Solatube Brighten Up Series

Transcription

1 Slatube Brighten Up Series Slatube 160 DS (250mm diameter) & Slatube 290 DS (350mm diameter) Prduct Installatin Guide *Plycarbnate rf dme with Raybender 3000 Technlgy Please read this guide fully befre beginning installatin *Rf flashing (as specified, supplied with flashing insulatr) *Tp tube assembly (adjustable angle system) Suggested tls required fr drill and drill bits screwdrivers hammer wire fr prbing sealant gun Slatube installatin: magnetic cmpass angle grinder/rf tile cutter/slate claw subject t rf type sabre/reciprcating saw keyhle saw tape measure plumb line scissrs r blade knife trch retaining wire (less than 3mm thick) Slatube Base Kit Items marked * cmprise the Slatube base kit which is suitable fr installatins with a rf t ceiling distance f up t 400mm. Fr distances greater than this, extensin tubes will be required please see chart right. *Seal & fastener kit (nt shwn) Flashing sealant (if specified) Aluminium tape rll Flashing screws (53mm) Dme ring screws (25mm) Tube screws (15mm) Ceiling flange screws (40mm) Expansin jint seal LightTracker dme reflectr (fr use nly n steep, nrth facing rfs r wall munted installatins) Extensin tubes 610mm lng (quantity as specified) *Bttm tube assembly (adjustable angle system) *Decrative fixture/ Diffuser and natural effect lens Additinal extensin tubes? Yu will receive a tp tube and bttm tube assembly in yur Slatube kit. Tgether these assemblies give an install distance (rf t ceiling) f up t 400mm (16"). This is generally sufficient fr flat rfs, vaulted ceilings, r very shallw pitch rfs. Fr greater install distances please check yu have purchased sufficient extensin tubes t meet yur required install distance: Install distance up t mm (inches) Extensin tubes req Add rlls f tape 160 DS 290 DS 400 (16 ) (38 ) (60 ) (82 ) (104 ) (126 ) (148 ) (170 ) Please ensure that all cmpnents have arrived in perfect cnditin befre starting the installatin. See fr full Terms & Cnditins. ML-INST-BU14

2 Warning D nt prceed with the installatin until yu have read and understd the entire installatin guidelines, including the pints belw. If yu have any questins r require clarificatin f any installatin prcedures, please cntact yur Slatube supplier. Slatube (r seller) assumes n respnsibility r bligatin whatsever fr the failure f an architect, cntractr, installer r building wner t cmply with all applicable laws, rdinances, building cdes, energy cdes, fire and safety cdes and requirements, and adequate safety precautins. Installatin f this prduct shuld be attempted nly by individuals skilled in the use f the tls and equipment necessary fr installatin. The supplier accepts n respnsibility fr incrrectly installed r nn-apprpriate applicatins. Prtect yurself and all persns and prperty during installatin. If yu have any dubt cncerning yur cmpetence r expertise, cnsult a qualified expert befre prceeding. In additin, please check the Health & Safety Executive website fr advice n safe wrking at height Installatin is at yur wn risk. Slatube prduct installatins may be dangerus wing t the lcatins f the wrk t be undertaken. The hazardus cnditins include, but are nt limited t, the fllwing: During installatin, the Slatube reflective tubes may fcus sunlight ptentially causing cncentrated light and heat. Keep the prtective film n the reflective tubing prir t installatin and the tubing away frm ptentially flammable material. Sheet metal edges may be sharp. Use prtective glves t avid laceratins. Installatin may require climbing and wrking at dangerus heights, including n ladders, scafflding, rfs and in attic spaces. Use extreme cautin t minimize risk f accidental injury and prperty damage including, but nt limited t, the pints belw: D nt wrk alne we recmmend a team f at least tw peple Clear the area belw yur wrkspace f all peple, animals and ther items. Avid wrking n surfaces that are slippery r wet and use ftwear with excellent tractin. Use nly strng, well-supprted and apprpriate ladders. Wrk nly in calm, dry weather. When in the attic, ensure that