AJ- P. Operating Instructions. Digital Video Cassette Recorder. Printed in Japan VQT S0699W3119 A OFF CH1 CH2 CH2 RESET COUNTER CH3 CH4

Transcription

1 DIGITAL VIDEO CASSETTE REMOTE Digial Video Cassee Recorder AJ- P Operaing Insrucions ON OFF POWER EJECT INPUT SELECT S-VIDEO LINE OPTION BEGIN END AUDIO REC LEVELE CH1 Digial Video Cassee Recorder MENU LOCAL REMOTE AUDIO OUT SELECT CH3 CH4 CH2 CH1 CH2 REC INH REMOTE db CTL WIDE DV TC SERVO REW STOP UB HOURS MINUTES SECONDS FRAMES MODE DOWN UP SET FF MENU DATA PLAY PAUSE/STTIL + REC RESET COUNTER Prined in Japan VQT S0699W3119 A P

2 IMPORTANT Unauhorized recording of copyrighed elevision programs, video apes and oher maerials may infringe he righ of copyrigh owners and be conrary o copyrigh laws. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lighning flash wih arrowhead symbol, wihin an equilaeral riangle, is inended o aler he user o he presence of uninsulaed dangerous volage wihin he produc s enclosure ha may be of sufficien magniude o consiue a risk of elecric shock o persons. The exclamaion poin wihin an equilaeral riangle is inended o aler he user o he presence of imporan operaing and mainenance (service) insrucions in he lieraure accompanying he appliance. CAUTION: Do no insall or place his uni in a bookcase, buil-in cabine or in anoher confined space in order o keep well venilaed condiion. Ensure ha curains and any oher maerials do no obsruc he venilaion condiion o preven risk of elecric shock or fire hazard due o overheaing. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL. FCC Noe: This device complies wih Par 15 of he FCC Rules. To assure coninued compliance follow he aached insallaion insrucions and do no make any unauhorized modificaions. This equipmen has been esed and found o comply wih he limis for a class A digial device, pursuan o Par 15 of he FCC Rules. These limis are designed o provide reasonable proecion agains harmful inerference when he equipmen is operaed in a commercial environmen. This equipmen generaes, uses, and can radiae radio frequency energy and, if no insalled and used in accordance wih he insrucion manual, may cause harmful inerference o radio communicaions. Operaion of his equipmen in a residenial area is likely o cause harmful inerference in which case he user will be required o correc he inerference a his own expense. indicaes safey informaion. $ Do no inser fingers or any objecs ino he video cassee holder. $ Avoid operaing or leaving he uni near srong magneic fields. Be especially careful of large audio speakers. $ Avoid operaing or soring he uni in an excessively ho, cold, or damp environmen as his may resul in damage boh o he recorder and o he ape. $ Do no spray any cleaner or wax direcly on he uni. $ If he uni is no going o be used for a lengh of ime, proec i from dir and dus. $ Do no leave a cassee in he recorder when no in use. $ Do no block he venilaion slos of he uni. $ Use his uni horizonally and do no place anyhing on he op panel. $ Cassee ape can be used only for one-side, one direcion recording. Two-way or wo-rack recordings canno be made. $ Cassee ape can be used for eiher Color or Black & Whie recording. $ Do no aemp o disassemble he recorder. There are no user serviceable pars inside. $ If any liquid spills inside he recorder, have he recorder examined for possible damage. $ Refer any needed servicing o auhorized service personnel. 2

3 Conens Inroducion Feaures Pars and Their Funcions Fron panel Connecor panel Tapes Operaion Turning on he power/insering a cassee STOP mode Recording Pause/recording (frame-o-frame coninuiy) Playback Cue/review Sill picure playback Frame by frame advance Audio swiching REC CHECK Repea playback Time Codes and User s Bi Time codes User s bi Seing he ime code Seing he user s bi Playing back he ime code/user s bi Superimposed Screens Seup (Iniial Seings) How o perform he seings using he on-screen menus How o resore he facory seings How o se he user defaul seings How o load he user defaul seings How o iniiae he menu proec mode How o release he menu proec mode How o display he DIAG menu Seup Menus SYSTEM menu BASIC menu OPERATION menu INTERFACE menu TAPE PROTECT menu TIME CODE menu VIDEO menu AUDIO menu Ediing Audio ediing funcions Cuing V-fading Firs Edi Funcion RS-232C Hardware specificaions ) Inerface specificaions ) Communicaion parameers Sofware specificaions ) Exernal inerface specificaions ) Sending forma (compuer VTR) ) Receiving forma (VTR compuer) ) Command lis ) Checkpoins for RS-232C communicaion.. 73 Error Messages Emergency Ejec Video Head Cleaning Condensaion Mainenance Specificaions

4 Inroducion The AJ-D250 is a digial VTR which uses 1/4 wide apes. The incorporaion of digial compression echnology ensures ha he deerioraion in picure and sound qualiy suffered during dubbing will be much less han wih convenional analog sysems. The model has a compac and lighweigh design, enabling i o be readily carried abou or easily insalled in a rack. The ineracive sysem, which is feaured for he uni s seings, enables hese seings o be performed while viewing he menus on he TV monior screen. The model AJ-D250 comes wih an RS-232C connecor which makes i possible o conrol he ediing operaions and exercise remoe conrol from a compuer using he RS-232C remoe conrol (AJ-A250 - available as an opional accessory). Feaures Compac and ligh This uni is 8 7 /16 (214 mm) wide, 5 1 /4 (132 mm) high and 15 7 /16 (391 mm) deep, and weighs 14.3 lb (6.5 kg). I is equipped wih grips so ha i can be carried easily. Assemble ediing and inser ediing Using he RS-232C remoe conrol (AJ-A250 - available as an opional accessory), wo unis one a player and he oher a recorder can be conrolled direcly from he remoe conrol o perform ediing operaions. Encoder conrol The video oupu signals can be adjused using he iems on he seup menus. 2-channel digial audio wih high sound qualiy RS-232C conrol Use of he RS-232C remoe conrol (AJ-A250 - available as an opional accessory) enables no only ediing operaions o be performed bu remoe conrol can also be exercised, from a compuer by connecing he RS-232C cable beween from he compuer and his VTR. Compaible wih consumer-use equipmen Using he cassee adaper (AJ-CS750P: opional accessory), consumer-use cassee apes sho using a consumer-use digial camera can be played back on his uni. The LP mode is no suppored. Time codes The uni comes wih a buil-in ime code generaor (TCG)/ime code reader (TCR). Repea playback Any secion on a ape can be played back repeaedly for an unlimied number of imes or one ime only. Menu-driven seup The uni s seings are performed using an ineracive sysem while viewing he menus on he TV monior screen. Remoe conrol The uni can be operaed from disances up o 5 meers away when he AG-A11 remoe conrol (opional accessory) is conneced. Up o 184 minues of recording The uni uses wo ypes of cassee apes: one for news gahering (max. 66 minues) and he oher for general-purpose applicaions (184 minues: using AJ- 5P92LP ). The uni s compac design accommodaes apes wih a 1/4 widh. For AJ-5P92LP cassee apes, use a VTR supporing DVCPRO (25 Mbps) 184 minue apes. 4

