The display window a he boom righ inside he Time seing knob shows 1.2, 3, 12, or 30 o indicae he scale number seleced wih he selecor swich on he fron a boom lef. Time range selecor Use a Phillips head or flahead screwdriver o urn he selecor swich. For ON-ime, he desired ime uni (sec, 10 s, min, 10 min, hrs, and 10 h) is indicaed in he ON-ime uni display window a he lower righ corner of he fron panel and can be changed by urning he ON-ime uni selecor locaed below he ON-ime uni display window. Scale range display windows Time range selecor OFF-ime seing knob (wih green poiner) For OFF-ime seing OFF-ime uni display window OFF-ime uni selecor ON-ime uni display window ON-ime uni selecor For OFF-ime, he desired ime uni (sec, 10 s, min, 10 min, hrs and 10 h) is indicaed in he OFF-ime uni display window a he upper righ corner of he fron panel and can be changed by urning he OFF-ime uni selecor locaed below he OFF-ime uni display window. Time seing knob OFF-ime uni selecor Time range selecor Scale range display window Time uni selecor Time uni display window 52

53 H3CR H3CR-G Sar-dela Timers The display window a he boom righ inside he Time seing knob shows 6, 12, 60, or 120 o indicae he scale number Sar operaion ime seleced wih he selecor swich on he fron a boom lef. H3CR-H OFF-delay Timers Use a Phillips head screwdriver or flahead screwdriver o urn he selecor swich. The display window a he boom righ inside he Time seing knob shows 0.6, 1.2, 6, or 12 o indicae he scale number seleced wih he selecor swich on he fron a boom lef. Sar operaion ime range selecor Scale range display window Time seing knob Time range selecor Use a Phillips head screwdriver or flahead screwdriver o urn he selecor swich. The display window a he boom cener of he Time seing knob shows 0.05, 0.1, 0.25, 0.5, 0.75, or 1.0 o show he sar -dela ransfer ime seleced wih he selecor swich on he fron a boom righ. Seing of Time Usable screwdrivers Phillips head: No. 0-1 Fla head: Widh 2.3 o 3.0 mm Use he ime seing knob o se he desired ime. Scale range display window Sar operaion ime range selecor Sar-dela swiching ime display window Time seing knob Sar-dela swiching ime selecor swich Usable screwdrivers Phillips head: No. 0-1 Fla head: Widh 2.3 o 3.0 mm Using he Time Seing Ring for H3CR-A/-G Locking he Se Time Moun he Panel Cover on he Timer, se he desired ime wih he ime seing knob, and place Time Seing Ring A ono he ime seing knob so ha he ime seing noch of Time Seing Ring A is in he cener of he rese lock posiion of he Panel Cover. Time seing noch Rese lock posiion Limiing he Seing Range Example: To se a range of 10 and 20 s. Moun he Panel Cover on he Timer, se he ime seing knob o 10 s (he lower limi of he seing range), and place Time Seing Ring C ono he ime seing knob so ha he sopper of Time Seing Ring C is on he righ edge of he rese lock posiion of he Panel cover. Nex, se he ime seing knob o 20 s (he upper limi of he seing range), place Time Seing Ring B ono he ime seing knob so ha he sopper of Time Seing Ring B is on he lef edge of he rese lock posiion of he Panel Cover. Sopper Rese lock posiion Time Seing Ring A Panel cover Time seing noch Seing posiion Time Seing Ring B Time Seing Ring C Panel cover Range Example: To se he ime o 10 s. 53

54 Accessories (Order Separaely) (Common) H3CR Noe: The undermenioned is common for all H3CR models. Noe: All unis are in millimeers unless oherwise indicaed. Flush Mouning Adapor Y92F-30 Panel P3G Back Connecing Socke Noe1: The adapers for wo or more imers mouned in a verical line are differen in orienaion from hose mouned in a horizonal line. N can be obained as follows (n: he number of H3CR models arranged side by side) Wihou a Cover: N = (48n - 2.5) +1 /-0 Wih he Proecive Cover: N = (51n - 5.5) +1 /-0 Wih he Panel Cover: N = (50n - 4.5) +1 /-0 Noe2: The applicable hickness of he mouning panel mus be 1 o 5 mm Panel Cuou (Conforms ro DIN 43700) 0.5 R max (N) Y92F-70/-73 Panel P3G Back Connecing Socke Panel Cuou Adaper mouning hole Two, 4.5 dia ±0.15 R0.5 max. 52 o 53 45± (63.7) (See noe.) Uni inserion direcion* 65 o 66 76±0.2 Y92F-71/ Noe: The value shown in parenheses is for he Y92F-70. Panel P3G Back Connecing Socke Noe: The applicable hickness of he mouning panel mus be 1 o 3.2 mm. * Inser imer uni from back side of adaper. R0.5 max ± ± (63.7) (See noe.) Noe: The value shown in parenheses is for he Y92F-71. Uni inserion direcion* Noe: The applicable hickness of he mouning panel mus be 1 o 3.2 mm. * Inser imer uni from back side of adaper. 54

55 H3CR Track Mouning/Fron Connecing Socke P2CF-08 Eigh, M sems max max. P2CF-08-E (Finger Safe Terminal Type) Conforming o VDE0106/P100 Eigh, M sems Two, 4.5 dia. holes max Terminal Arrangemen/ Inernal Connecions (Top View) Surface Mouning Holes Two, 4.5 dia. or wo, M4 40± max. Two, 4.5 dia. holes ± max max. Track Mouning/Fron Connecing Socke P2CF-11 Eleven, M sems max Terminal Arrangemen/ Inernal Connecions (Top View) Surface Mouning Holes 4 50 max. P2CF-11-E (Finger Safe Terminal Type) Conforming o VDE0106/P max. Two, 4.5 dia. or wo, M4 40±0.2 Eleven, M sems max. Two, 4.5 dia. holes ± max max. 55

56 Back Connecing Socke H3CR P3G dia. Terminal Arrangemen/ Inernal Connecions (Boom View) P3GA dia. Terminal Arrangemen/ Inernal Connecions (Boom View) Finger Safe Terminal Cover Conforming o VDE0106/P100 Y92A-48G (Aachmen for P3G-08/P3GA-11 Socke) Twelve, 6.4 dia. holes Mouning Track PFP-100N, PFP-50N PFP-100N ± ±0.3 27± ± ,000 (500) 10 (See noe) 15 (5) (See noe) , Noe: The values shown in parenheses are for he PFP-50N. End Plae PFP-M Spacer PFP-S M4 x 8 pan head screw