yur weight is supprted at all times with structurally sund framing; dry wall material is nt designed t carry a persn s weight. Reduce the risk f fire, electric shck, and persnal injury by fllwing basic safety precautins when using electric tls; always wear safety gggles r ther suitable eye prtectin and ensure wrk area is clear f all electrical wires, gas pipes, water pipes and ther bstacles. When wrking in the attic r ther dusty areas, use f a mask r respiratr is recmmended t avid lung irritatin. Attic spaces may be dark, cnfined, and subject t extreme temperatures. Beware f sharp prtruding bjects. D nt attempt installatin withut having smene within range f yur vice r clse enugh t cme t yur aid if necessary. Only suitably qualified persns shuld undertake any electrical wiring. Installatin tips & safety advice This guide ffers a step-by-step guide fr the installatin f a Slatube 160DS and 290DS. In general, a Slatube 160DS can prvide enugh daylight t illuminate a dark area f up t 10 sqm. A Slatube 290DS can prvide enugh daylight t illuminate a dark area f up t 18 sq m. Bth examples are based n a 2.44 m ceiling height with a 1.83 m tube length. Fr larger areas, yu may need t install mre than ne Slatube. This infrmatin is fr guidance purpses nly. Allw at least 4 hurs fr the installatin, particularly if this is yur first installatin. During the day, turn ff all the lights in the rm t see hw much natural light cmes in thrugh the windws (if any). Yu shuld then be able t determine the best psitin fr the Slatube diffuser. Avid rf dme lcatins shaded by trees, ridges and chimneys, r near water channels r valleys. Avid attic areas with bstructins such as gas, water r drain pipes, air ducts, flues r furnaces, fixed strage tanks. Measure the distance between the rf and the ceiling t ensure yu have rdered sufficient reflective tubing t cver the distance. All reflective extensin tube jints shuld verlap a minimum f 50mm and be fixed tgether using the aluminium tape (and self-tapping screws if required). All adhesives, seals and tapes shuld be applied t a dry and dust-free surface. The ideal wrking temperature is apprximately 22 C. Ensure all jints (including seams) are taped sufficiently and all edges well rubbed in (tip: use the tape backing paper) t prevent the adhesive drying ut and t prevent insect and dust ingress. Ensure yur rf is in an apprpriate cnditin t supprt the wrk necessary fr a Slatube installatin withut damaging its waterprfing prperties. Slatube will generally perfrm best if the rf dme is lcated n the suth, east r west elevatin. If the rf dme is t be psitined n a nrth facing elevatin, psitining the rf dme as high as pssible n the rf will enhance perfrmance. Yu may chse t supprt any extensin tubes with a wire r similar retainer fixed t the rafters if the extensin tubes are at a significant angle away frm the vertical. When the Slatube is initially installed, it is nt uncmmn fr it t cndensate lightly n the inside f the dme fr the first few weeks until humid air inside the tube dissipates; the dme is designed t cllect any internal cndensatin and direct it t the utside f the flashing. The flashing insulatr prvided is essential t reduce the pssibility f cndensatin, but in particularly cld climates, it is als advisable t tape a jacket f insulating material (ptinal extra) arund the utside f the extensin tubes and up int the vid between the tp tube assembly and rf flashing; this is t prevent the pssibility f cndensatin build-up n the exterir f the cmpnents within the rf vid. Page 2