5 Pars and Their Funcions Fron panel Couner display : REC INH REMOTE WIDE DV db CTL CH 1 CH 2 TC UB SERVO HOURS MINUTES SECONDS FRAMES ; < = > ON EJECT OFF POWER DIGITAL VIDEO CASSETTE INPUT SELECT S-VIDEO LINE OPTION AUDIO REC LEVEL BEGIN END CH 1 Digial Video Cassee Recorder MENU LOCAL REMOTE AUDIO OUT SELECT CH 3 CH 4 CH 2 REW STOP FF PLAY PAUSE/STILL REC MODE DOWN MENU UP - DATA + SET RESET COUNTER A B D C E F G H I J K L O M N 5

6 Pars and Their Funcions Fron panel 1 POWER swich When he ON side is pressed, power is supplied o he uni, and he couner display is illuminaed. 2 Cassee inserion slo News gahering cassees, general-purpose cassees and consumer-use cassees accompanied by he adaper are insered ino his slo. Consumer-use cassees can be used for playback only. 3 EJECT buon When his buon is pressed, he ape is unloaded, and a few seconds laer i is auomaically ejeced. If he couner display is se o he CTL display, he display will be rese. 4 REC/REC INH lamp REC: The lamp lighs during recording. REC INH: The lamp lighs when he accidenal cassee erasure prevenion saus is esablished. I also lighs when ON is seleced as he REC INHIBIT seing on he seup menu. Recording canno be conduced while his lamp is lighed. 5 REMOTE lamp This lamp lighs when he LOCAL/MENU/REMOTE swich has been se o REMOTE. 6 WIDE lamp This lamp lighs in he 16:9 wide screen mode. 7 Consumer-use cassee inserion lamp This lamp lighs when a cassee recorded using a consumer-use DV device has been insered. 8 REPEAT lamp This lamp lighs during repea playback. 9 SERVO lamp This lamp lighs when he drum servo and capsan servo are locked. : Channel saus lamps One of hese lamps lighs depending on he error rae saus. (Green Blue Red) Green: This lamp lighs when he error rae for boh he video and audio playback signals is a an accepable level. Blue: This lamp lighs when he error rae for eiher he video or audio playback signals has deerioraed. A normal playback picure appears even when he lamp is lighed. Red: This lamp lighs when eiher he video or audio playback signals have become subjec o correcion or inerpolaion. ; Level meer This indicaes he levels of he audio signals. During recording or E-E selecion, i indicaes he audio inpu signal levels; during playback, i indicaes he audio oupu signal levels. < Cassee inserion lamp This lamp lighs when a cassee has been insered ino he uni. = Couner display The ime codes, CTL coun values and on-screen informaion and oher messages appear on his display. > LOCAL/MENU/REMOTE swich This swich is se when he menu seings are o be performed or when he uni is o be conrolled from an exernal source. LOCAL: MENU: Se here when he uni is o be conrolled using he conrols provided on he uni s operaion panel. Se here when he on-screen menu iems are o be se. REMOTE: Se here when he uni is o be conrolled using he RS-232C inerface or oher exernal conrol device.? INPUT SELECT swich This is used o selec he inpu signals. LINE: Se here o record he signals which are supplied o he video signal inpu connecor. S-VIDEO: Se here o record he signals which are supplied o he S-VIDEO inpu connecor. OPTION: Se here o supply video and audio signals from he opional board and record BEGIN buon This buon ses he sar poin for repea playback and i indicaes he sar poin which is currenly enered. A END buon This buon ses he end poin for repea playback and i indicaes he end poin which is currenly enered. B CH3/CH4 lamps These lamps ligh when he audio signals have been se o CH3 and CH4 during DV forma playback. C AUDIO OUT SELECT buon This buon selecs he audio signals which are o be oupu. 6

7 Pars and Their Funcions D Headphones jack When headphones are conneced o his jack, hey can be used o monior he sound being recorded or played back. E Volume conrol This is used o adjus he volume o he headphones. F Audio recording level conrols These conrols are used o adjus he recording level for PCM audio signals CH1 and CH2. G REW buon When his buon is pressed, he ape is rewound, and he playback picures can be moniored if TAPE has been seleced for he S/F/R EE SEL seup menu iem seing. H STOP buon When his buon is pressed, he ape sops raveling, and he sill picure can be moniored when he TAPE seing has been seleced for he S/F/R EE SEL seup menu iem. In he sop mode, he drum sill coninues o roae, and he ape remains ighly wrapped around he drum. When he designaed period of ime has elapsed in he sop mode, he uni is auomaically se o he sandby OFF mode in order o proec he ape. I FF buon When his buon is pressed, he ape is fasforwarded, and he playback picures can be moniored if TAPE has been seleced as he S/F/R EE SEL seup menu iem seing. J PLAY buon When his buon is pressed, playback is commenced. Recording is commenced when i is pressed ogeher wih he REC buon. K PAUSE/STILL buon When his buon is pressed during recording, recording is sopped emporarily. When i is pressed again, recording is resumed. When his buon is pressed during playback, he sill picure mode is esablished. When i is pressed again, playback is resumed. L REC buon Recording is commenced when his buon is pressed ogeher wih he PLAY buon. When i is pressed during playback or in he STOP mode or sandby OFF mode, he REC CHECK mode is esablished. (See page 15) M REMOTE connecor When he remoe conrol (AG-A11) is plugged ino his connecor, he uni can be operaed a a disance using he conrols on he remoe conrol insead of he uni s funcion buons. Keep he LOCAL/MENU/REMOTE swich a he REMOTE posiion. e Recorder PAUSE/STILL AJ- REC DATA + SET RESET COUNTER REMOTE Panasonic (AG-A11) N COUNTER buon This buon is used o swich he couner display. CTL: Se here o display he ape imer (conrol signal). TC: Se here o display he ime code. UB: Se here o display he user s bi. Remaining ape: Se here o display he amoun of remaining ape. O RESET buon When his buon is pressed in he CTL mode, he couner display is rese o 00:00:00:00. 7