3 Diagram D Diagram C Diagram B Diagram A Slatube 160 DS & Slatube 290 DS Prduct Installatin Guide Step 1 Selecting the lcatin fr the ceiling diffuser Decide n the preferred lcatin fr yur ceiling diffuser. Lcate this pint in the rf vid it may help if yu measure the distance frm yur lft hatch t the desired lcatin first r use ther clues such as spt lights, light fittings r flues t cnfirm the lcatin. Find a clear space between jists as clse t the desired lcatin as pssible and unbstructed by pipes, cables r ther bstacles. Draw a 275mm circle fr the 160DS r a 375mm circle fr the 290DS n the upper side f the plasterbard ceiling. D nt cut the ceiling hle until yu are sure that the rf flashing will als fit in the desired lcatin and that the tp and bttm tube assemblies will align. 275mm Ø hle fr 160DS 375mm Ø hle fr 290DS and the rf flashing The rf flashing can be psitined either vertically abve the diffuser lcatin r up t an angle f 30 frm vertical in any directin frm the diffuser psitin by rtating the tw angle adaptrs supplied (diagram A). The diagram shws tw pssible psitins fr the rf flashing relative t the psitin f the tp and bttm tube assemblies. Nte: 0-90 angle adaptrs are available if a greater degree f variatin is required. r Ensure that the rute between the rf flashing and the ceiling diffuser is clear and unbstructed. Step 2 Mark the rf flashing and diffuser psitin Cut a small hle in the rf felt and identify the rf psitin (tile) frm inside using a lng nail r wire prbe s yu can lcate it again later frm the rf side Once yu are sure that the circle yu drew earlier n the upper side f the plasterbard ceiling is in the crrect lcatin, screw a marker screw thrugh the ceiling frm abve, leaving apprximately an inch shwing in the rf vid yu can use this later as a handle when cutting the hle (diagram B). Rf Ceiling Step 3 Cnfirm and cut the diffuser lcatin Check the marker screw frm the rm belw t cnfirm the centre f the diffuser lcatin is crrect. In the rf vid, cut arund the marked circle, taking care t hld nt the screw handle t prevent the cut-ut falling (diagram C). Tip: T cntain dust and debris when cutting the ceiling hle, ne persn culd hld an empty bx under the ceiling while the ther cuts the hle frm abve. Alternatively, lay a dust sheet belw. Step 4 Installing the bttm tube assembly Insert the bttm tube assembly up int the ceiling and, if the installatin is nt vertical, rtate the angle adaptr t pint twards the rf flashing lcatin. Using a crsshead screwdriver, rtate and tighten tw f the twist-lck fastening clamps t temprarily attach the bttm tube assembly t the ceiling (diagram D). D nt remve the prtective liner frm the inside f the bttm tube at this pint. Tip: Affix a plastic bag ver the end f the bttm tube assembly t capture any dust and debris that may be created when carrying ut the rf wrks. Page 3

4 Diagram H Diagram G Diagram F Diagram E Step 5 Installing the rf flashing The rf flashing is supplied accrding t the rf type/flashing yu specified n yur rder. T cmplete this step, please refer t the separate rf flashing installatin guide supplied with the flashing Step 6 Aligning the tp tube assembly Insert the tp tube assembly int the rf flashing frm the utside. If necessary, rtate the angle adaptr s that the tp tube assembly pints twards the bttm tube assembly in the ceiling. The lengths L1 and L2 (diagram E) shuld be equal t ensure alignment. Nte: Fr flat rf/vaulted ceiling applicatins where n extensin tubes are required, the bttm tube assembly will be fitted up inside the tp tube assembly. L1 L2 r L1 L2 Step 7 Installing the tp tube assembly Remve the tp tube assembly frm the rf flashing. Tape the angle adaptr jint and tube seams f the tp tube assembly with the fil tape prvided (diagram F). Remve the prtective lining film frm the inside f the tube and insert the tp tube assembly int the rf flashing, aligning it again in the directin f the bttm tube assembly. Securely fasten the dme ring f the tp tube assembly t the flashing using the dme screws prvided. Ensure that the neprene seal is secured between the dme ring and the tp f the flashing upstand. Neprene seal Step 8 LightTracker reflectr (if used) The LightTracker reflectr shuld be used nly fr steep, nrth-facing rfs r wall munted applicatins; it is nt required fr flat rfs r suth, east r west rf aspects. Fr steep, nrth-facing rfs, psitin the LightTracker dme reflectr in the nrth side f the dme, with the reflective side facing due suth. Fr wall-munted applicatins the LightTracker shuld be placed at the bttm f the dme facing skywards. T fix the LightTracker in place, align the hles in the reflectr with the tabs inside the dme and snap int place. Peel the prtective film frm the reflectr (diagram G). Step 9 Installing the rf dme Align the fur tabs n the dme base with the snaps n the dme ring and press dwn firmly t click int place. Check t make sure the snaps are fully engaged (diagram H). Step 10 Cnnecting the tp tube assembly t the bttm tube assembly Fr shrt installatins with n extensin tubes prceed t Step 12. Fr lnger installatins with extensin tubes cntinue with Step 11. Page 4

5 Diagram L Diagram K Diagram J Diagram I Step 11 Assembling extensin tubes Remve the prtective liner frm the extensin tube(s) befre assembly. Extensin tubes have deep and shallw ntches at each end s that they may be frmed int slightly tapered tubes. Weave ne end f the tube thrugh a deep ntch, the ther end thrugh a shallw ntch, ensuring the tube is als held in the centre ntch (diagram I). Tape the tube seam with a shrt piece f fil tape at either end t hld the jints temprarily in psitin. The smaller diameter tube end shuld always pint twards the bttm tube assembly. Assemble all the required extensin tubes, telescping them tgether t prvide the ttal length f tube required and remembering t allw at least 50mm verlap at each jin. At this stage, use small pieces f fil tape t hld the tubes tgether. Check that the assembled tube length is crrect by hlding the extensin tube(s) alngside the tp and bttm tube assemblies. Adjust the tube length as necessary. Fr very lng r angled tube lengths, self-tapping screws are prvided t fasten the extensin tubes tgether. Tape all jints securely, smthing the tape t create a gd, firm seal. shallw ntch deep ntch Step 12 Applying the expansin jint seal Fr shrt installatins with n extensin tubes the expansin jint seal is applied 25mm frm the tp edge f the bttm tube assembly. Fr installatins using extensin tubes, the expansin jint seal is applied 25mm frm the tp edge f the uppermst extensin tube. The expansin jint seal shuld be applied t the utside diameter f the tube: remve the backing strip frm the expansin jint seal and adhere it 25mm frm the tp edge f the tube. The seal shuld wrap twice arund the tube, nt verlapping but butting up clsely (diagram J). expansin jint seal Step 13 Installing the bttm tube assembly If any angle adjustment is required t the bttm tube assembly t align it with the tp tube assembly this shuld be dne nw; use a crsshead screwdriver t lsen the twist-lck fastening clamps. Remve the assembly frm the ceiling, and rtate the angle adaptr if necessary t ensure alignment with the tp tube assembly and repsitin it back int the ceiling. If extensin tubes are being used please g t Step 14. If n extensin tubes are being used, tape the seams and re-insert the bttm tube assembly, sliding it up int the tp tube assembly and then lck all fur twist-lck fastening clamps int the ceiling (diagram K). Nte: If the ceiling clamps cannt be engaged wing t the thickness f the ceiling r because f prximity t jists, the bttm tube assembly can be secured with the screws prvided int the ceiling/jists thrugh screw psitin indicatrs in the ceiling flange. D nt ver tighten the bttm tube assembly t the ceiling as this may prevent fitting f the diffuser. Remve the prtective film frm the inside f the bttm tube assembly. Step 14 Installing extensin tubes Fr installatins with extensin tubes, remve the prtective film frm the inside f the bttm tube assembly and all ther tubing if nt already dne s. Tape the seams and re-insert the bttm tube assembly and then lck all twist-lck fastening clamps int the ceiling. Insert the extensin tube with the expansin jint seal (a) up int the tp tube assembly. Then insert the ther end (b) int the bttm tube assembly (diagram L). Ensure there is a minimum 50mm verlap at either end. Tape all jints tgether and use self tapping screws fr additinal rigidity if necessary. a b Page 5