8 Pars and Their Funcions Connecor panel INPUT S-VIDEO VIDEO REF VIDEO AUDIO CH1 CH2 RS- 232C OUTPUT S-VIDEO VIDEO VIDEO MONIT AUDIO 1 CH1 CH2 AUDIO 2 CH1 CH2 AC IN SIGNAL GND > 9 < : = ; 2 1 8

9 Pars and Their Funcions Connecor panel 1 AC IN socke Plug one end of he uni s power cord ino his power socke. 2 SIGNAL GND erminal In order o reduce noise, connec his erminal o he signal grounding erminal on one of he devices o which he uni is conneced. This is no a safey ground. 3 Fan moor This moor is used o cool he uni. 4 Grip This grip is fied on he side panel. When operaing he uni, however, place he uni fla on is boom surface. 5 S-VIDEO IN connecor The S-VIDEO video signals are supplied o his connecor. 6 VIDEO IN connecor The analog video signals are supplied o his connecor. 7 REF VIDEO IN connecor This is conneced o he reference video signal when he uni is o be synchronized wih he reference sync signals of an exernal uni during playback. 8 AUDIO IN connecors The analog audio signals are supplied o his connecor. 9 S-VIDEO OUT connecor The S-VIDEO video signals are oupu from his connecor. : VIDEO OUT connecor The analog video signals are oupu from his connecor. ; MONITOR OUT connecor The video monior signals are oupu from his connecor. Superimposed video signals can be oupu. < AUDIO 1 OUT connecors The analog audio signals are oupu from his connecor. = AUDIO 2 OUT connecors The analog audio signals are oupu from his connecor. > RS-232C connecor Ediing operaions can be conduced speedily and efficienly by connecing he RS-232C remoe conrol (AJ-A250 - available as an opional accessory) o his connecor. Various operaions can be performed from a compuer by using he RS-232C cable which is available as an opional accessory. RS-232C connecor RS- 232C INPUT S-VIDEO OUTPUT S-VIDEO AUDIO 1 CH1 CH2 VIDEO VIDEO REF VIDEO AUDIO CH1 CH2 VIDEO MONIT AUDIO 2 CH1 CH2 AC IN SIGNAL GND 9

10 DIGITAL VIDEO CASSETTE Tapes Tape Descripion Consumer-use cassees (S cassee) M cassees L cassees These apes are designed o be used exclusively wih consumer-use camera recorders. They can be used only for playback on his uni and only wih he cassee adaper (opional accessory). Long-playing apes (80 min. in sandard mode, 120 min. in LP mode) canno be used wih his uni. I is recommended ha Panasonic brand consumer-use DV apes be used. Remember ha insering a cassee ape wihou using he cassee adaper can cause malfuncioning. Tapes wih up o 66 minues of recording/playback ime (AJ-P12MP, AJ-P24MP, AJ-P33MP, AJ-P46MP, AJ-P66MP) Tapes wih up o 184 minues of recording/playback ime (AJ-P34LP, AJ-P66LP, AJ-P94LP, AJ-P126LP, AJ-5P92LP ) For AJ-5P92LP cassee apes, use a VTR supporing DVCPRO (25 Mbps) 184 minue apes. ON OFF POWER Digial Video Cassee Recorder LOCAL EJECT MENU REMOTE Align he cassee wih he cener of he inserion slo, and push i in genly. The cassee ape is loaded auomaically. INPUT SELECT S-VIDEO LINE OPTION AUDIO REC LEVEL BEGIN END CH 1 AUDIO OUT CH 2 SELECT CH 3 CH 4 RESET COUNTER REW STOP FF PLAY PAUSE/STILL REC MODE DOWN MENU UP - DATA + SET REMOTE M cassee L cassee <Checkpoins for consumer-use DV ape playback> OConsumer-use DV apes can be used for playback only. O Consumer-use apes recorded in he LP mode canno be played back. ORecording ono consumer-use apes is no possible, herefore he recording-relaed funcions are inhibied. OThe maximum speed a which consumer-use apes can be forwarded or reversed is 32 imes normal ape speed. O The sill picures of consumer-use apes are subjec o disurbance. OIn he ineres of proecing he apes, i is recommended ha consumer-use ape cue-up be kep o he minimum exen possible. OThe maximum ime for he STILL TIMER when a consumer-use ape is used has been se o 10 seconds. When he uni has been lef sanding in he STILL mode, he sandby OFF (half loading) mode will be esablished afer one minue has elapsed. ODuring consumer-use ape search and sill picure operaions, a display indicaing ha he ime code canno be read may appear. 10

11 Operaion Turning on he power/insering a cassee Before proceeding o operae he uni, make sure ha he uni has been conneced properly. 1 Turn 2 Inser 3 Check on he uni s power. he cassee ape. Inser i a he prescribed posiion wihou forcing i in any way. ha he STOP lamp is lighed. When he ape is insered, he cylinder sars roaing auomaically, he ape is loaded, and he STOP mode is esablished. I is possible o change he mode when a ape is insered using he seings in Iem No. 104 TAPE IN MOD of he Seup menu. (See page 29) 1 2 ON EJECT OFF POWER DIGITAL VIDEO CASSETTE INPUT SELECT S-VIDEO LINE OPTION AUDIO REC LEVEL BEGIN END CH 1 Digial Video Cassee Recorder MENU LOCAL REMOTE AUDIO OUT SELECT CH 3 CH 4 CH 2 REW STOP FF PLAY PAUSE/STILL REC DOWN UP DATA MENU MODE - + SET RESET COUNTER REMOTE 3 11