6 Diagram M Step 15 Installing the effects lens and diffuser Insert the Effects lens straight up int the bttm tube assembly until it sits int the recess at the base f the bttm tube assembly, with the clear plastic tab pinting dwnwards. Then place the ceiling fitting up int the lwer edge f the bttm tube assembly, aligning the male and female lugs, and twist t secure in place (diagram M). Effects lens In rder t clean the diffuser, r t replace the lamp in the ptinal Slatube integral electric light kit, yu may remve the diffuser by twisting the diffuser anti-clckwise t release it and then remve the lens by pulling gently dwn n the clear plastic lens tab. Ceiling fitting Yu have nw cmpleted installatin f yur Slatube Daylighting System. If yu have any questins regarding the installatin f yur Slatube Daylighting System please cntact us we shall be delighted t help. Telephne SlaLighting Limited 23 Osier Way, Olney Office Park, Olney MK46 5FP Tel: Fax: Web: daylight@slatube.c.uk Slalighting Limited Slatube ptins and accessries Slatube ffers an inspiring range f accessries that install neatly int yur Slatube Daylighting System transfrming it int a truly multi-functinal system. If yu have purchased any Slatube accessries, please read the instructins supplied with the accessry befre prceeding with the Slatube installatin as sme accessries cannt be installed as a retrfit. Integral electric light kit* Available fr bth Slatube sizes, prvides the cnvenience f a switched light fr night time use. Edisn screw fitting up t 75 watt. Additinal 0-90 angle Available fr bth Slatube sizes, allws easy installatin arund bstructins r crners. Bathrm ventilatin kit* Available fr the Slatube 160DS nly, ffers discreet style and high perfrmance, ideal fr bathrms and shwer rms (shwn with OptiView diffuser). Extensin tube Available fr bth Slatube sizes, may be jined tgether t meet the required install distance see frnt page fr details. Electric daylight dimmer kit* Available fr all Slatube sizes, cntrls the amunt f daylight required frm the cnvenience f a wall-munted switch r ptinal remte cntrl. Items marked * require cnnectin t an electrical circuit and we recmmend they are installed by a suitably qualified persn. Page 6

7 Slatube Prducts Ownership and Care Cngratulatins n the purchase f yur Slatube prduct UK PRODUCT REGISTRATION Please register yur Slatube prduct nline at r return the slip belw t Slalighting Limited, 23 Osier Way, Olney Office Park, Olney MK46 5FP. What des this warranty cver? Fr all prducts purchased r delivered hereunder, Slatube Internatinal Inc warrants they are free frm defects f wrkmanship and/r material fr a perid f time frm the date f purchase. Hw lng des the cverage last? Slatube Daylighting Systems Dmes, rf flashing bases, diffusers, diffuser ceiling muntings, reflective tubing, plastic, rubber r metal seals and gaskets, tapes and fasteners Slatube Electric Light Add-n Kit Slatube Daylight Dimmer Slar Star Slar panel and mtr Other Slar Star cmpnents, including metal husing, rf flashing bases, fan blade, plastic, rubber r metal seals, gaskets & fasteners Warranty perid 10 years 5 years 5 years Nn-Slatube branded r bespke prducts are subject t the manufacturer s wn warranty. What will Slalighting Limited d? 10 years Shuld any prducts be determined by Slalighting Limited t be defective, at the ptin f Slalighting Limited, such prducts will be repaired r replaced and returned within a reasnable time t the Buyer free frm defect. If Slalighting Limited prvides a replacement prduct, the warranty n the replacement will last nly fr the balance f the riginal prduct warranty perid. Slalighting Limited shall nt be respnsible fr installatin f replacement prducts. What are the limitatins n a buyer s remedies? IN NO EVENT WILL SOLALIGHTING LIMITED BE LIABLE FOR LOSS OF PROFITS, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL OR OTHER SIMILAR DAMAGES. IF SOLALIGHTING LIMITED DID NOT INSTALL THE PRODUCT(S), IN NO EVENT WILL SOLALIGHTING LIMITED BE LIABLE FOR ANY BREACH OF WARRANTY FOR IMPROPER INSTALLATION. TO THE FULLEST EXTENT ALLOWED BY LAW, SOLALIGHTING LIMITED S LIABILITY TO ALL BUYERS FOR ALL CLAIMS WITH RESPECT TO THE PRODUCTS WILL BE LIMITED TO THE LESSER OF (A) THE COST OF REPLACING THE PRODUCTS; (B) THE