12 Operaion STOP mode 1 When he STOP buon is pressed, he STOP mode is esablished. The STOP lamp lighs, and he ape sops raveling. OIn order o proec he ape, he ape proecion mode will be esablished when he ime seleced for he STILL TIMER seup menu iem seing has elapsed. (See page 31) When he STOP, REW, FF or PLAY buon is pressed, he corresponding mode will be esablished. <Checkpoin for STILL TIMER seing> ORepeaedly using he same locaions on he same ape will increase he cumulaive sandby ime a hose locaions. In he ineres of proecing he ape, keep he sandby imes a he same locaions as shor as possible. ON EJECT OFF POWER DIGITAL VIDEO CASSETTE INPUT SELECT S-VIDEO LINE OPTION AUDIO REC LEVEL BEGIN END CH 1 Digial Video Cassee Recorder MENU LOCAL REMOTE AUDIO OUT SELECT CH 3 CH 4 CH 2 REW STOP FF PLAY PAUSE/STILL REC DOWN UP DATA MENU MODE - + SET RESET COUNTER REMOTE 1 12

13 Operaion Recording 1 Se 2 Press 3 Check 4 Selecing 5 Press 6 Press he accidenal erasure prevenion ab on he cassee ape o recording, and inser he ape. he STOP buon o se he uni o he STOP mode. ha he REC INH lamp has gone off. he video and audio inpu signals and adjusing he audio levels Selecing he video and audio inpu signals 1 Connec he signals which are o be recorded. 2 Selec he inpu signals using he INPUT SELECT swich on he fron panel. Adjusing he audio levels 1 Adjus he levels of he audio inpu signals. The audio signals are recorded a he proper levels when he level conrols are a heir cener-click posiions. he PLAY buon while holding down he REC buon. The REC and PLAY lamps ligh and recording commences. he STOP buon o end he recording. The recording now ends, and he STOP mode is esablished. <Noes> OIf recording prevenion signals are included among he inpu signals, he inpu signals will no be recorded properly. OCheck ha he SERVO lamp has lighed during recording. The image which is played back will be disurbed if he lamp is flashing or off. 13

14 Operaion Pause/record (frame-o-frame coninuiy) 1 Press 2 Press 3 Press he PAUSE/STILL buon while he cassee ape is playing. When ON has been seleced as he AUTO BACK seup menu iem seing, he ape will be rewound for abou 2 seconds saring from he posiion where he PAUSE/STILL was pressed. (See page 29) he REC buon o se he uni o he REC PAUSE mode. The monior display now swiches o he E-E screen. he PAUSE/STILL buon o commence recording. The ape ravels o he posiion where he PAUSE/STILL was pressed in sep 1 above, and recording commences. The E-E screen is now displayed. Playback 1 Inser 2 Press 3 Press he cassee ape. he PLAY buon. Normal playback is now commenced. he STOP buon o end he playback. The uni is now se o he STOP mode. Check ha he SERVO lamp has lighed during playback. The playback image will be disurbed if he lamp is off or flashing. Cue/review Hold down he FF or REW buon during playback. While his buon is pressed, he ape will be cued or reviewed a abou 10 imes he normal ape speed. Normal playback is resored when he buon is released. OWhen ON has been seleced as he SEARCH CUE seup menu iem seing, he CUE rack sound will be oupu during cue or review. (See page 34) Sill picure playback Press he PAUSE/STILL buon during playback. Normal playback is resored when he PAUSE/STILL buon is pressed again. O No sound will be heard during sill picure playback. 14

15 Operaion Frame by frame advance When he FF or REW buon is pressed during sill picure playback, he ape will be advanced forward or backward one frame a a ime. ONo sound will be heard during frame by frame advance. Audio swiching The AUDIO OUT SELECT buon is used o swich o he desired sound. By pressing his buon, he audio oupu is swiched o he modes in he sequence shown below. Mode AUDIO OUT connecors CH1 oupu CH2 oupu Display ube LED A CH1 CH2 CH1 CH2 CH3 CH4 B CH1 CH1 CH3 CH4 C CH2 CH2 CH3 CH4 D CH3 CH4 No display CH3 CH4 E CH3 No display CH3 CH4 F CH4 No display CH3 CH4 G CH1+CH3 CH2+CH4 CH1 CH2 CH3 CH4 The seings in he boxes ( 4-channel mode playback. ) are valid only during DV forma OFF ON Sequence in which he modes are seleced [. A > B > C > D > E > F > G.] a"""""""""""""""""""""" } REC CHECK By pressing he REC buon during playback or in he STOP or STANDBY OFF mode, i is possible o check he audio inpu signals, ime code generaor value and he video inpu signals which have been seleced using he INPUT SELECT swich. O REC CHECK during playback The REC CHECK mode is esablished while he REC buon is held down. Normal playback is resored when he buon is released. OREC CHECK in he STOP or STANDBY OFF mode The REC CHECK mode is esablished when he REC buon is pressed. To release he mode, press he STOP buon. 15

16 Operaion Repea playback Seing he BEGIN and END poins [Menu mode] 1 Se Selec 5 The 6 Press 7 Se he uni o he menu mode (by seing he LOCAL/MENU/REMOTE swich o he MENU posiion). Selec he BGN PRESET or END PRESET seup menu iem, and press he DATA+ buon (PAUSE/STILL buon) or DATA buon (PLAY buon). (See page 29) I is possible o selec wheher he BEGIN or END poin is o be se or no by operaing he DATA+ or DATA buon. Selec TC or CTL using he COUNTER buon. If he RESET buon is pressed while he uni is in CTL mode, 00:00:00:00 will be se. he digi o be changed (blinking display) using he UP buon (FF buon) or DOWN buon (STOP buon). The frame digis canno be seleced. They always appear as 00. value is incremened or decremened using he DATA+ buon (PAUSE/STILL buon) or DATA buon (PLAY buon). he SET buon (REC buon) upon compleion of he seings. The seings are now sored in he memory. he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. <Noes> O : : : appears on he display when he poins have no been se. In his case, repea playback will sar a he beginning of he ape which serves as he BEGIN poin and end a he end of he ape which serves as he END poin. OWhen he MODE buon (REW buon) is pressed insead of he SET buon upon compleion of he seings, he ime code seing will be canceled. 16

17 Operaion Seing he BEGIN and END poins [Fron panel] 1 Se 2 When he uni o he local mode (by seing he LOCAL/MENU/REMOTE swich o he LOCAL posiion). he BEGIN or END buon on he fron panel is pressed, he curren posiion is se as he BEGIN or END poin. Displaying he BEGIN and END poins 1 Se he uni o he remoe mode (by seing he LOCAL/MENU/REMOTE swich o he REMOTE posiion). 2 When he BEGIN or END buon on he fron panel is pressed, he BEGIN or END poin is displayed while he buon is held down. The seings are no changed. Seing he repea playback mode 1 Se he uni o he menu mode (by seing he LOCAL/MENU/REMOTE swich o he MENU posiion). 2 Selec he MEMORY MODE seup menu iem, and selec he repea playback mode. (See page 29) Seing Operaion OFF M-STOP REPT1 CONT Normal operaion The ape sops near he BEGIN poin when i is fas-forwarded or rewound. When he ape playback reaches he END poin, he ape is rewound o he BEGIN poin, where i sops. When he ape playback reaches he END poin, he ape is rewound o he BEGIN poin and playback is repeaed. 3 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. <Noes> OThe picure qualiy will deeriorae when he same ape is repeaedly played back over and over again. As a general guideline, replace he ape wih a new one afer abou 100 repea playback operaions. OWhen repea playback is o be iniiaed using a consumer-use ape, he uni will no operae even if CONT has been seleced as he seup menu iem No.111 MEMORY MODE seing. (See page 29) 17

18 Time Codes and User s Bi Time codes Time codes are used when recording ime code signals generaed by he ime code generaor on he ape, reading ou heir values wih he ime code reader, and displaying he absolue posiions of he ape in incremens of hours, minues, seconds and frames. The ime codes are wrien in he sub-code area (daa area) of he helical rack. For his reason, hey can be read a any playback speed from he sop mode o slow-moion playback or highspeed playback. The ime code value is indicaed on he display or superimposed. TCR 00 : 07 : 04 : 24 Hours Minues Seconds Frames User s bi The user s bi is he 32-bi (8-digi) daa frame in he ime code signal which is made available o users. I can record operaor numbers, ec. The characers which can be used for he user s bi are 0 o 9 and A B C D E F. 18

19 Time Codes and User s Bi Seing he ime code 1 Se 2 Selec 3 Selec 4 The 5 Press 6 Se he uni o he menu mode (by seing he LOCAL/MENU/REMOTE swich o he MENU posiion). he TC PRESET seup menu iem, and press he DATA+ buon (PAUSE/STILL buon) or DATA buon (PLAY buon). (See page 32) he digi o be changed (blinking display) using he UP buon (FF buon) or DOWN buon (STOP buon). value is incremened or decremened using he DATA+ buon (PAUSE/STILL buon) or DATA buon (PLAY buon). he SET buon (REC buon) upon compleion of he seings. he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. <Noes> OThe curren ime code value appears as he defaul value. OWhen he RESET buon is pressed while he digi o be changed is blinking, he display is rese o 00:00:00:00. OThe ime code canno be se unless P-REC or P-FREE has been seleced as he TC MODE seup menu iem seing. (See page 32) OIf he MODE buon (REW buon) is pressed insead of he SET buon while he digi o be changed is blinking, he ime code seing will be canceled. Seing he user s bi 1 Se 2 Selec he uni o he menu mode (by seing he LOCAL/MENU/REMOTE swich o he MENU posiion). he UB PRESET seup menu iem, and press he DATA+ buon (PAUSE/STILL buon) or DATA buon (PLAY buon). (See page 32) Now follow he same procedure as for seing he ime code. 19

20 Time Codes and User s Bi Playing back he ime code/user s bi 1 Se 2 Se he uni o he STOP mode. o TC or UB using he COUNTER buon. TC: The ime code appears on he display. UB: The user s bi appears on he display. OInerpolaion is provided by he CTL signal if he ime code canno be read. 3 Press he PLAY buon. Playback is commenced, and he ime code appears on he display. When ON has been seleced as he SUPER seup menu iem seing, he ime code value will be superimposed ono he video signals which are oupu from he MONITOR OUT connecor. (See page 28) <Noes> OThe colon beween he seconds and frames changes o a period when a drop frame ime code is read. O Inerpolaion is auomaically provided by he CTL signal if he ime code signal is missing. The display appearing a his ime will be as shown below. T R 00 : 07 : 04 : 24 The colon beween he seconds and frames changes o a period in he case of a drop frame. appears here when he ime code signal is missing. (Superimpose only) 20

21 Superimposed Screens When he uni s MONITOR OUT connecor has been conneced o a TV monior, he conrol signals, ime codes, ec. are displayed on he TV monior screen as abbreviaions. The display can be swiched ON or OFF using he seup menu iem No. 000 seing. (See page 28) Display posiion The posiion where he superimposed display appears can be changed using seup menu iem No.002 CHARA H-POS and No.003 (CHARA V-POS). (See page 28) TV monior TCR : : : No display: Normally, no display S: Appears wih FAN STOP. L: Appears wih LOW RF. N: Appears wih NO RF. TCR : : : TV monior TCR : : : TV monior Abbreviaion CTL: conrol signal TCR: ime code playback value UBR: user s bi playback value REM: remaining ape amoun Characers displayed The background of he characers superimposed ono he display can be changed using he seup menu iem No.004 CHARA TYPE seing. (See page 28) When he MODE buon and he DATA+ buon or DATA buon are pressed, he couner display appears emporarily while he buons are held down so ha he seing can be checked. Even while he MODE buon is held down, seings can sill be performed using he DATA+ buon or DATA buon as he acual saus is checked. TCR : : : TCR : : : TV monior TV monior 21