COST OF OBTAINING EQUIVALENT PRODUCTS; OR (C) THE COST OF HAVING PRODUCTS REPAIRED. What is nt cvered by this warranty? Slalighting Limited is nt respnsible fr nr des this warranty apply t: Labur r installatin f the prducts Prduct r perfrmance defects as a result f installatin nt in accrdance with Slalighting Limited s installatin guide r in nnstandard applicatins Defects r damages arising ut f shipment by cmmn carriers, private transprtatin r ther means f transprtatin Defects r damages arising ut f imprper handling r cleaning, accidents, acts f Gd, intentinal acts, misuse r abuse, r any ther circumstances beynd the cntrl f Slalighting Limited Cndensatin r any water damage resulting frm cndensatin Prducts subject t stress resulting frm (i) lcalized applicatin f heat, (ii) mvement f building and/r building cmpnents, r (iii) expansin r cntractin f framing members Accessries, flashing r ther installatin materials manufactured r sld by persns ther than Slalighting Limited Hw d I make a warranty claim? This warranty is subject t Yu cmpleting and returning ur warranty card r website warranty frm prmptly after purchase. Statutry rights are nt affected. Within seven (7) days f discvery f a defect, Buyer shuld cntact (i) Buyer s Slatube Distributr r (ii) Slalighting Limited. What warranties is Slalighting Limited disclaiming? TO THE EXTENT PERMITTED BY LAW WE DISCLAIM ALL OTHER WARRANTIES WITH REGARDS TO THE PRODUCTS EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF SATISFACTORY QUALITY OR FITNESS FOR ANY PARTICULAR PURPOSE. FOR FURTHER INFORMATION REGARDING WARRANTY LIMITATIONS PLEASE SEE ALSO SOLALIGHTING TERMS & CONDITIONS OF SALE AT Purchase details: Purchaser Name: Prduct details: Quantity Slatube 160DS Purchaser Address: Quantity Slatube 290DS Quantity Slatube 330DS Purchaser Telephne: Quantity Slatube Bathrm Vent Kit Hw did yu discver Slatube? Internet search/exhibitin/magazine/ther Quantity Slatube Electric Light Kit Date f purchase: Quantity Slatube Daylight Dimmer Name f supplier: Quantity Slar Star (state mdel) Name f installer: Invice number(s): Hw did we d? Please rate the fllwing s that we may better serve yu and ther custmers in the future (1 = pr, 10 = excellent) Quality f prduct Price Ease f installatin Custmer service Wuld yu recmmend Slatube prducts? Y / N Cmments: Page 7

8 Prduct Cleaning and Care Slatube Daylighting Systems Dme The dme n the Slatube Daylighting System is designed t be self-cleaning and requires n maintenance. Diffusers r Glass Decrative Fixtures Brighten Up Series Diffuser r Decrative Fixtures (Slatube 160 DS and 290 DS) Remve the diffuser r glass decrative fixture by carefully twisting cunter-clckwise t separate it frm the ceiling ring. T clean, wipe the diffuser r glass decrative fixture with a tissue r sft clth. T reattach, align the tabs n the diffuser r glass decrative fixture t thse n the ceiling ring and twist clckwise t secure. SlaMaster Series Open Ceiling Diffuser (Slatube 330 DS) Please cntact yur Slatube distributr r dealer fr care instructins. SlaMaster Series Clsed Ceiling Diffuser (Slatube 330 DS) Remve the diffuser by releasing the tabs n the diffuser frame frm the transitin bx. T clean, wipe the diffuser with a tissue r sft clth. T reattach the diffuser, psitin the diffuser panel int the transitin bx and secure the tabs int the ntches. Accessries Slatube Bathrm Ventilatin Add-n Kit Ensure appliance is switched ff and clean external surfaces nly with a damp clth; d nt wipe mtr r electrical parts. Slatube Electric Light Add-n Kit T replace the lamp in a Slatube light fixture, turn ff the light at the switch then fllw the abve instructins t remve the diffuser r glass decrative fixture, then remve the Natural Effect Lens by pulling n the tab. Replace the lamp then re-insert the Natural Effect Lens and reattach the diffuser r glass decrative fixture as described abve. Slalighting Limited 23 Osier Way, Olney Office Park, Olney MK46 5FP T F This warranty is applied by Slalighting Limited (Registered in England n ) n behalf f Slatube Internatinal Inc. Page 8