22 Superimpose Screens Operaion mode The value o be displayed can be seleced using seup menu iem No.001 DISPLAY SEL. (See page 28) TIME: Couner value T&STA: Couner value and VTR operaion mode T&R: Couner value and remaining ape amoun T&S&R: Couner value, VTR operaion mode and remaining ape amoun TIME mode TCR : : : TV monior T&STA mode Couner value <Noes> One of he following errors may be displayed on he hird line (remaining ape amoun line) in he T&S&R mode. (See page 74) [NO RF]: This appears when a blank par has been deeced on he ape. E-09 appears on he fron panel s couner display. [LOW RF]: This appears when here is no head oupu. E-01 appears on he fron panel s couner display. [FAN STOP]: This appears when he cooling fan has shu down. E-70 and he couner value appear alernaely on he fron panel s couner display. [SERVO NOT LOCKED]: This appears when he servo is no locked. E-00 appears on he fron panel s couner display area. TCR : : : STOP Couner value VTR operaion mode T&R mode TV monior TCR : : : REMAIN : Couner value Remaining ape amoun TV monior T&S&R mode TCR : : : STOP REMAIN : TV monior Couner value VTR operaion mode Remaining ape amoun 22

23 Seup (Iniial Seings) The uni s main seings can be performed and checked using he on-screen menus which appear on he video monior conneced o he uni. I is also possible o perform and check he seings using he iem numbers and seing numbers which appear on he fron panel s display. One user seing memory se is provided wih he uni o enable he desired seings o be sored in he memory ahead of ime for use. How o perform he seings using he on-screen menus 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 SET UP MENU MAIN NO SYSTEM 000 BASIC 100 OPERATION 200 INTERFACE 400 TAPE PROTECT 500 TIME CODE 600 VIDEO 700 AUDIO END In he menu seing mode, he REW, STOP, FF, PLAY, PAUSE/STILL and REC buons serve as he MODE, MENU-DOWN, MENU-UP, DATA, DATA+ and SET buons. Press he MENU-UP buon or MENU-DOWN buon o move he cursor ( ) o he menu where he changes are o be made. 3 Press he SET buon o se he iem. To reurn o he menu screen, press he SET buon while holding down he MODE buon. 4 Press he MENU-UP buon or MENU-DOWN buon o move he cursor ( ) o he iem where he changes are o be made. The page can be scrolled up or down by pressing he MENU-UP buon or MENU-DOWN buon while holding down he MODE buon. 5 Press he DATA+ or DATA buon o change he seing. The seing value will flash while changes o he seing are being performed. 6 Press he SET buon o ener he seing. To change anoher iem, repea seps 4, 5 and 6. The seing can be canceled by pressing he MODE buon. To change anoher iem wihou enering a seing, press he MODE buon, and repea seps 4, 5 and 6. 7 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The menu seing procedure is now erminaed. How o resore he facory seings 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 Press he RESET buon. The uni is se o he defaul seing mode, and he defaul seing screen appears on he video monior. SELECT MODE ESCAPE LOAD SAVE PROTECT 23

24 Seup (Iniial Seings) 3 Press he MENU-UP buon or MENU-DOWN buon o posiion he cursor a LOAD, and press he SET buon. The uni is se o he LOAD mode, and he LOAD screen appears on he video monior. SET UP MENU <LOAD> NO FACTORY (ALL) FACTORY (NOT SYSTEM) USER (ALL) USER (NOT SYSTEM) 4 Press he MENU-UP buon or MENU-DOWN buon o move he cursor o FACTORY (ALL), and press he SET buon. OIf he cursor is moved o FACTORY (NOT SYSTEM) and his operaion is performed, all he menus excep he SYSTEM menu will be resored o he facory seings. OIf he cursor is moved o NO and his operaion is performed, operaion will reurn o he menu screen wihou resoring he facory seings. 5 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The menu seing procedure is now erminaed. How o se he user defaul seings 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 Performs seps 2 hrough 6 of How o perform he seings using he on-screen menus, and change o he desired seings. (See page 23) 3 Press he RESET buon. The uni is se o he defaul seing mode, and he defaul seing screen appears on he video monior. SELECT MODE ESCAPE LOAD SAVE PROTECT 4 Press he MENU-UP buon or MENU-DOWN buon o posiion he cursor a SAVE, and press he SET buon. The uni is se o he SAVE mode, and he SAVE screen appears on he video monior. SET UP MENU <SAVE> NO USER (ALL) USER (NOT SYSTEM) 5 Press he MENU-UP buon or MENU-DOWN buon o move he cursor o USER (ALL), and press he SET buon. OIf he cursor is moved o USER (NOT SYSTEM) and his operaion is performed, all he menus excep he SYSTEM menu will be updaed. OIf he cursor is moved o NO and his operaion is performed, operaion will reurn o he menu screen wihou updaing he seings. 6 The screen o confirm wheher SAVE is o be iniiaed or canceled now appears. Press he MENU-UP buon or MENU-DOWN buon o move he cursor o he YES posiion, and press he SET buon. The seings are now saved in he memory. SAVE OK? NO YES 7 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The menu seing procedure is now erminaed. 24

25 Seup (Iniial Seings) How o load he user defaul seings 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 Press he RESET buon. The uni is se o he defaul seing mode, and he defaul seing screen appears on he video monior. SELECT MODE ESCAPE LOAD SAVE PROTECT 3 Press he MENU-UP buon or MENU-DOWN buon o posiion he cursor a LOAD, and press he SET buon. The uni is se o he LOAD mode, and he LOAD screen appears on he video monior. SET UP MENU <LOAD> NO FACTORY (ALL) FACTORY (NOT SYSTEM) USER (ALL) USER (NOT SYSTEM) 4 Press he MENU-UP buon or MENU-DOWN buon o move he cursor o USER (ALL), and press he SET buon. OIf he cursor is moved o USER (NOT SYSTEM) and his operaion is performed, he user seings for all he menus excep he SYSTEM menu which are saved in he memory will be used for operaion. OIf he cursor is moved o NO and his operaion is performed, operaion will reurn o he menu screen wihou any changes made o he user seings which are saved in he memory. 5 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The menu seing procedure is now erminaed. How o iniiae he menu proec mode By seing he uni o he menu proec mode, he opening of he seup menus can be disabled even if he fron panel s LOCAL/MENU/REMOTE swich is se o he MENU posiion. 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 Press he RESET buon. The uni is se o he defaul seing mode, and he defaul seing screen appears on he video monior. 3 SELECT MODE ESCAPE LOAD SAVE PROTECT Press he MENU-UP buon or MENU-DOWN buon o posiion he cursor a PROTECT, and press he SET buon. The uni is now se o he menu proec mode, and he screen o confirm wheher menu proec is o be iniiaed or canceled now appears on he video monior. MENU PROTECT OK? NO YES 4 Press he MENU-UP buon or MENU-DOWN buon o move he cursor o he YES posiion, and press he SET buon. The menu screen now appears. 25

26 Seup (Iniial Seings) 5 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The uni is now se o he menu proec mode. When he LOCAL/MENU/REMOTE swich is se o he MENU posiion, MENU PROTECTED appears on he video monior screen insead of he menu seing mode being esablished. If, while he menu proec menu is se, he LOCAL/MENU/REMOTE swich is se o he menu posiion while he fron panel s COUNTER buon is held down, he menu seing mode will be esablished, and regular menu seings can be performed. Perform seps 2 hrough 7 in How o perform he seings using he on-screen menus. (See page 23) How o release he menu proec mode 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion while holding down he fron panel s COUNTER buon. The uni is now se o he menu seing mode, and he menu screen appears on he video monior. 2 Perform seps 2 and 3 of How o iniiae he menu proec mode described above. The screen o confirm wheher menu proec is o be iniiaed or canceled now appears on he video monior. MENU PROTECT OK? NO YES 3 Press he MENU-UP buon or MENU-DOWN buon o move he cursor o he NO posiion, and press he SET buon. The menu proec mode is now released. How o display he DIAG menu This uni incorporaes a funcion for displaying he HOURS METER and sofware program version on he video monior. 1 Se he LOCAL/MENU/REMOTE swich o he MENU posiion while holding down he EJECT buon. The uni is now se o he DIAG display mode, and he HOURS METER appears on he video monior. DIAG MENU HOURS METER H0 OPERATION 0H H1 DRUM RUN 0H H2 TAPE RUN 0H H3 THREADING 0T 2 Wih he HOURS METER displayed, press he MENU-UP buon or MENU-DOWN buon while holding down he MODE buon. The sofware program version is displayed on he video monior. The fron microcompuer version appears on he fron panel s couner display. DIAG MENU VERSION <NTSC> IF AV-SYSCON SBC CYLINDER REEL END When he MENU-UP buon or MENU-DOWN buon is pressed again while holding down he MODE buon, he HOURS METER display is resored. 3 Se he LOCAL/MENU/REMOTE swich o he LOCAL or REMOTE posiion. The normal mode is now resored. 26

27 Seup Menus SYSTEM menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 00 SYSTEM H 128 For adjusing he horizonal phase. This iem enables he phase o be varied by up o ±1.5 µ SC COARSE SC FINE SCH COARSE SCH FINE VIDEO LEVEL SET UP LEVEL HUE CHROMA LEVEL For coarsely adjusing he subcarrier phase. 90 This iem enables he phase o be varied by selecing one of 4 posiions a degree incremens For finely adjusing he subcarrier phase. This iem enables he phase o be varied by up o 90 degrees. By using his iem in andem wih SC COARSE, any seing up o 360 degrees can be achieved For coarsely adjusing he SCH (Sub Carrier o Horizonal) phase. 90 This iem enables he phase o be varied by selecing one of 4 posiions a degree incremens For finely adjusing he SCH (Sub Carrier o Horizonal) phase. This iem enables he phase o be varied by up o 90 degrees. By using his iem in andem wih SCH COARSE, any seing up o 360 degrees can be achieved For seing he video level. This iem enables he video level o be varied by up o ±3 db For seing he seup amoun. This iem enables he seup amoun o be varied by up o 10 IRE For seing he hue. This iem enables he hue o be varied by up o ±25 degrees For seing he chroma level. This iem enables he chroma level o be varied by up o ±3 db The underlining denoes he facory mode seing. <Noes> OIem numbers 05, 06, 07 and 08 are iniialized only when ALL has been seleced by he iniializaion operaion. O The seing iems are no iniialized by he regular menu rese operaion. The uni is shipped wih he seings already adjused. 27

28 Seup Menus BASIC menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 000 SUPER 001 DISPLAY SEL CHARA H-POS CHARA V-POS 0003 For seing wheher o show he superimposed display from he MONITOR OUT connecor. OFF 0: The superimposed display is no shown. ON 1: The superimposed displayed is shown. For seing wha is o be shown by he superimposed display from he MONITOR OUT connecor. TIME 0: Only he ime is displayed. T&STA 1: The ime and operaion mode are displayed. T&R 2: The ime and remaining ape amoun are displayed. T&S&R 3: The ime, operaion mode and remaining ape amoun are displayed. 0 For seing he horizonal posiion of he superimposed characers. 1 (10 seps) For seing he verical posiion of he superimposed characers. 1 (23 seps) CHARA TYPE For selecing he ype of characers for he superimposed and menu displays. WHITE 0: Whie characers on a black background W/OUT 1: Whie characers wih black oulines The underlining denoes he facory mode seing. If he DATA+ buon or DATA buon is pressed wih he MODE buon held down when he CHARA H- POS and CHARA V-POS iems are being se, he couner display appears emporarily, and he posiions can be se while he acual saus is moniored. 28

29 Seup Menus OPERATION menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 100 LOCAL ENABLE 101 TAPE TIMER 102 S/F/R EE SEL 103 WIDE MODE 104 TAPE IN MOD 105 TAPE END MOD 106 AUTO BACK 107 FORMAT SEL 108 REC INHIBIT 109 CAP. LOCK 110 FF. REW MAX 111 MEMORY MODE BGN PRESET For seing he BEGIN poin. 113 END PRESET For seing he END poin. For selecing he swiches which can be operaed on he fron panel in he REMOTE mode. DIS 0: None of he swiches can be operaed. ST&EJ 1: Only he STOP swich and EJECT swich can be operaed. For selecing he CTL couner display. 12H 0: ±12-hour display 24H 1: 24-hour display For selecing he EE or VV oupu in he STOP, FF or REW mode. EE 0: E-E (elecric modulaion o elecric playback) is oupu. TAPE 1: V-V (VTR o VTR recording) is oupu. For selecing he WIDE mode. AUTO 0: The mode is deeced auomaically. WIDE 1: The mode is forcibly reaed as WIDE. NORMAL 2: The mode is forcibly reaed as NORMAL. For selecing he operaion which is o be performed when he cassee has been insered ino he uni. STOP 0: STOP REW 1: REWIND PAUSE 2: PLAY PAUSE PLAY 3: PLAY For selecing he operaion which is o be performed when he ape has arrived a he end. STOP 0: STOP REW 1: REWIND REW EJ 2: The ape is rewound and, upon compleion of rewinding, i is ejeced. EJECT 3: EJECT For selecing wheher he ape is be auomaically rolled back in order o ensure frame o frame coninuiy. OFF 0: The ape is no auomaically rolled back. ON 1: The ape is auomaically rolled back. For selecing he forma when an L cassee is o be used. DVCPRO 0: DVCPRO mode DV 1: DV mode DVCAM 2: DVCAM mode For selecing wheher o inhibi recording on he uni. OFF 0: Recording is allowed. ON 1: Recording is inhibied. For selecing he capsan lock mode. 2F 0: The 2F lock mode is seleced for he capsan. 4F 1: The 4F lock mode is seleced for he capsan. For seing he maximum FF and REW speed. X32 0: 32 imes normal ape speed X60 1: 60 imes normal ape speed For seing he memory operaion. OFF 0: The memory operaion is no performed. M-STOP 1: The ape is sopped during FF or REW near he BEGIN poin. REPT1 2: When he ape arrives a he end, i is rewound o he BEGIN poin where i sops. CONT 3: When he ape arrives a he end, i is rewound o he BEGIN poin and played. This sequence is repeaed. The underlining denoes he facory mode seing. 29

30 Seup Menus INTERFACE menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 200 BAUD RATE DATA LENGTH 202 STOP BIT 203 PARITY 204 ACK RETURN C ID SEL For seing he RS-232C ransmission speed (baud rae) BIT For seing he RS-232C daa lengh. 7BIT 1BIT For seing he RS-232C sop bi. 2BIT For seing none, odd or even as he RS-232C pariy bi. NONE 0: The pariy bi is no used. ODD 1: Odd pariy is used for he pariy bi. EVEN 2: Even pariy is used for he pariy bi. For seing he RS-232C reurn daa. OFF 0: The ACK code is no reurned. ON 1: The ACK code is reurned. For seing he RS-232C device ID. D250 0: The ID of he AJ-D250 is reurned. Use his seing when exercising conrol using he AJ-A250 or a compuer. D230 1: The ID of he AJ-D230 is reurned. Use his seing when exercising conrol using he AJ-A571. When he AJ-A571 is used for conrol, he uni can be used as a player VTR. The underlining denoes he facory mode seing. 30

31 Seup Menus TAPE PROTECT menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 400 STILL TIMER SRC PROTECT 402 DRUM STDBY 403 STOP PROTECT 0.5s For selecing he ime aken for he ape proecion mode o be esablished 5s when he uni has been lef sanding in he STOP, PLAY, PAUSE or STILL 10s mode. 30s (Unis = s: seconds, min: minues) 1min OWhen he uni has been lef sanding in he REC PAUSE mode, he ime 2min aken for he ape proecion mode o be esablished is fixed a 2 minues. For seing he ape proecion operaion when he uni has been lef sanding in he PAUSE mode. STEP 0: Sep (sep FWD in STILL or PAUSE mode; sep REV in REC PAUSE mode) HALF 1: Half loading (STANDBY OFF) For seing he mode in which he drum is o be sopped during STANDBY OFF. OFF 0: The drum is sopped during STANDBY OFF. ON 1: The drum roaes a all imes. For seing he ape proecion operaion when he uni is lef sanding in he STOP mode. STEP 0: Sep HALF 1: Half loading The underlining denoes he facory mode seing. When a consumer-use DV forma ape is used, he ape proecion mode will be esablished in 10 seconds even if 30s, 1min or 2min is seleced as he STILL TIMER iem seing. 31

32 Seup Menus TIME CODE menu Iem Seing No. Superimposed display No. Superimposed display Descripion of seing 500 VITC POS VITC POS L For seing he posiion where he VITC signal is o be insered. 11L (The same line as he one se for he VITC POS-2 iem canno be seleced.) 16L 20L 10L For seing he posiion where he VITC signal is o be insered. 11L (The same line as he one se for he VITC POS-1 iem canno be seleced.) 18L 502 VITC BLANK 503 TCG REGEN 504 BINARY GP 505 DF MODE 506 TC MODE L For seing wheher he VITC signal is o be oupu. BLANK 0: The VITC signal is no oupu. THRU 1: The VITC signal is oupu. 507 TC PRESET For seing he TCG value. For selecing he signal o be regeneraed when he ime code generaor (TCG) is in he regeneraion mode (iem No.506). TC&UB 0: Boh TC and UB are regeneraed. TC 1: Only TC is regeneraed. UB 2: Only UB is regeneraed. For seing he saus for using he user s bi of he TCG : No specified (a characer se is no used) : ISO characers (8-bi characer se complying wih ISO646, ISO2022) 010 2: Unassigned 1 (undefined) 011 3: Unassigned 2 (undefined) 100 4: Unassigned 3 (undefined) 101 5: Page/line (page/line muliplex sysem complying wih SMPTE262M) 110 6: Unassigned 4 (undefined) 111 7: Unassigned 5 (undefined) For seing drop frame or non-drop frame for he CTL and TCG. DF 0: The drop frame mode is esablished for operaion. NDF 1: The non-drop frame mode is esablished for operaion. For seing he TCG mode. P-REC 1: PRESET of he inernal TC is used in he REC RUN mode. P-FREE 0: PRESET of he inernal TC is used in he FREE RUN mode. I-REG 2: The inernal TC is used in he regeneraion mode. E-VITC 3: The inpu video signal VITC is used in he regeneraion mode. 508 UB PRESET For seing he user s bi value. 509 TCG CF FLAG For seing he CF flag of he TCG o ON or OFF. OFF 0: The CF flag is se o OFF. ON 1: The CF flag is se o ON. The underlining denoes he facory mode seing. 32